Avid Mbox 2 Pro 7.4 Specification

Brand: Avid

Model: Mbox 2 Pro 7.4

Category: Recording Equipment

Type: Specification

This manual is also suitable for

Mbox Pro

Getting Started

Mbox

2 Pro

Version 7.4

Legal Notices

Avid Technology, Inc. (hereafter “Digidesign”), with all rights

reserved. Under copyright laws, this guide may not be

duplicated in whole or in part without the written consent of

Digidesign.

003, 003 Rack, 96 I/O, 96i I/O, 192 Digital I/O, 192 I/O,

888|24 I/O, 882|20 I/O, 1622 I/O, 24-Bit ADAT Bridge I/O,

AudioSuite, Avid, Avid DNA, Avid Mojo, Avid Unity, Avid Unity

ISIS, Avid Unity MediaNetwork, Avid Xpress, AVoption,

AVoption|V10, Beat Detective, Bruno, Command|8, Control|24,

D-Command, D-Control, D-Fi, D-fx, D-Show, DAE, Digi 002,

Digi 002 Rack, DigiBase, DigiDelivery, Digidesign, Digidesign

Audio Engine, Digidesign Intelligent Noise Reduction,

Digidesign TDM Bus, DigiDrive, DigiRack, DigiTest,

DigiTranslator, DINR, DV Toolkit, EditPack, Impact, Interplay,

M-Audio, MachineControl, Maxim, Mbox, MediaComposer,

MIDI I/O, MIX, MultiShell, OMF, OMF Interchange, PRE,

ProControl, Pro Tools M-Powered, Pro Tools, Pro Tools|HD,

Pro Tools LE, QuickPunch, Reel Tape, Reso, Reverb One,

ReVibe, RTAS, Smack!, SoundReplacer, Sound Designer II,

Strike, Structure, SYNC HD, SYNC I/O, Synchronic, TL Space,

Velvet, and X-Form are trademarks or registered trademarks of

Digidesign and/or Avid Technology, Inc. All other trademarks

are the property of their respective owners.

Product features, specifications, system requirements, and

availability are subject to change without notice.

PN 9320-56828-00 REV A 7/07

Comments or suggestions regarding our documentation?

email: [email protected]

Communications and Safety Regulation Information

Compliance Statement

This model Digidesign Mbox 2 Pro complies with the following

standards regulating interference and EMC:

• FCC Part 15 Class B

• EN 55022 Class B

• EN 55204 Class B

• AS/NZS 3548 Class B

• CISPR 22 Class B

Radio and Television Interference

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules.

DECLARATION OF CONFORMITY

We Digidesign,

2001 Junipero Serra Boulevard, Suite 200

Daly City, CA 94014 USA

tel: 650-731-6300

declare under our sole responsibility that the product

Mbox 2 Pro

complies with Part 15 of FCC Rules.

Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

Communication Statement

NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try and correct the interference by one or

more of the following measures:

• Reorient or locate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Any modifications to the unit, unless expressly approved by

Digidesign, could void the user's authority to operate the

equipment.

Canadian Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-

003.

Cet appareil numérique de la classe B est conforme à la norme

NMB-003 du Canada.

Australian Compliance

European Compliance

Digidesign is authorized to apply the CE (Conformité

Europénne) mark on this compliant equipment thereby

declaring conformity to EMC Directive 89/336/EEC and Low

Voltage Directive 73/23/EEC.

Safety Statement

This equipment has been tested to comply with USA and

Canadian safety certification in accordance with the

specifications of UL Standards: UL60065 7th /IEC 60065 7th

and Canadian CAN/CSA C22.2 60065:03. Digidesign Inc., has

been authorized to apply the appropriate UL & CUL mark on its

compliant equipment.

Warning

Mbox 2 Pro

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and

a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the

obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Unplug this apparatus during lightning storms or when

unused for long periods of time.

13) Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped.

14) The apparatus shall not be exposed to dripping or

splashing and no objects filed with liquids (such as vases)

shall be placed on the apparatus.

Warning!

To reduce the risk of fire or electric shock, do not

expose this apparatus to rain or mositure.

Contents

vii

contents

Chapter 1. Installation QuickStart

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Windows Installation Overview

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Mac Installation Overview

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Chapter 2. Welcome to Mbox 2 Pro

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Mbox 2 Pro Package

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Mbox 2 Pro Features

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Pro Tools LE Capabilities

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

System Requirements

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Digidesign Registration

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

About the Pro Tools Guides

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

About www.digidesign.com

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 3. Installing Pro Tools on Windows

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installation Overview

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting Mbox 2 Pro and Installing Pro Tools LE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Launching Pro Tools LE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Additional Software on the Pro Tools Installer Disc

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Uninstalling Pro Tools LE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 4. Installing Pro Tools on Mac

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Installation Overview

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Installing Pro Tools LE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting Mbox 2 Pro to the Computer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Launching Pro Tools LE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Additional Software on the Pro Tools Installer Disc

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Uninstalling Pro Tools

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Mbox 2 Pro Getting Started

viii

Chapter 5. Configuring Your Pro Tools System

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Starting Up or Shutting Down Your System

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Configuring Pro Tools LE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Optimizing a Windows System for Pro Tools

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Optimizing a Mac System for Pro Tools

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Chapter 6. Hardware Overview

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Mbox 2 Pro Front Panel Features

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Mbox 2 Pro Back Panel Features

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Chapter 7. Making Studio Connections

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Connecting Headphones

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Connecting a Sound System

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Connecting Audio Inputs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Connecting a Microphone

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Connecting Instruments to the Mbox 2 Pro

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

MIDI Connections

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Word Clock

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Using a Footswitch

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Chapter 8. Common Tasks with Pro Tools LE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Recording a Pro Tools Session

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Importing Audio from a CD

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Creating an Audio CD from a Pro Tools Session

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Recording MIDI in a Pro Tools Session

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Appendix A. Configuring MIDI Studio Setup (Windows Only)

. . . . . . . . . . . . . . . . . . . . 55

MIDI Studio Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

MIDI Patch Name Support

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Appendix B. Configuring AMS (Mac OS X Only)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Audio MIDI Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

MIDI Patch Name Support

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Contents

Appendix C. Hard Drive Configuration and Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . 63

Avoid Recording to the System Drive

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Supported Drive Formats and Drive Types

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Formatting an Audio Drive

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Partitioning Drives

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Defragmenting an Audio Drive

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Using Mac Drives on Windows Systems

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Hard Disk Storage Space

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Appendix D. Troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Backing Up Your Work

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Common Issues

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Performance Factors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Before You Call Digidesign Technical Support

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Index

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Mbox 2 Pro Getting Started

Chapter 1: Installation QuickStart

chapter 1

Installation QuickStart

Windows Installation

Overview

(Windows Systems Only)

Installing Pro Tools LE™ for Mbox® 2 Pro on a

Windows computer includes the following

steps:

“Connecting Mbox 2 Pro and Installing

Pro Tools LE” on page 9.

“Launching Pro Tools LE” on page 11.

Conﬁguring your system for improved perfor-

mance. (See Chapter 5, “Conﬁguring Your

Pro Tools System.”)

“Making Studio Connections” on page 35.

Mac Installation Overview

(Mac OS X Systems Only)

Installation of Pro Tools LE for Mbox 2 Pro on a

Mac includes the following steps:

“Connecting Mbox 2 Pro to the Computer”

on page 14.

“Installing Pro Tools LE” on page 13.

“Launching Pro Tools LE” on page 14.

Conﬁguring your system for improved perfor-

mance. (See Chapter 5, “Conﬁguring Your

Pro Tools System.”)

“Making Studio Connections” on page 35.

Your authorization code is located on the

inside cover of this guide.

Your authorization code is located on the

inside cover of this guide.

Mbox 2 Pro Getting Started

Chapter 2: Welcome to Mbox 2 Pro

chapter 2

Welcome to Mbox 2 Pro

Welcome to the Mbox

2 Pro portable

Pro Tools

micro-studio from Digidesign

Mbox 2 Pro provides your Firewire-equipped

computer with four channels of analog audio in-

put, six channels of analog audio output, two

channels of digital audio input and output,

MIDI In and Out ports, two channels of analog

monitor output, and two headphone outputs

with front panel level control. Mbox 2 Pro pro-

vides professional-quality mic preamps and 24-

bit analog-to-digital and digital-to-analog con-

verters.

Mbox 2 Pro Package

The Mbox 2 Pro package includes the following:

• Mbox 2 Pro desktop audio interface and

power adapter

• Pro Tools Installer disc containing

Pro Tools LE™ software, DigiRack RTAS (Real-

Time AudioSuite) and AudioSuite plug-ins,

optional software, and electronic PDF guides

• This

Getting Started Guide

, covering installa-

tion, conﬁguration, and common tasks for

your Pro Tools system.

• Firewire connector cable (six-pin 1394)

• Power supply

• Digidesign Registration Information Card

Mbox 2 Pro Features

The Mbox 2 Pro provides the following:

Audio Inputs and Outputs

Mbox 2 Pro lets your Pro Tools LE sessions uti-

lize up to six discrete channels of input and up

to eight discrete channels of output, using the

following analog and digital I/O:

Analog Inputs

• Two channels of analog audio input with

microphone preamps and switchable 48V

phantom power. These analog input jacks

include one XLR/TRS combo connector on

the back panel, and two 1/4-inch DI con-

nectors with switchable Mic and DI source

selection and LEDs on the front panel. A

–20 dB pad is also available separately on

each analog input channel

• Two additional channels of analog audio

input for Line and Phono sources (RIAA)

Analog Outputs

• Two 1/4-inch TRS analog Monitor outputs

• Four additional 1/4-inch balanced analog

line outputs

• Two additional channels of unbalanced

outputs on a single 1/4-inch TRS connector

Mbox 2 Pro Getting Started4

Digital I/O

• Two channels of S/PDIF digital input and out-

put. S/PDIF inputs are available independent

of, and in addition to, analog inputs 1–4

when clocking to S/PDIF. S/PDIF outputs are

always available in Pro Tools

MIDI

• One MIDI In and one MIDI Out port, provid-

ing 16 MIDI input channels and 16 MIDI out-

put channels

Other Capabilities and Speciﬁcations

• 24-bit A/D and D/A converters, supporting

sample rates of 44.1 kHz, 48 kHz, 88.2 kHz

and 96 kHz

• Low latency analog record monitoring

• Two 1/4-inch (TRS) stereo headphone outputs

(A and B) with adjustable level controls. Head-

phones B can mirror A (output channels 1–2)

or be switched to output channels 3–4

• Footswitch jack for starting or stopping play-

back or punching in and out while recording.

Pro Tools LE Capabilities

Pro Tools LE on Windows or Mac provides the

following capabilities with Mbox 2 Pro:

• Playback of up to 32 mono (or 16 stereo)

digital audio tracks, or a combination of

playing back and recording up to 32 mono

(or 16 stereo) digital audio tracks, depend-

ing on your computer’s capabilities

• Up to 128 audio tracks (with 32 voiceable

tracks maximum), 128 Auxiliary Input

tracks, 64 Master Fader tracks, 256 MIDI

tracks, and 32 Instrument tracks per session

• 16-bit or 24-bit audio resolution, at sample

rates up to 96 kHz

• Nondestructive, random-access editing and

mix automation

• Audio processing with up to 5 RTAS plug-

ins per track, depending on your com-

puter’s capabilities

• Up to 5 hardware inserts per track

• Up to 10 sends per track

• Up to 32 internal mix busses

Pro Tools LE uses your computer’s CPU to

mix and process audio tracks (host process-

ing). Computers with faster clock speeds

yield higher track counts and more plug-in

processing.

Chapter 2: Welcome to Mbox 2 Pro 5

System Requirements

Mbox 2 Pro can be used with a Digidesign-qual-

ified Windows or Mac computer.

A DVD drive is required to use the Pro Tools In-

staller disc.

For complete system requirements, visit the

Digidesign website (www.digidesign.com).

Compatibility Information

Digidesign can only assure compatibility and

provide support for hardware and software it has

tested and approved.

For a list of Digidesign-qualified computers, op-

erating systems, hard drives, and third-party de-

vices, visit the Digidesign website

(www.digidesign.com).

MIDI Requirements

Mbox 2 Pro includes one MIDI In port and one

MIDI Out port, providing 16 channels of MIDI

input and 16 channels of MIDI output.

If you require additional MIDI ports, add a MIDI

interface to your system. USB MIDI interfaces

work effectively with Pro Tools systems on Win-

dows or Mac. Serial MIDI interfaces are sup-

ported on Windows systems only.

For a list of supported adapters, visit the Digide-

sign website (www.digidesign.com).

Hard Drive Requirements

For optimal audio recording and playback, all

Pro Tools systems require one or more Digide-

sign-qualified drives.

For a list of Digidesign-qualified hard drives,

visit the Digidesign website

(www.digidesign.com).

If you are using an ATA/IDE or FireWire hard

drive, initialize your drive with Windows Disk

Management (Windows) or the Disk Utility ap-

plication included with Apple System software

(Mac).

Avoid Recording to the System Drive

Recording to your system drive is not recom-

mended. Recording and playback on a system

drive may result in lower track counts and fewer

plug-ins.

Digidesign Registration

Review the enclosed Digidesign Registration In-

formation Card and follow the instructions on it

to quickly register your purchase online. This is

one of the most important steps you can take as

a new user. Registering your purchase is the only

way you can be eligible to receive:

• Complimentary technical support

• An update to the latest version of Pro Tools

at no charge if you bought a system with

older software in the box

• Future upgrade offers

Only USB MIDI interfaces are compatible

with Pro Tools systems for Mac OS X.

Modem-to-serial port adapters and serial

MIDI devices are not supported.

For more information, see Appendix C,

“Hard Drive Configuration and Mainte-

nance.”

Digidesign does not recommend recording

to the system drive. Record to a system drive

only when necessary.

Mbox 2 Pro Getting Started6

About the Pro Tools Guides

This Getting Started guide explains how to in-

stall Pro Tools LE software, make basic connec-

tions to your Mbox 2 Pro interface (to get sound

in and out of your interface), and do common

tasks (such as recording in Pro Tools).

In addition to any printed guides or documenta-

tion included with your system, PDF versions of

Pro Tools guides and Read Mes are installed au-

tomatically with Pro Tools.

The main guides (such as the Pro Tools Reference

Guide and the Pro Tools Menus Guide) are accessi-

ble from the Pro Tools Help menu.

• Pro Tools Reference Guide explains Pro Tools

software in detail.

• Pro Tools Menus Guide covers all the Pro Tools

on-screen menus.

• DigiRack Plug-ins Guide explains how to use

the RTAS and AudioSuite plug-ins included

with Pro Tools.

• Digidesign Plug-ins Guide explains how to use

optional Digidesign plug-ins.

• Pro Tools Shortcuts lists keyboard and Right-

click shortcuts for Pro Tools.

These guides and other guides are installed on

your startup drive during installation. To view

or print PDF guides, you can use Adobe Reader

or Apple Preview (Mac only).

Conventions Used in This Guide

Digidesign guides use the following conven-

tions to indicate menu choices and key com-

mands:

The following symbols are used to highlight im-

portant information:

Printed copies of the Pro Tools Reference

Guide and other guides in the Pro Tools

guide set can be purchased separately from

the DigiStore (www.digidesign.com).

Convention Action

File > Save Choose Save from the File

Control+N Hold down the Control key

and press the N key

Control-click Hold down the Control key

and click the mouse button

Right-click Click with the right mouse

button

User Tips are helpful hints for getting the

most from your Pro Tools system.

Important Notices include information that

could affect your data or the performance of

your system.

Shortcuts show you useful keyboard or

mouse shortcuts.

Cross References point to related sections in

other guides.

Chapter 2: Welcome to Mbox 2 Pro 7

About www.digidesign.com

The Digidesign website (www.digidesign.com) is

your best source for information to help you get

the most out of your Pro Tools system. The fol-

lowing are just a few of the services and features

available.

Product Registration Register your purchase on-

line. See the enclosed Digidesign Registration

Information Card for instructions.

Support and Downloads Contact Digidesign

Technical Support or Customer Service; down-

load software updates and the latest online

manuals; browse the Compatibility documents

for system requirements; search the online An-

swerbase; join the worldwide Pro Tools commu-

nity on the Digidesign User Conference.

Training and Education Become a certified

Pro Tools Operator or Expert; study on your

own using courses available online, or find out

how you can learn in a classroom setting at a

certified Pro Tools Training Center.

Products and Developers Learn about Digidesign

products; download demo software; learn about

our Development Partners and their plug-ins,

applications, and hardware.

News and Events Get the latest news from

Digidesign; sign up for a Pro Tools demo.

To learn more about these and other resources

available from Digidesign, visit the Digidesign

website (www.digidesign.com).

Mbox 2 Pro Getting Started8

Chapter 3: Installing Pro Tools on Windows 9

chapter 3

Installing Pro Tools on Windows

This chapter contains information for Windows

systems only. If you are installing Pro Tools on a

Mac computer, see Chapter 4, “Installing

Pro Tools on Mac.”

Installation Overview

Installing the Mbox 2 Pro on a Windows com-

puter includes the following steps:

1 “Connecting Mbox 2 Pro and Installing

Pro Tools LE” on page 9.

2 “Launching Pro Tools LE” on page 11.

3 Conﬁguring your system for improved perfor-

mance. (See Chapter 5, “Conﬁguring Your

Pro Tools System.”)

4 Making audio and MIDI connections to the

Mbox 2 Pro. (See Chapter 7, “Making Studio

Connections” for details.)

Connecting Mbox 2 Pro and

Installing Pro Tools LE

To install Pro Tools LE and Mbox 2 Pro:

1 Start Windows, logging in with Administrator

privileges. For details on Administrator privi-

leges, refer to your Windows documentation.

2 Connect one end of the included Firewire ca-

ble to one of the Firewire ports on Mbox 2 Pro.

3 Connect the other end of the cable to any

available Firewire (6-pin 1394) port on your

computer. Wait for the Found New Hardware

Wizard dialog to appear and leave it open: Do

not click Next. If the Wizard begins to install

drivers automatically, press Cancel.

4 Insert the Pro Tools LE Installer disc for Win-

dows in your CD/DVD drive.

5 On the Installer disc, locate and open the

Pro Tools Installer folder.

6 Double-click the Setup icon.

7 Follow the on-screen instructions to proceed

with installation.

8 Select the install location. For maximum reli-

ability, install Pro Tools on your startup drive.

Before installing this version of Pro Tools,

refer to the Read Me information included

on the Pro Tools Installer disc.

Throughout the installation, you should ig-

nore all Found New Hardware Wizard dia-

logs. Do not click Next.

Mbox 2 Pro Getting Started10

9 Click Next.

10 Select the Pro Tools application for installa-

tion.

11 You can also select from a list of optional

items to install along with Pro Tools.

Mac HFS+ Disk Support Option This option lets

your Pro Tools system read, write, record, and

play back using Mac-formatted HFS+ disks. HFS+

disks are commonly referred to as Mac OS Ex-

tended disks.

DigiTranslator DigiTranslator™ is a software op-

tion for Pro Tools that lets you convert and ex-

change OMF and AAF sequences and MXF files

directly in the Pro Tools application. This op-

tion is purchased separately.

Command|8 Controller and Driver The Com-

mand|8 Driver is required if you are using the

Digidesign Command|8 control surface.

MP3 Export Option The MP3 Export Option lets

you export MP3 files from Pro Tools. This op-

tion is purchased separately.

12 Click Next.

13 Click Install.

14 Wait for the installer to ﬁnish installing all

software components, drivers, and PACE System

ﬁles before proceeding to the next step.

15 When installation is complete, click Finish.

Installing QuickTime

QuickTime is required for Pro Tools if you plan

to include movie files, or import MP3 or MP4

(AAC) files in your sessions. QuickTime for Win-

dows XP is available as a free download from the

Apple website (www.apple.com).

To install QuickTime:

1 Visit www.apple.com and go to the Quick-

Time page.

2 Download the QuickTime installer applica-

tion to your computer.

3 Double-click the QuickTime installer applica-

tion and follow the on-screen installation in-

structions.

The Pro Tools Installer disc includes addi-

tional software for your system. For more

information, see “Additional Software on

the Pro Tools Installer Disc” on page 11.

On Windows XP, several messages are dis-

played during installation that can be ig-

nored, including multiple “Found New

Hardware” dialogs and “A Problem Oc-

curred During Hardware Installation.”

Additionally, if you get a warning dialog

about the driver not passing Windows Logo

testing, click Continue Anyway.

On Windows Vista, if you get a warning di-

alog about the driver, click “Install this

Driver Anyway!”

For information on which version of Quick-

Time is compatible with your version of

Pro Tools, visit the compatibility pages of

the Digidesign website

(www.digidesign.com).

Chapter 3: Installing Pro Tools on Windows 11

4 Restart your computer.

Disabling Screen Saver

(Windows Vista Only)

To avoid errors during recording and playback

of Pro Tools sessions, you must set your Win-

dows Vista screen saver to “None.”

To set your Windows Vista screen saver to “None”:

1 Right-click on the desktop.

2 Choose Personalize.

3 Click Screen Save.

4 Set the Screen saver to None.

5 Click Apply.

Launching Pro Tools LE

When launching Pro Tools LE the first time, you

are prompted to enter an authorization code.

To authorize Pro Tools LE software:

1 Make sure Mbox 2 Pro is connected to your

computer and powered on.

2 Double-click the Pro Tools LE shortcut on

your desktop (or the application icon in the

Pro Tools folder inside the Digidesign folder).

3 Enter the authorization code in the dialog

(making sure to type it exactly as printed, and

observing any spaces and capitalization), then

click Validate.

Your authorization code is located on the inside

front cover of this guide.

Additional Software on the

Pro Tools Installer Disc

The Pro Tools Installer disc provides additional

software for your system, including audio driv-

ers (for playing other audio applications

through your Digidesign hardware) and a

Pro Tools demo session.

Windows Audio Drivers

The Mbox 2 Pro ASIO Driver and DirectSound

Window System Audio Driver let you use your

Digidesign Mbox 2 Pro hardware interface with

third-party applications that support the ASIO

Driver or DirectSound Driver standard.

The Mbox 2 Pro ASIO Driver and DirectSound

Driver for Mbox 2 Pro are automatically in-

stalled when you install Pro Tools.

Mbox 2 Pro ASIO Driver

The Mbox 2 Pro ASIO (Audio Sound Input Out-

put) Driver is a single-client multichannel

sound driver that allows third-party audio pro-

grams that support the ASIO Driver standard to

record and play back through Mbox 2 Pro.

Refer to your Pro Tools Installer disc for ad-

ditional software and installers.

For detailed information on configuring the

Digidesign ASIO Driver, see the Windows

Audio Drivers Guide.

Mbox 2 Pro Getting Started12

DirectSound Windows System Audio Driver

The DirectSound Windows System Audio Driver

is a multi-client, multichannel sound driver that

allows third-party audio programs that support

the DirectSound standard to play back and

record through Mbox 2 Pro.

Standalone Windows Audio Drivers

Digidesign Windows Audio Drivers can be in-

stalled on Windows systems that do not have

Pro Tools software installed. Use the standalone

version of the Digidesign Windows Audio Driv-

ers installer (Digidesign Audio Drivers

Setup.exe), which is available on the Pro Tools

Installer disc.

Pro Tools Demo Session

The Pro Tools LE Installer disc includes a demo

session that you can use to verify that your sys-

tem is working.

The demo session for Pro Tool LE is named “Fil-

tered Dreams.”

To install the demo session:

1 Insert the Pro Tools LE Installer disc into your

CD/DVD drive.

2 From your CD/DVD drive, locate and open

the Additional Files/Pro Tools LE Demo Session

Installer folder.

3 Double-click Setup.exe.

4 Select your audio drive as the install location

and click Install.

5 When installation is complete, click OK.

Uninstalling Pro Tools LE

If you need to uninstall Pro Tools software from

your computer, you can use Windows com-

mands for uninstalling programs.

To uninstall Pro Tools from your computer

(Windows Vista):

1 Choose Start > Control Panel.

2 Under Programs, click “Uninstall a program.”

3 Select Pro Tools.

4 Click Uninstall.

5 Follow the on-screen instructions to remove

Pro Tools.

To uninstall Pro Tools from your computer

(Windows XP):

1 Choose Start > Control Panel.

2 Double-click Add or Remove Programs.

3 From the Currently Installed Programs list, se-

lect Digidesign Pro Tools.

4 Click the Remove button.

5 Follow the on-screen instructions to remove

Pro Tools.

For detailed information on configuring the

Digidesign DirectSound Driver, see the

Windows Audio Drivers Guide.

For information on installing and configur-

ing the standalone version of the Digidesign

Windows Audio Drivers, see the Windows

Audio Drivers Guide.

Before installing the demo session to your

audio drive, make sure the drive is config-

ured as described in “Formatting an Audio

Drive” on page 64.

The demo session can be opened by double-

clicking the Filtered Dream.ptf file (located

in the Filtered Dream Demo Session folder).

Page is loading ...

Avid Mbox 2 Pro 7.4 Specification

Brand: Avid

Model: Mbox 2 Pro 7.4

Category: Recording Equipment

Type: Specification

This manual is also suitable for

Mbox Pro

Download PDF

report

Avid Mbox 2 Pro 7.4 Specification

This manual is also suitable for

Avid Mbox 2 Pro 7.4 Specification

Related papers

Other documents