Apple 073-0708 User manual

Brand: Apple

Model: 073-0708

Type: User manual

This manual is also suitable for

Power Mac 073-0708

Apple Power Mac 073-0708: This high-performance computer is designed for demanding tasks such as video editing, music production, and graphic design. With its powerful processor, ample memory, and fast storage, the Apple Power Mac 073-0708 can handle complex applications and large files with ease. It also features a variety of ports and expansion options, allowing you to connect multiple peripherals and upgrade your system as needed. Whether you're a creative professional or a power user, the Apple Power Mac 073-0708 is a capable machine that can meet your computing needs.

073-0708 Rev. A



Power Mac G4

ATA Cable

Replacement Instructions

Follow the instructions in this sheet carefully. Failure to follow these instructions could

damage your equipment and void its warranty.

Note:

Written and video instructions covering customer-installable parts are available at

http://www.info.apple.com/installparts/.

Warning: During this procedure, keep small parts away from children.

Tools Required

The only tool required for this procedure is a Phillips screwdriver.

Opening the Computer

Warning: Always shut down your computer before opening it to avoid damaging its

internal components or causing injury. After you shut down the computer, the

internal components can be very hot. Let the computer cool down before

continuing.

1. Place your computer on a clean, ﬂat surface.

2. If you think your computer is in sleep, press the power button on the front of the

computer to wake it.

3. Shut down your computer and wait ﬁve minutes before continuing.

4. If you attached a security cable through the computer’s lockable cover latch, remove

the cable.

5. Unplug all other cables from the computer except the power cord.

Power Mac G4 (Mirrored Drive Doors/FW 800) ATA Cable -

6. Touch the metal PCI access covers on the back of the computer.

(Figure 1)

Figure 1

Important:

To avoid electrostatic discharge, always ground yourself by touching the

port access covers before you touch any parts or install any components inside the

computer. To avoid static electricity building back up in your body, do not walk

around the room until you have completed the installation and closed the computer.

7. Unplug the power cord.

Warning: The power supply in your computer is a high-voltage component and

should not be opened for any reason, even when the computer is off. If the

power supply needs service, contact your Apple reseller or Apple Authorized

Service Provider.

8. Lift the latch on the right side access panel.

9. Gently lower the access panel until it lies ﬂat. To avoid scratching the case, lower the

panel onto a soft, clean cloth.

Warning: If you see any lights glowing on the main logic board, the computer has

not been shut down. Close the side access panel and shut down the computer

before proceeding.

Power Mac G4 (Mirrored Drive Doors/FW 800) ATA Cable -

Removing the ATA Cable

1. Disconnect the ATA 100 cable from the logic board.

(Figure 2)

Figure 2

Power Mac G4 (Mirrored Drive Doors/FW 800) ATA Cable -

Note:

To reach the ATA cable connector on the back hard drive, you may need to

remove the carrier. If so, use a Phillips screwdriver to remove the mounting screw that

holds the carrier to the chassis. Then pull the carrier lever forward and slide up the

carrier to disconnect it from the chassis.

(Figure 3)

Figure 3

Power Mac G4 (Mirrored Drive Doors/FW 800) ATA Cable -

3. Rotate the carrier back from the chassis far enough to reach the drive cables.

Disconnect the ATA ribbon cable from the hard drive(s).

(Figure 4)

4. Open the cable clamp at the bottom of the chassis to free the ATA cable.

Figure 4

Power Mac G4 (Mirrored Drive Doors/FW 800) ATA Cable -

Installing the Replacement ATA Cable

1. Connect the ATA cable to all drives.

2. Reinstall the hard drive carrier, if necessary.

Note:

Be sure to align the mounting pegs on the back of the carrier with the notches

in the chassis. Then press the carrier in and down until the pegs engage and the left

side lever clicks into place.

(Figure 5)

Figure 5

Power Mac G4 (Mirrored Drive Doors/FW 800) ATA Cable -

3. Secure the ATA cable with the cable clamp.

4. Connect the cable to the logic board.

Closing the Computer

1. Raise the side access panel, lift the latch, and press the panel against the case until it

snaps securely into place.

2. Reconnect all cables and restart your computer.

Warning: Never turn on your computer unless all of its internal and external

parts are in place and it is closed. Operating the computer when it is open or

missing parts can damage your computer or cause injury.



Apple Computer, Inc.

Under the copyright laws, this document may not be copied, in whole or in part, without the

written consent of Apple.

The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other

countries. Use of the “keyboard” Apple logo (Option-Shift-K) for commercial purposes

without the prior written consent of Apple may constitute trademark infringement and

unfair competition in violation of federal and state laws.

Every effort has been made to ensure that the information in this document is accurate.

Apple is not responsible for printing or clerical errors.

Apple Computer, Inc.

1 Inﬁnite Loop

Cupertino, CA 95014-2084

USA

+ 1 408 996 1010

http://www.apple.com

Apple, the Apple logo, Mac, Macintosh, and the Mac logo are trademarks of Apple

Computer, Inc., registered in the U.S. and other countries.

Power Mac is a trademark of Apple Computer, Inc.

Apple 073-0708 User manual

Brand: Apple

Model: 073-0708

Type: User manual

This manual is also suitable for

Power Mac 073-0708

Download PDF

report

Apple 073-0708 User manual

This manual is also suitable for

Apple 073-0708 User manual

Related papers

Other documents