Actron 9640 User manual

Actron
Brand
Actron
Model
9640
Type
User manual

This manual is also suitable for

Actron 9640 is a versatile scan tool that provides comprehensive diagnostic capabilities for various vehicle systems. It enables users to retrieve and interpret diagnostic trouble codes (DTCs), view live data streams, perform actuator tests, and access vehicle-specific information. With its user-friendly interface and wide compatibility with domestic and import vehicles, the Actron 9640 empowers users to diagnose and troubleshoot automotive issues efficiently.

Actron 9640 is a versatile scan tool that provides comprehensive diagnostic capabilities for various vehicle systems. It enables users to retrieve and interpret diagnostic trouble codes (DTCs), view live data streams, perform actuator tests, and access vehicle-specific information. With its user-friendly interface and wide compatibility with domestic and import vehicles, the Actron 9640 empowers users to diagnose and troubleshoot automotive issues efficiently.

9640UB UPGRADE
STEP 1
Disconnect Scan Tool and cables from vehicle.
Installation of CAN
Adapter Board
STEP 5
Inspect connector pins on circuit board making sure pins
are straight and not bent.
Before installing CAN adapter board
straighten any bent connector pins.
!
CAUTION
STEP 6
Remove CAN adapter board from anti-static bag making
sure to handle adapter board by the edges.
Make sure not to bend pins.
Make sure no jumpers or
components on circuit board
are touching adapter board or
are loose that could cause a short.
!
CAUTION
STEP 8
Replace back cover, batteries and battery cover in
reverse order they were removed. Install software as
shown on other side of page.
Do not overtighten phillips screws.
!
CAUTION
Bent Pins
STEP 4
Remove jumpers from circuit board inside Scan Tool.
Remove 14 Jumpers
Remove 1 Jumper
DO NOT Remove Jumpers
STEP 2
Remove 1 phillips screw and 6 AAA batteries.
STEP 3
Remove 6 phillips screws from back cover using a #1
screwdriver.
READ AND UNDERSTAND BEFORE
INSTALLING. IF THERE ARE ANY
QUESTIONS CALL 1-800-228-7667
IMPORTANT
Remove 1 Jumper
STEP 7
Place CAN adapter board on Scan Tool circuit board
pins. DO NOT push adapter board down. Check that
all pins are aligned with connectors on adapter
board. Then gently and evenly push CAN adapter
board at the pressure points indicated onto Scan
Tool circuit board until completely down.
When working with circuit boards
make sure to avoid touching internal
components.
!
CAUTION
Small needle nose pliers (not included)
may be helpful to remove jumpers.
When removing jumpers metal
contacts could fall out causing a
short.
IMPORTANT
If required bend test point and
transistor so that they do not
touch adapter board due to the
chances of a short. Make sure
not to break leads on
components.
IMPORTANT
Transistor
Test Point
Pressure Points
ENTER
BACK
ON
OFF
ENTER
FUNC
HELP
ENTER
BACK
O
N
O
FF
EN
T
E
R
FUNC
H
E
L
P
Installation of
9640UB Software
Install the CAN Adapter Board before
installing software
After 9640UB CAN Adapter Board
installation, 9640UB software must be
installed for tool to work correctly.
IMPORTANT
STEP 1
Remove software serial number and place on CD in
space provided.
STEP 2
Register Software by calling 1-800-228-7667 and receive
an authorization number.
Authorization Number:
A computer is not required for an
authorization number but a computer,
scan tool serial number and software
serial number are required to update
Scan Tool software.
IMPORTANT
STEP 3
Connect serial cable from serial port on computer to
Scan Tool
.
STEP 4
Press ON/OFF button on Scan Tool then press ENTER
when told.
STEP 6
Close all programs on computer and place CD in drive.
STEP 7
Click Start then Run on computer.
STEP 8
Type X:\setup.exe in open box on computer
and press OK.
X is the CD-ROM drive letter
on your computer.
IMPORTANT
STEP 9
Follow screen prompts on computer to complete
software download.
If downloading process
stops, repeat STEP 5
through STEP 9.
IMPORTANT
Start
Run
Open box
OK button
0002-000-2516
ON/OFF
button
STEP 5
Place scan tool
in Program Mode using the and arrows
and pressing ENTER.
Program
Mode
ENTER
button
© 2003 Actron Manufacturing Company
All rights reserved.
ENTER
button
UP and
DOWN
arrows
M
a
in
M
e
n
u
T
o
o
l
S
e
t
u
p
T
o
o
l
S
e
lf
-
T
e
s
t
2 P
r
o
g
r
a
m
M
o
d
e
Software Serial Number:
Scan Tool Serial Number:
  • Page 1 1
  • Page 2 2

Actron 9640 User manual

Actron
Brand
Actron
Model
9640
Type
User manual
This manual is also suitable for

Actron 9640 is a versatile scan tool that provides comprehensive diagnostic capabilities for various vehicle systems. It enables users to retrieve and interpret diagnostic trouble codes (DTCs), view live data streams, perform actuator tests, and access vehicle-specific information. With its user-friendly interface and wide compatibility with domestic and import vehicles, the Actron 9640 empowers users to diagnose and troubleshoot automotive issues efficiently.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents