Levana Clara KBHP5 User manual

1

Clara

TM

Product Manual

High Resolution Video Baby Monitor

KBHP5

CAUTION: Keep small parts away from children.

Proudly Designed in Canada

1

Your feedback is essential to helping us make our products the

best they can be for all parents.

Please share your Levana story with us!

www.mylevana.com

Thank You

For bringing Levana home!

/mylevana @mylevana blog.mylevana.com

2

SAFETY INSTRUCTIONS & DISCLAIMERS

Safety Instructions

Caution: This product contains small parts. Exercise care when unpacking and assembling the product and accessories. Failure

to do so can result in choking or death.

Caution: This product is not a toy and should be kept out of children’s reach.

Caution: This is not a medical product. If there is a problem with your child, call 911 immediately.

Strangulation Hazard: Children can become entangled in cords. Power cords should be kept at least 3 ft away from the crib and

baby’s reach at all times. Failure to do so could be fatal. Baby monitors and cameras with power cords should never be hung on

or near the crib.

Supervision: This product does not replace responsible adult supervision. Check on your child at regular intervals and make

sure your monitor is always adequately charged. Failure to do so can be fatal.

Power Source: LEVANA® highly recommends the use of an Uninterruptible Power Supply (UPS) with surge protection when

plugging in the camera and monitor. This product should only be used with the AC power adapters included.

Water and Moisture: Product intended for indoor use only. The unit should not be exposed to rain, moisture, dripping or

splashing, and should not be used near water.

Keep Away from Heat Sources: This product should not be exposed to direct heat sources such as a candle, replace, radiator,

heat register, stove or other appliances that emit heat. The product should not be left in direct sunlight.

Non-Use Periods: Always unplug the AC adapters from the wall outlet during long periods of non-use.

Damage Requiring Service: This product should be serviced by qualied personnel only, when:

A. Product has fallen or liquid has spilled into the unit.

B. Product has been exposed to liquids or moisture.

C. Product does not appear to operate normally or exhibits a distinct change in performance.

D. Product has been dropped or the casing has been damaged.

• Please note that the above mentioned are not covered under the product warranty.

3

SAFETY INSTRUCTIONS & DISCLAIMERS

Disclaimers

• We reserve the right to change models, conguration or specications without notice or liability. Product may not be

exactly as shown.

• Optimum range is 150 ft when signal is passing through walls or oors. Microwave ovens (when in use) may cause signal

disruption at close range. Buildings with metal frames may also cause signal disruption. Maximum transmission range is

900 ft in an open area.

• Night Vision range is up to 12 ft under ideal conditions. Objects at or beyond this range may be partially or completely

obscured, depending on the camera application.

• Battery life of 8 hours based on Power Save mode. Battery lasts an average of 4 hours with continuous audio/video usage.

are the property of their respective owners.

4

COMPLIANCE STATEMENTS

FCC Caution

Any changes or modications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC Warning

This device complies with CNR Industry Canada license-exempt devices. Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of

the device.

This device is compliant with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.

The minimum distance from body to use of the device is 20 cm.

5

SUPPORT

We take quality very seriously. This is why all of our products come with a one-year warranty from the original purchase

date against defects in workmanship and materials. If you have warranty or support issues, please contact us at:

Web: www.mylevana.com Support: www.mylevana.com/Support_Center.eng.html

Levana Canada Levana USA

4080 Montrose Road 840 Aero Drive

Niagara Falls, ON Cheektowaga, NY

Canada, L2H 1J9 USA 14225

Product Manual Feedback

At Levana, we’re always looking to improve your experience. Please share any suggestions for this product

manual to help us continue on this journey. CLICK HERE FOR FEEDBACK SURVEY LINK

Help Videos

Click to access our Support Center or visit our website at www.mylevana.com and open Resources on the

product page. These videos provide a visual guide for setting up and using your monitor.

www.mylevana.com/videos

6

WARRANTY TERMS

• LEVANA® products are guaranteed for a period of one year from the date of purchase against defects in workmanship and

materials. This warranty is limited to the repair, replacement or refund of the purchase price at LEVANA®’s options.

• This warranty becomes void if the product shows evidence of having been misused, mishandled or tampered with contrary

to the applicable instruction manual.

• Routine cleaning, normal cosmetic and mechanical wear and tear are not covered under the terms of this warranty.

• The warranty expressly provided for herein is the sole warranty provided in connection with the product itself and no other

warranty, expressed or implied is provided. LEVANA® assumes no responsibilities for any other claims not specically men-

tioned in this warranty.

• This warranty does not cover the shipping cost, insurance or any other incidental charges.

• You MUST contact LEVANA® at www.mylevana.com/Contact before sending any product back for repair. You will be sent

a Return Authorization form with return instructions. When returning the product for warranty service, please pack it

carefully in the original box with all supplied accessories, and enclose your original receipt or copy, and a brief explanation of

the problem, and include the RA number.

• This warranty is valid in Canada and the contiguous US.

• This warranty cannot be re-issued.

• Please visit our website at www.mylevana.com/store-policies for additional information about your product warranty.

7

TABLE OF CONTENTS

Thank You ...................................................................................................... 1

Safety Instructions & Disclaimers

Safety Instructions ................................................................................. 2

Disclaimers.............................................................................................. 3

Compliance Statements .............................................................................. 4

Support ........................................................................................................... 5

Warranty Terms ............................................................................................ 6

What’s Included ............................................................................................. 8

Buttons & Features ....................................................................................... 9

Getting Started .............................................................................................. 10

Connecting Power To The Monitor ...................................................... 10

Charging The Battery ............................................................................. 10

Getting The Most Out Of Your Rechargeable Battery ....................... 10

Connecting Power ToThe Camera ....................................................... 10

Introduction Screens ............................................................................. 11

Status Bar ................................................................................................ 12

Setup

Monitor Placement ................................................................................ 13

Camera Placement ................................................................................. 13

Features

Pan/Tilt/Zoom ......................................................................................... 15

Volume Controls ..................................................................................... 16

Talk To Baby

tm

......................................................................................... 17

Accessing The Menu .............................................................................. 17

Menu Functions

Power Save.............................................................................................. 18

Lullabies .................................................................................................. 19

Feeding Timer ......................................................................................... 19

Camera select (Single View-Active Camera) ........................................ 20

Split Screen ............................................................................................. 21

Quad Screen ........................................................................................... 21

Sequence Screen .................................................................................... 21

Camera pairing

Pairing ...................................................................................................... 22

Un-Pairing ............................................................................................... 22

Night Vision ............................................................................................. 23

Settings

Language ................................................................................................. 24

Brightness ............................................................................................... 24

Time Set ................................................................................................... 25

Factory Reset .......................................................................................... 25

Temperature ........................................................................................... 26

Auto Motion Tracking ............................................................................ 27

Support .................................................................................................... 28

Battery Installation ....................................................................................... 29

Maintenance .................................................................................................. 29

Troubleshooting ............................................................................................ 30

Frequently Asked Questions ....................................................................... 32

Specications ................................................................................................. 33

8

WHAT’S INCLUDED

• 5” High Resolution Baby Video Monitor

• 2 Rechargeable Battery Packs (Installed)

• Pan/Tilt/Zoom Night Vision Camera

• 2 Power Adapters (Monitor and Camera)

• Camera Mounting Hardware

• Quick Start Guide

• 1 Year Warranty

• Lifetime Customer Support

Adding Cameras

Your Clara monitor is expandable up to 4 cameras and is compatible with Clara PTZ cameras.

• Visit www.mylevana.com to nd product details.

Clara Additional Camera

KBHP5C ONLY

9

BUTTONS & FEATURES

1. Power ON/OFF (Top)

2. Exit/Back

3. Volume-/+ (Side)

4. Navigation Arrows

5. Menu/OK

6. Talk to Baby

TM

7. Microphone

8. Stand (Back)

9. Power Input (Side)

10. Speakers

1. Night Vision Sensor

2. Microphone

3. Power LED (Side)

4. Power ON/OFF (Side)

5. Power Input (Side)

6. Temperature Sensor (Back)

7. Antenna (Back)

8. Pairing Button (Bottom)

10 1

2

3

4

5

6

78

9

1

2

4

5

6

7

8

3

10

GETTING STARTED

Connecting Power to the Monitor |

Charging the Battery

Getting the Most Out of Your Rechargeable Battery

• Fully charge the battery (approximately 4 hours) before the rst use. The battery power status will appear on the Status

Bar and should be 100%

• Charge the battery before it fully drains to maximize battery life. We recommend charging daily.

• Avoid exposing the battery to extreme heat or cold, extreme temperatures will aect the life of the battery.

• Activate Sleep Mode, the monitor automatically sleeps after a few seconds of inactivity to extend battery life.

• Decrease screen Brightness to extend battery life.

WARNING: Baby monitors and cameras with power cords should never be hung on or near the crib as it is a strangulation

hazard. Power cords should be kept no less than 3 ft away from the crib and baby’s reach at all times.

• Press and hold the power button until the moni-

tor turns ON/OFF (approximately 3-5 seconds).

• When the monitor turns on the Introduction

screen will appear after the Levana splash screen.

See page 11 for Introduction instructions.

• Slide the power switch to turn the camera

ON/OFF.

• If the camera is not automatically paired after

setup is complete you will need to pair it

manually. See page 22 for pairing instructions.

Connecting Power to the Camera

11

GETTING STARTED

Introduction Screens

When you turn on your monitor for the rst time and after a Factory Reset, the Introduction will appear on the screen. This

feature gives you the option to create settings and to learn more about how your monitor works.

• Use the Navigation Arrows on the front of the monitor to move through the option and screens. Press OK to

make a selection

• Access the Introduction screen at any time through the Support menu option. See page 28 for Support instructions.

Setup & Functions FAQ

am

12 :

45

Please set the time

Please choose a language

English

Français

Español

Provides screen for selecting/changing Language/Time and a

description of Button Functions.

1. Choose your preferred Language from the list using the

UP/DOWN navigation arrows and press OK to set

and move the next screen.

2. Use the RIGHT/LEFT navigation arrow to move through

the options and to the next/previous screen.

3. Use the UP/DOWN navigation arrows to change the

Hour/Minutes to set the time.

After the initial setup and function screens, the FAQ list will

appear. This provides a list of the most frequently asked

questions with instructions.

1. Use the UP/DOWN arrows to move through the list of

Questions.

2. Press OK to open a Question and the RIGHT/LEFT

arrows to view the details.

3. Choose the X (bottom of the page) to exit by pressing OK

when the X is highlighted.

4. Choose 'Do no show again' to stop the Introduction

screen from showing the next time the monitor is

powered ON by pressing OK when the eld is

highlighted.

12:45

am

22°c

1

How do I pair additional cameras?

How do I set a Feeding or Nap Timer?

How do I change the volume on my camera

How do I use the Pan Tilt Zoom function?

How can I save battery Life?

Power / Sleep Mode

Menu / Exit

Volume

Menu Navigation /

PT2 Function

OK / Zoom

Talk to Baby

Button & Functions

12

GETTING STARTED

Status Bar

Notication Bar

High

Average

Low

Very Low

High

Medium

Low

Mute/OFF

Feeding Timer

100%

50-75%

25-50%

0-25%

Battery Charging

Very High

High

Average

Low

Very Low

22°c

Lullabies ONM

Temperature

(Active Camera Only)

Temperature Alert - Cold

Temperature Alert - Hot

Active Camera

(# shows which camera is active)

Sequence Mode

Camera Unpaired

SIGNAL STRENGTH CAMERA MODES FEATURES

VOLUME LEVELS SOUND INDICATORS BATTERY LEVELS

ON SCREEN ALERTS

13

SETUP

3

ft

Monitor Placement

Use the retractable stand on the back of the monitor to place it on a table top.

When not in use, clip the stand back in place so that the bracket is ush with the

back of the monitor.

Camera Placement

The camera can be placed on a table top or hung on the wall above the area being monitored.

• Place the camera within 10 ft of the area being monitored for best picture results.

• Do not place objects within 3 ft of the eld of view of the camera. Night vision will not

activate correctly if objects are closer than 3 ft.

• Use the Pan/Tilt/Zoom feature to adjust the angle of the camera.

TABLETOP PLACEMENT

1. Place the camera on a tabletop no less than 3 ft away from

the baby’s crib.

2. Feed the power cord down the back of the table or use wall clips

(not included) to secure the cord away from baby’s reach.

3. Connect the power cord to the wall outlet.

4. Check the view on the monitor to ensure there are no obstructions

and that you have a good view of your baby.

WARNING: Baby monitors and cameras with power cords should never be hung on or near the crib as it is a strangulation

hazard. Power cords should be kept no less than 3 ft away from the crib and baby’s reach at all times.

14

SETUP

WALL PLACEMENT

Important: Before drilling, check the camera placement and reception. Ensure you are hanging the camera no less than

3 ft away from baby’s crib.

1. Pre-drill one hole in the wall using a drill bit that meets the size

of the screw.

2. Insert a wall anchor (included) into the hole and tap gently

with a hammer until the anchor is ush with the wall.

3. Insert the screw into the wall anchor and tighten until the

screw sticks out approximately a ½”.You may need to adjust

more than ½” to ensure the camera is snug to that wall.

4. Connect the power cord to the power input on the camera.

5. Locate the wall mounting hole on the bottom of the

camera base.

6. Slide the hole over the screw on the wall until the

camera is in place.

7. Check that the camera is secure against the wall.

Adjust the screw to ensure the camera is not loose.

8. Connect the power cord to the wall outlet.

9. Use wall clips (not included) to secure the power cord

away from the crib and baby’s reach.

NOTE: When placing the camera on a wall stud, wall anchors are not required.

WARNING: Baby monitors and cameras with power cords should never be hung on or near the crib as it is a strangulation

hazard. Power cords should be kept no less than 3 ft away from the crib and baby’s reach at all times.

3

ft

15

FEATURES

Clara comes with a PTZ (Pan/Tilt/Zoom) camera view 300° horizontally and 110° vertically from the center position. You can also

zoom in 2x from the Camera Select menu.

Pan/Tilt

From the View screen press the Navigation Arrows UP/DOWN

and RIGHT/LEFT to adjust the camera view.

Zoom

Zoom is available through the Camera Select option.

12:45

am

22°c

1

1. Open the Menu, choose Camera, and press OK.

2. Choose Camera Select and press OK.

3. Choose the Camera and press OK to make it the Active

Camera.

4. Choose 2x Zoom and the camera will zoom in on the

image shown on the screen.

5. Repeat steps 1-3 and choose 1x Zoom to return to

normal view.

When in Sequence Mode you can just adjust the view on the

Active Camera while it appears on the screen.

12:45

am

22°c

Zoom Settings

ZOOM X2

ZOOM X1

16

FEATURES

Volume Controls

MONITOR

Use the + / - buttons on the side of the monitor to adjust

the volume. As you press the buttons the volume level will

appear on the screen.

• Press the + (top volume button) to increase the volume

coming from the Active Camera.

• Press the – (bottom volume button) to decrease the

volume coming from the Active Camera.

• Press the – (bottom volume button) so that no bars are

active to Mute all sounds.

NOTE: The selected volume level will appear on the Status Bar.

CAMERA

The camera volume is adjusted from the Lullabies menu for

all sounds.

• Open the Lullabies menu and move the Camera

Volume UP/DOWN using the Navigation Arrows. This will

increase/decrease the sound coming from the camera for

lullabies and when talking to baby.

12:45 am

22°c

12:45 am

22°c

Camera VolumeTimerLullaby

Lullaby 1 5 min

Lullaby 2

Nature Sounds 1

Nature Sounds 2

White Noise

15 min

30 min

45 min

60 min

17

FEATURES

Talk To Baby

TM

With the simple press of a button, you can talk to your child

at any time, without entering the room, through the Active

Camera.

1. To talk, press and hold the Talk button on the front

of the monitor and talk into the microphone. The talk

icon will show on the bottom right of the screen

while Talk To Baby™ is active.

2. Release the button to listen.

• Talk To Baby™ will work with the Active Camera only.

You can change the Active Camera from the Camera

Select menu.

Accessing the Menu

1. Press the OK button on the front of the monitor

to open the Menu.

2. Use the Navigation Arrows to move to a menu

option. The option will be changed to orange

when selected.

3. Press OK to select the option.

• Press the Exit/Back button on the front of the

monitor to move to the previous screen and to

return to the View screen.

Power Save Lullabies Feed/Nap Timer

Settings Support

12:45

am

22°c

1

Camera

18

MENU FUNCTIONS

Use the Power Save features to extend the battery life of your monitor.

Power Save

SLEEP MODE

When selected, the video monitoring will shut o when no

sound is heard. The screen will wake when baby makes

enough sound, based on the sensitivity level set.

Sleep Mode only works with the Active Camera and not with

the Sequence Mode.

1. Open the Menu, choose Power Save, and press OK.

2. Choose Sleep Mode and press OK.

3. Choose the Sensitivity Level for how much sound

needs to be detected for the screen to turn back on.

4. Press OK to turn Sleep Mode ON. The screen will turn

o after 20 seconds and turn back on when sound is

detected.

Choose ALWAYS ON to turn o Sleep Mode and

return to continuous video monitoring.

AUDIO ONLY

When selected, the video monitoring will shut o and allow

for audio monitoring only (no screen view).

If you have more than 1 camera connected, use Sequence

Mode and Audio Only to cycle the audio between all paired

cameras for 10 second intervals.

1. Open the Menu, choose Power Save, and press OK.

2. Choose Audio Only and press OK. The screen will turn

o after 20 seconds and allow for audio only

monitoring.

3. Press OK again to turn Audio Only monitoring OFF and

to return to continuous video monitoring.

Sleep Mode

12:45 am

22°c

1

Audio Only Always On

Audio Only Sleep Mode

12:45 am

22°c

1

Always On

Sensitivity Level

19

Set a Timer to remind you when it's time for baby's next feeding.

The Timer can be set to alert once or be repeated at every time

interval set.

1. Open the Menu, choose Feeding Timer, and press OK.

2. Choose the desired Camera and press OK.

3. Choose the Feed Timer type and press OK to select.

4. Choose the Alarm Settings option and press OK to set.

• Audible: sounds an alarm from the monitor.

• On Screen: ashes the alarm icon on the screen at

3 second intervals.

5. Adjust the Alarm Duration and press OK.

• Repeat: alert is enable at every interval set on the Timer.

• Once: alert is enabled only once for the time set.

Select from the 2 Lullabies, 2 Nature Sounds or White Noise to

help soothe baby to sleep. Set timers for playing sounds and

control the camera volume levels.

1. Open the Menu, choose Lullabies, and press OK.

2. Choose the desired Camera and press OK. The lullaby

sound with play through the camera selected.

3. Choose the Lullaby type and press OK to select.

4. Choose the Timer option for how long the lullaby will

play and press OK to set.

5. Adjust the Camera Volume and press OK. This will set

the volume on the camera for Lullabies and Talk to

Baby™

MENU FUNCTIONS

Lullabies Feeding Timer

12:45

am

22°c

Camera VolumeTimerLullaby

Lullaby 1 OFF

Lullaby 2

Nature Sounds 1

Nature Sounds 2

White Noise

15 min

30 min

45 min

60 min

Lullabies

Feed/Nap Timer

Page is loading ...

Levana Clara KBHP5 User manual

Levana Clara KBHP5 User manual

Related papers

Other documents