Copyright © 2008. All rights reserved.
P-660W-Tx v2
ADSL Router over POTS/ISDN
Quick Start Guide
Version 3.40
03/2008
Edition 1
DEFAULT LOGIN
IP Address http://192.168.1.1
Password 1234
P-660W-Tx v2 Quick Start Guide
1
Overview
The P-660W-Tx v2 lets you:
• Set up a wireless network with IEEE 802.1b and IEEE 802.1g capability
• Set up a DSL connection to the Internet without the need for a modem
• Set up advanced router features, including a firewall and wireless security.
Follow these steps to set up a DSL connection to the Internet and a wireless network using
the P-660W-Tx v2.
1 Set Up Your Hardware, page 2
2 Configure the P-660W-Tx v2 for Internet Access, page 3
3 Set Up a Wireless Network, page 9
See the User’s Guide on the included CD for details on all of the P-660W-Tx v2’s features.
Insert the CD into your CD-ROM, if a screen does not pop-up, use Windows Explorer (My
Computer) to go to the CD-ROM (commonly drive D) and browse for the User’s Guide.
Internet
P-660W-Tx v2 Quick Start Guide
2
1 Set Up Your Hardware
1 Antenna: Point the antenna upwards (perpendicular to the ground).
2DSL: Connect the P-660W-Tx v2 to a telephone jack using a telephone wire.
3ETHERNET: Use an Ethernet cable to connect the Ethernet port on your computer to
the Ethernet port on the P-660W-Tx v2.
4POWER: Use the included power adaptor to connect the POWER socket to an
appropriate power source (see the User’s Guide for power adaptors specifications by
region).
5ON/OFF: Push the power switch to the ON position to turn on the P-660W-Tx v2.
DSL
ETHERNET
POWER
ON/OFF
1
2
5
3
RESET
4
P-660W-Tx v2 Quick Start Guide
3
Look at the LEDs (lights)
The DSL light blinks and then stays on when a DSL connection is detected. The
ETHERNET light turns on if your computer is properly connected to the P-660W-Tx v2
using the Ethernet cable. When you connect the power, the POWER light blinks and stays
on once the device is ready.
VCheck your connections if the POWER or ETHERNET light does not turn on. If
this doesn’t help, disconnect the P-660W-Tx v2 from its power source, wait for
a few seconds and turn it back on.
2 Configure the P-660W-Tx v2 for Internet Access
You may configure the P-660W-Tx v2 for Internet access in one of these ways:
• Use Zero Configuration to set up your Internet connection automatically in section 2.1.
• If Zero Configuration does not detect your Internet access settings, use the Connection
Wizard to configure Internet access settings in section 2.2.
2.1 Set up Internet Access with Zero Configuration
Launch your web browser and navigate to any website (for example, www.zyxel.com). The
P-660W-Tx v2 automatically detects and configures your Internet connection. This may
take about two minutes.
If you have a PPPoE or PPPoA
connection, a screen displays
prompting you to enter your
Internet account information.
Enter the user name, password
and/or service name exactly as
provided. Click Apply.
P-660W-Tx v2 Quick Start Guide
4
2.2 Set up Internet Access with the Connection Wizard
If Zero Configuration does not detect your Internet access settings, use the Connection
Wizard to set up Internet Access. Access the P-660W-Tx v2’s web configurator so you can
use the Wizard. (The web configurator is the P-660W-Tx v2’s software interface that lets
you configure settings on the P-660W-Tx v2.)
2.2.1 Access the Connection Wizard
1 Launch a web browser such as Internet Explorer.
Enter http://192.168.1.1 and press [ENTER].
2 The Password window displays. Enter the
password (1234 is the default) and click Login.
V If the login screen does not display, check your cable connections. If that
doesn’t help, check your web browser’s security settings. See the appendix
in the User’s Guide for more suggestions. If you’ve forgotten the password,
see the User’s Guide for instructions on using the RESET button.
3 Change the password and click Apply.
4 In the Site Map
screen, click
Connection
Setup.
P-660W-Tx v2 Quick Start Guide
5
2.2.2 Configure Internet Access and Local Network Settings with the
Connection Wizard
Use the Connection Wizard to set up access to the Internet through your ISP. These are
your WAN (wide area network) settings. Then use the Connection Wizard to set up the
connection from your computer to the P-660W-Tx v2. These are your LAN (local area
network) settings.
" Enter the Internet access information given to you by your ISP exactly in
each wizard screen. Follow the instructions in this guide or leave the field
blank or at its default setting. Click Next to continue or click Back to return
to the previous screen. Screen information is not saved when you click
Back. If your connection times out, log back in and restart the Wizard.
1 From the Mode drop-down list box, select
Routing if your P-660W-Tx v2 is a gateway
between the Internet and your local network and
you need routing features such as NAT (Network
Address Translation) or a firewall. Select Bridge
if your P-660W-Tx v2 is on a private network
behind a router, and you do not need routing
features such as NAT or a firewall.
2 Configure your Encapsulation, Multiplex and
other settings based on the settings your ISP
provides you.
Bridge
• If you selected Bridge and RFC 1483 in the previous screen, go to step 3 in this section.
• If you selected Bridge in step 1 of this sec-
tion and PPPoA, the following screen
appears. Type your User Name and Pass-
word. Select Nailed-Up Connection to set
a permanent connection which automatically
reconnects on disconnection. Select Con-
nect on Demand to allow connection only
when required and with an idle time-out
period (in seconds) in the Max. Idle Timeout
field. Click Next.
P-660W-Tx v2 Quick Start Guide
6
3 Check your WAN and LAN settings in the
screen that appears. Click Save Settings.
Go to step 9 of this section.
Routing
• If you selected Routing in step 1 of this section, one of the following four screens appears
depending on the Encapsulation you chose in step 1 of this section.
• PPPoA, PPPoE: Type your User
Name and Password.
• PPPoE, PPPoA, ENET: Select
Obtain an IP Address Automati-
cally if your ISP (Internet Service
Provider) assigns IP addresses
automatically. Otherwise, select
Static IP Address if your ISP has
assigned you an IP address.
Check with your ISP if you are
unsure of which setting to choose.
• PPPoA, PPPoE: Select Nailed-Up
Connection to set a permanent
connection which automatically
reconnects on disconnection.
Select Connect on Demand to
allow connection only when
required and with an idle time-out
period (in seconds) in the Max.
Idle Timeout field.
• PPPoE, PPPoA, ENET, RFC 1483: Select SUA Only for shared Internet access with a sin-
gle ISP. This is recommended. Otherwise, select None if accessing the Internet on a public
IP address, or select Full Feature for advanced NAT features. See your User’s Guide for
more details.
4 Click Next.
PPPoE
PPPoA
RFC 1483
ENET
P-660W-Tx v2 Quick Start Guide
7
5 Check your WAN and LAN settings in the screen that
appears. Click Change LAN Configuration to configure
the P-660W-Tx v2 for your local area network (LAN) and
go to step 6 of this section.
• Otherwise click Save Settings and go to step 9 of this sec-
tion.
6 If you clicked Change LAN Configuration,
the following screen appears.
• Type the IP address and subnet mask for the P-
660W-Tx v2 on your LAN.
• Disable the DHCP Server if another device on
your LAN, such as a router, already allocates IP
addresses, or devices on your LAN have static
IP addresses. Go to step 8 of this section.
Otherwise, if the P-660W-Tx v2 is to allocate IP
addresses on your LAN, enable the DHCP
Server. Computers on your LAN will then need
to be set to receive an IP address automatically.
See the User’s Guide for more information on
configuring this.
7 If you enable the DHCP Server, ensure the Client IP Pool Starting Address is on the
same domain as your LAN IP Address (that is, the first three parts of the IP addresses
are the same). If you were given DNS Server settings, type them here. Otherwise leave
the default settings.
8 Click Finish to save your settings and go to step 9 of this section. Otherwise, click Back
to check your settings as in step 5 of this section.
" If you change the P-660W-Tx v2’s LAN IP address, you must use the new
IP address if you want to access the web configurator again.
P-660W-Tx v2 Quick Start Guide
8
9 The P-660W-Tx v2 automatically tests
the connection to the computer(s)
connected to the LAN port. To test the
connection from the P-660W-Tx v2 to the
ISP, click Start Diagnose. Otherwise
click Return to Main Menu to go back to
the main screen.
V If the P-660W-Tx v2 cannot connect to the Internet, check the Internet
connection settings in the wizard. Make sure you entered the correct user
name and password if you are using PPPoE or PPPoA.
10 Congratulations. Open a web browser, such as Internet Explorer, to visit your favorite
website.
3 Set up a Wireless Network
Follow these steps to set up a wireless network.
3.1 Configure Wireless Settings on Your P-660W-Tx v2
1 Click the Wireless LAN
link under Advanced
Setup.
P-660W-Tx v2 Quick Start Guide
9
2 Click Wireless.
3 Select Enable Wireless LAN.
4 ESSID: Type the name (up to 32
characters) you want to give to your
wireless network.
5Channel ID: Change the Channel ID
from the default if interference is a
problem on your network.
6 Security Mode: Select the strongest
Security Mode that devices on your
wireless network support. WPA2-PSK
is a good choice for a home network. In
this screen, select WPA Compatible
and type a Pre-Shared Key using a
combination of letters and numbers
(8~63 characters long). Then click
Apply to save your settings.
" Write down the Pre-Shared Key and ESSID as you will need to use them
again when you connect your computer to the P-660W-Tx v2.
3.2 Connect to the P-660W-Tx v2 Wirelessly From Your Computer
You can now connect to your P-660W-Tx v2 via a wireless connection, and access the
Internet. You need the ESSID and also the Pre-Shared Key if you set up security in the
previous section. The connection procedure is shown here (using Windows XP as an
example).
1 Right-click the wireless adapter icon which appears in
the bottom right of your computer screen. Click View
Available Wireless Networks.
Write down the Pre-Shared Key!
P-660W-Tx v2 Quick Start Guide
10
2 Select the ESSID name you gave the P-
660W-Tx v2 and click Connect. (The ESSID
used here is an example.)
3 If you have set up wireless security, you are
prompted to enter a password. Enter the Pre-
Shared Key you set up in the previous section and
click Connect.
4 If you connected successfully, a message similar to the following
displays.
V If you cannot connect wirelessly to the P-660W-Tx v2, check that you are
using the same ESSID and security key on both the P-660W-Tx v2 and
your wireless client.
5 Congratulations! That completes the setup procedure for your P-660W-Tx v2. Open a
web browser, such as Internet Explorer, to visit your favorite website.
Procedure to View a Product’s Certification(s)
1 Go to www.zyxel.com.
2 Select your product from the drop-down list box on the ZyXEL home
page to go to that product's page.
3 Select the certification you wish to view from this page.
/
