LG LRSC26912TT Owner's manual

Brand: LG

Model: LRSC26912TT

Category: Fridges

Type: Owner's manual

website:http'J/www.lgservice.com

LRSC 26915SW

LRSC 26912SW

LRSC 26925SW

LRSC 26923SW

LRSC 26940SW

LRSC 26940TT

LRSC 26941SW

RSC 26941 ST

LRSC 26915TT

LRSC 26912TT

LRSC 26925TT

LRSC 26923TT

LRSC 26940SB

LRSC 26940ST

LRSC 26941SB

RATOR

Introduction

Installation

Operation

Suggestion on

Food Storage

Care and

Maintenance

Table of Contents

Entry

Important Safety Instruction

Identification of Parts

Where to Locate

Door Removal

Door Replacement

Water Pipe Installation

Water Connection Instruction Guide

Operation Instruction Guide

Height Adjustment

Starting

Adjusting the Temperatures and functions

(Dispenser/Automatic Icemaker)

Shelf

Wine Holder (Applicable to some models only)

Egg Bin (Applicable to some models only)

Humidity Control in the Vegetable Compartment

Optichill Temperature Transition Corner

Temperature Change at Optichill

Optichill

Location of Foods

Storing Foods

How to Dismantle Parts

General Information

Cleaning

Troubleshooting

Recommended

Grounding

Method

Accessibility of

Supply Plug

Supply Cord

Replacement

Warning

Entry

The model and serial numbers are found on the inner case or back of refrigerator

compartment of this unit. These numbers are unique to this unit and not

available to others. You should record requested information here and retain

this guide as a permanent record of your purchase. Staple your receipt here.

Date of purchase

Dealer

Dealer address

Dealer phone no.

Model no.

Serial no.

Important safety instruction

BeForeuse, this refrigerator must be properly installed and located in accordance with

the installation instructions in this manual.

Never unplug your refrigerator by pullingon the power cord.Always gripthe plugfirmly

and pull it straight out from the outlet.

When moving your applianceaway Fromthe wall, be careful not to roll over the power

cord or to damage it in any way. Do not crush or damage the water line.

After your refrigerator is in operation, do not touch the cold surfaces in the freezer

compartment, particularlywhen your handsaredamp or wet. Skincould adhere to

these extremely cold surfaces.

Unplugthe power cordFromthe power outlet Forcleaningor other requirements. Never

touch itwith wet handsbecauseyou can get an electric shock or be injured.

Never damage, bend,kink,pull out, or twist the power cord becausedamageto the

power cordcan cause productfailure, fire, or electric shock. If you havedoubts the

applianceis properlygrounded,consult a qualifiedelectrician.

Never placeglass products inthe freezer becausethey may be brokenFromexpansion

when theircontents are frozen.

Never put your handswithin the icestorage bin of the automatic icemaker.You can be

injured bythe operationof the automatic icemaker.

The applianceis not intended Foruse byyoung childrenwithout supervision.

Young children should be supervised to ensure that they do not playwith the appliance.

Never allow anyoneto climb, sit, stand, or hangon the door.These actions may

damagethe refrigeratorand eventip it over, causing severe personalinjury.

Beforeyou moveyourrefrigeratorintoitsfinallocation,

itis importantto makesureyou havethe properelectrical

connection:

A 115Volt,60 Hz.,AConly15,or 20amperefused,grounded

electricalsupplyisrequired.It isrecommendedthata separate

circuitservingonlyyourrefrigeratorbe provided.Useanoutlet that

cannotbe turnedoff bya switch, Donot useanextensioncord,

Therefrigerator-freezershouldbeso positionedthatthe supplyplug

isaccessibleforquickdisconnectioninthe event ofan emergency.

Ifthe supplycordisdamaged,it must bereplacedbythe manufactureror its serviceagentor

asimilarlyqualifiedpersonin orderto avoidanyhazard.

Do not modify or extend the Power Cord length.

• It will cause electric shock or fire.

Child Entrapment

Warning

Don't Store

Grounding (Earthing)

DANGER: Risk of child entrapment.

Beforeyou throw away your old refrigerator or freezer:

Take off the doors but leavethe shelves in placeso that children may not easilyclimb

inside.

The applianceisnot intendedfor use byyoung children without supervision.

Young children should be supervised to ensure that they do not playwith the appliance.

Don't store or use gasolineorother flammable vapor and liquids inthe vicinity of this or

any other appliance.

Inthe event of an electric short circuit, grounding (earthing)reduces the risk of electric

shock by providingan escape wire for the electriccurrent.

Inorder to prevent possibleelectric shock, this appliancemust be grounded.

improper use ofthe grounding plug can result in an electric shock. Consulta qualified

electrician or service person irthe grounding instructions are not completely

understood, or ir you havedoubts on whether the applianceisproperly grounded.

Identification of Parts

DoorRack

Automatic

Icemaker

Lamp

Shelf ........................

(steelor glass)

Jet Freezing

DoorRack ..........................

Drawer .........................

Freezer

Compartment

DoorRack _ -O-

LowerCover .............................................................................

Refrigerator

Compartment

DairyCorner

WaterFilter

............................................Lamp

Shelf

Wineholder

..........................................Shelf

SnackDrawer

..........................................EggBox

--- Lamp

VegetableDrawer

-- DoorRack

Optichill

Select a Good

Location

Where to Locate

1. Placeyour appliance where it is easy to use.

2.Avoid placing the unit near heat sources, direct sunlight, or moisture.

3.To avoid vibrations, the appliance must be leveled.

4. Do not install this refrigerator in areas where the ambient temperature is below 414:.

It will havean adverse effect on performance.

Warning

Remove Lower

Cover and

Water Feed Tube

Remove the

Freezer

Compartment

Door

Remove the

Refrigerator

Door

Door removal

ElectricShock Hazard

Disconnectelectricalsupply to refrigerator beforeinstalling.

Failureto do socouldresult in deathor seriousinjury,

Ifyour entrance door istoo narrow for the

refrigerator to passthrough, remove the

refrigeratordoor and passthe refrigeratorlaterally.

Removethe lowercover byliftingupward,and

then pullupthe water feedtubewhile pressing

area¢ shown inthe figureto the right,

Water Feed Tube

) \ Hinge

. . £ Cover Connection

1)Remove the hinge cover by loosening the /_) .........It _ Wires

screws, Disconnectall connections except _

the groundline, -_ ,_- _//

Upper Hinge I < \ _ EarthLine

2) Removethe keeperbyrotating itcounter -__._/KeeperF UpperHinge

clockwise @andthen liking the upper _-...C>-_'_

hinge up@.

3) Removethe freezercompartmentdoorby

liking it upward,Thistime, thedoor should

be liked enoughforthewater feed tubeto

be completelypulledout,

Lower hinge

_"En0ughforwatei_",,,,

feedpipetubetobe

:ompletelypulled0u!/

1)Loosenthe hingecoverscrews andremove

the cover,Removeconnectionwire, ifany,

exceptforthe groundline.

2) Removekeeperbyrotating it clockwise @

and then removethe upperhingeby lifting

it up @.

Connection

Wires

Upper Hinge _.._[ Keeper

3) Removethe refrigeratorcompartment door

bylifting it up.

Lower Hinge

Move the

Refrigerator

Before

Installation

Push the refrigerator sideways through the

entrance door as shown in the right picture,

Door replacement

Mount the doors inthe reverse order of removal after the refrigerator is broughtto

the installationarea.

Feed water tube installation

• Automatic icemaker operation needs water pressure of 21.3-1 21psi(Ib/inch2)(That

is, a 7oz. paper cup will be filled within 3 sec.).

• If water pressure does not reach the rated 21.3psi(Ib/inch2)or below, it is necessary

to purchase a separate pressure pump for normal automatic icemaking and cool

water feed.

• Keep the total length of the water feed tube within 40 feet and be careful not to

bend or kink the tube. If the tube is longer than 40 feet, the icemaker and water

dispenser will not operate properly.

• Installthe water feed tube at a placefree from heat.

Warning • Connect to potable water supply only.

• Refer to instructions with water filter kit for installation.

Connecting

the Refrigerator

to a Water Source

Warning

Tools Required

Cold Water Supply

Water Connection Instruction Guide

Readall directions carefully before you begin.

Connect to potable water supply only.

• Standard screwdriver

• 7/16-inch and 1/2-inch open-end wrenches or two adjustable wrenches

• 1/4-inch nut driver

• 1/4-inch drill bit

• Hand drill or electric drill (properly grounded)

The icemaker water valve contains a flow washer which is used as a water

pressure regulator.

The icemaker needs to be connected to a cold water line with water pressure

30o-120psi(Ib/inch2)

Connect

the Tubing to

Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn on the nearest faucet to relieve the pressure

on the line. It may help to open an outside faucet to allow the water to drain from

the line in the house.

3. Find a 1/2dnch to 1-1/4-inch vertical COLD water pipe near the refrigerator.

4. To determine the length of copper tubing you will need, measure from the

connection on the lower left rear of the refrigerator to the water pipe. Add 7

feet (2.1m) to allow for moving refrigerator for cleaning. Use 1/4dnch O.D.

(outside diameter) copper tubing. Be sure both ends of copper tubing are cut

square.

5. Using a drill, drill a 1/4dnch hole in the cold water pipe you have selected.

6. Fasten shut-off valve to cold water pipe with pipe clamp. Be sure outlet end is

solidly in the 1/4dnch drilled hole in the water pipe and that the washer is

under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws

carefully and evenly so washer makes a watertight seal. Do not overtighten or

you may crush the copper tubing, especially if soft (coiled) copper tubing is

used. Now you are ready to connect the copper tubing.

7. Slip compression sleeve and compression nut on copper tubing as shown.

Insert end of tubing into outlet end squarely asfar as it will go. Screw

compression nut onto outlet end with adjustable wrench. Do not over tighten.

8. Place the free end of the tubing into a container or sink, and turn ON main

water supply and flush out tubing until water is clear. Turn OFF shutoff valve

on the water pipe. Coil the copper tubing as shown below.

_jjl Cold Water Pipe

Pipe Clamp

Packing Nut\ __/j_

\ _ ih I Coil of Polyethylene or

Shut Off Valve_

Compress'_ Compression Nut _

Connect the Tubing

to the Refrigerator

Turn the Water On at

the Shutoff Valve

Automatic Ice maker

Operation Instruction Guide

Before making the connection to the refrigerator, be sure the refrigerator

power cord is not plugged into the wall outlet.

•If your refrigerator does not

have a water filter, we Tubing_ampf

recommend installing one. If

your water supply has sand or

particles that could clog the

1/4" ssion _,

screen of the refrigerator's compre

water valve. Install the filter in Nut

the water line near the

refrigerator.

Ferrule

1. Remove the plastic flexible

cap from the water valve.

Tighten any connections that leak.

• Plug In the Refrigerator

Arrange the coil of copper tubing behind the refrigerator so it does not vibrate

against the back of the refrigerator or against the wall. Push the refrigerator

back to the wall.

• Start the Icemaker

Set the icemaking stop switch to the ON position The icemaker will not begin

to operate until it reaches its operating temperature of 15 °F (-9 °C). It will then

begin operation automatically if the icemaking stop switch is in the ON

position.

• The automatic icemaker makes 8 cubes at a time, 120/150 pieces per day.

But these quantities may vary according to circumstance, including ambient

temperature, door openings, freezer load.etc.

• The Icemaker stops when the bin is full.

1/4"Tubing

2. Place the compression nut and

ferrule (sleeve) onto the end of RefrigeratorConnection

the tubing as shown.

3. Insert the end of the copper tubing into the connection as far as possible. While

holding the tubing, tighten the fitting.

When Icemaker

Does Not Operate

Smoothly

CAUTION

Ice is clumped together

• When ice is clumped together, take the ice clumps out of the ice storage bin,

break them into small pieces, and then place them into the ice storage bin

again.

• When the icemaker produces too small or clumped ice, the amount or water

supplied to the ice maker must be adjusted. Contact the service center.

• If ice is not used frequently, it may clump together.

Power failure

• Water may drop into the freezer compartment. Take the ice storage bin out and

discard all the ice. Dry the bin and replace it.

The unit is newly installed

• It takes about 12 hours for a newly installed refrigerator to make ice.

Throw away the ice.

The first iceand water may include particles or odor from the reed water pipe or

reed water box.

This is also necessary irthe refrigerator has not been used for a long time.

Never store beverage cans or other roods in ice storage bin for the purpose of rapid

cooling.

Suchactions may damage the automatic ice maker.

Never remove the icemaker cover.

Shakethe bin occasionallyto cause the iceto settle.

Ice may pile upjust around the icemaker causing the icemaker to think that the ice

storage bin isfull.

If discolored ice is dispensed, contact an Authorized Service Center immediately.

Do not use the ice or water until the problem is corrected.

If the freezer

compartment door

is lower than the

refrigerator

compartment door

If the freezer

compartment door

is higher than the

refrigerator

compartment door

After leveling the

door height

Height Adjustment

Levelthe door by insertingflat (- type) driverintothe grooveofthe left heightadjusting

screw and rotating itclockwise O.

Height Difference

iS?"

Left Height

Adjustment Screw

Levelthe door by inserting flat (- type) driver into the groove of the right height

adjusting screw and rotating it clockwise O.

Height Difference

Right Height

Adjustment Screw

The refrigerator doors will close smoothly by adjusting the height adjusting screw. If

the doors do not close correctly, performance may be affected.

1.Wipe off all dust accumulated during shipping and clean your appliance thoroughly.

2. Install accessories such as the ice cube box, cover evaporating tray, etc., in their

proper places.They are packedtogether to prevent possibledamage during shipping.

3. Connect the power supply cord (or plug) to the outlet. Use this appliance on a

dedicated circuit.

Starting

When your refrigerator isfirst installed, allow it to stabilize at normal operating

temperatures for 2-3 hours prior to filling it with fresh orfrozen foods.

If operation is interrupted, wait 5 minutes before restarting.

AdJusting The Temperatures and Functions

Water/Ice Output

Dispenser Push Switch

Dispenser Lamp

_Bottom ceiling of

functlbn dlsplay board)

Functiondisplayboard

EXPRESS/JETFRZDISPENSER

Buzzersound

mute Mode

DisplayPower

savingMode

FREEZERREFRIGERATORFILTER/LIGHTLOOK

ChangeDisplayDegreefrom Fahrenheit

to CentigradeMode

1. Buzzersound mute Mode

The buzzer sound is set to OFF.

It activates by sounding the recognition sound or "Ding-" alter pressing and

holding "Express FRZ" button more than 4 seconds.

It inactivates when resetting the mode power.

2. Display Power saving Mode

It places display in standby mode until door is opened.

Press "Freezer" and "Express FRZ" buttons simultaneously to turn all leds ON and

then OFF with the recognition sound of "Ding-" aRer 5 seconds.

Once the mode activates, the display is OFF.Until door isopened or display button

is pressed. When 30 seconds haselapsed after closing door or pressing button,

the display turns OFF.

To deactivate this mode issame as the activation methods. The mode inactivates

when resetting the power.

3. To change temperature display from Fahrenheit to Celsius press and hold

"FREEZER" and "REFRIGERATOR" buttons simultaneously for more than 5

seconds. Dothe same to convert backto Celsius.

How to adjust the

temperature in

the freezer

compartment

How to adjust the

temperature in

the refrigerator

compartment

Dispenser

selection

You can adjust temperature of freezer compartment and refrigerator

Compartment.

,_eezer Compartment temperature adjustment

FREEZER _e Setting "_ I _

mperature ! °F ! °F 5°F -8°F

• = • = •

BAR . = = =

C_D C_ COLD COLD

_frigerator Compartment temperature adjustment

Setting (..hS.,F #'/ / °F 37F 3t"/°F 3_'_ °F

REFRIGERATOR jemperature

BAR "

Indication " " " _ " _ •

c_.ic. ICL i LI oi

_D _D OD COD COL

_:_Whenever pressing button, setting isrepeated in the order of (Middle) -_

(Middle Strong) ÷ (Strong)÷ (Weak)÷ (Middle Weak).

• The actual inner temperature varies depending on the food status, as the

indicated setting temperature is the target temperature, not actual temperature

within refrigerator.

• Pleaseadjust temperature asabove after using refrigerator for minimum 2-3

days.

You can select water or ice.

_,'I_Pleaseselect water, Crushed ice, or cubed ice by

, DISPEi_SER

pressing d_ button as you desire.

_,_' . .

:_,_Pleasepress the button gently by pushing in cup.

• You will hear a clap when the ice door closes

after ice isdispensed.

• Reference : Hold your cup in place for a couple of seconds after

dispensing ice or water so the last few drips go in

your cup instead of on the floor.

DISPENSER

Pressing

Switch

[

Automatic

Icemaker

When ice maker

does not operate

smoothly

Jet Freezer

Lock

• The automatic icemaker can automatically make 8 cubes at a time,

120-150 pieces per day. This quantity may vary bycircumstance, including ambient

temperature, door opening, freezer load.etc.

• Icemaking stops when the ice storage bin is full.

• If you don't want to use automatic icemaker, turn the icemaker switch to

OFF.

If you want to use automatic ice-makeragain, change the switch to ON.

Ice is lumped together

• If the ice lumps together, take it out, break it apart, and put it back into the storage

bin.

• When the ice maker produces too small or lumped together ice, the amount of

water supplied to the ice maker needs to adjusted. Contact the service center.

¢ If ice is not used frequently, it may lump together.

Power failure

• Ice may drop into the freezer compartment. Take the icestorage bin out and discard

all the icethen dry it and placeit back.After the machine is powered again, crushed

icewill be automatically selected.

The unit is newly installed

• It takes about 12 hours for a newly installed refrigerator to make ice.

Please select this function for prompt freezer,

• "OFF--* EXPRESS--*JET--*OFF" or

"OFF--* ON--*OFF" isrepeated

whenever pressing _x,_2ETF_zbutton.

• The arrow mark graphic remains at the

On status after flickering 4 times when

selecting SpecialRefrigeration On

• Prompt freezer function automatically

turns off after a fixed time passes.

• JET FRZ: Not applicable to all models.

EXPRESS/JETFRZ

Ex) Inselecting Ex) Inselecting Ex) Inselecting

On On Off

This button stops operation of different

button and dispenser function.

• Locking or Release is repeated

whenever the L/_ is pressed more than 3

seconds. _

• If you use the LOCK button, none of the other

buttons will work until you unlock them.

LOCK

Ex) In selecting Ex) Inselecting

LOCK UNLOCK

The Other

Functions

How Ice/Cold

Water is Supplied

How to Use

Dispenser

Ambient Temperature Display Window.

• Temperature is displayedonly between 16W - 12047.

• Temperature less than 15W isindicated with LO and

temperature more than 12147 isindicated with HI.

ROOM TEMP

Door open warning

• A warning tone will sound 3 times atthirty-second intervalsif the refrigerator orfreezer

door isleft open for more than sixty seconds.

• Pleasecontact with the localservicecenter if warning continue to sound evenafter

closing the door.

Diagnosis (failure detection) function

• Diagnosisfunction automaticallydetects failurewhen failure isfound in product during

the use of refrigerator.

• Ifyour refrigeratorfails, do notturn off the power. Instead, contact a localAuthorized

servicecenter or call our support line for assistance.Turning off the appliancewill

make it more difficult for the servicetechnician to determine the problem.

Water is cooled while stored in the water tank in freezer door, and then sent to the

dispenser.

Ice is made in the automatic icemaker and sent to the dispenser divided into crushed

or cubed ice.

• Select among crushed ice, water, and cubed ice and press the push switch with a

glass or other container.

Water

Light the water lamp

by pressing the

selection button.

•Water will be dispensed

by pressing the push

switch with a glass.

_SPENSER

Crushed Ice

Light the crushed ice

lamp by pressing the

selection button.

•Crushed icewillbe

dispensedby pressingthe

pushswitchwith aglass,

Cubed Ice

Light the cubed ice

lamp by pressing

the selection

button.

•Cubedicewillbedispensed

by pressing the push

switch with a glass.

_SPENSER DISPENSER

6 Filter Condition

(filter replacement

cycle) Display

Function

Cautions

LED

• There isa replacement indicator lightfor the Classification

water filter cartridge on the dispenser.

• Water filter needsreplacement onceevery six FmerStatus

months. Display

• Filter lightcomes on to let you know when to

replacefilter.

• ARer replacethe filter, press andhold the lock button more than 3seconds.

FILTERRESET,HOLD 3 SECStext turn off filter light.

Ininitial Power On Replace indicator

/ Filter RESET lighton

Throw away the ice(about 20 pieces)and water (about 7 glasses)first made after

refrigerator installation.

This isalso necessarywhen the refrigerator has not been used for a longtime

Keep childrenaway from the dispenser.

Childrenmay playwith or damagethe controls.

Be careful that food does not block the ice passage.

Iffoods are placed at the entrance of ice passage, the

dispenser may malfunction. The passage may also become

blocked with frost if only crushed ice is used. Remove the

frost that accumulates.

Storing cansor other items in the icebin may damage

the icemaker or the container may burst,

Never usethin crystal glassor crockeryto collectice.

Suchglasses or containers may be broken.

Put icefirst into a glassbefore filling water or other beverages.

Water may be splashed ificeisadded to existing liquidina glass

Keep your handsand toolsout of the icedoor and passage.

You might break something or injure yourself.

Never remove the ice maker cover.

Freezer

Door

Shake the ice binoccasionallyto level the icein it.

Sometimes the ice pilesup nearthe icemaker, causingthe icemaker to misread the bin

leveland stop producingice.

Ifdiscoverediceor water isdispensed,contact an Authorized servicecenter

immediately and discontinue useuntil the problem iscorrected.

Never usetoo narrow or deep glass.

Icemay bejammed in icepassageand,thus, the refrigerator may befailed.

Keep the glassat a properdistance from iceoutlet.

A glass too close to the outlet may hinder ice from coming out.

Shelf Height

Adjustment

Wine Holder

Adjustment

Shelf

The refrigerator compartment shelf is movable so that you can place it at a height

according to space requirement of foods.

Pull out refrigerator tray to the front after

lifting it slightly.

Wine Holder

(Applicable to some models only)

Bottles can be stored on their sides in this

wine rack. It can be mounted only at the

SLIDESHELF.

Move to left to pull out after lifting slightly.

Egg Bin (Applicable to some models only)

You carl placethe egg box wherever you want it.

[Normal] [For Many Eggs]

Humidity control in the vegetable compartment

The humidity carl be controlled by adjusting the humidity control switch to the left

or right when storing vegetabes or fruits.

Highhumidity

I Humidity Control

Higit ,,°,,°, _,,,,°,° Low

Low humidity

Humidity Control

High .°°.°°, I °°.°°,° Low

Page is loading ...

LG LRSC26912TT Owner's manual

Brand: LG

Model: LRSC26912TT

Category: Fridges

Type: Owner's manual

Download PDF

report

LG LRSC26912TT Owner's manual

LG LRSC26912TT Owner's manual

Related papers

Other documents