BrassCraft G2CR14X C1 Installation guide

Brand
BrassCraft
Model
G2CR14X C1
Category
Sanitary ware
Type
Installation guide
PIPE NIPPLE
Tubo roscado
VALVE / Llave de paso
THREAD SEALANT / Selladora de rosca
COPPER TUBE / Tubo de cobre
COMPRESSION NUT / Tuerca de compresión
SLEEVE / Manga
VALVE / Llave de paso
PEX TUBE
Tubo de PEX
TUBE INSERT (IF NEEDED) / Inserto para tubería
COMPRESSION NUT / Tuerca de compresión
SLEEVE / Manga
VALVE / Llave de paso
ESCUTCHEN
Chapetón
FLUX
Pasta
fundente
BRASS WASHER
Rondana de latón
STEM ASSEMBLY / Cartucho
SOLDER
Soldadura
BONNET NUT
Tuerca de capuchón
SOLDER
Soldadura
STUB OUT
Caño de alimentación
RUBBER BIBB WASHER
Arandela de goma
tipo babero
VALVE SOCKET
Entrada de la llave de paso
CPVC PIPE
Tubo de CPVC
Water Supply Stops
INSTALLATION INSTRUCTIONS
Read All Instructions Carefully Before Beginning Installation.
CAUTION: FOR USE WITH WATER IN ACCESSIBLE LOCATIONS ONLY.
CAUTION:
DO NOT SWEAT WITHIN 12 INCHES OF A G2 1/4 TURN VALVE.
CAUTION: FRACTURES CAN DEVELOP OVER TIME IF USED WITH CONNECTORS
USING A SOLID BRASS CONE DESIGN
Manufacturer assumes no responsibility for failure due to improper installation.
GENERAL INSTRUCTIONS:
• Besurestuboutandriseraresquare,roundandfreeofburrs.
• Overtighteningcancauseproducttocrackandfailovertime.Seemoredetailed
instructions below:
COPPER COMPRESSION INLET
Be sure to shut off water before starting.
ForusewithtypeLorMcopperonly.
1. Placecompressionnutandsleeve
 ontothecoppertube.
2. Adropofgeneralpurposeoilwill
 maketighteningeasier.
3. Ifusingadropofoilorthread
 sealantbesurethethreadsareclean
 ofanydebrisandthatsealantisalso
 freeofanymetaldebris.DONOTUSEaputty,gasketmaterialorthreadsealtape.
4. Ifusingathreadsealant,applyathinevencoattothemalecompressionthreads
 onlytakingcarenottogetthreadsealantonthecompressionringorsealing
 surface.Warning:Excessivethreadsealantmaycausejointtofail.
5. Handtightenthecompressionnutontothestopasfarasitwillallow.
6. Usinghandtools,tighten3/4turnfromthehandtightposition.Note:Makesurethat
 thestopremainsseatedandsquaretothecoppertube.Ifthestopisnotsquareto
 thecoppertube,thiscouldaffecttheabilitytogetagoodconnection.
7. Forrisertubeinstallation,seethatsection.
Tools Needed for Installation: • Wrench • Tube Cutter
PEX COMPRESSION INLET
Be sure to shut off water before starting.
ForuseASTMF876/F877PEXonly.
Note:On3/8”ODandsmaller,useplasticcompressionsleeve.Onlargerthan3/8”OD,
usebrasscompressionsleevew/stainlesssteeltubeinsert.
1. Placecompressionnutandsleeve
 ontothePEXtube.
2. Iflargerthan3/8”OD,insert
 stainlesssteeltubeinsert.
3. Adropofgeneralpurposeoilwill
 maketighteningeasier.
4. Ifusingadropofoilorthreadsealant
 besurethethreadsarecleanofany
 debrisandthatsealantisalsofree
 ofanymetaldebris.
 DONOTUSEaputty,gasketmaterial
 orthreadsealtape.
5. Ifusingathreadsealant,applyathinevencoattothemalecompressionthreads
 onlytakingcarenottogetthreadsealantonthecompressionringorsealing
 surface.Warning:Excessivethreadsealantmaycausejointtofail.
6. Handtightenthecompressionnutontothestopasfarasitwillallow.
7. Usinghandtools,tighten3/4turnfromthehandtightposition.Note:Makesurethat
 thestopremainsseatedandsquaretothePEXtube.Ifthestopisnotsquareto
 thePEXtube,thiscouldaffecttheabilitytogetagoodconnection.
8. Forrisertubeinstallation,seethatsection.
Tools Needed for Installation: • Wrench • Tube Cutter
FEMALE IRON PIPE (FIP INLET)
Be sure to shut off water before starting.
1. Applythreadsealanttopipenipple.
 Threadvalveontopipe.Wrenchtighten.
Makesureoutletispositionedcorrectly.
Tools Needed for Installation:
• Threadsealant•Wrench
SWEAT INLET
Be sure to shut off water before starting.
NOTE:
Removecompletestemassemblybylooseningbonnetnutandunthreading
handletopreventheatdamagetowashers.Reassembleafterinstallationiscomplete.
1. Cleanoutsideofcopperstuboutandinsideoftting/valvewithemerycloth
 orsteelwoolandremovealllooseparticles.
2. Coatoutsideofcopperstuboutandinsideoftting/valvewithux.
 Pushtting/valveoverstuboutandrotatetodistributeuxevenly.
3. Applyheattoallsides,checkingtemperatureoccasionallybytouchingend
 ofsoldertosurface(nottoame).Whensolderliquees,temperatureiscorrect.
 Feedsolderaroundedgeoftting/valveasheatisapplied.
4. Whilestuboutisstillhot,carefullywipevalvewithdampragtoleavean
 attractivechrome-likenish.Avoidmovingtting/valveuntilsolderhardens.
Tools Needed for Installation:•Emeryclothorsteelwool•Flux•Solder•Wrench•Damprag
CPVC INLET
Be sure to shut off water before starting.
CAUTION: USE ONLY CPVC CEMENT OR
AN ALL-PURPOSE CEMENT CONFORMING TO
ASTM F-493 OR JOINT FAILURE MAY RESULT.
CAUTION: ASSEMBLE VALVE ACCORDING
TO SOLVENT WELD MANUFACTURER’S
INSTRUCTIONS.
1. Cutpipesquarelyandremoveallinside
 andoutsideburrs.
2. Followsolventweldmanufacturer’s
 instructions.
CAUTION: TOO MUCH CEMENT CAN CLOG WATERWAYS AND WEAKEN INSERT
IN FITTING OR VALVE.
Tools Needed for Installation:
• CPVCCleaner/Primer(ornesandpaper)
•CPVCCement• Wrench
CRIMP RING
Anillo de presión
BARBED INLET
Entrada tipo espiga
PEX TUBE
Tubo de PEX
VALVE
Llave de paso
EXPANSION RING
Anillodeexpansión
BARBED INLET
Entrada tipo espiga
PEX TUBE
Tubo de PEX
VALVE
Llave de paso
DEPTH MARKING
Mcradeprofundidad
TUBE INSERT
Inserto para tubería
LOCKING CLIP / Clip de retención
TUBE
Tubo
REMOVAL
FLANGE
Campana para remover
TO CUT COPPER
Al cobre cortado
TO CUT PEX & CPVC
Al PEX o CPVC cortado
SLIP-JOINTNUT
Tuercadejunta
deslizable
FRICTION RING
Anillodefricción
VALVE OUTLET
Salida de la llave
de paso
CONE
WASHER
Rondana
cónica
VALVE
Llave de paso
BRASS
SLEEVE
Manga de latón
COPPER
TUBE
Tubo de
cobre
COMPRESSION NUT
Tuerca de
compresión
VALVE OUTLET
Salida de la llave
de paso
VALVE
Llave de paso
G2PC
G2PS
DepthMarking
Tube Insert
BARBED PEX INLET
Be sure to shut off water before starting.
ForusewithASTMF876/F877/F1807PEXonly
CAUTION: ASSEMBLE STOP
ACCORDING TO CRIMP TOOL
MANUFACTURER’S INSTRUCTIONS.
1. CutPEXtubesotheendis
 squareandround.
2. SlidecrimpringoverPEXtube.
3. InsertvalvebarbinletintoPEXtube
 completelyuntiltubestopsat
 valvebody.
4. Positioncrimpringoverbarbarea
 andfollowcrimptoolmanufacturer’s
 instructionstosecure.
Tools Needed for Installation:• TubeCutter•CrimpTool•PEXCrimpGauge
COLD EXPANSION PEX ON INLET
Be sure to shut off water before starting.
ForuseASTMF876/F877/F1960PEXonly.
CAUTION: ASSEMBLE STOP
ACCORDING TO PEX COLD EXPANSION
TOOL MANUFACTURER’S
INSTRUCTIONS.
1. CutPEXtubesothattheendis
 squareandround.
2. SlidethePEXreinforcementring
 overthePEXtube.
3. FollowthePEXcoldexpansiontool
 manufacturer’sinstructionsfor
 installationofthestopbarbinlet.
4. Forrisertubeinstallation,seethatsection.
Tools Needed for Installation: •TubeCutter•ExpansionTool
PUSH CONNECT INLET
• ForusewithCopper,PEXandCPVC
• Forusewithwaterinexposedlocationsonly.
Be sure to shut off water before starting.
INSTALLATION
1. CutCopper,PEXorCPVCtubesquare,round
andfreeofburrs.Ifsharpedgesarenot
removed,connectionmayleak.Makesure
stub-outlengthwillaccommodatedepthof
stopandange.
2.
Marktube:ifG2PC,thanmark1-1/8”fromend.
IfG2PS,thenmark1”fromend.Pushvalve
ontotubeasfaraspossible,atleasttoline
markingontubeisreached.Tubeinsertwill
selfalignintubing.
REMOVAL
1. Withwaterpressureoffandsystem
depressurized,besuretoremovesupplyline
anddrainanyremainingwaterfromtube.
2. Removelockingclip.
3. Positionstoprmlyinpalmasshown.
Withtwongers,depress
removalangeback
towardsstopandpullfromtubing.
4. Beforere-installing
stop,insertlockingclip
betweenremovalangeandstopbody.
CAUTION:
• FAILURE TO PUSH VALVE TO MARK MAY
RESULT IN A LEAK.
• DO NOT USE ANY PLUMBER’S PUTTY,
PIPE THREAD TAPE, OR OTHER SEALANT TO
CONNECT VALVE.
• IF G2 1/4 TURN VALVE INSTALLATION, DO NOT
SWEAT WITHIN 12 INCHES OF THE VALVE.
• ONLY INSERT COPPER, PEX OR CPVC TUBING
INTO THE VALVE.
• DO NOT ATTEMPT TO REMOVE TUBE SUPPORT.
SLIP-JOINT OUTLET
Be sure to shut off water before starting.
NOTE: Do not use pipe compound on
 slip-jointthreads.
1. Besuretubeisnotattened
out-of-roundandallburrsare
removed.Iftubeisovalor
out-of-round,donotrelyonthenut
tocorrect.Bringintoshapebefore
tighteningnut.Replacetubeifit
isgrooved,pockedorscarred
asabrasionspreventagoodseal.
2. Slideslip-jointnut,frictionringand
conewasherontotube.
3. Besuretubeislinedupwithvalve
soitentersstraightand“bottoms”
true.Ifcockedortilted,nutwillnot
seatproperlyandcouldeventually
developaleak.
4. Tightennut,wrenchtighten.DONOTOVERTIGHTEN.Usetapetoprotectthenish.
5. Turnonmainwatersupply.Turnonvalvecounterclockwise.Ifslip-jointnutleaks,
turnoffwatersupply.Backoff(loosen)nutcompletely,realignandretighten.
DONOTOVERTIGHTENasthiscouldleadtofuturefailure.
Tools Needed for Installation:•Wrench•Protectivetape
•Sandpaperorle(ifnecessary)
COPPER COMPRESSION OUTLET
Be sure to shut off water before starting.
1. Cuttherisertubetolengthsoitbottomsoutinthestop.
2. Placecompressionnutandsleeve
 ontothecoppertube.
3. Adropofgeneralpurposeoilwill
 maketighteningeasier.
4. Ifusingadropofoilorthreadsealant
 besurethethreadsarecleanofany
 debrisandthatsealantisalsofreeof
 anymetaldebris.DONOTUSEaputty,
 gasketmaterialorthreadsealtape.
5. Ifusingathreadsealant,applyathin
 evencoattothemalecompression
 threadsonlytakingcarenottoget
 threadsealantonthecompression
 ringorsealingsurface.
 Warning:Excessivethreadsealant
 maycausejointtofail.
6. Handtightenthecompressionnutontothestopasfarasitwillallow.
7. Usinghandtools,tighten1to1-1/4turnsfromthehandtightposition.Note:Make
 surethattheriserremainsseatedandsquaretothestop.Iftheriserisnotsquare
 tothestop,thiscouldaffecttheabilitytogetagoodconnection.
8. Forinlettubeinstallation,seethatsection.
Tools Needed for Installation:•Wrench•TubeCutter
FLEXIBLE
RISER
Conectorexible
COMPRESSION NUT
Tuerca de compresión
VALVE OUTLET
Salida de la llave
de paso
VALVE
Llave de paso
COMPRESSION
SLEEVE
Manga de
compresión
PEX TUBE
Tubo de PEX
TUBE INSERT
(IF NEEDED)
Inserto para tubería
COMPRESSION
NUT
Tuerca de
compresión
VALVE OUTLET
Salida de la llave
de paso
VALVE
Llave de paso
PEX COMPRESSION OUTLET
Be sure to shut off water before starting.
Note:
On3/8”ODandsmaller,useplasticcompressionsleeve.Onlargerthan
3/8”OD,usebrasscompressionsleevew/stainlesssteeltubeinsert.
1. Cuttherisertubetolengthsoit
bottomsoutinthestop.
2. Placecompressionnutand
sleeveontothePEXtube.
3. Iflargerthan3/8”OD,insert
stainlesssteeltubeinsert.
4. Adropofgeneralpurposeoilwill
maketighteningeasier.
5. Ifusingadropofoilorthread
sealantbesurethethreadsare
cleanofanydebrisandthat
sealantisalsofreeofanymetal
debris.DONOTUSEaputty,
gasketmaterialorthread
sealtape.
6. Ifusingathreadsealant,applyathinevencoattothemalecompressionthreads
onlytakingcarenottogetthreadsealantonthecompressionringorsealing
surface.Warning:Excessivethreadsealantmaycausejointtofail.
7. Handtightenthecompressionnutontothestopasfarasitwillallow.
8. Usinghandtools,tighten1-1/2to2turnsfromthehandtightposition.Note:Make
surethattheriserremainsseatedandsquaretothestop.Iftheriserisnotsquare
tothestop,thiscouldaffecttheabilitytogetagoodconnection.
9. Forinlettubeinstallation,seethatsection.
Tools Needed for Installation:•Wrench•TubeCutter
FLEXIBLE NUT X NUT RISER
Be sure to shut off water before
starting.
1. Followexiblerisermanufacturer’s
instructions.
BrassCraftMfg.,39600OrchardHillPlaceNovi,Michigan48375-5331
TOLL-FREE:877.272.7755FAX:248.305.6011www.brasscraft.com
©2009-2015BrassCraftMfg.
425.04Rev.6/15
Scanfor
more
information
Escanear
paramayor
información
Manufacturerassumesnoresponsibilityforfailureduetoimproperinstallation.
©2015BrassCraftMfg.,Novi,MI48375-5331U.S.A.AllRightsReserved.www.brasscraft.com
Designed,MachinedandAssembledintheU.S.A.
Elfabricantenoasumeningunaresponsabilidadsilainstalaciónnosehacedeacuerdoalinstructivo.
TodoslosDerechosReservados.Diseñado,MaquinadoyEnsambladoenE.U.A.
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

BrassCraft G2CR14X C1 Installation guide

Brand
BrassCraft
Model
G2CR14X C1
Category
Sanitary ware
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents