Aiwa SX-C605 User manual

For assistance and information

call toll free I-800-BUY=AIWA

(United States and Puerto Rico)

8Z-NFV-903-01

981125 BMI-U-9

(ilD’BiE

DIGITAL AUDIO

Owner’s record

For your convenience, record the model number and serial

number (you will find them on the rear of your set) in the space

provided below. Please refer to them when you contact yourAiwa

dealer in case of difficulty.

Model No.

Serial No. (Lot No.)

CX-NMA545

SX-WNA555

SX-R275

SX-C605

Read the Operating Instructions carefully and completely before

operating the unit. Be sure to keep the Operating Instructions

for future reference. All warnings and cautions in the Operating

Instructions and on the unit should be strictly followed, as well

as the safety suggestions below.

Installation

1

2

3

4

5

6

7

8

Water and moisture — Do not use this unit near water, such

as near a bathtub, washbowl, swimming pool, or the like.

Heat — Do not use this unit near sources of heat, including

heating vents, stoves, or other appliances that generate heat.

It also should not be placed in temperatures less than 5°C

(41‘F) or greater than 35°C (95”F).

Mounting surface — Place the unit on a flat, even surface.

Ventilation — The unit should be situated with adequate

space around it so that proper heat ventilation is assured.

AHow 10 cm (4 in.) clearance from the rear and the top of the

unit, and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar surface that

may block the ventilation openings.

- Do not install the unit in a bookcase, cabinet, or airtight rack

where ventilation may be impeded.

Objects and liquid entry — Take care that objects or liquids

do not get inside the unit through the ventilation openings.

Carts and stands — When placed

or mounted on a stand or cart, the

unit should be moved with care.

Quick stops, excessive force, and

uneven surfaces may cause the m

3

AA*

unit or cart to overturn or fall.

Condensation — Moisture may form on the CD pickup lens

when:

- The unit is moved from a cold spot to a warm spot

- The heating system has just been turned on

- The unit is used in a very humid room

- The unit is cooled by an air conditioner

When this unit has condensation inside, it may not function

normally. Should this occur, leave the unit for a few hours,

then try to operate again.

Wall or ceiling mounting —The unit should not be mounted

on a wall or ceiling, unless specified in the Operating

Instructions.

Electric Power

1 Power sources — Connect this unit only to power sources

specified in the Operating Instructions, and as marked on the

unit.

2 Polarization — As a safety feature, some units are equipped

with polarized AC power plugs which can only be inserted

one way into a power outlet. If it is difficult or impossible to

insert the AC power plug into an outlet, turn the plug over and

try again. If it still does not easily insert into the outlet, please

call a qualified service technician to service or replace the

outlet. To avoid defeating the safety feature of the polarized

plug, do not force it into a power outlet.

3 AC power cord

- When disconnecting the AC power cord, pull it out by the

AC power plug. Do not pull the cord itself.

- Never handle the AC power plug with wet hands, as this

could result in fire or shock.

- Power cords should be firmly secured to avoid being severely

bent, pinched, or walked upon. Pay particular attention to

the cord from the unit to the power outlet.

- Avoid overloading AC power plugs and extension cords

beyond their capacity, as this could result in fire or shock.

2 ENGLISH

4

5

Extension cord — To help prevent electric shock, do not use

a polarized AC power plug with an extension cord, receptacle,

or other outlet unless the polarized plug can be completely

inserted to prevent exposure of the blades of the plug.

When not in use — Unplug the AC power cord from the power

outlet if the unit will not be used for several months or more.

When the cord is plugged in, a small amount of current

continues to flow to the unit, even when the power is turned

off

Outdoor Antenna

1

2

Power lines — When connecting an outdoor antenna, make

sure it is located away from power lines.

Outdoor antenna grounding — Be sure the antenna system

is properly grounded to provide protection against unexpected

voltage surges or static electricity build-up. Article 810 of the

National Electrical Code, ANS1/NFPA70, provides information

on proper grounding of the mast, supporting structure, and

the lead-in wire to the antenna discharge unit, as well as the

size of the grounding unit, connection to grounding terminals,

and requirements for grounding terminals themselves.

Antenna Grounding According to the National Electrical Code

n--

~ ANTENNA LEAD IN WIRE

—-----4 I

. ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRIC

SERVICE

EOuipMENT

GROuNDING c0NDucT08s

(NEC SECTION 810.21)

GROUND CLAMPS

, ~ POWER SERVICE GROUNOING

ELECTRODE SYSTEM

(NEC ART 250 PART H)

NEC-NATIONAL ELECTRICAL CODE

Maintenance

Clean the unit only as recommended in the Operating

Instructions.

Damacre Requiring Service

Have the units serviced by a qualified service technician if:

- The AC power cord or plug has been damaged

- Foreign objects or liquid have gotten inside the unit

- The unit has been exposed to rain or water

- The unit does not seem to operate normally

- The unit exhibits a marked change in performance

- The unit has been dropped, or the cabinet has been damaged

DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF.

Precautions ...........................................m.......................2

PREPARATIONS

SETTING UP ....................................m..................................4

REMOTE CONTROL ...........................................................7

BEFORE OPERATION .......s................................................7

SOUND

AUDIO ADJUSTMENTS .................................................. 10

GRAPHIC EQUALIZER ...................................................

10

RADIO RECEPTION

MANUAL TUNING ..............#............m.................................ll

PRESETTING STATIONS ................................................ 12

TAPE PLAYBACK

BASIC OPERATIONS ...................................................... 13

CD PLAYING

BASIC OPERATIONS ...................................................... 14

PROGRAMMED PLAY .......................................m............. 15

RECORDING

BASIC RECORDING ........................................................ 16

DUBBING A TAPE MANUALLY ...................................... 17

DUBBING THE WHOLE TAPE

........................................ 17

Al EDIT RECORDING ...................................................... 18

PROGRAMMED EDIT RECORDING ............................... 19

❑

DOLBY PRO LOGIC

ADJUSTING SPEAKER LEVEL BALANCE ...................20

PLAY WITH DOLBY PRO LOGIC ................................... 21

KARAOKE

MICROPHONE MIXING ................................................... 22

KARAOKE PROGRAM .................................................... 23

CLOCK AND TIMER

SETTING THE CLOCK .................................................... 24

SETTING THE SLEEP TIMER ......................................... 24

SETTING THE TIMER ...................................................... 25

OTHER CONNECTIONS

CONNECTING OPTIONAL EQUIPMENT ....................... 26

LISTENING TO EXTERNAL SOURCES ......................... 26

GENERAL

CARE AND MAINTENANCE ........................................... 27

TROUBLESHOOTING GUIDE ......................................... 27

SPECIFICATIONS ............................................................ 28

PARTS INDEX ...................................................

Back cover

ENGLISH

3

The DOLBY PRO LOGIC system which is the biggest feature of

this stereo system provides you with multi channel sound in your

home.

Complete setting and connection of the main unit, supplied

speakers, your TV and video equipment according to the following

procedure.

Check your system and accessories

CX-NMA545 Compact disc stereo cassette receiver

SX-WNA555 Front speakers

SX-R275 Surround speaker

SX-C605 Center speaker

Remote control

AM antenna

FM antenna

Operating Instructions, etc

To achieve the optimum effects obtainable with the DOLBY PRO

LOGIC system, it is important to position the speakers properly.

Refer to the following illustration to find out the best location in

your room.

O Front speakers

@ Center speaker

● No sound is heard from the center and surround speakers when

the DOLBY PRO LOGIC is set to off.

● The center speaker sounds when the DOLBY PRO LOGIC is

set to on.

CONNECTIONS

Before connecting the AC cord

The rated voltage of your unit shown on the rear paneI is 120 V

AC, Check that the rated voltage matches your local voltage,

IMPORTANT

Connect the speakers, antennas, and all optjonal equipment first.

Then connect the AC cord.

There are no differences between the fr,ont speakers. Both

speakers can be connected as L (left) or RI(right).

1

2

Connect the right speaker to the main unit.

@

Connect the speaker cord with the plug to the SPEAKERS

HIGH FREQ R terminal.

@ Connect the speaker cord with the ‘white stripe to the

SPEAKERS LOW FREQ R ~ terminal and the black cord

to the O terminal.

@

#

o

#

-*

.,. *

●

e

Connect the left speaker to the rhain unit.

Connect the speaker cord with plug to the SPEAKERS HIGH

FREQ L terminal, and another speaker cord to the

SPEAKERS LOW FREQ L terminals in the same manner as

step 1.

Position in the center of the two front speakers. In addition,

position on or below the TV set, if connecting a TV set to the

unit.

@ Surround speakers

Place the surround speakers directly to the side of or slightly

behind the listening area. Align them horizontally, about 1

meter (3.2 feet) above ear height.

4 ENGLISH

.-

A

FM antenna

~ Center speaker ‘-~~c

1

Riaht s~eaker

r

L’

r

5

AM antenna

Q

b

u Ill

-

3

Surround speaker

J

—

3 Connect the surround speakers.

Connect the surround speaker cords to SURROUND

4

SPEAKERS terminals.

There is no difference between the surround speakers. Both

speakers can be connected as R (right) or L (left).

Connect the center speaker.

Connect the center speaker cord to CENTER SPEAKER

terminal.

5 Connect the supplied antennas.

Connect the FM antenna to FM 75 Q terminals and the AM

❑

6

7

8

antenna to AM LOOP terminals.

FM antenna

)T(

AM antenna

Connect the video equipment,

Connect VIDEO/AUX jack of this unit to the audio output jack

of the video equipment with an optional audio connecting cord.

Connect the Television to the video equipment.

Refer to the Operating Instructions of the connected

equipment for details.

Connect the AC cord to an AC outlet.

The game Demo will begin when the AC cord is plugged into

an AC outlet. See page 8 “Game Demo” for details.

ENGLISH5

To position the antennas

FM feeder antenna:

Extend this antenna horizontally in a T-shape and fix its ends to

the wall.

AM antenna:

Position to find the best possible reception.

To stand the AM antenna on a surface

Fix the claw to the slot.

m

● Be sure to connect the speaker cords correctly. Improper

connections can cause short circuits in SPEAKERS terminals.

● Do not leave objects generating magnetism, such as credit

cards, near the speakers, as these objects may be damaged.

● Do not bring the FM antenna near metal objects or curtain rails.

● Do not bring the AM antenna near other optional equipment,

the stereo system itself, the AC cord or speaker cords, since

noise will be picked up.

c Do not unwind the AM antenna wire.

For better FM reception, use of an outdoor antenna is

recommended.

Connect the outdoor antenna to FM 75 Q terminals.

To mount the surround speakers on the wall

Mount each speaker on a s~ot that can hold its weiaht.

To connect other optional equipment+ page 26.

6 ENGLISH

Inserting batteries

Detach the battery cover on the rear of the remote control and

inserf two R6 (size AA) batteries.

w’”

@

Go

MULTIJ

ENTER

R6(AA)

When to replace the batteries

The maximum operational distance between the remote control

and the sensor on the main unit should be approximately 5 meters

(16 feet). When this distance decreases, replace the batteries

with new ones.

Using the remote control

The instructions in this manual refer mainly to the buttons on the

main unit. Buttons on the remote control with the same names

as those on the main unit can be used as well.

-/+> PRESET on the remote control

The function is the same as that of P on the main unit.

b/4 ➤

PRESET

m

● If the remote control is not going to be used for an extended

period of time, remove the batteries to prevent possible

electrolyte leakage.

● The remote control may not operate correctly when:

- The line of sight between the remote control and the remote

sensor inside the display window is exposed to intense light,

such as direct sunlight

- Other remote controls are used nearby (those of a television,

etc.)

ECO

To turn

the power on

Press one of the function buttons (TAPE, TUNER, VIDEO/AUX,

CD). Playback of the inserted disc or tape begins, or the

previously tuned station is received (Direct Play Function).

POWER is also available.

When the power is turned on, the disc compartment may open

and close to reset the unit.

To turn the power off

Press POWER.

Flash window

The window on the top of the unit lights up or flashes while the

unit is being powered on.

To turn off the light of the top window, press

■ while pressing

❑

CD. To turn back on, repeat the above.

To change the brightness level of the display

1 Press ECO so that “ECO MODE” is displayed.

2 Within 4 seconds, turn MULTI JOG to display “DIM MODE”,

and then press ENTER within 4 seconds.

3 Within 4 seconds, turn MULTI JOG to select the dimmer mode

as below.

The mode will be automatically set after 4 seconds. It will

also be set if ENTER is pressed within 4 seconds after step

3.

r

DIM-OFF +-+ DIMMER 1 +-+ DIMMER 2~DlMMER 3

7

DIM-OFF: The normal display.

DIMMER 1: The illumination of the display is dimmer than

usual.

DIMMER 2: The illumination of the display is dimmer than

DIMMER 1.

DIMMER 3: The illumination of the display is dimmer than

DIMMER 2. The spectrum analyzer, the window on the top of

the unit, and the button lamps light off.

m

If the timer recording (page 25) is done with the economizing

mode (page 9) set to “ON” and the power turns off, the dimmer

mode will be set to “DIMMER 3 the next time the power is

turned on.

ENGLISH 7

When the AC cord is plugged into an AC outlet for the first time

after purchase, the game Demo will begin in the display. When

the power is turned on, the game Demo will end. When the power

is turned off, the game Demo will begin again.

Until the clock is set, the game Demo will begin whenever the

power is turned off.

When the clock is set, the game Demo will not begin even if the

power is turned off,

To start or end game Demo when the clock is set

Press E when the power is off, the game Demo will begin.

To end the game Demo, press CLOCK.

To play the game Demo

1

2

3

To start the game Demo, press ~

(when the clock

is set and the power is turned off) or press

POWER to turn off the power (when the clock is

not set).

Three numbers on the display start to run.

Press Z once.

The number on the left side stops.

Press ■ twice to stop the remaining two

numbers.

Scoring:

20

points are given to start the game.

[fall the numbers are eaual, 50 points are added to the score.

If not eaual, one point is subtracted.

If the gained points reach 9999, you win.

If the gained points fall to O,you lose.

To reset the game Demo

Press CLOCK, then press F (when the clock is set).

Press POWER twice to turn the power on/off (when the clock is

not set). The game starts again.

To change the probability of equalizing the three numbers

Press + or > repeatedly to select one of the three probability

levels when playing the game Demo. The tray number indicator

in the display changes between 1 and 3. As the tray number

increases from 1 to 3, the higher the probability of equalizing.

rl-2-3~

● While playing the game Demo, ■, 44, ~ and - are

available only for the game Demo. Turn the power on to use

these buttons for the functions such as CD playing, etc.

● During the game Demo, some indicators unrelated to the actual

operation light up on the display.

8 ENGLISH

Setting this unit to power economizing mode reduces power

consumption as follows.

● When the power is turned off, all the display lights turn off.

However, if the clock is not set, the game Demo (page 8) will

begin when the power is turned off.

● If CD or Tape does not play for 10 minutes or if there is no

audio input from any connected external equipment for 10

minutes when VIDEO/AUX is selected as the source, the power

shuts

Off.

● When the power turns on due to timer recording (page 25), the

display brightness level is set to “DIMMER 3 (page 7), all button

lamps are off, and the volume is set to the minimum level (0).

● The display brightens only when operating the unit, When the

unit has not been used for 10 seconds, the brightness level

switches to the mode previously selected in “DIM MODE. (Page

7)

(If the display brightness level is set to “DIM-OFF”, the

brightness does not change. When the level is “DIMMER 3,

the button lamps are also turned off,)

1

2

3

Press ECO.

“ECO MODE” will be displayed,

Press ENTER within 4 seconds.

The current power-economizing mode status will be displayed.

If the power-economizing mode is OFF: ECO OFF

If the power-economizing mode is ON: ECO ON

Turn MULTI JOG within 4 seconds to switch the

power-economizing mode on or off.

Example: When “ON” is selected

The mode will be automatically set after 4 seconds. It will

also be set if ENTER is pressed within 4 seconds after step

3.

To provide reinforcement for the ultra-low frequencies, in addition

to the Left/Right 2-channel amplifier used to reproduce mid-to-

high-range frequencies, this system incorporates a second L/R

2-channel amplifier just for reproduction of ultra-low frequencies

.

making it, in effect, a 4-amplifier system. By utilizing discrete

amplifiers for mid to-high-frequencies and low frequencies, high-

quality sonic reproduction that is virtually free from distortion can

be realized.

This Multi Amplifier System, which utilizes independent circuitry

for the different frequency ranges, enables superb sonic

reproduction free from distortion,

The built-in subwoofer System has a separate subwoofer cavity

area that is part of the loudspeaker cabinet structure, which acts

as a sonic filter to cut distortion components. (In the Multi Amplifier

System, the ultra-low frequency signals transmitted from their

own independent amplifier are reproduced in this area.) This

separate construction gives a clear, rich definition to bass

reproduction and it can realize clear, well-defined mid-to-high

frequency signals.

And AlWA’s built-in subwoofer system incorporates a subwoofer

capable of powerful, satisfying bass performance with true stereo

separation.

Amplifiers for Mid-to-high

range frequencies

/ IF “’!4 -I:im 1 [

m

Toview the clock when all the display lights turn off, press CLOCK

so that the time is displayed for 4 seconds.

ENGLISH 9

GRAPHIC EQUALIZER

T-BASS

MANUAL

SELECT

VOL

M

PHONES.

u

i DOWN

~ >Up’

‘....__.....’

Turn VOLUME on the main unit, or press VOL on the

remlote control.

The volume level is displayed as a number from Oto MAX (50).

The vollume level is automatically set to 20 when the power is

turned off with the volume level set to 21 or more.

To change the Ieftiright balance

Press MANUAL SELECT on the remote control. L/R is displayed

for 2 seconds. Press+ DOWN or

➤> UP on the remote control

within these 2 seconds.

● The DOLBY PRO LOGIC front speakers level is also changed.

(See page 20)

The T-13ASS system enhances the realism of low-frequency

sound.

Press ‘T-BASS.

Each time it is pressed, the level changes. Select one of the

three levels, or the off position to suit your preference.

(ROCK,POP,CLASSIC)

,&

I ri

m

u

‘<..__-.....

–GEQ

This unit provides the following three different equalization curves.

ROCK: Powerful sound emphasizing treble and bass

POP: More presence in the vocals and midrange

CLASSIC: Enriched sound with heavy bass and fine treble.

Press one of ROCK, POP or CLASSIC.

The selected equalization mode is displayed,

To cancel the selected mode

Press the selected button again. “GEQ OFF is displayed.

To select with the remote control

Press GEQ repeatedly. The GEQ mode is displayed cyclically

as follows.

ROCK— POP— CLASSIC— GEQ OFF

(cancel)

m

Low frequency sound may be distorted when the T-BASS system

is used for adisc or tape in which low frequency sound isoriginally

emphasized. In this case, cancel the T-BASS system.

Using the headphones

Connect headphones to the PHONES jack with a standard stereo

plug (06.3 mm, ‘/4 inch).

No sound is output from the speakers while the headphones are

plugged in.

● When the headphones are plugged in, the DOLBY PROLOGIC

is canceled.

Sound adjustment during recording

The output volume and tone of the speakers or headphones are

freely varied without affecting the recording.

10 ENGL/SH

1

2

TUNER

BAND

Press TUNER BAND repeatedly to select the

desired band.

r-

FM — AM

When TUNER BAND is pressed while the power is off, the

power is turned on directly.

Press + DOWN or - UP to select a station.

Each time the button is pressed, the frequency changes.

When a station is received, “TUNE is displayed for 2 seconds.

During FM stereo reception, (l@Il] is displayed.

TUNE

[(lam]]

When an FM stereo broadcast contains noise

,-:-

,,:=~,,

Press MONO on the remote control so that “MONO appears on ~g$~

the display.

*

&

1$

t.

Noise is reduced. althouah recerXion is monaural.

#~&$

@

To restore stereo receptfin, repeat the above so that “MONO ~“ ~~

disappears.

3,,,.‘,>

$&&a$

,’$~

..

To change the AM tuning interval

The default setting of the AM tuning interval is 10 kHz/step. If Z

you use this unit in an area where the frequency allocation system o

is 9 kHz/step, change the tuning interval.

I

-,,

,g=?,?

Press POWER while pressing -.

yi

/g ,r

To reset the interval, repeat this procedure.

w

~=,

&

,,

m

~:gj

if VI!

1!

* ??

When the AM tuning interval is changed, all preset stations are “

cleared. The preset stations have to be set again.

4

&

To search for a station quickly (Auto Search)

Keep + DOWN or ~ UP pressed until the frequency starts

to change rapidly. After tuning in to a station, the search stops.

To stop the Auto Search manually, press ++ DOWN or -

UP.

● The Auto Search may not stop at stations with very weak

signals.

ENGLISH

11

The unit can store a total of 32 preset stations. When a station is

stored, a preset number is assigned to the station. Use the preset

number to tune in to a preset station directly.

1

2

3

Press TUNER BAND to select a band, and press

+ DOWN or _ UP to select a station.

Press II SET to store the station.

A preset number beginning from 1 in consecutive order for

each band is assigned to the station.

Preset number

Repeat steps 1 and 2.

The next station will not be stored if a total of 32 preset stations

for all the bands have already been stored.

m

Use the remote control to select the preset number directly.

1 Press TUNER BAND to select a band.

2 Press numbered buttons O-9 and +10 to select a

preset number.

Example:

To select preset number 20, press +1O,+1Oand O.

To select preset number 15, press +10 and 5.

Selecting a preset number on the main unit

Press TUNER BAND to select a band. Then, press> repeatedly

or turn MULTI JOG.

Each time E is pressed, the next ascending number is selected.

To clear a preset station

Select the preset number of the station to be cleared. Then, press

■ CLEAR, and press 11 SET within 4 seconds.

The preset numbers of all other stations in the band with higher

numbers are also decreased by one.

“FULL” is displayed if you attempt to store more than 32 preset

stations.

12 ENGLISH

This unit is designed for optimal playback of Type I

(normal) tapes.

1

2

Press TAPE and press A PUSH EJECT to open

the cassette holder.

APUSH

EJECT-

LIu

Insert a tape with the exposed side down. Push the cassette

holder to close.

Press F to start play.

Only the side facing out from the unit can be played back.

Selected deck number

To select a playing deck

When tapes are loaded in both decks, press TAPE first to select

a deck.

The selected deck number is displayed.

To stop play, press

■ .

To pause play (deck 2 only), press Il. To resume play, press

again.

To fast forward or rewind, press + or -. Then press

■

to stop the tape.

To start play when the power is off (Direct Play Function)

Press TAPE. The power is turned on and play of the inserted

tape begins.

To set the tape counter to 0000

Press

■ CLEAR in stop mode.

The counter is also set to 0000 when the cassette holder is

opened.

When tapes are loaded in both decks

After playback on deck 1finishes, the tape in the deck 2 will start

to play without interruption and will stop at the end of the tape.

(Continuous play)

m

High position tapes can also be played back in this unit. When

playing back a Type II tape, turn MULTI JOG to display “SOF~

in the display. This will set the optimum playback sound for Type

II tapes. However, “SOFT” playback will be canceled if any

graphic equalizer is selected (page 10), the unit is switched to a

different audio source, the cassette holder is open, or when the,

power is turned off.

Tape counter

ENGLISH 13

1111

CHECK

Ilh Ill

qi

++,- ,;J

8

1

.= ---- -------- ---- .\

! ,-

1

Q

CD BLANK SKIP

P CD EDIT/CHECK

Press CD, then press A OPEN/CLOSE to open the

disc compartment. Load disc(s) with the label side

up.

To dav one or two discs, place the discs on tray 1 and 2.

To dav three discs, press DISC CHANGE to rotate the trays

after placing two discs. Place the third disc on tray 3.

Close the disc compartment by pressing 4 OPEN/CLOSE.

DISC GHANGE

Tray number of the

disc to be played Total playing time

Total number of tracks

Load discs.

To tiav all discs in the disc com~artment, press E.

Play begins with the disc on tray 1.

Number of track being played

Elapsed playing time

To play one disc only, press DISC DIRECT PLAY 1-3.

The selected disc is played once.

To stop play, press 9.

To pause play, press 11. To resume play, press again.

To search for a particular point during playback, keep -

or > pressed and release it at the desired point.

To skip to the beginning of a track during playback, press

+ or ~ repeatedly or turn MULTI JOG.

To remove discs, press A OPEN/CLOSE.

To start play when the power is off (Direct Play Function)

Press CD. The power is turned on and play of the loaded disc(s)

begins.

When 4 OPEN/CLOSE is pressed, the power is also turned on

and the disc compartment is opened.

To check the remaining time

During play, press CD EDIT/CHECK. The amount of time

remaining until all tracks finish playing is displayed. To restore

the playing time display, repeat the above.

Selecting a track with the remote control

1 Press DISC DIRECT PLAY, then press numbered buttons 1-

3 within 3 seconds to select a disc.

2 Press numbered buttons O-9 and +1Oto select a track.

Example:

To select the 25th track, press +10, +10 and 5.

To select the 10th track, press +10 and O.

The selected track starts to play and continues to the end of

that disc.

Replacing discs during play

While one discisplaying,the otherdiscs can be replaced without

interrupting play.

1 Press DISC CHANGE.

2 Remove the discs and replace with other discs.

3 Press A OPEN/CLOSE to close the disc compartment.

● When loading an 8-cm (3-inch) disc, put it onto the inner circle

of the tray,

● Do not place more than one compact disc on one disc tray.

● Do not tilt the unit with discs loaded. Doing so may cause

malfunctions.

● Do not use irregular shape CDs (example: heart-shaped,

octagonal ones). It may result in malfunctions.

14 ENGLISH

RANDOM /REPEAT PLAY

Use the remote control,

RANDOM play

All the tracks on the selected disc or all the discs can be played

randomly.

REPEAT play

A single disc or all the discs can be played repeatedly.

Press RANDOM/REPEAT.

Each time it is pressed, the function can be selected cyclically.

RANDOM play — RANDOM lights up on the display,

REPEAT play — % lights up on the display.

RANDOM/REPEAT play — RANDOM and ~ light upon the

display.

Cancel — RANDOM and C& disappear from the display.

To ~lav all discs, press ~ to start play.

To play a single disc, press one of DISC DIRECT PLAY 1-3 to

start play.

m

During random play it is not possible to skip to the previously

played track with +,

1 Press CD BLANK SKIP.

“CD BLANK SKIP ON” is displayed and a small dot will appear

in the display.

Small dot

2 Press F to start playback.

The silent portions between tracks will be skipped, and the

sound will be played back without interruption. If atrack fades

out (ends with the sound gradually decreasing), the fadeout

portion also will be skipped.

To return to normal playback

Press CD BLANK SKIP again, and the dot in the display will

disappear.

m

“

There may be a case where BLANK SKIP PLAY does not

function correctly.

“ BLANK SKIP PLAY is automatically canceled when performing

Al EDIT RECORDING (page 18), PROGRAMMED EDIT

RECORDING (page 19), or recording during PROGRAMMED

PLAY (page 15) or RANDOM PLAY (page 15).

upto 30

discs.

tracks can be programmed from any of the inserted

1

2

5

44,*

■

Use the remote control.

1

2

3

4

5

Press PRGM twice in stop mode.

“PRG” is displayed

● When the PRGM is pressed once in step 1, the unit enters

the KARAOKE PROGRAM (page 23).

Press DISC DIRECT PLAY, then press numbered

buttons 1-3 within 3 seconds to select a disc.

Go to the next step when the tray stops rotating.

Press numbered buttons O-9 and +1Oto program

a track.

Example:

To select the 25th track, press +10, +10 and 5,

To select the 10th track, press +10 and O.

Total number of

Selected track number

Program number

selected tracks

Total playing time of

the selected tracks

Repeat steps 2 and 3 to program other tracks.

Press - to start play.

To check the program

Each time - or - is pressed in stop mode, a disc number,

track number, and program number will be displayed.

To clear the program

Press

■ CLEAR in stop mode,

To add tracks to the program

Repeat steps 2 and 3 in stop mode. The track will be programmed

after the last track.

To change the programmed tracks

Clear the program and repeat all the steps again

To play the programmed tracks repeatedly

After programming the tracks, press RANDOM/REPEAT

repeatedly until CL appears on the display.

● During programmed play, you cannot perform random play,

check the remaining time, and select a disc or track, “CAN’T

USE” is displayed if you attempt to select a track.

● “FULU is displayed if you attempt to program more than 30

tracks.

ENGLISH 15

This section explains how to record from the tuner, CD player, or

!xternal equipment.

●/OREC/

REC MUTE

b/4b

u

L

- -----

J

Preparation

● Use Type I (normal) tapes only.

● Set the tape’ to the point where recording will start.

● Note that recording is done on only one side of the tape,

1

2

3

Insert the tape to be recorded on into deck 2.

Insert the tape with the side to be recorded on first facing out

from the unit.

.A PUSH EJECT

I

UIJ

Press function (CD, TUNER or VIDEO/AUX) and

prepare the source to be recorded.

To record from a CD, press CD and load the disc(s).

To record from a radio broadcast, press TUNER and tune

in to a station.

To record from a connected source, press VIDEO/AUX.

Press

● REC/REC MUTE to start recording.

When recording from a connected source, start play~ack of

the source.

m

When the selected function is CD, playback and recording

start simultaneously.

To stop recording, press 9.

To pause recording, press II. (Applicable when the source is

TUNER or VIDEO/AUX) To resume recording, press it again.

Sound adjustment during recording

The output volume and tone of the speakers or headphones are

freely varied without affecting of the recording.

,-...,.,.,.,..%-,,,,...,,,,,,m.*,m.,,,-,,* *,.,,,,:*’‘-’-

..,,.wak,=........ .

—....

w.**,-:.* m.@,m.=-,**xw$w3!w,*,w*M*%:

INSERTING BLANK SPACES

Insertion of 4-second blank spaces enables you to activate the

Music Sensor function. (Applicable when the source is TUNER

or VIDEO/AUX.)

1

2

Press

● REC/REC MUTE during recording or while in

recording pause mode.

~ onthe displayflashes for

4 seconds and 4-second blank

space is made. Then, the deck enters the recording pause

mode.

Press II to resume recording.

To insert a blank s~ace of less than 4 seconds, press

●

REC/REC MUTE again while ~ is flashing.

To insert blank s~aces of more than 4 seconds, after the deck

enters recording pause mode, press

● REC/REC MUTE again.

Each time the button is pressed, a 4-second blank space is

added.

About cassette tapes

. To prevent accidental erasure, break offthe plastictabs

on the cassette tape after recording with a screwdriver or

other pointed tool.

Side A

Tab for side A

To record on the tape again, cover the tab openings with

adhesive tape, etc.

● 120-minuteor longer tapes are extremely thin and easily

deformed or damaged. They are not recommended.

● Take up any slack in the tape with a pencil or similar tool

before use, Slack tape may break orjam inthe mechanism.

m

“CAN’T REC” is displayed if you attempt to record on a tape with

the plastic tabs broken off.

To start recording with the remote control

First press

●/0 REC/REC MUTE, and then press W<> within

2 seconds.

16

ENGL/SH

To erase a recording

Make sure the microphone is not connected to this unit.

Turn MIC MIXING control to MIN (See page 22).

1 Insert the tape to be erased into deck 2 and press TAPE DECK

1/2 to display “TP 2.

2 Set the tape to the point where the erasure is to be started.

3 Press

● REC/REC MUTE to start the erasure.

m

● Set the tape to the point where recording will start.

● Note that recording will be done on one side of the tape only.

1

2

3

4

Press TAPE.

Insert the original tape into deck 1 and the tape

to be recorded on into deck 2.

Insert the tapes with the sides to be played back or recorded

on facing out from the unit.

Press TAPE DECK 1/2 to select deck 1.

“TP 1” is displayed.

Press ● REC/REC MUTE to start recording.

Playing and recording start simultaneously.

To stop dubbing

Press 9.

1

9

This function allows you to make exact copies of the original

tape.

● Dubbing does not start from a point halfway in the tape.

● Note that recording will be done on one side of the tape only.

1

2

3

Press TAPE.

Insert the original tape into deck 1 and the tape

to be recorded on into deck 2.

Insert each tape with the side to be played back or recorded

on facing out from the unit.

Press SYNC DUB to start recording.

The tapes are rewound to the beginning of the front sides,

and recording starts.

To stop dubbing

Press H.

ENGLISH I 7

1,8

CD EDITI

CHECK

5

The Al edit recording function enables CD recording without

worrying about tape length and track length. When a CD is

inserted, the unit automatically calculates the total track length.

If necessary, the order of tracks is rearranged so that no track is

cut short.

(Al: Artificial Intelligence)

m

Al edit recording will not start from a point halfway into the tape.

The tape must be recorded from the beginning of either

side.

1

2

3

4

5

Insert the tape into deck 2.

Insert the tape with the side to be recorded on first facing out

from the unit.

Press CD and load the disc(s).

Press CD EDiT/CHECK W.

“EDIT” is displayed.

EDIT

● When “PRGM” is displayed, press CD EDIT/CHECK.

Press

DISC DIRECT PLAY 1-3 to select a disc.

Press numbered buttons O-9 on the remote

control to designate the tape length.

10 to 99 minutes can be specified.

Example: When using a 60-minute tape, press 6 and O.

In a few seconds, the tracks to be recorded on each side of

the tape are determined.

● w, w or MULTI JOG are also available to designate

the tape length.

Tape length

Remaining time Programmed

of recording tracks for side A

6

7

8

Press

● REC/REC MUTE to start recording on

the first side.

The tape is rewound to the beginning of the first side, the

lead segment is played through

for 10 seconds, and recording

starts. When the last track programmed for side A is finished,

deck 2 enters the recording stop mode. After entering the

recording stop mode, go to step 7.

Press CD EDIT/CHECK to display the program for

the second recording.

“B” is displayed.

Turn over the tape in deck 2 and press ● REC/

REC MUTE to start recording on the second side.

To stop recording

Press

■ . Recording and CD play stop simultaneously.

To clear the edit program

Press

■ CLEAR twice sothat “EDIT disappears on the display.

To check the order of the programmed track numbers

Before recording, press CD EDIT/CHECK to select side A or B,

and press 4 or * repeatedly.

Programmed

Track number

track numbers

Tape side Program number

To add tracks from other discs to the edit program

If there is any time remaining on the tape after step 5, you can

add tracks from other discs in the CD compartment.

1 Press CD EDIT/CHECK to select side A or B.

2 Press DISC DIRECT PLAY 1-3 to select a disc.

3 Press numbered buttons on the remote control to select tracks.

A track whose playing time is longer than the remaining time

cannot be programmed.

4 Repeat steps 2 and 3 to add more tracks.

Time

on cassette tapes and editing time

The actual cassette recording time is usually a little longer than

the specified recording time printed on the label. This unit can

program tracks to use the extra time. When the total recording

time is a little longer than the tape’s specified recording time

after editing, the display shows the extra time (without a minus

mark), instead of the time remaining on the tape (with the minus

mark).

m

The Al edit recording function cannot be used with discs

containing 31 tracks or more. “TR OVER” is displayed if this is

attempted.

Tape side

A: First recording side

B: Second recording side

18 ENGLISH

~CD EDIT/

/:. . ....- . ....~ ------

--;)

1,10 L

J’

In the programmed edit recording function the tracks can be

programmed while checking the remaining time on each side of

the tape.

The programmed edit recording will not start from a point halfway

in the tape. The tape must be recorded on from the beginning of

either side.

1

2

3

4

5

Insert the tape into deck 2.

Insert the tape with the side to be recorded on first facing out

from the unit.

Press CD and load the disc(s).

Press CD EDIT/CHECK twice

—.

“EDIT” and “PRGM” are displayed.

● When “Al” is displayed, press CD EDIT/CHECK again.

Press numbered buttons on the remote control

to designate the tape length.

10 to 99 minutes can be specified.

“ The -, - or MULTI JOG are also available to designate

the tape length.

Tape length Tape side A (front side)

Maximum recording

time for side A

Press DISC DIRECT PLAY 1-3 to select a disc.

Then, press numbered buttons O-9 and +10 on

the remote control to program a track.

Example: To select the 10th track of disc 2, press DISC

DIRECT PLAY 2, then press +10 and O.

Remaining time

Programmed

Selected track number

on side A

tracks

6

7

8

9

Repeat step 5 for the rest of the tracks for side “=,

A.

#-

;$

t

A track whose playing time is longer than the remaining time $ .*

cannot be programmed.

!l~

@

jg

p

Press CD EDIT/CHECK to select side B and M‘ $

program the tracks for side B.

‘@

After confirming “Bon the display, repeat step 5.

Tape side B (reverse side)

Press CD EDIT/CHECK to select side A and press

● REC/REC MUTE to start recording.

The tape is rewound to the beginning of the front side, the

lead segment is played through for 10 seconds, and recording

starts. When the last track programmed for side A is finished,

deck 2 enters the recording stop mode. After entering the

recording stop mode, go to step 9.

Press CD EDIT/CHECK for recording of the

second side.

“B

is displayed.

10 Turn over the tape in deck 2 and press @ REC/

REC MUTE to start recording.

Recording starts.

To stop recording

Press

■ . Recording and CD play stop simultaneously.

To check the order of the programmed track numbers

❑

Before recording, press CD EDIT/CHECK to select side A or B,

and press U or - repeatedly.

Programmed track

Disc number Track number

numbers

Tape side Program number

To change the program of each side

Press CD EDIT/CHECK to select side A or B, and press E

CLEAR to clear the program on the selected side. Then program

tracks again.

To clear the edit program

Press

■ CLEAR twice sothat “EDIT”disappears on the display.

m

● Up to 30 tracks can be programmed from any of the inserted

discs.

● “FULL” is displayed if you attempt to program more than 30

tracks.

Program number

ENGLISH 19

The DOLBY PRO LOGIC feature and the center and rear

speakers (standard) assure full-scale home theater sound. When

playing back laser discs or video software that have been

recorded in Dolby Surround, astonishingly realistic sound

surrounds the listener to create a new level of audio/visual

entertainment.

Independent control of the four sound channels allows the listener

to enjoy the same type of sound reproduction experienced in

movie theaters. Voices are reproduced in the front and center

sound field, while ambient sounds like cars and crowds are

reproduced on all sides of the listener for an incredibly lifelike

audio/video experience. Please read the following carefully to

“tune” the system’s output to match the characteristics of your

listening space.

Check the following:

● Before using the DOLBY PRO LOGIC, adjust the proper

balance of speaker sound levels.

● Make sure the supplied speakers are properly connected and

positioned. (See page 4 and 5)

● Make sure the TV set and video unit are properly connected.

(See page 5)

● Make sure the laser disc, video tape, etc., support

Do ~00L6v

SURROUND\ .

1’~k

8

/

]i

._________.—————_—

The unit is equipped with a built-in test signal generator called a

noise sequencer for easy balance adjustment of all 4 channels.

The sequencer outputs a noise signal that “travels” from channel

to channel, enabling the simple adjustment of sound level

to

achieve, at the listening position, the same apparent loudness

from each channel.

Use the remote control.

1

Press DOLBY PRO LOGIC to select “NORMAL”.

“NORMAL” is displayed.

If “PHANTOM” or “3 STEREO” is displayed, press DOLBY

PRO LOGIC repeatedly until “NORMAL” is selected.

2

3

4

Press MANUAL SELECT and hold it down for

about 4 seconds until “L” flashes.

A noise signal is sent to each channel in turn in the following

sequence.

L: Left speaker+ CEN: Center speaker-R: Right speaker

SUR: Surround speakers <

Adjust the sound level of the center and the

surround speakers.

While “CEN” or “SUR is displayed, press + DOWN or >

UP on the remote controlto adjust the volume of the center

or each surround speaker to match the level of the front

speakers.

To adjust the balance between the left and right front speakers,

see page 10. At this time, the DOLBY PRO LOGIC mode

should be canceled by pressing DOLBY PRO LOGIC until

the “PRO-OFF is displayed.

Press MANUAL SELECT again to stop the noise

signal.

m

When the sequencer outputs a noise signal, a clicking sound

might be heard from the speakers due to the characteristics of

the circuit. This is not malfunction.

About the channels

The left and right front speakers create the stereo effect.

The center speaker helps achieve precise sound positioning

over a broad sound field.

The rear-mounted surround speakers enhance the “depth” of

the sound field.

To change the delay time

The surround speakers reproduce sounds a split second after

the front speakers. The delay is initially set to 20 ms

(milliseconds).

To change this standard delay time, press MANUAL SELECT

onthe remotecontrolrepeatedly until“TIME is displayed. Then,

press ~ DOWN or - UP, Each time one of the buttons is

pressed, the delay time changes as shown below.

15mS+20mS++30mS

20 ENGLISH

Page is loading ...

Aiwa SX-C605 User manual

Aiwa SX-C605 User manual

in other languages

Related papers

Other documents