Minka Group 4774-281 User manual

Brand: Minka Group

Model: 4774-281

Type: User manual

This manual is also suitable for

4774-613

INSTALLATION INSTRUCTIONS FOR FIXTURE #4774

ASSEMBLING THE FIXTURE (FIG. 1)

1. Shut off the power at the fuse box or circuit breaker. If necessary,

remove the existing fixture and its mounting hardware from the ceiling.

2. Carefully remove the new fixture from the carton and check that all

parts are included as shown in the illustration.

3. Thread the fixture loop (A) onto the nipple (B);

4. Install the light bulb (D) (included) in accordance with fixture’s

specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE

RATING!) (NE PAS DEPASSER LA PUISSANCE NOMINALE

MAXIMALE!).

MOUNTING THE FIXTURE (FIG. 2)

5. Thread one end of nipple (S) into the crossbar (P).then place lock

washer (Q) and hex nut (R) over the end of nipple (S) ,then thread hex

nut (R) until snug.

6. Thread the ceiling loop (T) onto the nipple (S) until snug.

7. Take this crossbar assembly and mount to the ceiling outlet box (V)

using outlet box screws (W). The side of crossbar (P) marked “GND”

must face out.

8. Use proper chain pliers to open one end link of the chain and connect

to the fixture loop (A). Then close the link.

9. By measuring, determine the correct number of links needed for the

desired hanging height. Using the chain pliers, disconnect and discard

the remaining chain.

10. Slip the lock collar (Y) and canopy (U) over the chain (X). Allowing

them to rest onto the fixture loop (A).

11. Open the other end link of the chain (X) and connect to ceiling loop

(T). Then close the link.

12. Carefully lace the fixture wires through the chain (X).

13. Feed the fixture wires through the ceiling loop (T) and nipple (S) and

pull tight.

CONNECTING THE WIRES (FIG. 3)

14. At this point, connect the electrical wires as shown in Fig. 3 making

sure that all wire connections are secured. If your outlet box has a

ground wire (green or bare copper), connect the fixture’s ground wire

to it. Otherwise, connect the fixture’s ground wire directly to the

crossbar (P) using the green screw provided.

15. After the wires are connected, tuck them carefully into the ceiling

outlet box. Raise the canopy (U) to the ceiling, then raise the lock

collar (Y) and thread onto the ceiling loop (T) protruding through the

canopy (U).

Your installation is now complete. Return power to the outlet box and test

the fixture.

Fig.3

Fig. 1

Fig. 2

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Set A#A-010

-Crossbar

-Ground Screw

-Mounting screws (2)

Chain # HCH2072-281

Chain #HCH2072-613

Gauge 3.80MM

Notice: It is important to use proper chain pliers

(not included) to OPEN and CLOSE the chain

included with this fixture. Do not open them with

other tools that may twist or stress the chain links.

It is important to use proper chain pliers like the

ones shown in the diagram.

**the above drawing is for reference.**

Note: Illustration (Fig. 1)(Fig.2) on this manual is

for installation purposes only. It may or may not

be identical to the fixture purchased.

Minka Group 4774-281 User manual

Brand: Minka Group

Model: 4774-281

Type: User manual

This manual is also suitable for

4774-613

Download PDF

report

Minka Group 4774-281 User manual

This manual is also suitable for

Minka Group 4774-281 User manual

Related papers

Other documents