wedi US4000001 User manual

Brand: wedi

Model: US4000001

Type: User manual

wedi US4000001 is a shower and bath tub surround kit that provides a fast, light, and safe way to tilebacker walls. It is 100% waterproof, lightweight, and easy to cut cleanly. It can be notched out on the bottom to perfectly connect to a tub flange. The kit includes all the necessary components for installation, including building panels, flexi collars, joint sealant, washers, and screws. wedi US4000001 is UPC/IPC approved and comes with a 10-year warranty.

Here are 3 possible use cases of "wedi US4000001"

As a backer board for tile in showers and bathtubs
As a way to create a waterproof barrier around bathtubs and showers

Here are 3 possible use cases of "wedi US4000001"

As a backer board for tile in showers and bathtubs
As a way to create a waterproof barrier around bathtubs and showers

wedi Shower and Bath Tub Surround Kit

Fast, light, safe shower and tub tilebacker walls

Needed for Installation Installation

 Screw gun

 Utility knife

 Straight edge

 Measure tape

 Caulk gun

Special Features

 100 % internally and throughout waterproof and not only resistant

 Lightweight and easy to cut cleanly

 Can be notched out on bottom to perfectly connect to a tub ﬂange

 No additional waterprooﬁng needed like with cement

or gypsum based baker boards

 Protect your framework and structures against mold, mildew and

other water related damage potential using wedi building panels

 Comes with system joint sealant and fasteners

 UPC / IPC approved / complaint

 10 year warranty

Kit included

 (5) wedi 3’ × 5’ × 1/2“

Building Panels

 (5) wedi Joint Sealant, 10.5 oz.

 (1) Mixing Valve Flexi Collar

 (1) Flexi Collar

 (1) Corner Putty Knife

 100 ct. of wedi Tab Steel Washers



100 ct. of wedi Galvanized Screws

wedi Corporation

Tel. +1-847-357-9815

Fax. +1-847-357-9819

[email protected]

www.wedicorp.com

AYBAZE A US6000067 wedi information and instruction is based on best knowledge and independent testing (UPC/IAPMO).

Measure and cut wedi Building Panel

to ﬁt the 16 inch o.c. framework

(wood or metal). Notch out all pan-

els if installed around the perimeter

of a ﬂange tub to integrate the

ﬂange and achieve a plumb wall

with square and tight corners.

03 04

Apply a continuous 1/2“ bead of wedi Joint Sealant on the top blue foam edge of

the wedi Building Panel before installing the next panel, butting tightly into the

sealant. Set another wedi Washer and Screw into the seam to create a ﬂush transi-

tion between panels and smooth over excess sealant. When installing a wedi side

panel against the already ﬁxed wedi back wall, apply a continuous 1/2“ bead of

wedi Joint Sealant vertically on the back wall wedi panel where both panels will

meet. Apply compression to the wedi Joint Sealant when moving the wedi side

panel into position before fastening it.

Finally and after all wedi Building Panels are installed a second 1/2” bead of wedi Joint

Sealant is applied over all seams and fastener points and spread ﬂat using a putty knife.

Attach a notched panel to the frame-

work with a 1/2” bead of wedi Joint

Sealant between the notch and

ﬂange. Attach the panel to the

framework using wedi Washers and

Screws at a rate of 1 every 12 inches

along the studs. Leave a gap of 1/8“

between tub edge and wedi panel

bottom end to allow for movement

of the tub. Alternatively apply a bead

of wedi Joint Sealant in between

both materials.

wedi_MA_USA_Shower-Surround-Kit_2018_lay2_90157000 27.03.18 08:34 Seite 1

wedi US4000001 User manual

Brand: wedi

Model: US4000001

Type: User manual

Here are 3 possible use cases of "wedi US4000001"

As a backer board for tile in showers and bathtubs
As a way to create a waterproof barrier around bathtubs and showers

Download PDF

report

wedi US4000001 User manual

wedi US4000001 User manual

Related papers

Other documents