Rosen GM SERIES DS-GM0710 Installation guide

Brand: Rosen

Model: GM SERIES DS-GM0710

Category: Car video systems

Type: Installation guide

Multi-Media Navigation System Installation Guide DP-GM0714IG Rev D

Installation Guide

NOTICE OF INTENDED INSTALLATION AND USE E

THE ROSEN MULTI-MEDIA NAVIGATION SYSTEMS CONTAIN AN INTERNAL VIDEO PLAYER, WHICH IS

NOT INTENDED FOR VIEWING BY THE DRIVER. THE VIDEO PLAYER IS DISABLED WHEN THE

VEHICLE IS IN MOTION THROUGH A CONNECTION TO THE PARKING BRAKE. THE INSTALLER OF

THIS PRODUCT MUST INSURE THE VIDEO DISABLE CONNECTION IS WORKING PROPERLY PRIOR TO

DELIVERY OF THE VEHICLE. IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR

INTERFERE WITH SAFE OPERATION OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY

OR DEATH, AND COULD ALSO VIOLATE STATE AND/OR FEDERAL LAW.

ROSEN ENTERTAINMENT SYSTEMS DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR

PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION

AND/OR USE.

BEFORE YOU START THE INSTALLATION, READ THIS GUIDE!

Rosen Multi-Media systems are the easiest-to-install OEM Radio replacement systems available today.

However, we strongly recommend reading this guide before starting the installation!

For additional technical tips, please visit

www.Rosendealercentral.com

1 Vehicle Compatibility

The Rosen Multi-Media Navigation System is designed to operate on the GM 29Bit Data CAN Bus. However,

GM Produces some vehicles with an 11Bit Radio which look identical, but are not compatible with this unit.

If your Vehicle is not listed below, contact Rosen Technical Support BEFORE YOU START to confirm

compatibility:

Buick: Enclave – Lucerne

Chevrolet: Avalanche – Equinox – Impala – Silverado – Suburban – Tahoe – Traverse

Pontiac: Torrent

GMC: Acadia – Sierra – Yukon

Saturn: Outlook – Vue

Note: The Rosen Unit backlighting is Blue/Green which matches most vehicles, however some vehicles use Red

backlighting. Rosen does not offer a GM Navigation System with Red Backlighting at this time.

DS-GM0710 GM Series

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 2

2 Identify The Vehicle Audio System Type

BEFORE YOU START you must verify the compatibility of the Rosen Navigation System. GM Vehicles contain a

number of different audio systems. The Radio included in this Kit is designed to cover specific GM Configurations.

The chart below will help you to properly identify the system in your vehicle.

Information Location and Type Standard Speakers Bose Speakers Bose Centerpoint

Non-Amplified Analog Amplified Digital Amplified

Window

Sticker

Descriptions

Options:

AM/FM, Stereo with CD

Options:

AM/FM, 6- Disc CD,

MP3 Stereo

Bose Audio System

Options:

AM/FM, 6- Disc CD,

MP3 Stereo, 9/10

Speakers, Subwoofer

Bose Premium Sound

System

Glove Box

Sticker

Codes

Codes:

UQ3

US8

US9

Codes:

UQS

U42

Codes:

UQA

Speaker Grill

Located in

A-Pillar

Logo:

None

Logo:

None

Bose

Logo:

Bose

Center Point

Product Selection Guide

Rosen

System

Part No.

and

Harness

Part No.

System Required DS-GM0710-Mxx DS-GM0710-Mxx DS-GM0720-Mxx

Main Harness Required

DP-GM0716 DP-GM0712 DP-GM0712

Optional

Parts

Rosen

Media Kit Harnesses

DP- 1062 N/A N/A

IPod Adaptor

DP-GM0718

IPod Adaptor

DP-GM0718

IPod Adaptor

DP-GM0718

Rear Seat Display

DP-GM0717 Included Included

Purchase from

GM Directly

XM Kit

GM17801150

XM Kit

GM17801150

XM Kit

GM17801150

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 3

3 Make sure you have the tools you will need

These common items are needed to complete this installation:

· Digital multi-meter (DMM)

· #2 Phillips screwdriver

· Panel removing tools

· 1/4” drive sockets are often needed for dashboard and trim disassembly

· Torx or Allen-drive wrenches if they are used on any panels you will be removing

· A CD or DVD in good condition for testing the system

Standard installation parts you may need include wire, wire ties, wire crimp connectors or solder, electrical insulating tape,

and foam tape. Installation of aftermarket automotive electronics also often requires access to special parts. It is a good

idea to have a source for these common installation parts.

4 Inspect the vehicle and plan your work

CHECK THE BATTERY

Test the battery voltage to make sure it’s fully charged and inspect battery terminals for tightness and any corrosion. This

only takes seconds and can save hours of troubleshooting later. A fully charged battery should have a voltage reading of

approximately 13.2 VDC.

5 Turn the Vehicle OFF or Disconnect the Battery

TURN THE VEHICLE OFF BEFORE STARTING

Be sure to turn the vehicle OFF before starting, and keep the vehicle OFF until the installation is fully completed BEFORE

the vehicle is turned on.

Note: Failure to follow these instructions may cause the AIRBAG FAULT SENSOR to become enabled. Fault

Sensors which have been enabled will require the Dealer Service Department to reset them.

Dealerships often charge a significant fee to reset the Fault Sensor.

New Vehicles RARELY have a fully charged battery. This can cause many system malfunctions.

Keep the Vehicle OFF while the Radio is disconnected to avoid a potential Airbag Sensor Fault

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 4

6 Remove the Interior Trim Components

You will need to remove the interior trim components prior to removing the factory radio. The following steps will help

guide you through this process.

Note: When removing the Interior Trim Components, use caution to prevent damage to the components. If you are

unsure about the removal process, consult the OEM Service Manual for additional instructions.

Note: Once the Interior Trim Components have been removed, be sure to inspect the clips for any damage.

Damaged part must be replaced before re-installation.

GMC Acadia Shown:

Step 1: Pull top of dash panel

towards you

Step 2: Carefully remove lower

portion of dash

Step 3: Carefully remove dash

panel and set aside

(Note: No need to

disconnect climate

controls!)

Step 4: Remove OEM Radio

Mounting Hardware

7 Remove the Factory Radio

You will need to remove the Factory Radio and prepare the Rosen Multi-Media unit for installation. The following steps

will help guide you through this process.

Note: Be sure to inspect all brackets and clips to ensure they were not damaged during the removal process. If any

brackets or clips were damaged, replace them prior to installation of the Rosen unit.

Note: Standard Bose radio/connections shown below

Step 1: Remove the OEM Radio

Step 2: Unplug the Electrical

Connections

Use Caution. See the OEM Service Manual for additional information on the removal process

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 5

8 Locate the GPS Antenna and iPod Interface

You will need to mount the GPS Antenna on the exterior of the vehicle. Mount the optional iPod Interface Connector in

the vehicle. The following steps will help guide you through this process.

Note: Please route the GPS harness away from other power harnesses in the vehicle. This will help to ensure

optimum performance of the GPS system.

Note: Please locate the iPod interface module in an area which can be serviced in the future.

Step 1: Mount the GPS antenna in

a location on the exterior of

the Vehicle

Step 2: Locate the iPod interface

connector for use by the

end-user

It is the installer’s responsibility to ensure that the safety equipment in the vehicle is NOT

adversely affected by installation of this system. Ensure that the routing of the harnesses does

NOT obstruct airbags, SRS or other safety devices.

9 Connect and Install the Rosen Unit

You will need to make the Electrical Connections and install the Rosen Unit. The following steps will help guide you

through this process.

Note: Use caution when locating the wire harnesses to be sure they will not be damaged when the Rosen unit is

installed.

Step 1: Remove transport screws Step 2: Connect the GPS

Antenna, Steering Wheel

Control and Power

Connections

Step 3: Connect iPod and

optional Camera/Backing

System harnesses

Step 4: Prepare the Vehicle side

connection harnesses

Insure that the video disable connection is connected as intended and working as designed!!!

Be sure to fully engage all connectors and prevent them from causing vibrating noises

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 6

10 Test System Then Re-Install Interior Trim Components

You will need to test system for full functionality prior to re-installing the interior trim components. The following steps will

help guide you through this process.

Note: When Installing the Interior Trim Components, use caution to prevent damage to the components. If you are

unsure about the removal process, consult the OEM Service Manual for additional instructions.

GMC Acadia Shown:

Step 1: Install Rosen Unit Step 2: Install the Dash Trim

Components as Needed

Step 3: Verify proper fit of dash trim Step 4: Verify unit operation

11 Touch Screen Calibration

The system was calibrated at the factory; however re-calibrate the system if the touch screen positions do not appear to

align with the buttons or icons.

Note: There are TWO Touch Screen Calibrations in the Rosen Navigation System. These Touch Screens are

calibrated independently as follows;

Calibrate the Primary/Radio Touch Screen –

Note: To Calibrate the Primary Touch Screen Operation of the unit (Radio, DVD, BT etc) follow these steps:

Step 1: Select Main from any

Screen

Step 2: Select SETUP on the Main

Screen

Step 3: Select CONTROLS on

the Setup Screen

Step 4: Select TOUCH SCREEN

and follow the on-

screen instructions

Use Caution. See the OEM Service Manual for additional information on the installation process

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 7

Navigation Touch Screen Calibration –

Note: The Navigation Calibration Screen is only available for a short time, after the vehicle is switched ON… To

access the Navigation Calibration Screen, Select NAV as soon as the System Self Test has finished.

Step 1: Start the Rosen Unit, and

wait for the Self Test to

completed

Step 2: Select NAV after the Self

Test has completed

Step 3: Touch the Screen

quickly, before it “Times

Out.” If needed, repeat

Steps 1 and 2.

Step 4: Follow the On-Screen

instruction to adjust the

calibration.

12 Installer Settings

Installer Settings Screen –

The Installer can enable and disable several option features of the Rosen Unit. To access the Installer Settings

screen, follow the steps below.

Step 1: Select Main from any

Screen

Step 2: Select the AV Icon Step 3: Touch the UPPER RIGHT

CORNER of the Screen

Enter “7253” and “Enter”

Step 4: Enable or Disable the

desired functions

Note: The following settings can be changed from this screen:

1. Enable/Disable the Rosen Blue Tooth Interface

2. Enable/Disable the Video Over-Ride connected to the Parking Brake (Use for testing only)

3. Enable/Disable RDS/RBDS feature

4. Enable/Disable Satellite Radio Interface

5. Reset the Factory Settings

Touch the Screen to

Calibrate

NOTICE: If this Vehicle is equipped with FACTORY BLUE TOOTH, the Rosen Integrated

Blue Tooth must be set to OFF in the Installer Setting Menu.

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 8

13 Pre-Delivery Test

You will need to fully test the system to ensure it is working and connected to the vehicle properly. The following steps will

guide you through this process.

Step 1: Initial Test

a. Reconnect the vehicle battery if needed

b. Start the vehicle (ensure that it is safe to do so)

c. Perform the following steps on the Multi-Media Systems to ensure proper operation:

 Turn the unit ON

 Select all available sources

o Select the Radio and test several stations

o Select the DVD and test playback of a disc

o Select the iPod and test music playback

o Select the Satellite Radio tuner if equipped, and wait for Sat Preview to start

 Test the Steering Wheel Controls

o If the vehicle is equipped, test all steering wheel controls

 Test the Backup Sensors

o If installed, test the sensors by placing a stationary object behind the vehicle (never test

the sensors by backing the vehicle into an object) Repeat this for each of the sensors

 Test the Navigation

o Select the Navigation and wait for the satellites to be located

o Confirm the location reported is your current location

 Eject the test disc

 Turn the vehicle off and wait for the unit to turn off

d. If the system does not function properly, reset the system by pressing and holding the reset

button located near the eject button

Step 3: Pre-Delivery Preparation

a. Start the vehicle (ensure that it is safe to do so)

b. Perform the following steps

 Calibrate the Navigation Touch Screen, if not already performed

 Calibrate the Primary Touch Screen, if not already performed

 Retest the Radio and general audio performance of the system

 Remove the protective films and clean the unit as needed

c. Place the Owner’s Information package in the glove compartment

14 Trouble Shooting Guide

No Operation –

There are a number of GM Radios which look identical but operate on different data protocol, you may experience

problems if the OE System was not properly identified or if the harness has become damaged. The Following Table will

help to Resolve Typical Problems.

Installed Rosen System Symptom Cause Solution

Any

Will not Turn On System is Turned OFF Press the Left Knob to turn the

system ON

Will not Turn On Vehicle is 11Bit Bus Check Compatibility Matrix at

the beginning of this Guide

Will not Turn On System is Locked UP Press & Hold the Reset for 10

Seconds

Will not Turn On Harness Damaged Check/Replace the

Main Harness

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 9

Audio Problems –

Because there are a number of Audio Options in the GM Product Line, you may experience problems if the OE Audio

System was not properly identified. The Following Table will help to resolve typical Problems.

Installed Rosen System Symptom Cause Solution

DS-GM0710-Mxx

No Audio Vehicle is a Centerpoint Use DS-GM0720-Mxx Unit

Use DP-GM0712 Harness

Low Audio Wrong Main Harness Use DP-GM0716 Harness

Distorted Audio Wrong Main Harness Use DP-GM0712 Harness

Over-Driven Audio Wrong Main Harness Use DP-GM0712 Harness

DS-GM0720-Mxx Volume Control Does Not

Respond Wrong Main Harness Use DP-GM0712 Harness

Blue Tooth Problems –

Because some vehicles in the GM Product Line contain a Factory Blue Tooth System, you may experience problems if

the OE Blue Tooth System was not properly identified. The Following Table will help to resolve typical Problems.

Vehicle Configuration Symptom Cause Solution

NO Steering Wheel Buttons No Blue Tooth Function on the

Rosen Nav

Installer Setting Menu

BT is Setting to OFF Set RES BT Setting to ON

NO Factory BT Button on

Steering Wheel

No Blue Tooth Function on the

Rosen Nav

Installer Setting Menu

BT is Setting to OFF Set RES BT Setting to ON

Don’t know how to Pickup or

End a Call Limited Function Available See Owner’s Manual / Quick

Start Guide

Factory BT Button on Steering

Wheel

Factory BT System does NOT

Respond

Installer Setting Menu

BT is Setting to ON Set BT Setting to OFF

Factory BT Reports No Phone

Paired

BT is Paired with Rosen

System – Not Factory

Set RES BT OFF and Pair with

Factory System

Customer wants to use Rosen

BT System

Installer Setting Menu

BT is Setting to OFF Change RES BT Setting to ON

XM Radio Problems –

Because some vehicles have an XM Option and others do not in the GM Product Line, you may experience problems if

the OE XM System was not properly identified. The Following Table will help to resolve typical Problems.

Vehicle Configuration Symptom Cause Solution

Factory XM

XM Says No Device Installer Setting Menu

XM is Setting to OFF Change XM Setting to ON

No XM Stations XM Antenna cannot receive a

signal

Move the Vehicle location to

outside in a clear area

No Audio XM Audio Harness is not

installed

Install Harness DP-GM0715 as

shown in Wiring Diagram

Limited XM Stations XM has not been registered Follow GM Instructions to

enable the XM Service

No Factory XM

XM Says No Device

No XM Tuner is Installed

Purchase and install the GM XM

Tuner Kit

P/N GM17801150

No XM Stations

No Audio XM Audio Harness is not

installed

Install Harness DP-GM0715 as

shown in Wiring Diagram

Limited XM Stations XM has not been registered Follow GM Instructions to

enable the XM Service

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 10

Service and Optional Parts List

Part Number Description Part Number Description

DP-GM0711 Quick Reference Guide DP-GM0712 Harness, Main Amplified/Bose

DP-GM0714 Installation Guide DP-GM0716 Harness, Main Non-Amplified

DP-GM1018 Harness, iPod Interface - GM DP-GM0715 Harness, XM Only Audio

DP-GM0717 Harness, Rear Seat Entertainment DP-1020-M11 Card, SD w/ maps

DP-1007 Harness, USB Adaptor DP-1001 Manual, Owner’s

DP-1003 Manual, Navigation DP-1062 Harness, Media Kit*

DP-1008 Harness, AUX Out* DP-1009 Harness, AUX IN*

DP-1010 Harness, Sensors/Camera DP-1023 Pin, Stylus

DP-1011 Harness, Dolby 5.1/Amp* DP-1035 Camera, Cylinder W/Mount

DP-1022 Antenna, GPS DP-1047 GPS Antenna Windshield Mount

NOTE: Items marked “*” are not compatible with all systems, contact Rosen Technical Support for specific compatibility.

Sourced from GM Dealerships

Part Number Description

GM17801150 XM Upgrade Kit - OEM

Wiring diagram

GM NON-AMPLIFIED SYSTEMS

Main Harness DP-GM0716

Radio Antenna GPS Antenna

OEM Vehicle Interface

DP-GM0716

Main Harness

Yellow, Battery +12VDC

Black, Ground

Fuse 7A

UART

OEM Vehicle Interface

XM Audio

Blue/Wht, Park Brake Ground

Blue, Reverse Trigger +12VDC

Optional – Interfaces

(Connection Not Req’D)

DP-GM0715

XM Audio Harness

iPod Interface

DP-GM0718

XM / iPod Harness

(Optional)

Replaces DP-GM0715

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 11

GM AMPLIFIED SYSTEMS

Main Harness DP-GM0712

Junction Connectors

Radio Antenna GPS Antenna

OEM Vehicle Interface

DP-GM0712

Main Harness

Yellow, Battery +12VDC

Black, Ground

Fuse 7A

UART

OEM Vehicle Interface

XM Audio

Blue/Wht, Park Brake Ground

Blue, Reverse Trigger +12VDC

Optional – Interfaces

(Connection Not Req’D)

DP-GM0715

XM Audio Harness

iPod Interface

OEM Vehicle Interface

DP-GM0718

XM / iPod Harness

(Optional)

Replaces DP-GM0715

:::: ::: ::: ::::

:::::::::::::

SatelliteRadio

BackupSystem

AUXInput

OnStar

AVOutput

RearOutput Alt

Installation Guide GM Series

Installation Guide DP-GM0714 IG Rev D

Page 12

www.RosenEntertainment.com

Rosen GM SERIES DS-GM0710 Installation guide

Brand: Rosen

Model: GM SERIES DS-GM0710

Category: Car video systems

Type: Installation guide

Download PDF

report

Rosen GM SERIES DS-GM0710 Installation guide

Rosen GM SERIES DS-GM0710 Installation guide

Related papers

Other documents