Cisco Systems UCSEZINFRACHSS User manual

Brand: Cisco Systems

Model: UCSEZINFRACHSS

Category: Servers

Type: User manual

Cisco UCS 5108 Server Chassis Installation Guide

First Published: June 10, 2009

Last Modified: October 08, 2013

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Text Part Number: OL-20035-05

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH

THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15

of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are

encouraged to try to correct the interference by using one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version

1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS.

CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network

topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional

and coincidental.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://

www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership

relationship between Cisco and any other company. (1110R)

CONTENTS

Preface

Preface ix

Audience ix

Conventions ix

Related Cisco UCS Documentation xi

Obtaining Documentation and Submitting a Service Request xi

CHAPTER 1

Overview 1

System Overview 1

Features and Benefits 2

Components 4

Cisco UCS 5108 Server Chassis 4

LEDs 4

Buttons 4

Connectors 4

Midplane 4

Blade Servers 5

Cisco UCS B200 Blade Servers 5

LEDs 6

Buttons 6

Connectors 6

Cisco UCS B200 M3 Blade Servers 7

LEDs 7

Buttons 7

Connectors 8

Cisco UCS B22 M3 Blade Servers 8

LEDs 8

Buttons 9

Cisco UCS 5108 Server Chassis Installation Guide

OL-20035-05 iii

Connectors 9

Cisco UCS B230 Blade Servers 9

LEDs 10

Buttons 10

Connectors 10

Cisco UCS B250 Blade Servers 11

LEDs 11

Buttons 11

Connectors 12

Cisco UCS B440 Blade Servers 12

LEDs 12

Buttons 13

Connectors 13

Cisco UCS B420 M3 High Performance Blade Server 13

LEDs 14

Buttons 14

Connectors 14

Adapter Cards 14

Cisco UCS Virtual Interface Card 1280 14

Cisco UCS M81KR Virtual Interface Card 14

Cisco UCS 82598KR-CI 10 Gigabit Ethernet Adapter 15

Cisco UCS M71KR-E Emulex Converged Network Adapter 15

Cisco UCS M71KR-Q QLogic Converged Network Adapter 16

Cisco UCS 2104XP FEXes 17

LEDs 18

Buttons 18

Connectors 18

Cisco UCS 2200 Series FEXes 18

LEDs 20

Buttons 20

Connectors 20

Power Distribution Unit (PDU) 20

LEDs 20

Buttons 20

Connectors 20

Cisco UCS 5108 Server Chassis Installation Guide

iv OL-20035-05

Contents

Fan Modules 21

LEDs 21

Buttons and Connectors 21

Power Supplies 21

LEDs 21

Buttons 21

Connectors 21

Power Supply Redundancy 21

Non-redundant Mode 22

N+1 Redundancy 22

Grid Redundancy 23

LEDs 23

LED Locations 24

Interpreting LEDs 25

CHAPTER 2

Installation 29

Installation Notes and Warnings for the Cisco UCS 5108 Server Chassis 29

Rack Requirements 30

Cable Management 30

Airflow Considerations 31

Moving Server Chassis 32

Installation Guidelines 32

Required Equipment 33

Unpacking and Inspecting the Chassis 33

Attaching the Round Hole Adapter Kit to the Rails (Optional) 34

Installing the Chassis 35

Installing the Rails 36

Installing the Round Hole Adapter Kit 39

Inserting the Chassis into the Rack 42

Connecting a DC Power Supply 44

Required Tools 44

DC Power Installation Procedure 44

Cabling Considerations for Fabric Port Channels 47

Proper FEX and Fabric Interconnect Port Connectivity 48

Removing the Chassis from a Rack 50

Cisco UCS 5108 Server Chassis Installation Guide

OL-20035-05 v

Contents

Repacking the Chassis 51

SFP+ Transceivers 51

SFP+ Twinax Copper Transceivers 51

Optical SFP+ Transceivers 52

Replacing a Copper Twinax SFP+ Transceiver with an Optical SFP+ Transceiver 53

CHAPTER 3

Installing and Removing Components 55

Components 55

Installing and Removing a Blade Server 57

Installing and Removing a Blade Server Hard Drive 57

Installing a Blade Server Hard Drive 58

Removing a Blade Server Hard Drive 59

Installing and Removing Power Supplies 59

Installing a Power Supply 60

Removing a Power Supply 61

Installing and Removing a Power Distribution Unit (PDU) 62

Installing a PDU 62

Removing a PDU 63

Installing and Removing FEXes 63

FEX Upgrade Considerations 63

Removing a FEX 64

Installing a FEX 65

Installing and Removing a Fan Module 66

Installing a Fan Module 66

Removing a Fan Module 67

APPENDIX A

Technical Specifications 69

KVM Cable 69

Chassis Specifications 70

Environmental Specifications 71

Environmental Conditions and Power Requirement Specifications for Twinax SFP+

Transceivers 71

Specifications for the Cisco UCS 5108 Blade Server Chassis Power Supply Units 72

Supported AC Power Cords and Plugs 74

Australia and New Zealand 74

Cisco UCS 5108 Server Chassis Installation Guide

vi OL-20035-05

Contents

Continental Europe 75

International 75

Israel 75

Japan and North America 76

Peoples Republic of China 77

Switzerland 77

Power Distribution Unit (PDU) 78

APPENDIX B

Site Planning and Maintenance Records 79

Site Preparation Checklist 79

Contact and Site Information 81

Chassis and Module Information 81

FEX Port Connection Record 83

Cisco UCS 5108 Server Chassis Installation Guide

OL-20035-05 vii

Contents

Cisco UCS 5108 Server Chassis Installation Guide

viii OL-20035-05

Contents

Preface

This preface includes the following sections:

•

Audience, page ix

•

Conventions, page ix

•

Related Cisco UCS Documentation, page xi

•

Obtaining Documentation and Submitting a Service Request, page xi

Audience

To use this installation guide, you must be familiar with electronic circuitry and wiring practices and preferably

be an electronic or electromechanical technician who has experience with electronic and electromechanical

equipment.

Only trained and qualified service personnel (as defined in IEC 60950-1 and AS/NZS60950) should install,

replace, or service the equipment. Install the system in accordance with the U.S. National Electric Code if

you are in the United States.

Conventions

IndicationText Type

GUI elements such as tab titles, area names, and field labels appear in this font.

Main titles such as window, dialog box, and wizard titles appear in this font.

GUI elements

Document titles appear in this font.

Document titles

In a Text-based User Interface, text the system displays appears in this font.TUI elements

Terminal sessions and information that the system displays appear in this

font.

System output

Cisco UCS 5108 Server Chassis Installation Guide

OL-20035-05 ix

IndicationText Type

CLI command keywords appear in this font.

Variables in a CLI command appear in this font.

CLI commands

Elements in square brackets are optional.[ ]

Required alternative keywords are grouped in braces and separated by vertical

bars.

{x | y | z}

Optional alternative keywords are grouped in brackets and separated by vertical

bars.

[x | y | z]

A nonquoted set of characters. Do not use quotation marks around the string or

the string will include the quotation marks.

string

Nonprinting characters such as passwords are in angle brackets.< >

Default responses to system prompts are in square brackets.[ ]

An exclamation point (!) or a pound sign (#) at the beginning of a line of code

indicates a comment line.

!, #

Means reader take note. Notes contain helpful suggestions or references to material not covered in the

document.

Note

Means the following information will help you solve a problem. The tips information might not be

troubleshooting or even an action, but could be useful information, similar to a Timesaver.

Tip

Means reader be careful. In this situation, you might perform an action that could result in equipment

damage or loss of data.

Caution

Means the described action saves time. You can save time by performing the action described in the

paragraph.

Timesaver

Cisco UCS 5108 Server Chassis Installation Guide

x OL-20035-05

Preface

Conventions

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with

standard practices for preventing accidents. Use the statement number provided at the end of each warning

to locate its translation in the translated safety warnings that accompanied this device.

SAVE THESE INSTRUCTIONS

Warning

Related Cisco UCS Documentation

Cisco UCS 5108 Server Chassis Installation Guide

xii OL-20035-05

Preface

Obtaining Documentation and Submitting a Service Request

CHAPTER 1

Overview

This chapter contains the following sections:

•

System Overview, page 1

•

Features and Benefits, page 2

•

Components, page 4

•

LEDs, page 23

System Overview

The Cisco UCS 5108 server chassis and its components are part of the Cisco Unified Computing System

(UCS), which uses the Cisco UCS 5108 server system with the two I/O modules and the Cisco UCS Fabric

Interconnects to provide advanced options and capabilities in server and data management. All servers are

managed via the GUI or CLI with Cisco UCS Manager.

The Cisco UCS 5108 server chassis system consists of the following components:

• Cisco UCS 5108 server chassis–AC version (N20-C6508)

• Cisco UCS 5108 server chassis–DC version (UCSB-5108-DC)

• Cisco UCS 2104XP I/O Module (N20-I6584)—Up to two I/O modules, each providing four ports of

10-Gb Ethernet, Cisco Data Center Ethernet, and Fibre Channel over Ethernet (FCoE) connection to the

fabric interconnect

• Cisco UCS 2208XP I/O Module (UCS-IOM-2208XP)—Up to two I/O modules, each providing eight

universal ports configurable as a 10-Gb Ethernet, Cisco Data Center Ethernet, or Fibre Channel over

Ethernet (FCoE) connection to the fabric interconnect

• Cisco UCS 2204XP I/O Module (UCS-IOM-2204XP)—Up to two I/O modules, each providing four

universal ports configurable as a 10-Gb Ethernet, Cisco Data Center Ethernet, or Fibre Channel over

Ethernet (FCoE) connection to the fabric interconnect

•

A number of SFP+ choices using copper or optical fiber

• Power supplies (N20-PAC5-2500W, UCSB-PSU-2500ACPL or N20-DC-2500)—Up to four 2500 Watt

hot-swappable power supplies

Cisco UCS 5108 Server Chassis Installation Guide

OL-20035-05 1

• Fan modules (N20-FAN5)—Eight hot-swappable fan modules

•

UCS B-series blade servers, including

◦ Cisco UCS B200 blade servers (N20-B6620-1 for M1 or N20-B6625-1 for M2)—Up to eight

half-width blade servers, each containing two CPUs and holding up to two hard drives capable of

RAID 0 or 1

◦ Cisco UCS B200 M3 blade servers (UCSB-B200-M3)—Up to eight half-width blade servers, each

containing two CPUs and holding up to two hard drives capable of RAID 0 or 1

◦ Cisco UCS B22 blade servers (UCSB-B22-M3)—Up to eight half-width blade servers, each

containing two CPUs and holding up to two hard drives capable of RAID 0 or 1

◦ Cisco UCS B230 blade servers (N20-B6730)—Up to eight half-width blade servers, each containing

two CPUs and holding up to two SDD drives capable of RAID 0 or 1

◦ Cisco UCS B250 blade servers (N20-B6620-2 for M1 or N20-B6625-2 for M2)—Up to four

full-width blade servers, each containing two CPUs and holding up to two hard drives capable of

RAID 0 or 1

◦ Cisco UCS B440 blade servers (N20-B6740-2)—Up to four full-width blade servers, each containing

four CPUs and holding up to four hard drives capable of RAID 0, 1, 5, and 6

◦ Cisco UCS B420 blade servers (UCSB-B420-M3)—Up to four full-width blade servers, each

containing four CPUs and holding up to four hard drives capable of RAID 0, 1, 5, and 10

Features and Benefits

The Cisco UCS 5108 revolutionizes the use and deployment of blade-based systems. By incorporating unified

fabric, integrated, embedded management, and fabric extender technology, the Cisco Unified Computing

System enables the chassis to have fewer physical components, no independent management, and to be more

energy efficient than traditional blade server chassis.

This simplicity eliminates the need for dedicated chassis management and blade switches, reduces cabling,

and enables the Cisco Unified Computing System to scale to 40 chassis without adding complexity. The Cisco

UCS 5108 chassis is a critical component in delivering the Cisco Unified Computing System benefits of data

center simplicity and IT responsiveness.

Table 1: Features and Benefits

BenefitFeature

Reduces total cost of ownership by removing management modules from the

chassis, making the chassis stateless.

Provides a single, highly available management domain for all system chassis,

reducing administrative tasks.

Management by Cisco

UCS Manager

Decreases TCO by reducing the number of network interface cards (NICs), host

bus adapters (HBAs), switches, and cables needed.

Unified fabric

Cisco UCS 5108 Server Chassis Installation Guide

2 OL-20035-05

Overview

Features and Benefits

BenefitFeature

Eliminates switches from the chassis, including the complex configuration and

management of those switches, allowing a system to scale without adding

complexity and cost.

Allows use of two I/O modules for redundancy or aggregation of bandwidth.

Enables bandwidth scaling based on application needs; blades can be configured

from 1.25 Gbps to 40 Gbps or more.

Support for one or two

Cisco UCS 2100 Series

or Cisco UCS 2200

FEXes

Requires no configuration; like all components in the Cisco Unified Computing

System, chassis are automatically recognized and configured by Cisco UCS

Manager.

Auto discovery

Provides investment protection for new fabric extenders and future blade servers.

Supports up to 2x 40 Gigabit Ethernet for every blade server slot when used in

high-availability mode.

Provides 8 blades with 1.2 terabits (Tb) of available Ethernet throughput for future

I/O requirements.

Provides reconfigurable chassis to accommodate a variety of form factors and

functions.

High-performance

midplane

Provides high availability in multiple configurations.

Increases serviceability.

Provides uninterrupted service during maintenance.

Available configured for AC or DC environments (mixing not supported)

Redundant hot

swappable power

supplies and fans

Provides uninterrupted service during maintenance and server deployment.Hot-pluggable blade

servers and FEXes

Provides extensive environmental monitoring on each chassis

Allows use of user thresholds to optimize environmental management of the

chassis.

Comprehensive

monitoring

Helps reduce power consumption and increase component reliability.Efficient front-to-back

airflow

Requires no specialized tools for chassis installation.

Provides mounting rails for easy installation and servicing.

Tool-free installation

Allows up to 8 half-width or 4 full-width blade servers, or any combination

thereof, for outstanding flexibility.

Mixed blade

configurations

Cisco UCS 5108 Server Chassis Installation Guide

OL-20035-05 3

Overview

Features and Benefits

Components

Cisco UCS 5108 Server Chassis

The Cisco UCS 5100 Series Blade Server Chassis is a scalable and flexible blade server chassis for today’s

and tomorrow’s data center that helps reduce total cost of ownership. It is available configured for AC

(N20-C6508) and DC (UCSB-5108-DC) power environments.

Is six rack units (6 RU) high and can mount in an industry-standard 19-inch rack with square holes (such as

the Cisco R Series Racks) or in round hole racks when an adapter is used. The chassis can house up to eight

half-width Cisco UCS B-Series Blade Servers and can accommodate both half- and full-width blade form

factors.

Four single-phase, hot-swappable AC or DC power supplies are accessible from the front of the chassis. These

power supplies can be configured to support nonredundant, N+1 redundant, and grid-redundant configurations.

The rear of the chassis contains eight hot-swappable fans, four power connectors (one per power supply), and

two I/O bays for I/O modules. A passive midplane provides up to an effective maximum of 20 Gbps of I/O

bandwidth per server slot and up to 40 Gbps of I/O bandwidth for two slots, the midplane is built to eventually

support 80 Gbps per slot.

Scalability is dependent on both hardware and software. For more information, see FEX Upgrade

Considerations, on page 63 and the appropriate UCS software release notes.

LEDs

LEDs on the chassis indicate system connectivity and failure warnings. See LED Locations, on page 24 for

details. There is also a flashing blue Beaconing LED and button that can be triggered manually or remotely

from UCS Manager.

Buttons

The beaconing function LED is also a feature on/off button. When triggered, beaconing of the server chassis

is observable remotely from UCS Manager.

Connectors

There are no user connectors such as RJ-45 ports on the chassis itself.

Midplane

The integral chassis midplane supports the following:

•

40 G total bandwidth to each of two I/O Modules

•

Auto-discover of all components

•

Redundant data and management paths

•

10 G Base-KR

Cisco UCS 5108 Server Chassis Installation Guide

4 OL-20035-05

Overview

Components

The midplane is an entirely passive device.

Blade Servers

The Cisco UCS B-Series Blade Servers are based on industry-standard server technologies and provide the

following:

•

Up to two or four Intel multi-core processors, depending on the server

•

Front-accessible, hot-swappable hard drives or solid-state disk (SSD) drives

•

Depending on the server, support is available for up to three adapter card connections for up to 40 Gbps

of redundant I/O throughput

•

Industry-standard double-data-rate 3 (DDR3) memory

•

Remote management through an integrated service processor that also executes policy established in

Cisco UCS Manager software

•

Local keyboard, video, and mouse (KVM) and serial console access through a front console port on

each server

•

Out-of-band access by remote KVM, Secure Shell (SSH), and virtual media (vMedia) as well as Intelligent

Platform Management Interface (IPMI)

The Cisco UCS B-Series offers multiple blade server models. The supported processor family is indicated by

M1, M2, or M3 designations on the model.

Cisco UCS B200 Blade Servers

For full service and installation instructions, see the Cisco UCS B200 Blade Server Installation and Service

Note. You can install up to eight UCS B200 M1 or M2 Blade Servers to a chassis.

Figure 1: Cisco UCS B200 M1 and M2

Network link status LED7Paper tab for server name or serial

numbers

Blade health LED8Blade ejector handle2

Cisco UCS 5108 Server Chassis Installation Guide

OL-20035-05 5

Overview

Blade Servers

Console connector9Ejector captive screw3

Reset button access10Hard drive bay 14

Beaconing LED and button11Hard drive bay 25

Power button and LED6

LEDs

The LED indicators indicate whether the blade server is in active or standby mode, the status of the network

link, the over all health of the blade server, and whether the server is set to give a flashing blue beaconing

indication. See Interpreting LEDs, on page 25 for details.

The removable hard disks also have LEDs indicating hard disk access activity and hard disk health.

Buttons

The Reset button is just inside the chassis and must be pressed using the tip of a paper clip or a similar item.

Hold the button down for five seconds and then release it to restart the server if other methods of restarting

are not working.

The beaconing function for an individual server may get turned on or off by pressing the combination button

and LED. See Interpreting LEDs, on page 25 for details.

The power button and LED allows you to manually take a server temporarily out of service but leave it in a

state where it can be restarted quickly.

Connectors

A console port gives a direct connection to a blade server to allow operating system installation and other

management tasks to be done directly rather than remotely. The port uses the KVM dongle device included

in the chassis accessory kit. See KVM Cable, on page 69 for more information.

Cisco UCS 5108 Server Chassis Installation Guide

6 OL-20035-05

Overview

Blade Servers

Cisco UCS B200 M3 Blade Servers

For full service and installation instructions, see the Cisco UCS B200 M3 Blade Server Installation and Service

Note. You can install up to eight UCS B200 M3 Blade Servers to a chassis.

Figure 2: Cisco UCS B200 M3

Network link status LED7Asset Tag

Blade health LED8Blade ejector handle2

Console connector9Ejector captive screw3

Reset button access10Hard drive bay 14

Beaconing LED and button11Hard drive bay 25

Power button and LED6

Each server has a blank plastic tag that pulls out of the front panel which is provided so that you can add your own asset tracking label without interfering with

the intended air flow.

LEDs

The LED indicators indicate whether the blade server is in active or standby mode, the status of the network

link, the over all health of the blade server, and whether the server is set to give a flashing blue beaconing

indication. See Interpreting LEDs, on page 25 for details.

The removable hard disks also have LEDs indicating hard disk access activity and hard disk health.

Buttons

The Reset button is just inside the chassis and must be pressed using the tip of a paper clip or a similar item.

Hold the button down for five seconds and then release it to restart the server if other methods of restarting

are not working.

The beaconing function for an individual server may get turned on or off by pressing the combination button

and LED. See Interpreting LEDs, on page 25 for details.

Cisco UCS 5108 Server Chassis Installation Guide

OL-20035-05 7

Overview

Blade Servers

The power button and LED allows you to manually take a server temporarily out of service but leave it in a

state where it can be restarted quickly.

Connectors

A console port gives a direct connection to a blade server to allow operating system installation and other

management tasks to be done directly rather than remotely. The port uses the KVM dongle device included

in the chassis accessory kit. See KVM Cable, on page 69 for more information.

Cisco UCS B22 M3 Blade Servers

For full service and installation instructions, see the Cisco UCS B22 Blade Server Installation and Service

Note. You can install up to eight UCS B22 M3 Blade Servers to a chassis.

Figure 3: Cisco UCS B22 M3

Network link status LED7Asset tag

Blade health LED8Blade ejector handle2

Console connector9Ejector captive screw3

Reset button access10Hard drive bay 14

Beaconing LED and button11Hard drive bay 25

Power button and LED6

Each server has a blank plastic asset tag that pulls out of the front panel, provided so you can add your own asset tracking label without interfering with the

intended air flow.

LEDs