Silva Exceed 3X User manual

Brand: Silva

Model: Exceed 3X

Type: User manual

This manual is also suitable for

Exceed 3XT

Page is loading ...

Visit: www.silva/environment

for more information about the

Waste Electrical and Electronic

Equipment (WEEE) Directive.

PRODUCT OVERVIEW

The Exceed 3 packaging contains the following parts:

• Lamp unit

• Headband

• Headband (top)

• Extension cord with helmet strap

• Cable guide (side)

• Cable guide (rear)

• Rechargeable Li-ion battery

• USB charging cable

• USB charger (Exceed 3XT only)

• Helmet bracket

• Bike handle bar bracket

• Quick guide

• Storage bag

BEFORE USE

BATTERY CHARGING

The battery needs to be charged before ﬁrst use.

1. Connect the battery to a USB-port (either from a computer, car or a USB charger/adapter)

using the included USB-charge cable.

2. Connect the charger to the wall outlet.

3. On the battery, there are 5 LEDs showing battery status during charging:

• Green light (all 5 LEDs) = battery is fully charged

• Red light blinking = battery is charging

Note! When the battery is fully charged the charger automatically switches to maintenance

mode.

Note! Never leave a battery unattended during charging.

Exceed 3 is compatible with all Silva batteries with the same connector as on Exceed 3 bat-

tery. Note that the battery indication may not be accurate with other Silva batteries.

SILVA EXCEED 3 – THE FLEXIBLE, MODULAR HEADLAMP

Exceed 3 is designed for Multi-activity Sports. Here is a description of the dierent options:

ERGONOMIC HEADSET

The head set is ergonomically shaped to give comfortable ﬁt. Use the 2 buckle adjustments

to ﬁt it perfectly to your head. Detachable top band included.

Attach the headlamp in the head bracket by sliding the headlamp foot into the snap-in

socket. To remove, slide the headlamp up and out of the bracket.

FLEXIBLE BATTERY CARRYING

The battery pack can be carried in multiple ways; for example on the headband, in a pocket

backpack, on the waist using the extension cable and cable guide back, or mounted on the

bike frame by using the integrated Velcro strap.

The ergonomic back plate is designed to hold the battery steady on the back of your head,

but can be detached and replaced by the back cable guide if you want to keep your head-

lamp clean and simple - either solution lets you carry the battery in your pocket to keep the

weight o your head.

MODULAR SYSTEM

In order to move the headlamp body from the headband to either the helmet bracket or the

bike bracket, gently push the lamp upward relative the head plate with head band. Insert the

headlamp body in the new bracket and gently press it down until you hear a click sound.

BIKE HANDLEBAR ATTACHMENT

The bike handle bar attachment is developed for use on bike handlebars with a dimension

between 22 mm and 32 mm. The bike bracket is attached to the handle bar by wrapping the

rubber strap around the handlebar and fasten it on the plastic hook.

Attach the headlamp in the bike handle bar attachment by sliding the headlamp bracket into

the snap-in socket.

To remove, slide the headlamp up and out of the bracket.

HELMET ATTACHMENT

The helmet bracket + back cable guide comes with pre-mounted adhesive tape on the back

for easy mounting on any helmet. The adhesive is a polyethylene foam tape developed to not

damage or cause any type of weakness to the plastic in your helmet.

To mount the helmet bracket, remove the protective ﬁlm covering the adhesive tape. Make

sure the surface of the helmet is clean and dry. Press the bracket onto its correct position.

If you do not want to use the adhesive on your helmet the attachment is prepared for mount-

ing with 2 or more straps on the sides. (Not included)

Attach the headlamp in the helmet bracket by sliding the headlamp bracket into the snap-in

socket. To remove, slide the headlamp up and out of the bracket.

Attach the cable by using the back cable guide or integrated helmet strap.

Depending on helmet type, it might be preferable to use the Helmet mode – Flow light deac-

tivated, when the headlamp is used on a helmet.

The headband is designed to ﬁt on a helmet by detaching the ergonomic back plate – thus

giving you the flexibility to use either the included helmet bracket or to just snap the head-

lamp onto your helmet and go.

DURING USE

SILVA INTELLIGENT LIGHT® AND FLOW LIGHT

SILVA Intelligent Light® optimizes the light pattern by the unique combination of a long

reach spot light and a close flood light. With less head movements and a clear view of near as

well as far obstacles, you gain the balance and conﬁdence it takes to move fast and perform

better. Our ingenious SILVA Flow Light takes the optimization even further by providing

seamless tuning of the light pattern for your favourite sport. Simply tilting the light down-

wards makes the beams wider to brighten up slower activities. When tilting the headlamp

upwards, the light reaches longer to provide perfect vision when you move fast.

SWITCH ON YOUR HEADLAMP

A push button is located on the left side of the headlamp body. This button controls all light

modes.

• To start the headlamp with Flow Light activated press push button with a short press.

• To start the headlamp with Flow Light deactivated press and hold push button for 1

second

• To cycle between the dierent modes use short presses.

• To turn the headlamp o press and hold button for 1 second

MAX

SHORT PRESS

LONG PRESS

OFF OFF OFF

MED MIN

FLOW LIGHT ACTIVATED

FLOW LIGHT DEACTIVATED

DEACTIVATED FLOW LIGHT

Flow Light deactivated means that the Light image will remain unchanged even if the

headlamp is tilted up or down. This might be useful when the lamp is mounted on a helmet or

a bike handle bar.

BOOST MODE

Exceed 3 has a Boost mode that temporarily increases the light output to 2300 lumen during

10 seconds.

To enter Boost mode, do as follows:

• Turn headlamp ON (with Flow light activated or deactivated)

• Keep push button pressed until headlamp turns OFF and keep pressing the push button

until the headlamp turns back ON.

• Headlamp has now entered Boost mode

• The light will remain in Boost mode for 10 seconds and then return to the light mode from

where you entered Boost mode (for example MED)

Note! During the 10 seconds the headlamp is in Boost mode it is not possible to use push but-

ton.

TEMPERATURE CONTROL

Note that the headlamp body temperature will increase during use. The headlamp tempera-

ture is depending on light mode, ambient air temperature and the airflow (speed). Exceed 3 is

equipped with a temperature control unit that prevents the headlamp body from overheating

by reducing the power to the LEDs. This means that the lower the ambient temperature, the

stronger the light output.

Note! Always make sure to disconnect the battery when the headlamp is stored in a closed

compartment such as in a bag, pocket or similar.

LOW BATTERY WARNING

During operation of the headlamp there will be a low battery warning when 10% of the bat-

tery energy remains. This is done by flashing both LEDs for 1 second and repeated again after

5 seconds.

RESERVE MODE

During operation, the lamp will go into reserve mode when there is 10% power left of the bat-

tery. All LEDs will flash once before the lamp goes into this mode.

Reserve mode can be overridden by pressing the button.

Warning: If you have pressed the button when headlamp is in reserve mode no more low bat-

tery warnings will appear before the headlamp turns OFF.

BATTERY STATUS INDICATION

On the battery, there is a push button that activates battery indication LEDs. When pushing

the button 5 LEDs on the battery shows battery status according the following…

• 5 green LEDs = Fully charged

• 4 greed LEDs = 80% of the battery remains

• 3 greed LEDs = 60% of the battery remains

• 2 greed LEDs = 40% of the battery remains

• 1 red LED = 20% of the battery remains

To get as much power as possible out from your battery, keep it away from low temperatures

during use.

EXCEED 3X: Art. no 37739

EXCEED 3XT: Art. no 37740

EXCEED 3X EXCEED 3XT

FULL VERSION MANUAL

EXCEED 3 SERIES

Visit: www.silva/environment

for more information about the

Waste Electrical and Electronic

Equipment (WEEE) Directive.

AFTER USE

MAINTENANCE

To make sure you get maximum performance from your headlamp, clean it regularly with a

damp cloth. Headband cleaning – rinse in warm water.

TECHNICAL SPECIFICATIONS: EXCEED 3XT

Weight headlamp including headset: 129g

Battery weight: 371g

Battery type: Li-ion 7.4V, 9.9Ah

Light distance Max/Med/Min: 220m/120m/40m

Lumen Boost/Max/Med/Min: 2300/2000/1000/80

Burn time 20˚C Max/Med/Min: 12h/18h/60h

Burn time -5˚C Max/Med/Min: 3.5h/9h/60h

Reserve mode: 0.5h

Charging time: 10h

Water resistance: IPX5

Operative temperature range: -20 - +60º

TECHNICAL SPECIFICATIONS: EXCEED 3X

Weight headlamp including headset: 129g

Battery weight: 171g

Battery type: Li-ion 7.4V, 3.3Ah

Light distance Max/Med/Min: 220m/120m/40m

Lumen Boost/Max/Med/Min: 2300/2000/1000/80

Burn time 20˚C Max/Med/Min: 4h/6h/20h

Burn time -5˚C Max/Med/Min: 1h/3h/20h

Reserve mode: 0.5h

Charging time: 4h

Water resistance: IPX5

Operative temperature range: -20 - +60º

ABOUT LI-ION BATTERIES

The battery should be stored in a dry environment within the temperature range of

-20°C and +35°C.

If you would like to store your battery for a longer period (more than 30 days) the battery

should not be fully charged. This may cause loss of its characteristics.

Li-ion batteries have a discharge rate of approx. 20% over a 30-day period. You can always

charge a half full battery without damaging its characteristics.

Do not expose the battery for extreme temperatures which may cause ﬁre or explosion.

Do not disassemble or mistreat the battery; risk for chemical burn.

Keep away from children.

Do not dispose of batteries in ﬁre. This may cause an explosion.

Do not submerge the batteries in water.

Do not short circuit the contacts.

Replace only with Silva batteries with the same connector as on Exceed 3 battery.

PROTECTING THE ENVIRONMENT.

Headlamp, batteries and packaging are recyclable. Please dispose these items at designated

recycling stations.

WARRANTY

Silva warrants that, for a period of two (2) years*, your Silva Product will be substantially free

of defects in materials and workmanship under normal use. Silva’s liability under this war-

ranty is limited to repairing or replacing the product. This limited warranty extends only to the

original purchaser.

If the Product proves defective during the Warranty Period, please contact the original place

of purchase. Make sure to have your proof of purchase on hand when returning the product.

Returns cannot be processed without the original proof of purchase. This warranty does not

apply if the Product has been altered, not been installed, operated, repaired, or maintained in

accordance with instructions supplied by Silva, or has been subjected to abnormal physical

or electrical stress, misuse, negligence or accident. Neither does the warranty cover normal

wear and tear. Silva is not responsible for any consequences, direct or indirect, or damage

resultant from use of this product. In no event, will Silva’s liability exceed the amount paid by

you for the product. Some jurisdictions do not allow the exclusion or limitation of incidental

or consequential damages, so the above limitation or exclusion may not apply to you. This

Warranty is valid and may be processed only in the country of purchase.

* Batteries: 1 year

For more information please visit www.silva.se

EXCEED 3X: Art. no 37739

EXCEED 3XT: Art. no 37740

EXCEED 3X EXCEED 3XT

FULL VERSION MANUAL

EXCEED 3 SERIES

Page is loading ...

Silva Exceed 3X User manual

Brand: Silva

Model: Exceed 3X

Type: User manual

This manual is also suitable for

Exceed 3XT

Download PDF

report

in other languages

français: Silva Exceed 3X Manuel utilisateur
español: Silva Exceed 3X Manual de usuario
Deutsch: Silva Exceed 3X Benutzerhandbuch
svenska: Silva Exceed 3X Användarmanual

Silva Exceed 3X User manual

This manual is also suitable for

Silva Exceed 3X User manual

in other languages

Related papers

Other documents