Air King AK280LS Operating instructions

Brand: Air King

Model: AK280LS

Type: Operating instructions

Air King AK280LS is a powerful exhaust fan designed to improve ventilation and remove unwanted odors, moisture, and fumes from various indoor spaces. It features a durable construction, easy installation, and a range of capabilities to meet your ventilation needs:

Efficient Airflow: The AK280LS effectively moves air, helping to circulate fresh air and remove stale air, smoke, and cooking odors from kitchens, bathrooms, workshops, and other areas.
Adjustable Speed Control: Equipped with adjustable speed settings, you can customize the airflow to suit your specific needs, ensuring optimal ventilation while minimizing noise.

Efficient Airflow: The AK280LS effectively moves air, helping to circulate fresh air and remove stale air, smoke, and cooking odors from kitchens, bathrooms, workshops, and other areas.
Adjustable Speed Control: Equipped with adjustable speed settings, you can customize the airflow to suit your specific needs, ensuring optimal ventilation while minimizing noise.

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions

should always be followed to reduce the risk of ﬁre,

electric shock and injury to person, including the following:

SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND INJURY TO PERSON, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer.If

you have questions, contact the manufacturer.

b) Before servicing or cleaning the unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

AND INJURY TO PERSON, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualiﬁed

person(s) in accordance with all applicable codes and standards,

including ﬁre-related construction.

b) Sufﬁcient air is needed for proper combustion and exhausting

of gases through the ﬂue (chimney) of fuel burning equipment

to prevent back drafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA) and the

American Society for Heating, Refrigeration, and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

c) When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be marked

as appropriate for the application and be connected to a GFCI

(Ground Fault Circuit Interrupter) - protected branch circuit.

f) This unit must be grounded.

g) To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power unit.

CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT

USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND

VAPORS.

WARNING: DO NOT USE IN KITCHENS.

h) Read all instructions before installing or using exhaust fan.

www.airkinglimited.com

A210572051 Rev. B 1-13 1 of 8

Exhaust Fan

Models: AK200LS, AK300LS

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE

STARTING INSTALLATION.

SECTION 1

Preparing the Exhaust Fan

1. Unpack fan from the carton and conﬁrm that all pieces are present. In addition to the

exhaust fan you should have:

1 - Grill

1 - Damper Assembly (attached)

4 - Mounting Rails

1 - Mounting Flange

1 - Instruction/Safety Sheet

2. Choose the location for your fan. To ensure the best

air and sound performance, it is recommended that

the length of ducting and the number of elbows be

kept to a minimum, and that insulated hard ducting

be used. Larger duct sizes will reduce noise and

airﬂow restrictions. This fan will require at least 10" of

clearance in the ceiling or wall, and will mount through

drywall up to 3/4" thick.

3. Select the most convenient electrical knockout and remove using a straight-blade screw

driver (Figure 1).

SECTION 2

New Construction

1. Install the rails on the housing and position the housing next to the joist. Line up housing

so that it will be ﬂush with the ﬁnished ceiling. Secure the ends of the rails with screws

or nails (not included) to the joists and slide the housing into the ﬁnal position (Figure 2).

SECTION 3

Existing Construction

1. Set housing in position between the joist and trace an outline onto the ceiling material

(Figure 3). Set housing aside and cut opening, being careful not to cut or damage any

electrical or other hidden utilities. Install the rails on the housing and position the housing

in the previously cut hole so that it is ﬂush with the ﬁnished ceiling. Secure the ends of

the rails to the joists (Figure 3).

SECTION 4

Ducting

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL BUILDING

CODES.

1. Connect the ducting to the fan’s duct collar (Figure 4). Secure in place using tape or

screw clamp. Always duct the fan to the outside through a wall or roof cap.

www.airkinglimited.com

A210572051 Rev. B 1-13 2 of 8

SECTION 5

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE

STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE IN ACCORDANCE

WITH LOCAL CODES, ORDINANCES, OR NATIONAL ELECTRICAL CODE. IF YOU ARE

UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL WIRING, SECURE THE

SERVICES OF A QUALIFIED ELECTRICIAN.

NOTE: This unit includes a side access panel for wiring that does not require the removal of the

fan’s blower assembly. If you choose to wire the unit from the inside, you will need to remove

the blower assembly and internal wiring compartment. Both methods are equally effective.

1a. External Wire Compartment: Remove the wire compartment cover screw and place

cover in a secure place (Figure 5).

1b. Internal Wire Compartment: Using a 7/16" socket, remove the two hex nuts holding the

blower assembly in place. Lift up on the assembly and slide it out of the tabs on the housing

(Figure 6). Remove the wire compartment cover screw and place the cover in a secure

place (Figure 7).

NOTE: If the fan motor plug is connected to the fan housing receptacle, unplug so the blower

assembly can be completely removed.

Figure 1

Ducting

Duct

Collar

Figure 4

Figure 5

Screw

Wire

Compartment

Cover

Figure 7

Screw

Wire Compartment

Cover

Housing

Joist

Mounting Rails

Figure 2

Figure 3

Joist

Plug

Tabs

Hex Nuts

Figure 6

2. Run wiring from an approved wall switch (not included) carrying the appropriate

rating. One neutral (white), one ground (green or bare copper), and one hot (black lead

connected to the switch). Secure the electrical wires to the housing with an approved

electrical connector. Make sure you leave enough wiring in the box to make the

connection to the fan’s receptacle.

3. From where you have chosen to access the fan’s junction box, connect the white wire

from the house to the white wire from the fan’s receptacle. Connect the black wire

from the wall switch to the black wire from the fan’s receptacle. Connect the ground

wire from the house to the green wire from the fan housing (Figure 8). Use approved

methods for all connections.

NOTE: The fan’s receptacle wires might need to be pulled outside the compartment for connection.

Only pull the three loose wires outside of compartment. Additional wires will be present.

NOTE: Unit must be grounded according to all local and national codes.

3. Carefully tuck wire back inside wire compartment and replace wire compartment cover

securing with the screw that was removed earlier.

SECTION 6

Completing the Installation

1. If the fan’s blower assembly was removed during the wiring process, reinstall the

blower by reversing the directions in Section 5 (Wiring), Step 1b.

2. Plug the fan’s quick connect motor cord into the receptacle. This cord will only ﬁt one

way into the receptacle (Figure 9).

www.airkinglimited.com

A210572051 Rev. B 1-13 3 of 8

3. Install the ceiling mounting ﬂange to cover any gaps which exist between the housing and

the ﬁnished ceiling. Line up the slots in the ceiling mounting ﬂange with the screws on the

inside of the housing and press ﬂange in place so it is tight against the ceiling. Tighten both

screws inside the housing. Install drywall screws (not included) through the holes in the

ﬂange and into the ceiling. Install as many drywall screws needed to ensure the ﬂange ﬁts

tightly against the ceiling (Figure 10).

4. Install the grill by squeezing the two ends of the springs together and installing them up

into the slots on the fan’s housing. Push the grill up into position (Figure 11).

5. Restore power and test your installation.

SECTION 7

Use and Care

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE

SERVICING THE UNIT.

1. Cleaning the Grill: Remove grill and use a mild detergent, such as dishwashing liquid,

and dry with a soft cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING POWDERS.

Completely dry grill before reinstalling. Refer to instructions in Section 5 Finishing the

Installation, to reinstall grill.

2. Cleaning the Fan Assembly: Wipe all parts with a dry cloth or gently vacuum the fan.

NEVER IMMERSE ELECTRICAL PARTS IN WATER.

Figure 8

Supply from

house

Ground

White

Hot (Black)

Figure 9

Figure 11

Troubleshooting Guide

Trouble Probable Cause Suggested Remedy

1. Fan does not operate when the switch is on. 1a. A fuse may be blown or a circuit tripped. 1a. Replace fuse or reset circuit breaker.

1b. Connector plug from motor is not plugged in. 1b. Turn off power to unit. Remove Grill and plug motor into receptacle

in housing. Restore power to unit.

1c. Wiring is not connected properly. 1c. Turn off power to unit. Check that all wires are connected.

1d Motor has stopped operating. 1d. Replace motor.

2. Fan is operating, but air moves slower than normal. 2. Obstruction in the exhaust ducting. 2. Check for any obstructions in the ducting. The most common are bird

nests in the roof cap or wall cap where the fan exhausts to the outside.

3. Fan is operating louder than normal 3a. Motor is loose. 3a. Turn off power to unit. Remove grill and check that all screws are fully

tightened. Restore power to unit.

3b. Fan blade is hitting housing of unit. 3b. Call your dealer for service.

Figure 10

Drywall Screw

Screws

Ceiling

Mounting

Flange

Slots

www.airkinglimited.com

A210572051 Rev. B 1-13 4 of 8

LIMITED WARRANTY

WHAT THIS WARRANTY COVERS: This product is warranted against defects in workmanship and/or materials.

HOW LONG THIS WARRANTY LASTS: This warranty extends only to the original purchaser of the product and lasts for ﬁve (5) years from the date of original purchase

or until the original purchaser of the product sells or transfers the product, whichever ﬁrst occurs.

WHAT AIR KING WILL DO: During the warranty period, Air King will, at its sole option, repair or replace any part or parts that prove to be defective or replace the whole

product with the same or comparable model.

WHAT THIS WARRANTY DOES NOT COVER: This warranty does not apply if the product was damaged or failed because of accident, improper handling or operation,

shipping damage, abuse, misuse, unauthorized repairs made or attempted. This warranty does not cover shipping costs for the return of products to Air King for repair or

replacement. Air King will pay return shipping charges from Air King following warranty repairs or replacement

ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY), LAST ONE YEAR

FROM THE DATE OF ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR TRANSFERS THE PRODUCT, WHICHEVER FIRST

OCCURS AND IN NO EVENT SHALL AIR KING’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY INCLUDE (I) INCIDENTAL OR CONSEQUENTIAL DAMAGES

FROM ANY CAUSE WHATSOEVER, OR (II) REPLACMENT OR REPAIR OF ANY HOUSE FUSES, CIRCUIT BREAKERS OR RECEPTACLES. NOTWITHSTANDING ANYTHING TO

THE CONTRARY, IN NO EVENT SHALL AIR KING’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT

AND ANY SUCH LIABILITY SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD.

Some states and provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these

exclusions or limitations may not apply to you. This warranty gives you speciﬁc legal rights. You may also have other rights which vary from state to state and province to

province. Proof of purchase is required before a warranty claim will be accepted.

CUSTOMER SERVICE:

Toll-Free (800) 465-7300

Our Customer Service team is available to assist you with product questions, service center locations, and replacement parts. They can be reached Monday through

Friday, 8am-4pm Eastern. Please have your model number available, as well as the type and style (located on the label inside of your product).

Please do not return product to place of purchase.

www.airkinglimited.com

PARTS FOR DISCONTINUED, OBSOLETE AND CERTAIN OTHER PRODUCTS MAY NOT BE AVAILABLE. DUE TO SAFETY REASONS, MANY ELECTRONIC COMPONENTS

AND MOST HEATER COMPONENTS ARE NOT AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT.

# Qty. Description Replacement Part #

1 4 Mounting Rails 5S1299002

2 1 Blower Assembly - AK200LS 5S2202201

1 Blower Assembly - AK300LS 5S2202301

3 1 6” Metal Collar Assembly 5S5299100

4 2 Grill Springs 5S1202046

5 1 Grill 5S1202048

6 1 Ceiling Flange 5S1202050

7 1 Wire Compartment Assembly - AK200LS 5S1202615

1 Wire Compartment Assembly - AK300LS 5S1202052

8 1 Outlet Gasket 5S1202053

Installer: Installation Date:

Place of Purchase: Model Number:

Page is loading ...

Air King AK280LS Operating instructions

Brand: Air King

Model: AK280LS

Type: Operating instructions

Efficient Airflow: The AK280LS effectively moves air, helping to circulate fresh air and remove stale air, smoke, and cooking odors from kitchens, bathrooms, workshops, and other areas.
Adjustable Speed Control: Equipped with adjustable speed settings, you can customize the airflow to suit your specific needs, ensuring optimal ventilation while minimizing noise.

Download PDF

report