The Murphy Door FMALDM36MSLHOS Installation guide

FMALDM36MSLHOS
Brand
The Murphy Door
Model
FMALDM36MSLHOS
Type
Installation guide
FLUSH MOUNT UNASSEMBLED KIT
ASSEMBLY INSTRUCTIONS
MurphyDoor.com888-458-5911
Looking for an installation video?
Scan this code to go directly to our door assembly
support page and view the installation video.
https://www.themurphydoor.com/assembly-video/
Parts List
Countersunk Screw Holes
(8) 7x50mm Conrmat Screws
A
B
C
(6) #6 x 1.5in Square Head Pocket Screws
D
(12) Dowel Pins
E
F
B
(18) 8mm Wood Dowels
G
Jamb Side
Jamb Side
Jamb Top
Jamb Bottom
(Threshold)
JAMB
BOOKCASE
Back
Bookcase Side
Bookcase Side
Top
Bottom
Short Side
Middle
Top
Bottom
Short Side
Middle
Back Top
(Double Thick)
Back Middle
Adjustable Shelf Adjustable Shelf Adjustable Shelf
FACE FRAME
Top
Bottom
Long SideShort Side
Middle
Casing Side
Casing Side
Casing Top
Long Side
Long Side
Back Bottom
(Double Thick)
Bottom
Door Hinge
Bottom
Jamb Hinge
Top Door
Hinge
Top Jamb
Hinge
2 Notches
MurphyDoor.com888-458-5911
NOTE: French Doors will include a longer upper jamb and threshold as
well as a center trim/casing piece.
1
GLUE
X
NO GLUE
D
G
D
Pocket Screw
2
E
(
12
)
Make sure that all screw
placement holes for the
hinges are facing the top
side of the door.
The hinge pass-through
holes are the only thing
that should be visible
from the inside of the
bookshelf.
Dowel Hole
Dowel Hole
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
The dowel holes where you will attach the face
frame are on the front side of each piece. Make
sure that they are all facing outward towards the
front of the door when assembling.
Top shelf will have pre-
drilled hole where you will
drop the hinge pin through.
The bottom shelf does not.
Top
Bottom
Long SideShort Side
Middle
Top
Bottom
Middle
Long Side
Short Side
Top
(Double Thick)
Middle
Bottom
(Double Thick)
Middle
Top
Bottom
Middle
Top
(Enlarged View)
NOTE: The top and bottom book-
shelf pieces are double thick and
the middle piece is just a standard
single thickness.
Assemble Face Frame
Assemble Bookcase
NOTE: Please verify dowel orientation to ensure that they are not installed upside down.
D
(
6
)
G
(
12
)
Dowel holes
toward top
Dowel holes
toward bottom
Dowel holes
toward top
Back
Back
Front
Front
MurphyDoor.com888-458-5911
MurphyDoor.com888-458-5911
C
(
12
)
Line up with middle (xed) shelf
4
3
Set Shelves
Top
Bottom
With the front of the bookcase laying at on the oor, use a rubber mallet and a small piece of wood to tap on each side
until it is ush with the front of the bookcase. This will ensure that the back piece is able to slide completely into place.
Note: The small piece of wood is used to prevent denting or damage to your shelves when setting in place.
The shelves should be ush with
the front of the bookcase when set
properly.
It is recommended that you use two people when placing the back to ensure that it slides
in straight to prevent it from getting wedged from sliding in crooked.
Place Back
Gently push on bookcase frame to square
before fastening the back with screws. Make
sure that the back is ush all the way across the
top and bottom.
Top
Bottom
Long Side
Short Side
Long Side
Short Side
VIEW OF
BACK OF DOOR
Back
Back
Back
Front
Front
Front
UPPER JAMB
FRENCH DOOR UPPER JAMB
You will need to repeat the same process as above for the left and right sides of the upper jamb.
Upper Jamb (French Door)
NOTICE: HINGE TEMPLATES ARE NEEDED FOR HARDWOODS ONLY
Hinges on Right
Hinges on Left
A
Place the template for your desired swing conguration onto the upper jamb. Drill the spots where the screws for the hinges will be located. For
an out-swing conguration you will also need to drill through the entire upper jamb for the hinge pin to be able to pass through.
Paint Grade doors come with the Lower/UpperJamb pre-drilled. To
install the hinges, locate the side with the decal on it and ip it 180
degrees.
PAINT GRADE WITH PRE-DRILLED HOLES
Lower Jamb (Threshold) & Upper Jamb
180˚
Use a nail or similar object to pop out the last
remaining wood until the hole is unblocked.
NOTE: Although not
required, you may use some
small nish nails in addition
to the glue to help secure
the face frame.
Long Side
Short Side
Top
Bottom
MurphyDoor.com888-458-5911
G
(
6
)
5
Fastening Face Frame
Make sure that all dowel
holes are facing the front of
the door.
6
Hinge Templates
MurphyDoor.com888-458-5911
Lower Jamb (Threshold)
FRENCH DOOR
You will need to repeat the same process as above for the left and right sides of the lower jamb (threshold).
Lower Jamb (Threshold)
A
Place the template for your desired swing conguration onto the lower jamb (threshold). Drill the spots where the screws for the hinges will be located.
Hinges on Right
Hinges on Left
C
Rotate upper jamb 180 degrees so the hinge is on the underside of the upper jamb
Top of Jamb
Hinge is now on the underside of the upper jamb
180˚
FRENCH DOOR
You will need to repeat the same process as above for the upper jamb of the french door.
B
Fasten hinge to upper jamb
FRENCH DOOR
You will need to repeat the same process as above for the left and right sides of the upper jamb.
Upper Jamb (French Door)
Upper Jamb (French Door)
180˚
NOTICE: HINGE TEMPLATES ARE NEEDED FOR HARDWOODS ONLY
MurphyDoor.com888-458-5911
7
Assemble Jamb
FRENCH DOOR
The jamb assembly for the French Door, is the exact same process as the Flush Mount door.
The only dierence is the length of the upper jamb and lower jamb (threshold).
B
Fasten hinge to lower jamb (threshold)
FRENCH DOOR
You will need to repeat the same process as above for the left and right sides of the lower jamb (threshold)
Lower Jamb (Threshold)
Lower Jamb (Threshold)
A
(
8
)
The Lower Jamb (Threshold) is wider than the rest of
the jamb. Make sure that it is ush with the front and
extends out the back side.
8
Trim / Casing
Trim/casing needs to overhang the door by 1/2”. This can be adjusted as needed, just make sure that it covers
the gap between the door and jamb.
IN-SWING - Trim/casing will be attached directly to the wall on all sides.
OUT-SWING - The left or right trim piece will need to be attached to the face frame of the door.
French doors will come with an extra trim piece for the center. This piece will be installed onto either the left
of right door. Be sure to cut this piece so it will leave a 1/16” - 1/8” space at the top in order to clear the top
trim when opening and closing the door.
NOTE: See photos on website for example
8
Out-Swing Hinges
Front
Top of Door
Front
Top of Door
Front
Jamb Bottom
(Threshold)
Front
Jamb Bottom
(Threshold)
B B
B
B
These extra pre-drilled holes are only used for in-swing hinge conguration.
These extra pre-drilled holes are only used for in-swing hinge conguration.
OUT-SWING OUT-SWING
LEFT HINGE RIGHT HINGE
MurphyDoor.com888-458-5911
Placing Pin in Upper Hinge
1) Push in button on end of pin 2) Insert pin through hinge plates 3) Release button after pin has cleared both hinge plates 4) Ball bearings will expand to secure pin in place
You may need to punch holes for hinge pin to pass through
8
In-Swing Hinges
Front
Top of Door
Front
Top of Door
Front
Jamb Bottom
(Threshold)
Front
Jamb Bottom
(Threshold)
Pre-drilled pattern with hinge pin pass-through hole are only used for out-swing hinge conguration.
BB
B B
IN-SWING IN-SWING
These extra pre-drilled holes are only used for out-swing hinge conguration.
LEFT HINGE RIGHT HINGE
MurphyDoor.com888-458-5911
OUT SWING
IN SWING
DOOR SIDE
DOOR BACK
DOOR FRONT / FACE FRAME
VIEW OF
DOOR
BOTTOM
DOOR BOTTOM
Hinges on Left
MurphyDoor.com888-458-5911
NOTICE: Due to variations in individual printer settings we cannot
guarantee that the printed template will be scaled properly. Please
use the included measurements to verify proper placement.
OUT SWING
IN SWING
DOOR SIDE
VIEW OF
DOOR
BOTTOM
DOOR BACK
DOOR FRONT / FACE FRAME
DOOR BOTTOM
Hinges on Right
MurphyDoor.com888-458-5911
NOTICE: Due to variations in individual printer settings we cannot
guarantee that the printed template will be scaled properly. Please
use the included measurements to verify proper placement.
4”
PLACE IN FRONT CORNER
IN-SWING
OUT-SWING
UPPER JAMB
HINGE TEMPLATE
MurphyDoor.com888-458-5911
NOTICE: Due to variations in individual printer settings we cannot
guarantee that the printed template will be scaled properly. Please
use the included measurements to verify proper placement.
Top of Jamb
Hinge is now on the underside of the upper jamb
180˚
NOTE: After attaching the hinge to the upper jamb, before assembling the jamb, you must ip
it 180 degrees so that the hinge piece is now on the underside of the upper jamb.
UPPER JAMB HINGE TEMPLATE
Hinges on Right
4”
PLACE IN FRONT CORNER
IN-SWING
OUT-SWING
UPPER JAMB
HINGE TEMPLATE
UPPER JAMB HINGE TEMPLATE
Hinges on Left
MurphyDoor.com888-458-5911
NOTICE: Due to variations in individual printer settings we cannot
guarantee that the printed template will be scaled properly. Please
use the included measurements to verify proper placement.
Top of Jamb
Hinge is now on the underside of the upper jamb
180˚
NOTE: After attaching the hinge to the upper jamb, before assembling the jamb, you must ip
it 180 degrees so that the hinge piece is now on the underside of the upper jamb.
MurphyDoor.com888-458-5911
NOTICE: Due to variations in individual printer settings we cannot
guarantee that the printed template will be scaled properly. Please
use the included measurements to verify proper placement.
THRESHOLD HINGE TEMPLATE
Hinges on Right
PLACE IN FRONT CORNER
4”
IN-SWING
OUT-SWING
THRESHOLD
HINGE TEMPLATE
PLACE IN FRONT CORNER
IN-SWING
OUT-SWING
THRESHOLD
HINGE TEMPLATE
MurphyDoor.com888-458-5911
NOTICE: Due to variations in individual printer settings we cannot
guarantee that the printed template will be scaled properly. Please
use the included measurements to verify proper placement.
THRESHOLD HINGE TEMPLATE
Hinges on Left
Ogden Headquarters
2541 Rulon White Blvd
Ogden, UT 84404
Kentucky Distribution
Center & Showroom
2320 Fortune Dr. #180
Lexington, KY 40509
MurphyDoor.com888-458-5911
FMAM-1.7.3-20170706
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

The Murphy Door FMALDM36MSLHOS Installation guide

FMALDM36MSLHOS
Brand
The Murphy Door
Model
FMALDM36MSLHOS
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents