Operator's Manual
1
Model No,
CAUTION: R:ead,understand and follow
aH Safety Ruies and O#erating #sstructions
ir_this manua_before using this #_oduct,
• Safety
- Warranty
• Features & Operation
• Maintenance
• Espa_o| pg, 13
Sears, Roebuck and Co,, Hoffman Estates, IL 60179 U,S.A,
V_s_toer Craftsman webs_te: www.craftaman,eom
ONDYEAR FULL WARRANTY ON CRAFTSMAN PRODUCT
[f th_sCrsflsmar_ pf_uct fails @e to a defect in mater_a_ a_wo_kme_ship ,_thin one
yt_.a[from _he date d pUrcha_a RETURN IT TO ANY SEARS STORE OR OTHER
CRA_SMAN OUTLET IN THE UN_ED STATES FOR FREE REPLACEMENT,
ff _¢s @aftsman prcyjuct is used _a_comme_cia_i of re,tat purposes this war_a_ty
appk_s bf On_y90 days f_om Be date d pu[chase.
This warranty _ves you s42ee}f_cle_ _ghte and yo_._may alse have oc_e_' r_ghts
whirl vary from s_ate t9 s_ate
£_a_ R@_b_¢k aRd CO,. Dept 8t 7 WA Hoffma_ Estates _L 60179
SAVETHESEINSTRUCTIONS! ;READALL INSTRUCTIONS!
ZWARNWNG:]
* Fa}/_fe te comply with ebfma_ie_ h _his man,ual or to heed product _amk_g !abe_s
may result e persor_al sissy or property damage
. Sfu@_ a.ede_s_and a_d fe t_,, air 1he hs_ruetioes be_O_eopefa%g this device
, ONLY use iack De a _rd #ave_s_dace tP_I iScapable d sap_xsrfl_'tgthe veh c_e
, Lift o_ty on area5 d vehicle as sT,ecBed by the vehicle maeufacture_
, ALWAYS u_ tieodowe straps to secure the sehicb to the jack.
NEVER me_e vehid_ with jack if straps are no_ ie pb_._eef secde.
* ALWAYS use the height bck bar wher_ the vehic#e is _aised te preve_l the
vehicb from dropp _g accidental y;
, ALWAYS b_e[ the vehicle to the bwes_ _ss_b/e jack p_itk)_ BEFORE
attempting to d@_ or mere it
"DO NOT make az_yalte_atlees te this Feduct
* the _a_ bebre each a_,
* DO NOT u_ }f bak_g flukJ andor bre_n_ beret c_a@ed of ether'¢4se dama_J
pass ale tiered
* Immediately afte_t raiat#g vehicle, ensure that Height Lock Bat is engage&
* ALWAYS _ar safe_y _@e_ _rat_ng ths predict.
iaek it could cause serie_s badly ieju_y_
, Open the re/ease valve by pressing down on the re_easepeda_(_
(see Fig. t and 2)
• Remove the oil fi_ plug__(seeFig i).
• Pump the foot peda_ (_ (see Fig I and 2) 6 to 8 times to release any
pressurized air that may be trapped in the oi_reservoir (hydraulic system)
- Be sure oii leve_is just be_owthe threads in the ot fi_ip_ughole if oi_needs
to be added fo_r_,_the instructions on page 9.
• Replace and tighten oi_fi_ plug.
This iack (see Figs_1 IA IB and 2) has specia_ builHn featu[es that make
it idea_for pedorming minor repairs oil changes cleanups and more.
These features include:
, 1500_pound load capacity to lift most motor_cles and ATVs.
, A fasbaction hydraulic pump with toot pedal(J_see Fig2) for easy lifting
from 51/sto 17 inches above front ofiack base Twoadapter p/ares,sg/d
separate_/(see Fig.1A) are availabieto allow lilting to 19 nches above
front d jack base.
- 3 position Height Lock Bar provides positive locking at three lift heights:
1t _4 in., t4 1/_in. and 16 I/2 in (see Fg.1)_
iMPORTANT: Upon raising vehic[e_the jack must IMMEDIATELY be locked
into one d the three lift heights.
* Precision controlled _ootrelease_(F g.2) for Iowedng the vehicle
, Can be used as a dolly to move your vehicle to a convenient location
for working or storage.
, T:Handie(Fig. 1) for added controlwhendotMng veh}cleinto workngor storage _a_ion.
, The jack a_soincludes h*_ol_inch wide × 15 foot long ratchetihg tie-down
straps (see Rg 1B) to help secure the vehicte.
, The jack has adiustab_e locking screws and _ockingcasters
to increase stability (see Fig°t ).
, Purchasetwo2richheightadiustmentadapterplates(seeFig.1A),
soldseparately,toadd2inchestothemaximum_iftheightofi6V2inches
toaccommodatehigh-chassisdi_bikesthatrequirean18V24nchheighL
• _nc_udestwo 1*inch wide x i 5-ff. _ongratcheting tie_dowr_ straps
(see Fig. 1B and F]g_4A)_
Fig,IA
i_l.,<......................................._.i__ j ............/so_di_..._p,_te_yt
Lift
Saddles
FootPedal
Release P_al
Base
Locking Wheels Height Lock Bar
Locking Screws
Page is loading ...
2. insert Foot Peda_Arm @ into the sleeve of Hydraulic Ram _ and
secure wth M8 x 12 Hex Bolt (4)_
3, Attach Height Lock Re_ease @ to Height Lock Bar using 2 Spdng
Washers G8 (1)AND 2 Nuts M8 (2),
4, Attach T-Handle _to ConnectiRg Rod _ with Cotter Pin (3),
5. Make sure that ali connections are tightened thoroughly.
TO RAISE THE VEHICLE (see Figs 2_3)
1,P_ace_ck on a hard ievef surface
2. To a/'_id item from slippingdu#ng tP_
_aisingo_ration ONLYlitton points d
vehicle ed by vehlcie manufacturer F_t Pedal
in the veh_sWsoperatoCsmanual
under the vehicle s liftpoint.
f@t on tab marked LOCK_AL_YS @ec£ to_ sure #_atthe _dd_e and the
vehicle are p@sit£_edco_Tect_yBEFORE raisingthe }8_k
5, Use Fc_t Peda_to raisevehicle,Pump Foot Peda}unti_tip o_Height L_;_ Bar
m_s past desired_c_kpositbn ridge The tipof the Height LockBar wit!sink
ilto positionjust behindthe ddge.Depress releasepeda_s_ight_ysothat #'_etip
movessaugtya_inst _idge
& Applyt}e-downstraps(seepage7, Secudngthe'_,Lehicle)once_hic_e has been
raisedtothe desired workinghe_ht Thoroughlytighten thetwotie-®wn straps.
7, Stabiiize _oaded on a hard surfacefor maximum balance by adjustin9
_ockingscrews
TO LOWER THE VEHICLE, (see Fig, 2)
1, Raise the iack s_ighflyand pull back on the Height L_sk Re_easeto release
2,Fastenthe HeightL_k Retease@ totheQip @_
3. Pressthe Relea_ Pedal_very gently tolower the Saddle_)and vehicle
6
1_ | Tie-downstraps wi!lbecomeI_se and vehiste wilt
I
be releas_i upon loweringthe vehicle
SECURING THE VEHICLE with the two 1-in, x 1_,
Rateheting Tie-Down Straps (s_ Fig, 4, 4A)
Fig, 4 Release La_chC
Top view "OPEN Position
3, Tighten the strap by ratcheting the handle back and [orth until the vehicle
is sec_Jretn order to keep the strap in position while t ghtening, may be
necessary to take up _heexcess slack by hand unti! the strap is tighL
4, To_ockratchet, p_aceHandle @ in the ciosed position
to the veh c/e, DO NOT over-tighten strap,
Fig. 4A
High,.chasss moto_yde
secured onto iack wilh the
2cinchadapIer p_ates
sold separately
andthe two ratche_in9
fie_.>wn straps
RELEASING THE VEHICLE FROM THE TWO RATCHETING
TiE-DOWN STRAPS (see Fig. 4B)
Fig 4B
Release Latch C
"CLOSED _Position
1. Hoid the ratchet in one hand and with the other hand puli back on
Release Latch @o
until the toad re_eases.
[_CAUTION:j The VEHICLE witireiease atthis point.
& 'Toremovestrap pu_/up on _atchetand slidestrapout of Spindle _.
1 DO NOT use the two tie down straps for towing vehicles or to
ho_dor suspend human weight.
2. DO NOT use pliers or any other tools to operate the ratchefing
handte _, (see Fig. 4B}. Use hand power only:
3 Protect strap webbing from sharp edges heat and acid. Replace
strap webbing if t iscut worn or damaged, hspect strap webbing
hooks and hardware before each use.
(seeFig.1,2)
TOADDHYDRAULICJACKOIL
the oi_fill plug DO NOT ALLOW dirt o_debris to ente_ the system
TO REPLACE HYDRAULIC JACK OiL
° Open the release valve by pressing down on the re_ease peda_
Unscrew and remove oil fil_plug.
- Turn entire jack over so that a_ d the old oi_will drain out d the oi_fiHhole.
NOTE: When draining oil use a proof container and ALWAYS fo_ow ALL
local and state waste disposa_ guidelines
* After a_!of the oid oil has drained out d the jack, turn the _ack back e/vet to a
DO NOT ALLOW dirt and debris to enter the system
-Repiace and tighten oil fili piug.
iMPORTANT: When adding or replacing oH, ALWAYS use a goed
grade d (SAE 5 W) hydraulic jack oi_ NEVER use brake fluid, alcehoi
glycerin, detergent motor oi$or dirty oH d any kind Improper oit usage
will cause serious internal damage to jack.
LUBRICATION
, Use a good grade e_lubricating ell on a_ moving parts when needed
STORING
, When iack is not in use or when storing the jack,
ALWAYS have the lift saddles in the lowest (downi_position
RUST PREVENTION
Check power unit (hydrau}ic ram} see pa_s _istFig 2 _etter_) page 5
every two monfhs or sooner based on use for any rust or corrosion
Clean and wii_ down with oil cloth.
Maximumloadcapacity: 1500ibs(681kg,}
_ckingPositions: 1t3t4in,t4114inand
161/2in
Size: 351_x17xt4inches
Weightwithoutthetwotie*downstraps
andthetwoadapterplates(soldseparately):_77_bs_
PROBLEM
Jack will not
ftft to full
height
CAUSE
1.Airin hydraulic
system
2,Release valve is
stuck
t Oil ieve/is tow
2. Airin hydrau%
system
1,Airin hydraulic
system
2, Dirtyoit
I, Excessiveweight
2 Oil level is bw
SOLUTION
system*
2 Trander weight Ioadand
clean valve
I. Ftl to recommendedlevei
2 Purge air from hydraulic
system.*
l Purge airfrom hyd_aulic
system"
2 Changeoi_ UseSAE 5W
f, Decreaseweight or change
toa highercapacity iacL
2. FH_to recommendedlevel
For purging air, see Purging Air Instructions on page 3,
10
Page is loading ...
Page is loading ...
Manual del usuario
iCH' MnWI
Modelo No.
875,50190
1 I
PRECAUC:I6N: Lea, comprenda y siga todas
tasnormas de segur}dad y ias instruoeionesde
funcionamiento de es_emanual antes de ut#iza_
este producto
• _uridae
• Garantla
Caraotertst:tcas y
funcionamlento
" Mantenimiento
Scats, Roebuck and Co,, Hoffman Estates, IL 60179 U_S.A
Vtstte nuestto sttto web Ct_-tsman: www, sears,com/cra_eman
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
iiiiiiii¢
iiiiii"
iiiiii
iiiiii
iiiiii
iiiiii
iiiiii
iiiiii
iiiiii
iiiiii
iiiiii
iiiiii
iiiiii
iiiiii
iiiiii
Your Home
For repair- in your home - of al| majar brand applial_s
iawn and garden equipment or heating and _ting systems_
no matter who made it, no matter who sold tt
For the replacement pa_s a_cessories and
owner's manuals that _u need to doAtoyourself,
For Sears professional insta/atien d home applances
aP_ item8 tke garage door openers arid water heaters_
1_00_-MY'HOME ® _!,_s_3)
Ca/a_t_ime day or nigh_(U,,S,,Aa_d Canada}
_ Sea_S eem _a_
iiiiiii .......................... iiiiii
i a _y_a_r_: I_.FOYER _ i
iiiiii 1_s R_ _ ...........
/
