PAC NU-CHY2 User manual

PAC
Brand
PAC
Model
NU-CHY2
Type
User manual

PAC NU-CHY2

PAC NU-CHY2 is a Navigation Unlock integration interface that allows the factory navigation features of your Chrysler/Dodge/Jeep radio or the reverse camera to be used by the passenger at anytime.

  • Allows the passenger to use the factory navigation features or the reverse camera while the vehicle is in motion.
  • Easy to install, simply connect the NU-CHY2 harness to the back of the radio and the factory 22-pin harness.
  • Controls are located on the steering wheel for easy access.
  • The dash mount LED provides a visual confirmation that the NU-CHY2 is active.
  • The reverse camera unlock feature allows the passenger to view the rearview camera image on the navigation screen.

PAC NU-CHY2

PAC NU-CHY2 is a Navigation Unlock integration interface that allows the factory navigation features of your Chrysler/Dodge/Jeep radio or the reverse camera to be used by the passenger at anytime.

  • Allows the passenger to use the factory navigation features or the reverse camera while the vehicle is in motion.
  • Easy to install, simply connect the NU-CHY2 harness to the back of the radio and the factory 22-pin harness.
  • Controls are located on the steering wheel for easy access.
  • The dash mount LED provides a visual confirmation that the NU-CHY2 is active.
  • The reverse camera unlock feature allows the passenger to view the rearview camera image on the navigation screen.
Pacic Accessory Corporation - Santa Ana, CA 92705
[email protected] • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
01-21-11
J1850
Class 2
VPW
Class 2
J1850
100011101111001001101100
111010000110110111001100
Arbitration
EOD
100011101111001001101100
111010000110110111001100
Class 2
Class 2
J1850
J1850
Class 2
VPW
Class 2
J1850
100011101111001001101100
111010000110110111001100
Arbitration
EOD
100011101111001001101100
111010000110110111001100
Class 2
Class 2
J1850
NU-CHY2
Chrysler/Dodge/Jeep
Navigation Unlock
Integration Interface
*These instructions only support revision 1.1.4 or higher of the NU-CHY1
Installation: Disconnect the main 22-pin harness from the back of the radio.
Plug the male connector on the NU-CHY2 harness into the 22-pin port on the
back of the radio. Connect the factory 22-pin harness into the female connector
on the NU-CHY2 harness.Plug the Black micro-t 24-pin connector on the NU-
CHY2 harness into the NU-CHY2.
In vehicles equipped with a Multi-Function Display (MFD) in the instrument
cluster or an external Uconnect module it is not necessary to connect and mount
the LED. The best way to determine if the UConnect is external is if the vehicle
has an external iPod or USB input (not including the one built into the front of the
radio). If the vehicle is not equipped with an MFD or external Uconnect module
mount the LED in a location that is visible to the driver.
If you wish to enable the reverse camera unlock feature you must power up the
factory reverse camera (this does not apply to the 2010+ Dodge Ram or 2011+
Jeep Grand Cherokee). To do this a wire must be ran from the NU-CHY2’s
red camera turn on wire to the factory power wire for the reverse camera. The
location of this wire will vary depending upon which vehicle you are installing the
NU-CHY2 into. Please see below for the different locations.
Please Note: If the customer does not wish to use the Reverse Camera unlock
feature you do not have to locate and connect this wire.
The NU-CHY2 is a Navigation Unlock integration interface that allows the factory navigation features of
your Chrysler/Dodge/Jeep radio or the reverse camera to be used by the passenger at anytime.
NU-CHY2
Chrysler/Dodge/Jeep
Navigation Unlock Interface
To Vehicle
Red Wire - Reverse Camera
Turn On Output
(12v+ 1 Amp Max)
To Factory Radio
NUCHY Harness
Connection Diagram
To dash-mount LED
Installation
Reverse Camera Wire Location Dodge Caravan/Chrysler Town & Country/VW Routan
1. You will need to locate the reverse camera wire in the rear harness located
above the rear door trim panel (Fig A).
2. The reverse camera wire is the white/green wire (test with a DMM to verify
12v when the vehicle is shifted into reverse) (Fig- B).
3. Connect the red camera turn on wire from the NU-CHY2 to the white/green
wire using a diode (Fig C). The diode is needed to prevent the reverse lights
from coming on when the reverse camera is activated.
4. Verify that the reverse lights do not come on when the reverse camera
unlock feature is being used.
Fig A
Fig B
Reverse
Camera
Red Camera Activation Wire
Wht/Grn Camera Wire
Connect Diode
Here
Connect Red Wire
From NU-CHY2 Here
Fig C
Page 1
Pacic Accessory Corporation - Santa Ana, CA 92705
[email protected] • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
01-21-11
J1850
Class 2
VPW
Class 2
J1850
100011101111001001101100
111010000110110111001100
Arbitration
EOD
100011101111001001101100
111010000110110111001100
Class 2
Class 2
J1850
1. You will need to locate the reverse camera wire in the reverse camera
harness located in the liftgate. (Fig A).
2. The reverse camera wire is the white/green wire (test with a DMM to verify
12v when the vehicle is shifted into reverse) (Fig- B).
3. Connect the red camera turn on wire from the NU-CHY2 to the white/green
wire using a diode (Fig C). The diode is needed to prevent the reverse lights
from coming on when the reverse camera is activated.
4. Verify that the reverse lights do not come on when the reverse camera
unlock feature is being used.
Fig A
Fig B Fig C
Reverse Camera Wire Location Dodge Journey
Page 2
Reverse
Camera
Red Camera Activation Wire
Wht/Grn Camera Wire
Connect Diode
Here
Connect Red Wire
From NU-CHY2 Here
NU-CHY2 Controls
**CONTROLS LOCATED ON RIGHT REAR OF STEERING WHEEL**
1. Press & Hold the Source Button
for at Least 2 Seconds Then
Release
2. MFD and/or Radio Will Display
“Confirm Safe Passenger Use”. If
Present, Dash Mount LED
Displays Red Light Prompting
Confirmation of Safe Passenger
Use
3. Press the Source Button Again
Within 5 Seconds to Confirm
4. MFD and/or Radio Will Display
“Acknowledged”. If Present Dash
Mount LED Displays Green
Light
5. Repeat Step 1 to De-Activate
Press & Hold the Source
Button to Enable/Disable
Navigation Unlock
Activating the Reverse Camera
**CONTROLS LOCATED ON LEFT REAR OF STEERING WHEEL**
1. Activate the NU-CHY2
2. Press & Hold the
Preset Button for at
least 2 seconds,
then release to
Activate the Reverse
Camera
Press & Hold the
Preset Button to
Enable/Disable
Reverse Camera
Operation - Vehicles With Steering Wheel Controls
Pacic Accessory Corporation - Santa Ana, CA 92705
[email protected] • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
01-21-11
J1850
Class 2
VPW
Class 2
J1850
100011101111001001101100
111010000110110111001100
Arbitration
EOD
100011101111001001101100
111010000110110111001100
Class 2
Class 2
J1850
DISCLAIMER: Under no circumstances shall the manufacture or the distributors of the NU-CHY2 be held liable for claims of any
loss or damage, consequential, direct or indirect, arising from the sale, installation, or use of the NU-CHY2. The manufacture
and its distributors will not, nor will they authorize any representative or any other individual, to assume obligation or liability in
relation to the NU-CHY2 other than its replacement.
AGREEMENT: End user agrees to use this product in compliance with the instructions and terms of use above and with all State
and Federal laws. PAC provides instructions and safety warnings with respect to this product and disclaims all liability for any use
not in conformity with those instructions or other misuse of its product. If you do not agree, please discontinue use immediately
and return product to place of purchase. This product is intended for off-road use and passenger use only.
Page 3
Activating the Navigation Unlock
Press and hold the “Source” button on the steering wheel controls (SWC) for at least two seconds and then release to activate the NU-CHY2. If
the vehicle is equipped with a MFD in the cluster it will display “Conrm Safe Passenger Use”. If the vehcle is equipped with an external Uconnect
module the radio will display “Press Again to Conrm Safe Passenger Use”. If present, the dash mount LED will illuminate red. Press the “Source”
button on the SWC again within 5 seconds to acknowledge “safe use”, agreeing that use will be performed only by the passenger
whenever the vehicle is in motion, and activate the NU-CHY2. If applicable, the MFD and/or radio will display “Acknowledged”. If present,
the dash mount LED will then illuminate green. To de-activate the NU-CHY2 simply press and hold the “Source” button on the SWC for at least
two seconds and then release.
Activating the Reverse Camera Unlock
Activate the navigation unlock using the SWC. Press and hold the “Preset” button on the SWC for at least two seconds and then release. The
dash mount LED will begin blinking and the rearview camera image will now display on the navigation screen.
WARNING: In order to avoid distraction, which could lead to an accident, the driver should never utilize systems unlocked by the
NU-CHY2 when the vehicle is in motion. Even when operated by the passenger, the vehicle driver should maintain their attention on
the road at all times.
Operation (Continued)
Operation - Vehicles Without Steering Wheel Controls
Activating the Navigation Unlock
Start with the factory radio on. Turn the radio off then on within three
seconds. The dash mount LED will illuminate red. Turn the radio off then
on again within three seconds to acknowledge “safe use”, agreeing
that use will be performed only by the passenger whenever
the vehicle is in motion, and activate the NU-CHY2. The dash
mount LED will then illuminate green. To de-activate the NU-CHY2
simply turn the radio off then on within three seconds.
WARNING: In order to avoid distraction, which could lead to an
accident, the driver should never utilize systems unlocked by the
NU-CHY2 when the vehicle is in motion. Even when operated by
the passenger, the vehicle driver should maintain their attention on
the road at all times.
LO AD
MENU
AUDIO
PULL
AUX
HARD DISC DRIVE
.1t8."t+1&(
VOLUME
MEDIA
RADIO
PUSH ON
RBZ
MY
FILES
1. Start with radio on.
2. Turn the radio o then on within 3 seconds.
The dashmount LED will illuminate red.
3. Turn the radio o then on again to conrm
safe use. The dash mount LED will illuminate green.
4. Repeat step 2 to de-activate.
Turn radio o and on
within 3 seconds to
activate/de-activate
the NU-CHY2
1. When installing this interface the vehicle must be turned off.
2. If the vehicle’s reverse lights come on when the reverse camera feature is engaged the diode is not wired properly. Please refer to “Fig. C” on
page one or two for proper diode wiring.
3. If the factory radio does not come on or “ickers” off & on, the factory amplier does not turn on or you are receiving audio on only one side of
the vehicle, please make sure that the male pins in the NU-CHY2 plug are not bent or out of place.
4. In order to see the text on the MFD it must be in the default display of the temperature/compass or at the top of the list if setup in list format.
Installation Notes/Troubleshooting
  • Page 1 1
  • Page 2 2
  • Page 3 3

PAC NU-CHY2 User manual

PAC
Brand
PAC
Model
NU-CHY2
Type
User manual

PAC NU-CHY2

PAC NU-CHY2 is a Navigation Unlock integration interface that allows the factory navigation features of your Chrysler/Dodge/Jeep radio or the reverse camera to be used by the passenger at anytime.

  • Allows the passenger to use the factory navigation features or the reverse camera while the vehicle is in motion.
  • Easy to install, simply connect the NU-CHY2 harness to the back of the radio and the factory 22-pin harness.
  • Controls are located on the steering wheel for easy access.
  • The dash mount LED provides a visual confirmation that the NU-CHY2 is active.
  • The reverse camera unlock feature allows the passenger to view the rearview camera image on the navigation screen.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents