Operator Manual
TVS-D 660 LC-Display
Version 2.1
Print: November 2004
071571441 ( BN_5714E )
Contents
Introduction 1-1
General notes ..........................1-2
Technical modifications ................................1-2
Copyright .......................................1-2
Version-History ....................................1-2
Explanation of warning and note symbols ............1-2
Information on How to Use This Manual .............1-3
Service Center ..........................1-4
Menu Operation 2-5
Menu Tree ............................2-6
HOME Menu
.............................2-7
SIGNAL PROCESSING Menu ............................2-9
BTSC SOUND UNIT MENU.............................2-10
Sound Unit Menu / BTSC GAIN ...........................2-10
Sound Unit Menu / MODULATOR .........................2-10
Sound Unit Menu / PRECORRECTION.......................2-11
AUDIO SOUND UNIT MENU (FM MONO) .....................2-12
Sound Unit Menu / SWITCH ............................2-12
Sound Unit Menu / AF GAIN ............................2-12
Sound Unit Menu / PREEMPHASIS ........................2-13
Sound Unit Menu / MODULATOR .........................2-13
Sound Unit Menu / PRECORRECT. ........................2-13
DUAL SOUND UNIT MENU.............................2-14
Sound Unit Menu / Switch..............................2-14
Sound Unit Menu / AF Gain .............................2-15
Sound Unit Menu / Preemphasis ..........................2-15
Sound Unit Menu / Coder Control ..........................2-15
Sound Unit Menu / Modulator ............................2-15
Sound Unit Menu / Precorrection ..........................2-16
NICAM SOUND UNIT MENU ............................2-17
Sound Unit Menu / NICAM Gain ..........................2-17
Sound Unit Menu / NICAM Encoder ........................2-18
Sound Unit Menu / Modulator ............................2-18
Sound Unit Menu / AF Gain .............................2-18
Sound Unit Menu / Preemphasis ..........................2-19
Operator manual
0 - 1 TVS-D 660 LC-Display
Contents
Sound Unit Menu / Modulator ............................2-19
Sound Unit Menu / Precorrection ..........................2-19
VISION UNIT Menu .................................2-20
VISION UNIT Menu / SWITCH ...........................2-21
VISION UNIT Menu / VF GAIN ...........................2-22
VISION UNIT Menu / CLAMPING..........................2-22
VISION UNIT Menu / PRECORRECTION (group delay) ..............2-23
VISION UNIT Menu / PRECORRECTION (linear) .................2-23
VISION UNIT Menu / PRECORRECTION (non-linear) ...............2-25
REF / LO UNIT Menu ................................2-26
With GPS ......................................2-26
Without GPS.....................................2-26
REF / LO UNIT Menu / GENERAL .........................2-27
REF/LO UNIT Menu / FAB .............................2-27
REF/LO UNIT Menu / SWITCH ...........................2-27
REF/LO UNIT Menu / 2nd SWITCH.........................2-28
REF/LO UNIT Menu / PLL..............................2-28
REF/LO UNIT Menu / DSM .............................2-28
REF/LO UNIT Menu / PRECORRECTION .....................2-28
REF/LO unit / UP-CONVERTER ..........................2-29
RF-Menu ......................................2-30
With RCU ......................................2-30
RF-UNIT Menu / GENERAL.............................2-30
RF-UNIT Menu / UP-CONVERTER .........................2-31
RF-UNIT Menu / BROADBAND AMPLIFIER ....................2-31
RF-UNIT Menu / PA or Amplifier ..........................2-31
RF-UNIT Menu / OUTPUT FILTER .........................2-31
RF-UNIT Menu / DIRECTIONAL COUPLER OR BBV ...............2-31
RF-UNIT Menu / DIRECTIONAL COUPLER 1 ...................2-32
RF-UNIT Menu / DIRECTIONAL COUPLER 2 ...................2-32
HISTORY Menu ...................................2-33
PREFERENCES Menu ...............................2-33
AMPL. Menu.....................................2-34
INSTAL. Menu....................................2-35
MISCELLANEOUS Menu ..............................2-37
MISCELLANEOUS Menu / ABOUT .........................2-37
MISCELLANEOUS Menu / DATE/TIME ......................2-37
MISCELLANEOUS Menu / SUPPLY VOLTAGES/CURRENTS ..........2-37
MISCELLANEOUS Menu / MODULE TEMPERATURES..............2-38
MISCELLANEOUS Menu / SPARE OPERATIONS.................2-38
MISCELLANEOUS Menu / SYSTEM DATA ....................2-39
MISCELLANEOUS Menu / OPERATION LOG ...................2-39
MISCELLANEOUS Menu / UNITS .........................2-40
Operator manual
TVS-D 660 LC-Display 0 - 2
Contents
MISCELLANEOUS Menu / DATA INTERFACE...................2-40
MISCELLANEOUS Menu / DATA INTERFACE ...................2-40
MISCELLANEOUS Menu / SETUP MODEM ....................2-42
Appendix 3-1
Errors, warnings and other information .............3-2
Errors .........................................3-2
Warnings .......................................3-4
Information ......................................3-5
Operator manual
0 - 3 TVS-D 660 LC-Display
Contents
Introduction
Operator manual
TVS-D 660 LC-Display 1 - 1
Introduction
General notes
Technical modifications
The information in this manual is subject to change at any time and without notice.
Copyright
This manual contains information protected by copyright. All rights reserved. No part of
this manual may be photocopied, otherwise reproduced or translated into another
language without the prior written consent of Harris.
ATTENTION: Take this manual with you whenever you are going to perform any
maintenance work.
Version-History
Version Issue DCN Remarks
1.0 February 2004
2002242
First release
2.0 August 2004 2002242 Second release
2.1 November 2004 2004109 Partly revised release
Explanation of warning and note symbols
WARNING: Indicates that ignorance or bad neglicence of the cautionary
measures listed may result in personal injury or equipment damage.
ATTENTION: Indicates that ignorance or bad neglicence of the cautionary
measures listed may result in equipment damage.
NOTE: Useful tips and information on practical application.
Operator manual
1 - 2 TVS-D 660 LC-Display
Introduction
Information on How to Use This Manual
This operator manual and the operating manual TVS-D 660 should be used side by
side, as the information in both manuals is interdependent.
NOTE: All necessary settings for the specific transmitter position have
already been entered in the factory. There is no need for any
re-adjustment!
Operator manual
TVS-D 660 LC-Display 1 - 3
Introduction
Service Center
Harris Broadcast Systems Europe Tel. +43-(0)5522/9011 2285
Customer Care Center E-fax: 001 321 674 - 2591
Oberer Paspelsweg 6-8 Email: [email protected].
A-6830 RANKWEIL-BREDERIS
Operator manual
1 - 4 TVS-D 660 LC-Display
Introduction
Menu Operation
Operator manual
TVS-D 660 LC-Display 2 - 5
Menu Operation
Menu Tree
Operator manual
2 - 6 TVS-D 660 LC-Display
Menu Operation
HOME Menu
The sub-menus are all accessible via keys.
In the HOME MENU the following parameters are permanently displayed:
Parameter Remark
L, R, M, A*, B* Indication of the operation mode toggels
between L (local) , R (remote), M
(monitoring), A* (active devices) and B*
(backup devices).
ERROR/ WARNING/ INFO Indication of present errors / warnings/
additional information
* only in a spare sytem
Three operation modes are available to meet different user requirements:
In the LOCAL operation mode remote control is completeley disabled (no remote control
- signalling depends on the local setting).
In the REMOTE operation mode (so in A and B ) local indication, but no local control is
possible.
In the MONITORING mode local control is possible only after entering the password
(local password-protected mode).
Use the remote switch on the front-panel to switch between local and remote operation
mode.
Move the cursor to SIGNALING IF LOCAL to switch the remote signalling for local
operations on or off.
NOTE: Only visible if the remote interface is selected in the installation
menu
Change to the ACCESS submenu in the MISCELLANEOUS menu to activate/deactivate
the MONITORING mode.
The active operation mode is indicated by the LC-display, which will change from L
(local / local with signalling “loc sig”) to R (remote) or M (monitoring).
Operator manual
TVS-D 660 LC-Display 2 - 7
Menu Operation
Move the cursor to ERROR / WARNING or INFO to view a record of errors, warnings
and other information. The record contains information about the module or unit the
messages are originating from, the type of information (E/W/I) and plain-text messages.
Max. 7 entries are listed in the record. The indication (e.g. WARNING) on the LCD
refers to the message type with the highest priority - errors rank above warnings and
other information.
Operator manual
2 - 8 TVS-D 660 LC-Display
Menu Operation
SIGNAL PROCESSING Menu
In the SIGNAL PROCESSING menu the following parameters are permanently
displayed:
Parameter Remark
VF-IN Indication of the VF input level
INPUT Indication of the availability of the input
signal (Smiley / Weepy) and the input
source (MAIN / AUX)
REF. FREQ. Indication of the reference signal for the
OCXO (10MHz oscillator)
(1pps, 100kHz, 500kHz,1MHz, 2,048MHz,
5MHz, 10MHz oscillator)
FREQ. Indication of the RF vision carrier
frequency
RATED RF LEVEL Indication of the rated RF output level
RF-OUT Indication of the deviation from the rated
RF-level in dB
Operator manual
TVS-D 660 LC-Display 2 - 9
Menu Operation
BTSC SOUND UNIT Menu
In the SOUND UNIT menu the following parameter is permanently displayed:
Parameter Remark
SND.CARR. DEV.
Indication of the sound carrier deviation
in kHz (The nominal deviation is 75 kHz).
Sound Unit Menu / BTSC GAIN
Parameter Remark
BTSC COMPOSITE INPUT GAIN
Sets the gain of the BTSC composite
input. The range is -9.9 to +6 dB. This
directly affects the sound carrier
deviation.
DETECTOR DECAY
Defines the speed at which the indication
bar returns to the zero position(fast/slow).
Sound Unit Menu / MODULATOR
Parameter Remark
SOUND CARRIER
Selection for the BTSC sound carrier
(OFF / ON)
SOUND CARRIER LEVEL
Adjustment of the BTSC sound carrier
level in dB - relative to peak sync of the
vision carrier range.
DEVIATION LIMITER
Selection for the deviation limiter - the
deviation limit is at 120 kHz (OFF / ON)
LIMITER ACTIVE
Indication whether the deviation limiter
has responded or not (YES / NO)
Operator manual
2 - 10 TVS-D 660 LC-Display
Menu Operation
Sound Unit Menu / PRECORRECTION
Parameter Remark
VISION-SOUND CROSSMOD, /
CORRECTOR
Selection for the vision-sound
crossmodulation corrector (OFF / ON) -
reduces distortions and is defined with
the settings below.
DELAY FACTOR
Defines the delay factor for the
vision-sound crossmodulation correction
GAIN FACTOR
Defines the gain factor for the
vision-sound crossmodulation correction
Operator manual
TVS-D 660 LC-Display 2 - 11
Menu Operation
AUDIO SOUND UNIT Menu (FM MONO)
In the SOUND UNIT menu the following parameters are permanently displayed:
Parameter Remark
INPUT
In this specific audio mode two different
inputs are available (MAIN / AUX) on the
front-panel
DEVIATION
Indication of the deviation in kHz
Sound Unit Menu / SWITCH
Parameter Remark
THE AF SOURCE SELECTION
FOLLOWS VIDEO
Depending on the video setting, the
transmitter switches from MAIN sound to
AUX sound and vice versa.
Sound Unit Menu / AF GAIN
Parameter Remark
AF GAIN SND1
Setting of the AF gain for the sound input
in the range of -9.9 ...+6dB
DETECTOR DECAY
Defines the speed at which the indication
bar returns to the zero position(fast/slow).
Operator manual
2 - 12 TVS-D 660 LC-Display
Menu Operation
Operator manual
TVS-D 660 LC-Display 2 - 13
Menu Operation
CONTROL TONE DETECTOR
Activation of the control tone detector at
22.5 kHz (ON/OFF) - for standard I only.
CONTROL TONE PRESENT
Indication of the presence of the control
tone (Smiley / Weepy) - detector has
responded or not.
Sound Unit Menu / PREEMPHASIS
Parameter Remark
PREEMPHASIS
Selection among three values for the
audio preemphasis: OFF,
50 ms, and 75 ms
Sound Unit Menu / MODULATOR
Parameter Remark
SOUND CARRIER 1 Selection for sound carrier 1 (ON / OFF)
SND. CARRIER LEVEL Indication of the sound carrier level in dB
- relative to the peak sync of the vision
carrier
DEVIATION LIMITER (softkey) Selection for the DEVIATION LIMITER
(OFF/60/90/120 kHz) / Indication of the
LIMITER 1 ACTIVE: YES / NO (shows
the status of limiter 1).
Sound Unit Menu / PRECORRECT.
Parameter Remark
VISION-SOUND CROSSMOD. /
CORRECTOR
Selection (OFF / ON)
DELAY FACTOR
Defines the delay factor for the
vision-sound crossmodulation correction
GAIN FACTOR
Defines the gain factor for the
vision-sound crossmodulation correction
DUAL SOUND UNIT Menu
In the SOUND UNIT menu the following parameter is permanently displayed:
Parameter Remark
INPUT
In this specific audio mode two different
inputs are available (MAIN / AUX) on the
front-panel
DEVIATION
Indication of the deviation in kHz
CODER
Shows the actual coding mode
DATALINE
Shows if there is information about the
sound standard in the dataline (Smiley /
Weepy)
TTX
Shows if there is information about the
sound standard in the teletext (Smiley /
Weepy)
Sound Unit Menu / Switch
Parameter Remark
THE AF SOURCE SELECTION
FOLLOWS VIDEO
Depending on the videosetting, the
transmitter switches from MAIN sound to
AUX sound and vice versa.
Operator manual
2 - 14 TVS-D 660 LC-Display
Menu Operation
Sound Unit Menu / AF Gain
Parameter Remark
AF GAIN SND1
Setting of the AF gain for the sound 1
input in the range of -9.9 ...+6dB
AF GAIN SND2
Setting of the AF gain for the sound 2
input in the range of -9.9 ...+6dB
DETECTOR DECAY
Defines the speed at which the indication
bar returns to the zero position(fast/slow).
Sound Unit Menu / Preemphasis
Parameter Remark
PREEMPHASIS
Selection among three values for the
audio preemphasis: OFF,
50 ms, and 75 ms
Sound Unit Menu / Coder Control
Parameter Remark
CTRL - MODE
Selection of the control mode (AUTO /
MAN)
HIGH PRIORITY
Selection of the most prioritiest mode of
coding (DATA / TXT)
MANUAL CODING
Selectioning the kind of the outcoming
signal ( MONO / DUAL / STEREO )
ACTUAL CTRL SOURCE
Indicates the present control source
(MANUAL / DATALINE / TTX (teletext))
Sound Unit Menu / Modulator
Parameter Remark
SOUND CARRIER 1
Selection for sound carrier 1 (ON / OFF)
(sound carrier 5.5 MHz relative to the
vision carrier)
SOUND CARRIER 2
Selection for sound carrier 2 (ON / OFF)
(sound carrier 5.742 MHz relative to the
vision carrier)
SND. CARRIER 1 LEVEL
Indication of the sound carrier 1 level in
dB - relative to the peak sync of the
vision carrier
Operator manual
TVS-D 660 LC-Display 2 - 15
Menu Operation
SND. CARRIER 2 LEVEL
Indication of the sound carrier 2 level in
dB - relative to the peak sync of the
vision carrier
PILOT
Selection for the pilot (ON / OFF)
DEVIATION LIMITER (softkey)
Selection for the DEVIATION LIMITER
(OFF/60/90/120 kHz) Indication of the
LIMITER 1 ACTIVE: YES / NO (shows
the status of limiter 1) and incation of
LIMITER 2 ACTIVE: YES / NO
Sound Unit Menu / Precorrection
Parameter Remark
VISION-SOUND CROSSMOD. /
CORRECTOR
Selection (OFF / ON)
DELAY FACTOR
Defines the delay factor for the
vision-sound crossmodulation correction
GAIN FACTOR
Defines the gain factor for the
vision-sound crossmodulation correction
Operator manual
2 - 16 TVS-D 660 LC-Display
Menu Operation
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
