HOME by Argos HM OO BROMHAM OAK TABLE 4 BLACK CHAIRS User manual

Brand
HOME by Argos
Model
HM OO BROMHAM OAK TABLE 4 BLACK CHAIRS
Type
User manual

This manual is also suitable for

HOME by Argos HM OO BROMHAM OAK TABLE 4 BLACK CHAIRS is a dining table and chair set that is designed to be sturdy and easy to assemble. The table is made of melamine, which is a durable and easy-to-clean material. The chairs are made of solid oak and have black faux leather seats. The table measures 120cm in width, 80cm in depth, and 75cm in height. The chairs measure 44cm in width, 54cm in depth, and 95cm in height. They are comfortable to sit in and easy to move around.

HOME by Argos HM OO BROMHAM OAK TABLE 4 BLACK CHAIRS is a dining table and chair set that is designed to be sturdy and easy to assemble. The table is made of melamine, which is a durable and easy-to-clean material. The chairs are made of solid oak and have black faux leather seats. The table measures 120cm in width, 80cm in depth, and 75cm in height. The chairs measure 44cm in width, 54cm in depth, and 95cm in height. They are comfortable to sit in and easy to move around.

Dining Chair
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 08/12/12
Dimensions
Width - 44cm
Depth - 54cm
Height - 95cm
603/1035
603/1059
603/1042
1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warnings
Care and maintenance
• Assemble this product on a flat
surface.
• Assemble all parts loosely
before tightening any bolts.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Discard all extra fittings and
keep fittings out of reach of
children.
• Unit weight: 5.4kgs.
• Maximum safe weight of user:
110kgs.
• Retain Assembly Instructions
for future reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• This product should only be
used on firm, level ground.
• Make sure the legs remain in
contact with the ground.
• Do not stand on the product.
• Please clean the unit surface
using either damp (not wet)
cloth and a mild domestic soap
solution or by using an
appropriate polish.
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this
unit.
2
Components - Parts
Components - Fittings
Please check you have all the parts listed below
Please check you have all the fittings listed below
Backrest
(36 x 10 x 95cm)
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
1 Seat
(43.5 x 41.5 x 17.5cm)
2 Leg x 2
(43 x 3 x 3cm)
3
A
D
M8 x 60mm Bolt x 9
B
Allen key x 1
C
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
Washer x 9Spring washer x 9
Step 2
3
Assembly Instructions
2
2
1
3
3
A
A
A
C
C
A C
C
2
3
A
A
C
C
BB
B
B
B
B
B
A
C
B
C
2
1
B
A
A
C
B
A
C
B
A
C
B
A
C
B
Step 1
Place the backrest on a
flat protected surface.
Position the seat on
the backrest as
shown and fix using bolts
, spring washers
and washers .
Important:
Fasten bolts
using allen key
but do not fully
tighten at this
stage.
1
2
D
A B
C
Attaching backrest
Attaching legs
Place the seat upside
down on a flat protected
surface.
Insert the legs into the
holes of the seat as
shown and fix using bolts
, spring washer and
washers .
Important:
Fasten bolts
using allen key
but do not fully
tighten at this
stage.
2
3
A
D
B
C
D
D
4
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Aligning & securing the
legs
Carefully turn the chair
upright and place on a
flat surface.
a: Tighten all bolts using
allen key .
Note: This step is
essential to prevent the
chair from wobbling due
to uneven legs.
b: Carefully sit on the
chair and make
adjustments to ensure
the legs are flat even on
the floor.
c: After the sitting test,
re-tighten bolts again if
any adjustment is
needed.
Note: It is highly
recommended to
re-tighten all bolts after
using the chair for 7
days.
Note: Keep allen key to
re-tighten bolts when
required.
D
Assembly is complete.
Assembly Instructions
Step 3
a:
b:
c:
Dining Chair
Assembly Instructions - Please keep for future reference 603/7792
603/7826
603/1035
Important
- Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 21/08/13
Dimensions
Width - 43.5cm
Depth - 56cm
Height - 95cm
603/1059
603/1042
603/7802
1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warnings
• Assemble this product on a flat
surface.
• Assemble all parts loosely
before tightening any bolts.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Discard all extra fittings and
keep fittings out of reach of
children.
• Unit weight: 5.2kgs.
• Maximum safe weight of user:
110kgs.
• Retain Assembly Instructions
for future reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• This product should only be
used on firm, level ground.
• Make sure the legs remain in
contact with the ground.
• Do not stand on the product.
Care and maintenance
• Please clean the product using
either damp (not wet) cloth and
a mild domestic soap solution or
by using an appropriate polish.
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this
unit.
2
Components - Parts
Components - Fittings
Please check you have all the parts listed below
Please check you have all the fittings listed below
Backrest
(36 x 10 x 95cm)
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
1 Seat
(43.5 x 41.5 x 17cm)
2 Leg x 2
(3 x 3 x 43cm)
3
A
D
B C
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
Allen key x 1
Flat washer x 11
Spring washer x 11M6 x 50mm Bolt x 11
3
Place the backrest on a
flat protected surface.
Position the seat on
the backrest as
shown and fix using bolts
, spring washers
and washers .
Important:
Fasten bolts
using allen key
but do not fully
tighten at this
stage.
Note:
Use oval head of
allen key on
tight angles.
Assembly Instructions
Step 1
Step 2
2
1
2
3
3
D
D
A
A
A
A
C
B
C
CB
A CB
C
B
B
Attaching backrest
2
1
A
C
B
A
C
B
A
B
C
A
C
B
A
C
B
A
C
B
A
C
B
A
C
B
A
C
B
2
1
A
C
B
Attaching legs
Place the seat upside
down on a flat protected
surface.
Insert the legs into the
holes of the seat as
shown and fix using bolts
, spring washers
and washers .
Important:
Fasten bolts
using allen key
but do not fully
tighten at this
stage.
Note:
Use oval head of
allen key on
tight angles.
2
3
A
D
D
B
C
2
3
A
A
B
C
B
C
4
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
D
Aligning & securing the
legs
Carefully turn the chair
upright and place on a
flat surface.
a: Tighten all bolts using
allen key .
Note: Use oval head of
allen key on tight
angles.
Note: This step is
essential to prevent the
chair from wobbling due
to uneven legs.
b: Carefully sit on the
chair and make
adjustments to ensure
the legs are flat even on
the floor.
c: After the sitting test,
re-tighten bolts again if
any adjustment is
needed.
Note: It is highly
recommended to
re-tighten all bolts after
using the chair for 7
days.
Note: Keep allen key to
re-tighten bolts when
required.
D
D
Assembly is complete.
D
Assembly Instructions
Step 3
a:
b:
c:
Melamine 120cm Table
Dimensions
Width - 120cm
Depth - 80cm
Height - 75cm
Issue 1 - 27/04/12
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the
Assembly Instructions - Please keep for future reference
633/1333
Customer Helpline: 0845 640 0800
633/1412
633/1326
1
Safety and Care Advice
Im por t ant – Please read these instructions fully before starting assembly
• We do not
recommend the
use of power
drill/drivers for
insert ing screw s ,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product during assembly,
this could cause damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
●
●
●
●●
●
●
●
Components - Panels
Please check you have all the panels listed below
2
1 2
Top (120 x 80cm) Leg x 4 (73.2 x 5.5cm)
If you have damaged or missing components,
call the
Underside
Customer Helpline: 0845 640 0800
3
Bolt x 8
(M8 x 80mm)
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
Bolt Insert x 4
(M12 x 60mm)
D
Spring Washer x 8
B
Washer x 8
C
Not e: The quantities below are the correct amount to complete the assembly. In some cases more
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
105
Components - Fittings
E
Nut x 8
F
Wrench x 1
Flatblade Screwdriver
4
Assembly Instructions
Step 1
Step 2
2
1
C
D
Turn the table over
carefully.
Assembly is complete.
If you need help or have damaged or missing parts, call the
Argos Ltd MK9 2NW
Customer Helpline: 0845 640 0800
F
E
D
C
1
2
2 2
A
B
Attaching legs
Attach the four legs
to table top using
flat washers , spring
washers and nuts .
Tighten the nuts with
wrench .
E
F
E
Insert bolt inserts into
legs . Use a flat-
blade screwdriver to
align the bolt holes of
and the table leg
holes. Screw bolts
in, making sure the
lengths are the same.
B
A
2
A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

HOME by Argos HM OO BROMHAM OAK TABLE 4 BLACK CHAIRS User manual

Brand
HOME by Argos
Model
HM OO BROMHAM OAK TABLE 4 BLACK CHAIRS
Type
User manual
This manual is also suitable for

HOME by Argos HM OO BROMHAM OAK TABLE 4 BLACK CHAIRS is a dining table and chair set that is designed to be sturdy and easy to assemble. The table is made of melamine, which is a durable and easy-to-clean material. The chairs are made of solid oak and have black faux leather seats. The table measures 120cm in width, 80cm in depth, and 75cm in height. The chairs measure 44cm in width, 54cm in depth, and 95cm in height. They are comfortable to sit in and easy to move around.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents