Genius Falcon User manual

Category
Gate Opener
Type
User manual

This manual is also suitable for

ITALIANO
AVVERTENZE PER L’INSTALLATORE
OBBLIGHI GENERALI PER LA SICUREZZA
ATTENZIONE! È importante per la sicurezza delle persone seguire attentamente
tutta l’istruzione. Una errata installazione o un errato uso del prodotto può
portare a gravi danni alle persone.
Leggere attentamente le istruzioni prima di iniziare l’installazione del prodotto.
I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere lasciati
alla portata dei bambini in quanto potenziali fonti di pericolo.
Conservare le istruzioni per riferimenti futuri.
Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato
in questa documentazione. Qualsiasi altro utilizzo non espressamente indicato po-
trebbe pregiudicare l’integrità del prodotto e/o rappresentare fonte di pericolo.
GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso da
quello per cui l’automatismo è destinato.
Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi
infiammabili costituisce un grave pericolo per la sicurezza.
Gli elementi costruttivi meccanici devono essere in accordo con quanto stabilito
dalle Norme EN 12604 e EN 12605.
Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un livello di
sicurezza adeguato, devono essere seguite le Norme sopra riportate.
GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella costruzione
delle chiusure da motorizzare, nonché delle deformazioni che dovessero intervenire
nell’utilizzo.
L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453 e EN
12445. Il livello di sicurezza dell’automazione deve essere C+D.
Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione elettrica
e scollegare le batterie.
Prevedere sulla rete di alimentazione dell’automazione un interruttore onnipolare
con distanza d’apertura dei contatti uguale o superiore a 3 mm. È consigliabile
l’uso di un magnetotermico da 6A con interruzione onnipolare.
Verificare che a monte dell’impianto vi sia un interruttore differenziale con soglia
da 0,03 A.
Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi le parti
metalliche della chiusura.
L’automazione dispone di una sicurezza intrinseca antischiacciamento costituita
da un controllo di coppia. E’ comunque necessario verificarne la sogli di intervento
secondo quanto previsto dalle Norme indicate al punto 10.
I dispositivi di sicurezza (norma EN 12978) permettono di proteggere eventuali
aree di pericolo da Rischi meccanici di movimento, come ad Es. schiacciamento,
convogliamento, cesoiamento.
Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione luminosa non-
ché di un cartello di segnalazione fissato adeguatamente sulla struttura dell’infisso,
oltre ai dispositivi citati al punto “16”.
GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funzionamento
dell’automazione, in caso vengano utilizzati componenti dell’impianto non di
produzione GENIUS.
Per la manutenzione utilizzare esclusivamente parti originali GENIUS.
Non eseguire alcuna modifica sui componenti facenti parte del sistema d’auto-
mazione.
L’installatore deve fornire tutte le informazioni relative al funzionamento manuale
del sistema in caso di emergenza e consegnare all’Utente utilizzatore dell’impianto
il libretto d’avvertenze allegato al prodotto.
Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto du-
rante il funzionamento.
Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore di
impulso, per evitare che l’automazione possa essere azionata involontariamente.
Il transito tra le ante deve avvenire solo a cancello completamente aperto.
L’utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o d’intervento
e deve rivolgersi solo ed esclusivamente a personale qualificato GENIUS o centri
d’assistenza GENIUS.
Tutto quello che non è previsto espressamente in queste istruzioni non è permes-
so.
ENGLISH
IMPORTANT NOTICE FOR THE INSTALLER
GENERAL SAFETY REGULATIONS
ATTENTION! To ensure the safety of people, it is important that you read all the
following instructions. Incorrect installation or incorrect use of the product
could cause serious harm to people.
Carefully read the instructions before beginning to install the product.
Do not leave packing materials (plastic, polystyrene, etc.) within reach of children
as such materials are potential sources of danger.
Store these instructions for future reference.
This product was designed and built strictly for the use indicated in this documen-
tation. Any other use, not expressly indicated here, could compromise the good
condition/operation of the product and/or be a source of danger.
GENIUS declines all liability caused by improper use or use other than that for which
the automated system was intended.
Do not install the equipment in an explosive atmosphere: the presence of inflam-
mable gas or fumes is a serious danger to safety.
The mechanical parts must conform to the provisions of Standards EN 12604 and
EN 12605.
For non-EU countries, to obtain an adequate level of safety, the Standards mentioned
above must be observed, in addition to national legal regulations.
GENIUS is not responsible for failure to observe Good Technique in the construction
of the closing elements to be motorised, or for any deformation that may occur
during use.
The installation must conform to Standards EN 12453 and EN 12445. The safety level
of the automated system must be C+D.
Before attempting any job on the system, cut out electrical power and disconnect
the batteries.
The mains power supply of the automated system must be fitted with an all-pole
switch with contact opening distance of 3mm or greater. Use of a 6A thermal breaker
with all-pole circuit break is recommended.
Make sure that a differential switch with threshold of 0.03 A is fitted upstream of
the system.
Make sure that the earthing system is perfectly constructed, and connect metal
parts of the means of the closure to it.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
The automated system is supplied with an intrinsic anti-crushing safety device con-
sisting of a torque control. Nevertheless, its tripping threshold must be checked as
specified in the Standards indicated at point 10.
The safety devices (EN 12978 standard) protect any danger areas against mecha-
nical movement Risks, such as crushing, dragging, and shearing.
Use of at least one indicator-light is recommended for every system, as well as a
warning sign adequately secured to the frame structure, in addition to the devices
mentioned at point “16”.
GENIUS declines all liability as concerns safety and efficient operation of the auto-
mated system, if system components not produced by GENIUS are used.
For maintenance, strictly use original parts by GENIUS.
Do not in any way modify the components of the automated system.
The installer shall supply all information concerning manual operation of the system
in case of an emergency, and shall hand over to the user the warnings handbook
supplied with the product.
Do not allow children or adults to stay near the product while it is operating.
Keep remote controls or other pulse generators away from children, to prevent the
automated system from being activated involuntarily.
Transit through the leaves is allowed only when the gate is fully open.
The User must not in any way attempt to repair or to take direct action and must
solely contact qualified GENIUS personnel or GENIUS service centres.
Anything not expressly specified in these instructions is not permitted.
FRANÇAIS
CONSIGNES POUR L’INSTALLATEUR
RÈGLES DE SÉCURITÉ
ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la lettre
toutes les instructions. Une installation erronée ou un usage erroné du produit
peut entraîner de graves conséquences pour les personnes.
Lire attentivement les instructions avant d’installer le produit.
Les matériaux d’emballage (matière plastique, polystyrène, etc.) ne doivent pas
être laissés à la portée des enfants car ils constituent des sources potentielles de
danger.
Conserver les instructions pour les références futures.
Ce produit a été conçu et construit exclusivement pour l’usage indiqué dans cette
documentation. Toute autre utilisation non expressément indiquée pourrait compro-
mettre l’intégrité du produit et/ou représenter une source de danger.
GENIUS décline toute responsabilité qui dériverait d’usage impropre ou différent de
celui auquel l’automatisme est destiné.
Ne pas installer l’appareil dans une atmosphère explosive: la présence de gaz ou
de fumées inflammables constitue un grave danger pour la sécurité.
Les composants mécaniques doivent répondre aux prescriptions des Normes EN
12604 et EN 12605.
Pour les Pays extra-CEE, l’obtention d’un niveau de sécurité approprié exige non
seulement le respect des normes nationales, mais également le respect des Normes
susmentionnées.
GENIUS n’est pas responsable du non-respect de la Bonne Technique dans la con-
struction des fermetures à motoriser, ni des déformations qui pourraient intervenir
lors de l’utilisation.
L’installation doit être effectuée conformément aux Normes EN 12453 et EN 12445.
Le niveau de sécurité de l’automatisme doit être C+D.
Couper l’alimentation électrique et déconnecter la batterie avant toute interven-
tion sur l’installation.
Prévoir, sur le secteur d’alimentation de l’automatisme, un interrupteur omnipolaire
avec une distance d’ouverture des contacts égale ou supérieure à 3 mm. On re-
commande d’utiliser un magnétothermique de 6A avec interruption omnipolaire.
Vérifier qu’il y ait, en amont de l’installation, un interrupteur différentiel avec un
seuil de 0,03 A.
Vérifier que la mise à terre est réalisée selon les règles de l’art et y connecter les
pièces métalliques de la fermeture.
L’automatisme dispose d’une sécurité intrinsèque anti-écrasement, formée d’un
contrôle du couple. Il est toutefois nécessaire d’en vérifier le seuil d’intervention
suivant les prescriptions des Normes indiquées au point 10.
Les dispositifs de sécurité (norme EN 12978) permettent de protéger des zones éven-
tuellement dangereuses contre les Risques mécaniques du mouvement, comme
l’écrasement, l’acheminement, le cisaillement.
On recommande que toute installation soit doté au moins d’une signalisation lumi-
neuse, d’un panneau de signalisation fixé, de manière appropriée, sur la structure
de la fermeture, ainsi que des dispositifs cités au point “16”.
GENIUS décline toute responsabilité quant à la sécurité et au bon fonctionnement
de l’automatisme si les composants utilisés dans l’installation n’appartiennent pas
à la production GENIUS.
Utiliser exclusivement, pour l’entretien, des pièces GENIUS originales.
Ne jamais modifier les composants faisant partie du système d’automatisme.
L’installateur doit fournir toutes les informations relatives au fonctionnement manuel
du système en cas d’urgence et remettre à l’Usager qui utilise l’installation les “In-
structions pour l’Usager” fournies avec le produit.
Interdire aux enfants ou aux tiers de stationner près du produit durant le fonction-
nement.
Eloigner de la portée des enfants les radiocommandes ou tout autre générateur
d’impulsions, pour éviter tout actionnement involontaire de l’automatisme.
Le transit entre les vantaux ne doit avoir lieu que lorsque le portail est complète-
ment ouvert.
L’utilisateur doit s’abstenir de toute tentative de réparation ou d’intervention et
doit s’adresser uniquement et exclusivement au personnel qualifié GENIUS ou aux
centres d’assistance GENIUS.
Tout ce qui n’est pas prévu expressément dans ces instructions est interdit.
ESPAÑOL
ADVERTENCIAS PARA EL INSTALADOR
REGLAS GENERALES PARA LA SEGURIDAD
ATENCION! Es sumamente importante para la seguridad de las personas seguir
atentamente las presentes instrucciones. Una instalación incorrecta o un uso
impropio del producto puede causar graves daños a las personas.
Lean detenidamente las instrucciones antes de instalar el producto.
Los materiales del embalaje (plástico, poliestireno, etc.) no deben dejarse al alcance
de los niños, ya que constituyen fuentes potenciales de peligro.
Guarden las instrucciones para futuras consultas.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
1.
2.
3.
6
ENGLISH
Notes on reading the instruction
Read this installation manual to the full before you begin installing the product.
The symbol indicates notes that are important for the safety of persons and for the good condition of the automated system
The symbol draws your attention to the notes on the characteristics and operation of the product.
CE DECLARATION OF CONFORMITY
Manufacturer: GENIUS S.p.A.
Address: Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALY
Declares that: Operator mod. FALCON M
• is built to be incorporated in a machine or to be assembled with other machinery to create a machine under the provisions of Directive 98/37/EC;
• conforms to the essential safety requirements of the other following EEC directives:
73/23/EEC and subsequent amendment 93/68/EEC.
89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC
Furthermore, the manufacturer declares that the machinery must not be put into service until the machine into which it will be incorporated or of which
it will become a part has been identified and its conformity to the conditions of Directive 98/37/EC has been declared.
Grassobbio, 05-12-2006
Managing Director
D. Gianantoni
INDEX
1. DESCRIPTION AND TECHNICAL SPECIFICATIONS page.7
2. DIMENSIONS page.7
3. MAXIMUM USE CURVE page.7
4. ELECTRONIC DEVICES (standard system) page.7
5. INSTALLING THE AUTOMATED SYSTEM page.8
5.1. PRELIMINARY CHECKS page.8
5.2. MASONRY FOR FOUNDATION PLATE page.8
5.3. MECHANICAL INSTALLATION page.8
5.4. INSTALLING THE RACK page.8
6. START-UP page.9
6.1. CONNECTION OF CONTROL BOARD page.9
6.2. POSITIONING THE TRAVEL-LIMIT ELEMENTS page.9
7. AUTOMATED SYSTEM TEST page.10
8. MANUAL OPERATION page.10
9. RESTORING NORMAL OPERATION MODE page.10
10. SPECIAL APPLICATIONS page.10
11. MAINTENANCE page.10
12. REPAIRS page.10
13. ACCESSORIES page.10
7
ENGLISH
FALCON M AUTOMATED SYSTEM
These instructions apply to the following models:
FALCON 14 M - FALCON 14 MC - FALCON 20 M- FALCON 20 MC - FALCON
15 M - FALCON 15 MC - FALCON 20 M 3PH
The FALCON gearmotor for sliding gates is an electro-mechanical operator
which transmits drive to the sliding leaf by a rack and pinion or by a chain
suitably coupled to the gate.
The non-reversing system guarantees mechanical locking of the gate
when the motor is not operating and, therefore, there is no need to install
any lock.
The gearmotor does not have a mechanical clutch and, therefore,
requires a control unit with an adjustable electronic clutch which
guarantees the necessary anti-crushing safety.
A handy manual release with a customised key makes the gate manoeu-
vrable in case of a power cut or trouble.
In the Cversion gearmotors, the electronic control unit is housed inside
the operator.
The FALCON gearmotor was designed and built for controlling vehicle
access. Do not use in any different way.
1. DESCRIPTION AND TECHNICAL SPECIFICATIONS
MODEL
5 M
5 MC
8 M
8 MC
424 M
424 MC
Power supply (+6% -10%)
230 V~
50 Hz
115 V~
60 Hz
230 V~
50 Hz
115 V~
60 Hz
230 V~
50 Hz
115 V~
60 Hz
Absorbed power (W) 350 500 600 70
Absorbed current (A) 1.5 3 2.2 5.2 3
Thrust capacitor (µF) 10 30 12.5 50 /
Thrust on pinion (daN) 45 65 40
Torque (Nm) 18 24 13.5
Temperature protection (°C) 140 /
Max leaf weight (Kg) 500 800 400
Type of pinion gear Z 16 module 4
Gate speed (m/min) 12 14 12 14 12
Max. gate length (m) 15
Type of travel-limit device Magnetic
Type of clutch
Electronic torque control
(See control unit)
Use frequency (see graph) S3 - 30% S3 - 40% 100%
Operating ambient tempe-
rature (°C)
-20 ÷ +55
Weight of gearmotor (Kg)
9
(10 Falcon
5MC)
10
(11 Falcon
8MC)
7.5
(8.5 Falcon
424MC)
Protection class IP 44
Operator dimensions See fig. 2
2. DIMENSIONS
3. MAXIMUM USE CURVE
The curve makes it possible to
establish maximum work time (T)
according to use frequency (F).
With reference to standard IEC
34-1, the FALCON gearmotor, with
service type S3, can operate at
use frequency of 40%.
To ensure efficient operation,
operate in the work range under
the curve.
Important: The curve is
obtained at a temperature
of 20°C. Exposure to the
direct sun rays can reduce
use frequency down to
20%.
Calculation of use frequency
The percentage of effective work time (opening + closing) compared to
total time of cycle (opening + closing + pause times).
Calculation formula:
Ta + Tc
% F = X 100
Ta + Tc + Tp + Ti
where:
Ta = opening time
Tc = closing time
Tp = pause time
Ti = interval time between one complete cycle and another
4. ELECTRONIC DEVICES (standard system)
Covering housing
Gearmotor
Release knob with key
Pinion
Sensor cover plug
Magnetic sensor
Securing plate with nuts and wall anchors
Magnetic counter-plates
Tube wrench
Toroidal transformer (for Falcon 424 C only)
Encoder (for Falcon 424 C only)
Control unit with support (for versions C
only)
Pos. Description Connection cable
Gearmotor 3x2.5 mm
2
(230/115V~)
Photocell transmitter 2x0.5 mm
2
(TX)
Photocell receiver 4x0.5 mm
2
(RX)
Key-operated selector switch 2x0.5 mm
2
Flashing light 2x1.5 mm
2
External receiver (optional) 3x0.5 mm
2
Fig. 1
Fig. 2
Fig. 3
8
ENGLISH
5. INSTALLING THE AUTOMATED SYSTEM
5.1. PRELIMINARY CHECKS
To ensure safety and an efficiently operating automatic system, make sure
the following conditions are observed:
• The structure of the door must be suitable to be automated. Specifically,
the wheel diameter must be in relation to the weight of the gate to be
automated; an upper guide must be present; travel-limit mechanical
stops must be fitted to prevent the gate derailing.
• The soil must permit sufficient stability for the foundation plinth.
There must be no pipes or electrical cables in the plinth excavation
area.
If the gearmotor is exposed to passing vehicles, install, if possible, adequate
means of protection against accidental impact.
Check if an efficient earth socket is available for connecting the gear-
motor.
Make sure that there is sufficient space around the operator to enable all
the installation jobs and subsequent maintenance work to be smoothly
carried out.
5.2. MASONRY FOR FOUNDATION PLATE
1. Assemble the foundation plate as
in Fig. 4.
2. The foundation plate must be
located as shown in Fig. 5 (right
closing) or Fig. 6 (left closing) to
ensure correct meshing between
rack and pinion.
The arrow on the foundation plate
must always point to the gate,
see Figs. 05-06.
3. Make a foundation plinth as in Fig. 7 and
wall the foundation plate, providing one
or more sheaths for routing the electri-
cal cables. Using a spirit level, check if
the plate is perfectly level. Wait for the
cement to set.
4. Prepare the electrical cables for connec-
tion to the accessories and the electrical
power supply as shown in Fig. 3.
To facilitate making the connections,
make the cables come out by
about 40 cm from the foundation
plate hole (Fig. 5-6 ref. ).
5.3. MECHANICAL INSTALLATION
Withdraw the protective housing, pulling it up, Fig. 8.
Place the operator on the plate, using the supplied washers and nuts as
shown in Fig. 9, and the supplied tube wrench (Fig. 9 ref. ).
During this operation, route the cables through the slot on the
operator’s reduction element .
Adjust the height of the gearmotor and the distance from the gate,
referring to dimensions in Fig. 10.
This operation is necessary to secure the rack correctly and to enable
you, in future, to make any height adjustments to the motor.
Tighten the gearmotor securing screws.
Prepare the operator for manual operation as described in chapter 8.
5.4. INSTALLING THE RACK
5.4.1. STEEL RACK TO BE WELDED (FIG.11)
Fit the three threaded pawls on the rack
element, positioning them on the upper
part of the slot. In this way the clearance
on the slot will enable any adjustments
long-term.
Manually move the leaf to its opening
position.
Lay the first piece of rack level on the pinion
and weld the threaded pawl on the gate
as shown in Fig.13.
Manually move the gate, checking if the
rack is resting on the pinion and weld the second and third pawls.
Fit another rack element next to the previous one, using a piece of rack,
as shown in Fig.14 ref. , to synchronise the teeth of the two elements.
Move the gate manually and weld the three threaded pawls. Carry on
like this until you have fully covered the gate.
Do not allow any superfluous sections of rack to project from the
gate.
5.4.2. STEEL RACK TO BE SCREWED (F
IG. 12)
Manually move the leaf to its opening
position.
Rest the first section of rack on the pin-
ion, positioning the spacer between the
rack and the edge of the gate. Using
a spirit level, check if the rack is horizontal
and mark the perforation point with a felt-
tipped pen.
Drill with a 6.5 mm diameter bit, and thread
with an M8 male element. Screw the bolt.
Manually move the gate, checking if the
rack is resting on the pinion and repeat the operations in point .
Fit another rack element next to the previous one, using a piece of rack, as
shown in Fig. 14 ref. , to synchronise the teeth of the two elements.
Move the gate by hand and perform the securing operations as for
the first element, carrying on like this until you have covered the gate
completely.
Do not allow any superfluous sections of rack to project from the
gate.
Fig. 8
Fig. 5 Fig. 6
Fig. 7
Fig. 4
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
9
ENGLISH
Notes on installing the rack
• Make sure that, during gate travel,
all the rack elements do not come
out of the pinion.
• Do not, on any account, weld the
rack elements either to the spac-
ers or to each other.
After you have finished installing the
rack, to ensure correct meshing
with the pinion, we advise you to
lower the position of the gearmo-
tor by about 1.5 mm (Fig.15).
Manually check if the gate correctly
reaches the travel-limit mechani-
cal stops and if there is any friction
during travel.
Do not use grease or other lubri-
cants between rack and pinion.
6. START-UP
6.1. CONNECTION OF CONTROL BOARD
Before attempting any work on the board (connections, program-
ming, maintenance), always turn off power.
Observe points 10, 11, 12, 13 and 14 of the GENERAL SAFETY RULES.
Follow the instructions in Fig. 3, route the cables in the raceways and make
the electrical connections to the selected accessories.
Always separate power cables from control and safety cables (push-but-
ton, receiver, photocells, etc.). To prevent any electric noise whatever, use
separate sheaths.
6.1.1. EARTHING
Connect the earthing cable as shown in Fig. 16.
6.1.2. CONTROL UNIT
In the “Cversion gearmotors, the electronic control unit is secured to an
adjustable support with a transparent cover.
The board programming push-buttons are located on the cover - this enables
you to program the board without having to remove the cover.
To connect the control unit correctly, follow the specific instructions.
6.1.3. CONNECTION OF POWER CABLE
(
FOR FALCON 424C ONLY)
The FALCON 424C gearmotor
houses a screw terminal with fuse-
holder (Fig 17) connected to the
primary circuit of the toroidal tran-
sformer. The mains power cable
230 / 115 V ~ must be connected to
this terminal, respecting what was
specified in Fig. 17. If you have to
replace the fuse, use a fuse type
T1.6A/250V - 5x20 for a 230V power
supply and type T3.15A/250V - 5x20
for a 115V power supply.
6.2. POSITIONING THE TRAVEL-LIMIT ELEMENTS
To correctly position the travel-limit magnets, the control unit must
first be installed and correctly connected to all the command and
safety accessories.
The operator has a magnetic limit switch, which commands gate motion
to stop when the magnet, which is secured to the upper part of the rack,
activates the sensor. The magnets supplied with the operator are specifically
polarised and activate only one of the sensor’s contacts: the closing or
opening contact. The magnet activating the open gate contact bears an
open padlock symbol, and, vice versa, the magnet activating the closed
gate contact bears the closed padlock symbol (see Fig. 18).
Procedure for correct positioning of the two travel-limit magnets:
T
To ensure the operator functions correctly, the magnet showing an
open padlock must be positioned on the left of the operator, looking
at the automated system from the inside. Vice versa, the magnet
showing a closed padlock must be positioned on the right of the
operator.
Assemble the two magnets as shown in Fig. 18.
Set the operator to manual mode operation - as per paragraph 8 - and
power up the system.
Manually take the gate to opening position, leaving 4 cm from the travel
limit mechanical stop.
Slide the magnet nearest to the operator on the rack, in the direction of
the motor - see figure 19. As soon as the LED on the board, referring to
the travel limit stop, goes OFF, take the magnet forward by another 10
mm and fasten it with the appropriate screws (Fig. 19 ref. ).
Do likewise for the other magnet.
Take the gate to about halfway of its travel and relock the system (see
paragraph 9).
Before sending a pulse, make sure that the gate cannot be moved
manually.
Command a complete gate cycle to check if the travel-limit device is
tripping correctly.
To avoid damaging the operator and/or interrupting operation of
the automated system, leave a distance of least 40 mm from the
Fig. 15
Fig. 16
Fig. 18
Fig. 19
Fig. 17
Fig. 14
10
ENGLISH
travel limit mechanical stops.
Make sure that at the end of both the opening and closing manoeu-
vre, the relevant travel-limit LED stays active (LED OFF).
Make the appropriate modifications to the positions of the travel-limit
magnets.
7. AUTOMATED SYSTEM TEST
After installing the operator, carefully check operating efficiency of all
accessories and safety devices connected to it.
Return the board support to its original position. Fit the cover, Fig. 20, and
tighten the two side screws provided, Fig. 20 ref .
Apply the danger sticker on the top of the cover (Fig. 21).
Hand the “User’s Guide” to the Customer and explain correct operation
and use of the gearmotor, indicating the potentially dangerous areas of
the automated system.
8. MANUAL OPERATION
The manual release is a device that makes it possible to disconnect
the operator from the gate, thus enabling manual movement.
Before using the release device, cut power to the system, with the
differential switch upstream of the gearmotor.
THE RELEASE DEVICE MUST NOT BE CONSIDERED AN EMERGENCY STOP
If the gate has to be moved manually due to a power cut or fault of the
automated system, use the release device as follows:
1. Fit the supplied key in the lock, Fig. 22 Ref. , and turn it clockwise as
shown in Fig. 22 Ref. .
2.
Turn the release system clockwise by about 180°, as shown in Fig. 22 Ref. .
3. Open and close the gate manually.
9. RESTORING NORMAL OPERATION MODE
To prevent an involuntary pulse from activating the gate during the
manoeuvre, cut power to the system before re-locking the opera-
tor.
1. Turn the release system anti-clockwise by about 180°, as shown in Fig.
23 ref. .
2. Turn the key anti-clockwise, Fig. 23 ref. , and remove it from the lock, as
shown in Fig. 23 ref. .
3. Move the gate until it meshes to release.
Before powering up the system again, make sure that the gate cannot
be moved manually.
10. SPECIAL APPLICATIONS
There are no special applications.
Anything not expressly specified in these instructions is expressly
prohibited
11. MAINTENANCE
To ensure correct long-term operation and a constant level of safety, we
advise you to generally control the system every 6 months. In the “Use Instruc-
tions” booklet, there is a form for recording maintenance jobs.
The enclosed maintenance form is purely a guideline; it cannot be ruled
out that to guarantee a correctly operating automated system and
a constant level of safety, maintenance operations not described
in this form may be necessary.
12. REPAIRS
The User must not in any way attempt to repair or to take direct action and
must solely contact qualified GENIUS personnel or GENIUS service centres.
13. ACCESSORIES
For accessories, see the GENIUS catalogue.
Fig. 22
Fig. 23
Fig. 20 Fig. 21
11
FRANÇAIS
Remarques pour la lecture de l’instruction
Lire ce manuel d’installation dans son ensemble avant de commencer l’installation du produit.
Le symbole souligne des remarques importantes pour la sécurité des personnes et le parfait état de l’automatisme.
Le symbole attire l’attention sur des remarques concernant les caractéristiques ou le fonctionnement du produit.
DÉCLARATION CE DE CONFORMITÉ
Fabricant: GENIUS S.p.A.
Adresse: Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALIE
Déclare que: L’opérateur mod. FALCON M
• est construit pour être incorporé à une machine ou pour être assemblé à d’autres machines afin de constituer une machine conforme à la Directive
98/37/CE;
• est conforme aux exigences essentielles de sécurité des directives CEE suivantes:
73/23/CEE et modification 93/68/CEE successive.
89/336/CEE et modifications 92/31/CEE et 93/68/CEE successives
On déclare en outre que la mise en service de la machine est interdite tant que la machine à laquelle elle sera incorporée ou dont elle deviendra un
composant n’a pas été identifiée et déclarée conforme aux conditions de la Directive 98/37/CE.
Grassobbio, le 05-12-2006
L’Administrateur Délégué
D. Gianantoni
INDEX
1. DESCRIPTION ET CARACTÉRISTIQUES TECHNIQUES page.12
2. DIMENSIONS page.12
3. COURBE D’UTILISATION MAXIMUM page.12
4. DISPOSITIONS ÉLECTRIQUES (installation standard) page.12
5. INSTALLATION DE L’AUTOMATISME page.13
5.1. VÉRIFICATIONS PRÉLIMINAIRES page.13
5.2. SCELLAGE DE LA PLAQUE DE FONDATION page.13
5.3. INSTALLATION MÉCANIQUE page.13
5.4. MONTAGE DE LA CRÉMAILLÈRE page.13
6. MISE EN FONCTION page.14
6.1. CONNEXION DE LA PLATINE ÉLECTRONIQUE page.14
6.2. POSITIONNEMENT DES FINS DE COURSE page.14
7. ESSAI DE L’AUTOMATISME page.15
8. FONCTIONNEMENT MANUEL page.15
9. RÉTABLISSEMENT DU FONCTIONNEMET NORMAL page.15
10. APPLICATIONS SPÉCIALES page.15
11. ENTRETIEN page.15
12. RÉPARATIONS page.15
13. ACCESSOIRES page.15
2
ENGLISH
Read the instructions carefully before using the product and store
them for future use
GENERAL SAFETY REGULATIONS
If correctly installed and used, the FALCON M automated system
will ensure a high degree of safety. Some simple rules on beha-
viour can prevent accidental trouble:
- Do not stand near the automatic system, and do not allow children,
persons or things to do so, especially when it is operating.
- Keep radio-controls, or any other pulse generators that could involunta-
rily activate the automated system, well away from children.
- Do not allow children to play with the automated system.
- Do not willingly obstruct gate movement.
- Prevent any branches or shrubs from interfering with gate movement.
- Keep the indicator-lights efficient and easy to see.
- Do not attempt to activate the gate by hand unless you have released
it.
- In the event of malfunctions, release the gate to allow access and wait
for qualified technical personnel to do the necessary work.
- When you have set manual operation mode, cut power to the system
before restoring normal operation.
- Do not in any way modify the components of the automated system.
- Do not attempt any kind of repair or direct action whatever and con-
tact qualified personnel only.
- At least every six months: arrange a check by qualified personnel of the
automatic system, safety devices and earth connection.
DESCRIPTION
The FALCON M automated system is ideal for controlling vehicle access
areas in residential environments.
FALCON M for sliding gates is an electro-mechanical operator which
transmits motion to the leaf via a rack and pinion.
For details on sliding gate behaviour in different function logics, consult
the installation Technician.
Automated systems include obstacle detection devices (photocells) that
prevent the gate from closing when there is an obstacle in the area
they protect.
The system ensures mechanical locking when the motor is not operating
and, therefore, installing a lock is unnecessary.
Manual opening is, therefore, only possible by using the release system.
The gearmotor has an adjustable electronic clutch enabling safe use of
the automated system.
The control unit is built into the gearmotor.
A handy manual release facility makes it possible to move the gate in the
event of a power cut or fault.
The warning-light indicates that the gate is currently moving.
TECHNICAL SPECIFICATIONS
MODEL
5 M
5 MC
8 M
8 MC
424 M
424 MC
Power supply (+6% -10%)
230 V~
50 Hz
115 V~
60 Hz
230 V~
50 Hz
115 V~
60 Hz
230 V~
50 Hz
115 V~
60 Hz
Absorbed power (W) 350 500 600 70
Absorbed current (A) 1.5 3 2.2 5.2 3
Thrust capacitor (µF) 10 30 12.5 50 /
Thrust on pinion (daN) 45 65 40
Torque (Nm) 18 24 13.5
Temperature protection (°C) 140 /
Max leaf weight (Kg) 500 800 400
Type of pinion gear Z 16 module 4
MODEL
5 M
5 MC
8 M
8 MC
424 M
424 MC
Gate speed (m/min) 12 14 12 14 12
Max. gate length (m) 15
Type of travel-limit device Magnetic
Type of clutch
Electronic torque control
(See control unit)
Use frequency (see graph) S3 - 30% S3 - 40% 100%
Operating ambient tempe-
rature (°C)
-20 ÷ +55
Weight of gearmotor (Kg)
9
(10 Falcon
5MC)
10
(11 Falcon
8MC)
7.5
(8.5 Falcon
424MC)
Protection class IP 44
Operator dimensions See fig. 2
MANUAL OPERATION
The manual release is a device that makes it possible to disconnect
the operator from the gate, thus enabling manual movement.
Before using the release device, cut power to the system, with the
differential switch upstream of the gearmotor.
THE RELEASE DEVICE MUST NOT BE CONSIDERED AN EMERGENCY STOP
If the gate has to be moved manually due to a power cut or fault of the
automated system, use the release device as follows:
1. Fit the supplied key in the lock, Fig. 1 Ref. a, and turn it clockwise as
shown in Fig. 1 Ref. b.
2. Turn the release system clockwise by about 180°, as shown in Fig. 1 Ref.
c.
3. Open and close the gate manually.
RESTORING NORMAL OPERATION MODE
To prevent an involuntary pulse from activating the gate during
the manoeuvre, cut power to the system before re-locking the
operator.
1. Turn the release system anti-clockwise by about 180°, as shown in Fig.
2 ref. a.
2. Turn the key anti-clockwise, Fig. 2 ref. b, and remove it from the lock, as
shown in Fig. 2 ref. c.
3. Move the gate until it meshes to release.
Before powering up the system again, make sure that the gate can-
not be moved manually.
MAINTENANCE
To ensure correct long-term operation and a constant level of safety, we
advise you to generally control the system every 6 months. In the “Use
Instructions” booklet, there is a form for recording maintenance jobs.
The enclosed maintenance form is purely a guideline; it cannot be
ruled out that to guarantee a correctly operating automated sy-
stem and a constant level of safety, maintenance operations not
described in this form may be necessary.
REPAIRS
The User must not in any way attempt to repair or to take direct action
and must solely contact qualified GENIUS personnel or GENIUS service
centres.
FRANÇAIS
Lire attentivement les instructions avant d’utiliser le produit et les
conserver pour toute nécessité future éventuelle
PRESCRIPTIONS GÉNÉRALES DE SÉCURITÉ
S’il est correctement installé et utilisé, l’automatisme FALCON M
garantit un haut niveau de sécurité. Par ailleurs, quelques règles
simples de comportement peuvent éviter bien des accidents
- Ne pas stationner et interdire aux enfants, aux personnes et aux cho
-
ses
de stationner près de l’automatisme et en particulier durant le
fonctionnement.
- Éloigner de la portée des enfants les radiocommandes ou tout autre
dispositif générateur d’impulsion, pour éviter que l’automatisme ne
soit actionné involontairement.
- Interdire aux enfants de jouer avec l’automatisme.
- Ne pas contraster volontairement le mouvement du portail.
- Éviter que des branches ou des arbustes n’entravent le mouvement
du
portail.
- Faire en sorte que les systèmes de signalisation lumineuse soient
toujours
efficients et bien visibles.
- N’actionner manuellement le portail qu’après l’avoir déverrouillé.
- En cas de dysfonctionnement, déverrouiller le portail pour permettre
l’accès et attendre l’intervention technique du personnel qualifié.
- Lorsque le fonctionnement manuel a été disposé, couper le courant
sur
l’installation avant de rétablir le fonctionnement normal.
- N’effectuer aucune modification sur les composants qui font partie
du
système d’automation.
- Éviter toute tentative de réparation ou d’intervention directe et
s’adresser
uniquement à du personnel qualifié.
- Faire vérifier, au moins tous les six mois, l’efficience de l’automatisme,
des
dispositifs de sécurité et de la mise à la terre par du personnel quali-
fié.
DESCRIPTION
L’automatisme FALCON M est l’idéal pour le contrôle des zones d’ac-
cès de véhicules dans un cadre domestique.
FALCON M pour portails coulissants est un opérateur électromécanique
qui transmet le mouvement au vantail par l’intermédiaire d’un pignon
à crémaillère.
26
NEDERLANDS
Opmerkingen voor het lezen van de instructies
Lees deze installatiehandleiding aandachtig door alvorens te beginnen met de installatie van het product.
Het symbool is een aanduiding voor belangrijke opmerkingen voor de veiligheid van personen en om het automatische systeem in goede staat te
houden.
Het symbool vestigt de aandacht op opmerkingen over de eigenschappen of de werking van het product.
EG-VERKLARING VAN OVEREENSTEMMING
Fabrikant: GENIUS S.p.A.
Adres: Via Padre Elzi, 32 - 24050 - Grassobbio - Bergamo - ITALIE
Verklaart dat: De aandrijving mod. FALCON M
is vervaardigd om te worden ingebouwd in een machine of om te worden geassembleerd met andere machines om een machine te vormen in de
zin van Richtlijn 98/37/EG;
• in overeenstemming is met de fundamentele veiligheidseisen van de volgende EEG-richtlijnen:
73/23/EEG en latere wijziging 93/68/EEG.
89/336/EEG en latere wijzigingen 92/31/EEG en 93/68/EEG
daarnaast verklaart hij dat het niet is toegestaan het apparaat in bedrijf te stellen tot de machine waarin het wordt ingebouwd of waar het een onderdeel
van zal worden is geïdentificeerd, en conform de vereisten van Richtlijn 98/73/EG is verklaard.
Grassobbio, 05-12-2006
De Algemeen Directeur
D. Gianantoni
INHOUDSOPGAVE
1. BESCHRIJVING EN TECHNISCHE EIGENSCHAPPEN pag.27
2. AFMETINGEN pag.27
3. MAXIMALE GEBRUIKSCURVE pag.27
4. ELEKTRISCHE AANSLUITMOGELIJKHEDEN (standaardinstallatie) pag.27
5. INSTALLATIE VAN HET AUTOMATISCHE SYSTEEM pag.28
5.1. CONTROLES VOORAF pag.28
5.2. INMETSELEN VAN DE FUNDERINGSPLAAT pag.28
5.3. MECHANISCHE INSTALLATIE pag.28
5.4. MONTAGE VAN DE TANDHEUGEL pag.28
6. INBEDRIJFSTELLING pag.29
6.1. AANSLUITING ELEKTRONISCHE KAART pag.29
6.2. PLAATSING VAN DE EINDSCHAKELAARS pag.29
7. TEST VAN HET AUTOMATISCHE SYSTEEM pag.30
8. HANDBEDIENDE WERKING pag.30
9. HERVATTING NORMALE WERKING pag.30
10. SPECIALE TOEPASSINGEN pag.30
11. ONDERHOUD pag.30
12. REPARATIES pag.30
13. ACCESSOIRES pag.30
Le descrizioni e le illustrazioni del presente manuale non sono impegnative. GENIUS si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’apparecchiatura,
di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per
qualsiasi altra esigenza di carattere costruttivo o commerciale.
The descriptions and illustrations contained in the present manual are not binding. GENIUS reserves the right, whils leaving the main features of the equipments unaltered, to
undertake any modifications to holds necessary for either technical or commercial reasons, at any time and without revising the present publication.
Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. GENIUS se réserve le droit d’apporter à tout moment les modifications qu’elle jugera utiles
sur ce produit tout en conservant les caractéristiques essentielles, sans devoir pour autant mettre à jour cette publication .
Las descripciones y las ilustraciones de este manual no comportan compromiso alguno. GENIUS se reserva el derecho, dejando inmutadas las características esenciales de
los aparatos, de aportar, en cualquier momento y sin comprometerse a poner al día la presente publicación, todas las modificaciones que considere oportunas para el
perfeccionamiento técnico o para cualquier otro tipo de exigencia de carácter constructivo o comercial.
Die Beschreibungen und Abbildungen in vorliegendem Handbuch sind unverbindlich. GENIUS behält sich das Recht vor, ohne die wesentlichen Eigenschaften dieses Gerätes
zu verändern und ohne Verbindlichkeiten in Bezung auf die Neufassung der vorliegenden Anleitungen, technisch bzw, konstruktiv / kommerziell bedingte Verbesserungen
vorzunehmen.
De beschrijvingen in deze handleiding zijn niet bindend. GENIUS behoudt zich het recht voor op elk willekeurig moment de veranderingen aan te brengen die het bedrijf
nuttig acht met het oog op technische verbeteringen of alle mogelijke andere productie- of commerciële eisen, waarbij de fundamentele eigenschappen van het apparaat
gehandhaafd blijven, zonder zich daardoor te verplichten deze publicatie bij te werken.
Timbro rivenditore: / Distributor’s stamp: / Timbre de l’agent: / Sello del revendedor: / Fachhändlerstempel: / Stempel dealer:
Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO-ITALY
tel. 0039.035.4242511
fax. 0039.035.4242600
www.geniusg.com
00058I0617 Rev.0
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Genius Falcon User manual

Category
Gate Opener
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI