BLUENOTE BELVEDERE VILLA Owner's manual

Brand
BLUENOTE
Model
BELVEDERE VILLA
Category
Turntable
Type
Owner's manual
BLUENOTE®
Belvedere
Villa®
ITALIAN PRESTIGE FLOATING TURNTABLE
Owner’s Manual
MANUFACTURED IN ITALY
TEL.+39.0571.675005 FAX.+39.0571.675013
Belvedere Italian Prestige Floating Turntable
Table Of Contents
- Congratulations & Introduction 3
- Box Content 4
- Construction Features 5
- Unpacking & Assembly 6
- Installation & Positioning 7
- Operating the Belvedere 8
- Specifications 8
- Warranty, Customer Service & Warnings 9
- Troubleshooting 10
- Troubleshooting 11
- F.A.Q. Adjustment 12
VERY IMPORTANT: Please read the following instructions carefully before installing your
Bluenote® Turntable
Belvedere Italian Prestige Floating Turntable
Congratulations
Thank you for having purchased a BLUENOTE® product.
Introduction
With BLUENOTE® products you enter a new dimension.
BLUENOTE® is the new way of listening to music. BLUENOTE® is a
range of products of prestigious and sophisticated Italian design
featuring unique and innovative technical and aesthetic characteristics.
The materials used for the BLUENOTE® turntables are of the highest
quality and they are all assembled and tested by hand, one by one. No
photos or technical descriptions can adequately convey the quality of
BLUENOTE® turntables or the pride of owning one.
The turntable boards are made entirely from skillfully crafted sheets of black polished acrylic. The platter itself is in extruded
acrylic “tuned” by an amazing 9 counterweights in gold plated brass. The pivots and bearing are made in aluminum brass
and de-coupled stainless steel with Teflon®. All the applied details are in 6082 aluminum alloy or gold plated brass and all
are turned from solid blocks. The tailor-made belt is manufactured from a special low-stretch (35/40%) resin which allows for
maintaining the typical advantages of turntables with belt drives but also allows for adding characteristics of drive speed and
power that cannot be reached with conventional turntables. The synchronous motor is made to 24 pole specifications for
further enhancing the performance.
In a word, the Bluenote® ® range sets a new standard of reference in the turntable category.
Congratulations & Introduction 3
Belvedere Italian Prestige Floating Turntable
Contents of Packaging
- 1 TRANSPARENT ACRYLIC BOARD, PRE -PERFORATED AND THREADED.
- 1 POLISHED BLACK ACRYLIC BOARD COMPLETE WITH ARM BOARD (STANDARD SME) AND PERFORATED SUPPORT FOR
BEARING/SPINDLE BOTH SILVER ANODIZED ALUMINIUM.
- 1 SYNCHRONOUS CYLINDER MOTOR IN ANOIDIZED ALUMINIUM
- 1 DETACHABLE AC POWER CHORD.
- 1 STAINLESS STEEL SCREW FOR ANCHORING THE MOTOR TO THE TRANSPARENT ACRYLIC BOARD.
- 1 MOTOR PULLEY COVER IN SILVER ANODIZED ALUMINIUM.
- 1 PULLEY IN DELRIN (OPTIONAL IN MOST COUNTRIES AN ADJUST ABLE ALUMINIUM ONE IS AVAILABLE) 33-45 rpm.
- 1 BRONZE PLATTER BEARING COMPLETE WITH WHITE ARNITE SCREW FOR PLATTER HEIGHT ADJUSTMENT.
- 1 ANCHORING BOLT FOR BRONZE PLATTER BEARING.
- 1 CARBON STEEL TEMPERED POLISHED SPINDLE SPINDLE SPLIT IN 2 PARTS TO CLAMP THE TURNTABLE PLATTER.
(THE BELVEDERE SPINLDE IS 60 TIMES STRONGER THAN REGULAR CARBON STEEL ALLOY).
- 2 BRASS THREADED BARS FOR FRONTAL ALUMINIUM SPRING SUPPORTS COMPLETE WITH RUBBER SPACER RINGS.
- 1 THREADED BAR IN STAINLESS STEEL FOR REAR ALUMINIUM SPRING SUPPORT COMPLETE WITH RUBBER SPACER
RINGS.
- 2 CONICAL SPRINGS FOR FRONT BLACK ACRYLIC BOARD SUPPORT
- 1 RED MARKED CONICAL SPRING FOR REAR BLACK ACRYLIC BOARD SUPPORT
- 3 BOLT SHAPED SPRING SUPPORTS.
- 3 SILVER ANODIZED ALUMINIUM FEET FOR TRANSPARENT BOARD.
- 3 SILVER ANODIZED ALUMINIUM THRADED BAR COVERS.
- 2 SILVER ANODIZED ALUMINIUM FRONT SIDE SPRING COVERS.
- 1 GOLD PLATED BRASS REAR SIDE SPRING COVER.
- 1 PLATTER IN BLACK SATIN EXTRUDED SUSTARIN® WITH 9 GOLD PLATED WEIGHTS
- 1 70 Shore ELASTICITY DRIVE BELT
- 1 RECORD ANODIZED ALUMINIUM CLAMP
- 1 OIL VESSEL FOR PLATTER SPINDLE
- INSTRUCTION BOOK AND WARRANTY CERTIFICATE
Contents of Packaging - 4
Belvedere Italian Prestige Floating Turntable
Construction features
This section describes the special features of the BELVEDERE turntable, the construction features, the reasons for the technical choices and
the originality of the design.
- BELVEDERE is a floating on Harmonic Iron springs turntable that, like all the turntables of the Bluenote-Villa line, uses a board made in
black high -density polished acrylic obtained via “polymeric melting”, as a main support for the platter and arm and a transparent board,
also in acrylic, as the board support where the motor cylinder and support feet are housed.
- The black board is fully curved for increasing the structural rigidity and non-deformable properties.
- The Transparent board has 3 machine worked aluminium height-adjustable feet with a semi-conical shape with central grooving for
ensuring greater insensitivity to vibrations. Each foot has a recessed spike may be used to couple rigidly the turntable on its shelf.
- The turntable platter is in “extruded” Sustarin®, an even ‘deafer’ material that cannot be polished but is ideal for the intended use. Below
the platter are 9 gold-plated brass weights, which increase the peripheral inertia of the platter and thus further improve the rotational
regularity and stability.
- The spindle is probably the best the market has to offer today. 60 mm long (one of the longest spindles in existence), it is made with top-
of-the-range materials and machined with CNC lathes, than rectified to achieve super high-level tolerances. A large longitudinal groove is
located on its axis, which allows the lubricating oil to run in constant manner.
- The longer spindle eradicates any pendulum effect and distributes the inertial energy along its entire axis, completely annulling any type of
lateral friction.
- When the turntable is new the spindle will tend to “clean” any residual dirt in the bearing (which no preventive cleaning is capable of
completely removing). In this way even the tiniest residual friction built up after only a few dozen hours operation will be completely
eliminated.
- The bearing that houses the spindle is made entirely in bronze and has a screw in WHITE ARNITE® located on the bottom that allows for:
- Perfect coupling.
- Adjustment of the VTA carried out directly on the turntable board!!
- The possibility of eliminating virtually every type of friction that could build up during the years with conventional
bearing/spindles.
- Moreover, the bearing is threaded on the outside (the only one of its kind) in order to be tightly anchored to the board of the turntable on
its own axis. This allows avoiding the use of glue and anchoring screws that would lock the bearing out of alignment and prevent a fully
rigid and precise coupling.
- The bearing is locked onto a brass ring support specially designed to obtain a perfect plane and at the same time it decouples from the
turntable board.
- The clamp (not screwed) that weighs 300 grams and is made in anodised aluminium has been chosen thanks to its excellent sound
performance.
- The motor, which is AC (synchronous) 24 pole with an extremely high coupling coefficient and very low noise, is moved by a custom
made capacitor. The motor that has a 3 mm stainless steel spindle is directly coupled onto the acrylic board thru a special brass system of
rings able to reduce vibrations at its best.
- The pulley is made in DELRING/ALUMINUM and need to be pushed/locked with Allen bolts onto the motor spindle.
- N.B.: acrylic and Sustarin® (That is an acetamide polymer) are inert, especially rigid materials which makes them ideal for absorbing
vibrations. With their extremely elevated technical and sound characteristics these materials are easily subjected to small surface scratches.
Particular care must therefore be paid to clean the platter and the turntable with a very soft cloth. Avoid the use of any type of solvent.
Despite not making use of mats, the platter will not ruin new vinyl records and creates a perfect coupling with it.
Construction Features 5
Belvedere Italian Prestige Floating Turntable
Unpacking & Assembly
This section describes how to assemble and install your BELVEDERE turntable. The instructions are purely descriptive and necessarily generic.
If you have any doubts or difficulties with this procedure please contact your retailer who will know how to assist you:
1) Open all the cartons inside the main box and look that all the components listed in the “content section” are present.
2) Screw down the three threaded bars in the specific holes of the transparent acrylic board. The 2 made of brass bars must be housed in
the front holes, the Stainless steel one in the rear holes. The threaded bars must protrude from underneath the transparent acrylic
board about 10 mm.
3) Screw up the silver anodised aluminium feet on the threaded bars onto the lower part of the transparent acrylic base.
4) Insert the silver anodised aluminium threaded-bar covering tubes into the threaded bars on the upper part of the transparent acrylic
board.
5) Screw up the bolt shaped spring supports with the faced up (bolt shape) onto the head of the threaded bars and fit the conical springs
onto them. The eventual red marked spring must be positioned on the rear support.
6) Install the bronze bearing inside the centric hole on the round aluminium board located on the shaped black acrylic board and anchor
it tightly with the bolt supplied.
7) Gently lay the black acrylic board onto the pre-installed springs finding the perfect centring inside the holes of the board itself.
8) The cylinder motor must be inserted into the hole of the black board and locked onto the transparent board using the stainless steel
screw supplied thru the present slot. The screw MUST NOT be tightened by force in order to prevent the transparent board from
breaking. Position the switch in the most accessible place for being turned on and off (typically left side).
9) Pass the power supply cable of the motor through the specific hole located on the transparent board and connect the motor and the
AC plug to the wall.
10) Press down the self-centring Delrin pulley until it fits into the motor shaft. It is important to press it in a vertical direction not too
firmly. Take care not to knock the pulley board against the motor body.
11) Get the 2 parts Carbon Steel Platter Spindle and the Sustarin® Platter.
12) Clamp the Platter into the 2 parts Carbon Steel Platter Spindle screwing out the tip part of the Platter Spindle, inserting the larger
part into the centric hole of the Platter (bottom side) and re-screwing down the Tip of the Spindle into the Platter till the clamping
effect is very strong.
13) Wet, just a little, the Platter Spindle part gets into the Bronze Bearing with the oil supplied and push it down, very gently, into the
Platter Bronze Bearing screwed on the Turntable board.
14) Before spinning the Platter pay extreme attention to adjust properly (also as you like most aesthetically) the height of the platter by
moving the head bolt shaped ARNITE white screw at the bottom of the Platter bronze bearing. Please Note: the ARNITE screw,
even though is treated with a high density silicon grease to seal the threaded grooves, can leak a little oil once the spindle is inserted
in the bronze bearing due to the super air pressure create because the very strict tolerances between the Spindle & the Bearing.
Eventually simply clean up the excesses oil. Once the Spindle finds the right internal position the oil may not leak any more.
15) Once the Platter/Spindle is positioned properly (this operation may take some time due to the very strict tolerance in between the
Platter Spindle & Bronze Bearing), wrap the Belt supplied around the Polyvinyl Platter and the Pulley, in the wanted speed position:
Upper smaller pulley groove is 33-1/3rpm and lower larger pulley groove is 45rpm.
16) To finish this assembly operation level the black acrylic board to a perfect flat position and connect the AC plug.
17) The Belvedere is supplied with a tonearm collar and an adaptor to be used with several units (including all Bluenote tonearms). Ask
your dealer for better info.
Unpacking & Assembly 6
Belvedere Italian Prestige Floating Turntable
Installation procedure
This section describes how to install your BELVEDERE. The instructions are purely descriptive and necessarily generic.
- Always take care when positioning the device, which, within the possible limits of your listening environments, should be on a solid and
firm board in an area allowed by air circulation.
- The turntable is supplied in series with 3 height-adjustable anodised aluminium supports that act as the anti-vibrating feet. By laying the
BELVEDERE on different shelves the sound characteristics may be different. We recommend high mass support boards not affected by
external vibrations trying to choose the best solution, which also fits in with your needs.
- Before carrying out the installation it will be necessary to level the turntable platter even using a simple sprit level. The 3 feet only
facilitate the positioning and allow the best possible coupling with the supporting board.
- The belt supplied must be positioned on the external perimeter of the platter. Check that the speed is perfect. Even though Pulleys and
Platters, have a centesimal precision the electrical power supply in your country may have output variations of the AC frequency (50 Hz
or 60 Hz) that slightly alter the rotation speed of the AC synchronous motors. In this case you’d need our adjustable aluminium pulley, or
a controlled external AC power supply (both available in most countries as optional)
N.B.: The speed variation tolerances, even in the case of your current supplier provides an incorrect frequency, are extremely small, therefore
any variations always constant) would be limited. A frequency computerised generator (optional) or a motor pulley with a variable diameter
(supplied) would be necessary in this case. Less than 2% variations are completely un -hearable by human ears.
Positioning the Belvedere
Your BELVEDERE turntable has been designed for sheltered Hi-Fi systems. It must be protected from any eventual variations in temperature
and humidity. Avoid using in the vicinity of radiators or other strong heat sources, electrical and electronic motors, switched on mobile phones
etc.
The location in proximity of other audio components is not theoretically critical, but you should nevertheless pay attention to this.
The levelling and positioning on a solid, firm board, as explained in the previous chapter, are fundamental elements to ensure the maximum
sonic performances.
Installation & Positioning 7
Belvedere Italian Prestige Floating Turntable
Operating conditions
Once you have connected the power supply cable to an AC current power plug as well as the cable supplied with the tonearm that you will
previously have installed and connected, your BELVEDERE will be ready to use.
PLEASE NOTE.: Check that the correct acceptance voltage is indicated on your turntable. Incorrect voltage will prevent your
BELVEDERE from working properly and could risk causing irreparable damage.
WARNING: Never turn on the turntable while any parts are disassembled as contact with the high voltage inside the
BELVEDERE turntable could be fatal.
33 1/3 rpm or 45 rpm
By positioning the belt in the smaller groove of the synchronous pulley motor, the BELVEDERE turntable be set at 33 1/3 rpm, while in the
larger groove it will be set at 45 rpm. This positioning must be carried out manually.
The pulley may be covered by a Jewellery Gold Plated cover available as optional.
Turning on
The On/Off switch is located on the silver anodised motor cylinder screwed to the transparent acrylic board. Once the switch has been turned to
ON (1) the turntable will start working at the speed hand selectioned.
Specifications & Technical features
n Wow and flutter : 0,03
n Rumble: -82 db
n Speed: 33 1/3 and 45 RPM +/- 0,1% - rapid manual changeover
n 70 shores elasticity black drive belt
n Dimensions: width 550 mm; depth 400 mm; height 200 mm.
Operating - Specifications 8
Belvedere Italian Prestige Floating Turntable
Warranty Certificate
The warranty certificate is enclosed separately and to be valid must be completed fill and returned to Bluenote factory or the official
distribution. In all countries where there is an official distribution network, the dealer must stamp the warranty certificate. In compliance with
the laws in force, the dealer may modify the official Bluenote warranty certificate wholly or partially without notice and without further
mention being made in this instruction manual.
Customer Service
All BLUENOTE products are the result of meticulous technological research, and consequently their correct functioning is guaranteed. In spite
of this it is possible that problems may emerge which non-specialist users cannot resolve. In this case, contact your dealer who will advise you
on how to resolve the problem.
Do not return any object directly to the factory or to the national distributor or without being authorized to do so. In such cases both
BLUENOTE and the distribution agents operating within your territory decline responsibility of any kind.
PS. The photos reproduced here refer to the Belvedere Turntable, but parts and descriptions may vary from the product on sale without notice.
Warnings
1. Do not disassemble any part of the product.
2. Do not use any part of the product for other purposes.
3. For service and problems of any kind, contact qualified personnel.
4. Protect the product from rain and humidity and keep away from heat sources, electric and electronic motors etc.
Warranty Certificate – Customer Service – Warnings 9
Belvedere Italian Prestige Rigid Turntable
Troubleshooting
SYNPTOM DESCRIPTION CAUSE REMEDY
BELT NOISE DURING
PLAY (GREEN BELT)
The Green Belt makes a
noise during playing
• Because its low elasticity and
the presence of ceramic particles the
characteristics of the green belt make it
noisier than usual rubber black belts; It
does not affect the sound
• If a quieter belt is requested
ask your local dealer for one of the
newest Bluenote Black Rubber Belts
BELT WOBBLING DURING
PLAY (GREEN BELT)
The Green Belt wobbles
during playing
• Because its low elasticity and
the presence of ceramic particles the
characteristics of the green belt make it
wobbles a little around the motor pulley;
It does not affect the sound
• If a not wobbling belt is
requested ask your local dealer of the
newest Bluenote Black Rubber Belts
MOTOR HEATING The Motor warms up too
much
• AC synchronous motors as
the ones used by Bluenote normally
warms up to 50° Celsius without creating
any problem
MOTOR NOISE The Motor produces a low
scraping noise during
playing
• The pulley’s shaft slightly
touches the motor go ld plated cover
• Gently lift it up a bit
unscrewing the hex bolt of the pulley
The Motor produces a
scraping noise during
playing
• Your turntable has a serial
number before the 11650
• Ask your local dealer to
change the internal capacitor filters the
AC voltage
OIL POORED FROM
BRONZE BEARING
Oil drops come out the
bottom Platter Bearing
when the Platter Spindle is
inserted
• The super high pressure created
by the strict tolerance of the
Bearing/Spindle system can let some oil
drops come out from the bottom of the
Platter Bearing
• Clean it up, the oil will never
comes out again once the Platter
spindle is perfectly positioned into the
Platter Bearing
PLATTER BENT The Platter looks bent on
the Turntable board
• Clamp the Spindle tip into the
above side of the platter screwing it
strongly using a metal pin to get into the
tip hole
•
• The Turntable Platter Bearing
Bolt is 10mm thick having a serial
number before the 11500
• Ask your dealer to have the
new thicker Turntable Platter Bearing
Bolt
PULLEY WOBBLING The aluminium adjustable
Pulley evidently wobbles
• • With the Allen key supplied
adjust the 2 hex bolts fix the pulley on
during turntable play
mode
the motor spindle until you find the
perfect on axis spinning – a PERFECT
on axis spinning must be found with a
bit of practice eventually marking up
one of the 2 hex bolts to know which
one needs to be tighten more. Be
careful not to tight the hex bolts to
much, the pulley threaded hex bolt
holes could be damaged
SPEED VARIATIONS The turntable speed vary
up and down continuously
• [The AC synchronous motors
speeds can be affected only by the
HERTZ or eventually by the dimension
of the pulleys
• Any speed variation with a
fixed pulley dimension is caused by your
AC power national supplier or by your
home AC system, check it out
SPINDLE (of the Platter):
CLAMPING THE
PLATTER SPLIT SPINDLE
TO THE PLATTER
The Platter wobbles on its
edges or it vertically
shakes during playing
• Clamp the Spindle tip into the
above side of the platter screwing it
strongly using a metal pin to get into the
tip hole
•
• If the strongly clamp screwing
of the spindle tip does not fix the platter
enough, the platter hole is been enforced
after final user assembling
• It needs to be substituted by
your local dealer
Troubleshooting 10
Belvedere Italian Prestige Rigid Turntable
SYNPTOM DESCRIPTION CAUSE REMEDY
SPINDLE (of the Platter):
INSERTING THE
PLATTER SPLIT SPINDLE
The Spindle does not fit
into the Platter Central
Hole
• • Unscrewing the tip, split the 2
pieces Spindle and fit the bottom part
of the spindle into the platter through
the gold plated weights side, clamp the
Spindle tip into the above side of the
platter screwing it strongly using a
metal pin to get into the tip hole
SPINDLE/BEARING (of the
Platter) NOISE
The Spindle makes noise
during platter spinning
• The Platter Bearing/Spindle
system are very dirty making a too strong
friction
•
• The Platter Bearing/Spindle
system are new and they need a break in
time to sweep out all the internal
unwanted particles
• After a couple of weeks of
playing clean and re-wet them with
some fresh oil supplied
SPINDLE (of the Platter):
TIP OF THE DIAMETER
The Records hardly fit into
the Platter Spindle Tip
• Bluenote Platter Spindle Tips
have a 7,2mm of diameter that is the
recognised international standard but
many records are wrongly moulded
• Sorry you need to enforce the
record into the Platter Spindle Tip
SWITCHING ON/OFF
BUMP
The turntable bumps any
time is switched ON or
OFF
• It is important to notice that it
does not produce any risk even if the
bump is high, but if you have a turntable
with a serial number before 11650
• Ask your local dealer to add a
proper ceramic capacitor able to filter
such noise
SPEAKER HUMMING
PROBLEMS
The speakers hum when
the turntable is connected
to the system
• The Turntable CAN NOT
makes any noise hearable into the
speaker by itself
• Eventually a tone arm cable
problem can occur; please check other
ways out
TURNTABLE (THE) DOES
NOT START WHEN THE
TURNTABLE IS
SWITCHED ON
• The AC turntable plug is
disconnected from the AC wall plug
• Connect it being sure that the
AC wall plug works
The Turntable just does
not start
• Have you wrapped the Belt
around the Pulley and the Platter
properly
• If not just do it
• The electrical connection inside
the turntable could be damaged
• Contact your dealer for
assistance
When the turntable is
switched on it does not
start automatically and the
motor makes a vibration
• The Belt is too slack and does
not produce the necessary friction with
the pulley
•
When the turntable is
switched the belt wraps off
the platter edge
• The level of the black curved
board of the turntable is wrong, higher or
downer than the standard position
• Adjusting the height of the
black board through the spring supports
rotation helped by their bolt shaped
heads. Approximately the regular
position is found when spinning at 33
rpm the belt is cantered on the platter
edge. The approximate right position
of the spring supports are: (considering
the turntable front view) LEFT at the
same level of the tip of its threaded bar;
RIGHT 5mm higher than the tip of its
threaded bar; BACK 8mm higher than
the tip of its threaded bar
When the turntable is
switched on it does not
start automatically
• The Platter Bearing/Spindle
system are very dirty making a too strong
friction
•
Troubleshooting 11
Belvedere Italian Prestige Rigid Turntable
F.A.Q.
Adjustment
BELVEDERE Turntable
ACTION DESCRIPTION HOW TO ADJUST IT
DUST COVER FRICTION
ADJUSTMENT
• The Dust Cover is hard or slack
during open/close adjustment
• Adjust the single screw present on each hinge till
you reach your proper wanted friction
LEVELLING THE TURNTABLE • The Turntable is not levelled • With a spirit level take care of levelling the
platter on its vertical and horizontal lines.
Adjust the height of the black board through the spring
supports rotation helped by their bolt shaped heads.
Approximately the regular position is found when spinning
at 33 rpm the belt is cantered on the platter edge. The
approximate right position of the spring supports are:
(considering the turntable front view) LEFT at the same
level of the tip of its threaded bar; RIGHT 5mm higher
than the tip of its threaded bar; BACK 8mm higher than
the tip of its threaded bar
• The Turntable is not levelled • Be sure that the turntable layer is enough solid
and rigid to support the weight of the turntable easily
SPEED ADJUSTMENT ON THE
ADJUSTABLE ALUMINIUM PULLEY
• The aluminium adjustable
pulley doesn’t spins at the right speed
• With the help of a “coin” screw clockwise or
anti-clockwise the pulley’s internal cone to increase
(clockwise) or decrease (anti-clockwise) the speed.
Check the right speed with a proper stroboscope
SPRING ADJUSTMENT • It is hard to adjust the springs
inserted in the bolt shaped supports bear
the black curved board
• To help the adjustment of the springs through
their bolt shaped spring supports, slightly lift the black
board (few millimetres) with a finger during the rotation
movement of them.
VTA ADJUSTMENT • VTA tone arm is not adjustable • The arm board collar hex bolts are screwed into
the collar too much and do not let the arm shaft gets in it;
unscrew the hex bolts properly
• VTA tone arm is not adjustable • The adaptor has to be used and lift but the collar
keeps it down; Unscrew the collar hex bolt, find the proper
adaptor height and re-fix it again
• VTA tone arm is not adjustable • The tone arm shaft is too big to get into the
collar or the supplied adaptor; ask your local dealer to have
a custom made collar fit such arm
• VTA tone arm Hang Over is
hard to adjust
• With the Bluenote arms or Rega standard shaft
ones, rotate the adaptor at the necessary height, till the
proper Tonearm Hang Over is been found
CLEANING THE TURNTABLE • The Turntable is dirty and needs
to be cleaned
• With EXTREME care use ONLY pure alcohol
and a very soft 100% cotton cloth to sweep dust and stains
out.
Any acid or not extremely soft cloth will irreversibly
damage the turntable fine aesthetic.
Do not use any alcohol to clean the turntable anodised
label, pulley and motor spindle. Only dry cloth is allowed
F.A.Q. & Adjustment 12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

BLUENOTE BELVEDERE VILLA Owner's manual

Brand
BLUENOTE
Model
BELVEDERE VILLA
Category
Turntable
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents