Jensen JSBW-210 User manual

Brand: Jensen

Model: JSBW-210

Category: Bluetooth music receivers

Type: User manual

WALL MOUNTABLE 2.0-CHANNEL BLUETOOTH SOUNDBAR

Model: JSBW-210

USER MANUAL

PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND

RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

IMPORTANT SAFETY INSTRUCTIONS

When used in the directed manner, this unit has been designed and manufactured to

ensure your personal safety. However, improper use can result in potential electrical

shock or fire hazards. Please read all safety and operating instructions carefully before

installation and use, and keep these instructions handy for future reference. Take

special note of all warnings listed in these instructions and on the unit.

1. Read these instructions – All the safety and operating instructions should be read

before the appliance is operated.

2. Keep these instructions – The safety and operating instructions should be kept for

future reference.

3. Heed all warnings – All warnings on the appliance and in the operating instructions

should be adhered to.

4. Follow all instructions – All operation and use instructions should be followed.

5. Do not use this apparatus near water – The appliance should not be used near

water; for example, near a bath tub, washbowl, kitchen sink, laundry tub, in a wet

basement, or near a swimming pool.

6. Clean only with dry cloth – The appliance should be cleaned only as

recommended by the manufacturer.

7. Do not blo

ck any ventilation openings. Install in accordance with the

manufacturer’s instructions. The appliance should be situated so that its location or

position does not interfere with its proper ventilation. For example, the appliance

should not be situated on a bed, sofa, rug, or similar surface that may block the

ventilation openings; or placed in a built-in installation, such as a bookcase or

cabinet that may impede the flow of air through the ventilation openings.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

9. AC adaptor is used as disconnect device and it should remain readily operable

during intended use. In order to disconnect the apparatus from the mains

completely, the AC adaptor should be disconnected form the mains socket outlet

completely.

10. Only use attachments / accessories specified by the manufacturer.

11. Use only with a cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury

from tip-over.

12. Unplug this apparatus during lightning storms or when unused for long periods of

time.

13. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

14. This appliance shall not be exposed to dripping or splashing water and that no

object filled with liquids such as vases shall be placed on the apparatus.

15. Power Sources – The appliance should be connected to a power supply only of the

type described in the operating instructions or as marked on the appliance. Do not

overload wall outlet.

16. Battery shall not be exposed to excessive heat such as sunshine, fire or the like

17. Danger of explosion if battery is incorrectly replaced. Replace only with the same

or equivalent type.

18. Do not attempt to dismantle, open or repair this product yourself. If a fault occurs,

seek advice from your local qualified service technician or contact the distributor

via the telephone number at the back of this instruction manual.

19. Caution marking and nameplate are located on bottom of product.

IMPORTANT NOTE

Avoid installing the unit in locations described below:

Places exposed to direct sunlight or close to heat radiating appliances such as

electric heaters.

Places subject to constant vibration.

Dusty, humid or moist places.

Sources of electrical noise such as fluorescent lamps or motors.

In case of malfunction due to electrostatic discharge, the apparatus has to be reset

by disconnecting it from mains supply, wait at least for 60 seconds before reconnect

the AC power cord.

COMPLIANCE WITH FCC REGULATIONS

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate

the equipment.

Protect Your Furniture

This product is equipped with non-skid rubber 'feet' to prevent the product from moving

when you operate the controls. These 'feet' are made from non-migrating rubber

material specially formulated to avoid leaving any marks or stains on your furniture.

However certain types of oil based furniture polishes, wood preservatives, or cleaning

sprays may cause the rubber 'feet' to soften, and leave marks or a rubber residue on

the furniture. To prevent any damage to your furniture we strongly recommend that you

purchase small self-adhesive felt pads, available at hardware stores and home

improvement centers everywhere, and apply these pads to the bottom of the rubber

'feet' before you place the product on fine wooden furniture.

DEAR JENSEN® CUSTOMER

Selecting fine audio equipment such as the unit you've just purchased is only the

start of your musical enjoyment. Now it's time to consider how you can maximize the

fun and excitement your equipment offers. This manufacturer and the Electronic

Industries Association's Consumer Electronics Group want you to get the most out of

your equipment by playing it at a safe level. One that lets the sound come through

loud and clear without annoying blaring or distortion and, most importantly, without

affecting your sensitive hearing.

Sound can be deceiving. Over time your hearing "comfort level" adapts to higher

volumes of sound. So what sounds "normal" can actually be loud and harmful to your

hearing. Guard against this by setting your equipment at a safe level BEFORE your

hearing adapts.

To establish a safe level:

Start your volume control at a low setting.

Slowly increase the sound until you can hear it comfortably and clearly, and

without distortion.

Once you have established a comfortable sound level:

Set the dial and leave it there.

Taking a mi

nute to do this now will help to prevent hearing damage or loss in the

future. After all, we want you listening for a lifetime.

We Want You Listening For a Lifetime

Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment.

Since hearing damage from loud noise is often undetectable until it is too late, this

manufacturer and the Electronic Industries Association's Consumer Electronics

Group recommend you avoid prolonged exposure to excessive noise.

Customer's Record:

The serial number of this product is found on its back cover. You should note the

serial number of this unit in the space provided as a permanent record of your

purchase to aid in identification in the event of theft of loss.

Model Number: JSBW-210 Serial Number: ____________________

ACCESSORIES

1 x AC Adaptor

1 x Remote Control,

1 x Stereo Audio Connection Cable with 3.5mm stereo plugs

1 x User Manual

1 x RCA Connection Cable

1 x Wall Mount Template

2 x Wall Spacers

2 x Anchor (For Mounting on Drywall)

2 x 40 mm Pan Head Screws (For Mounting to Wood Studs)

2 x 55 mm Pan Head Screws (For Mounting on Drywall)

INSTALLATIONS

Placing the JSBW-210 on a table

Ventilation

When placing the Sound Bar on an entertainment center, bookshelf, or any type of

enclosed space, be sure to allow at least 2-3 inches of space around the Sound

Bar for ventilation. If the Sound Bar is enclosed in a tight space, without ventilation,

heat generated from the Sound Bar could create potential overheating.

Mounting the JSBW-210 on a wooden wall

It’s important to be sure there are no electric, gas or water lines located behind the wall

where you are attaching the sound bar. We recommend having this speaker

professionally installed. Use the included wall mounting accessories and template to

attach the sound bar to the wall.

Supplied Wall Spacer

Supplied Screw

24.25 (616mm)

(616mm)

24.25

1. Use the supplied wall mounting template to make drill hole marks on the wall. Make

sure the marks are level before drilling.

2. Screw the supplied pan head screws directly into the marks that you made on the

wall as shown above. Make sure the wall is either wood or you are screwing directly

into a wood stud in the wall. The screw head should be left sticking out about 1/10”

(2.54mm) away from the surface of wall.

NOTE:

Install the included wall spacers if you are using the Optical Input, or using

RCA plugs that interfere when mounting the soundbar to the wall.

Attach the Wall Spacers removing the screw from the wall that was installed above in

Step #3. Place the screw through the hole in the spacer and reattach to the wall as

shown below. The screw head should be left sticking out beyond the spacer by

about 1/10” (2.54mm).

3. Place the sound bar onto the mounting screw heads. Make sure the sound bar is

attached firmly to the wall.

Mounting the JSBW-210 on drywall

1. Use the supplied wall mounting template to make drill hole marks on the wall for the

anchors. Make sure the marks are level before drilling.

2. Use a 0.24” (6 mm) bit and power drill (Not supplied) to drill holes on the marks.

3. Insert the included plastic anchors into the holes and push in until they are flush with

the wall.

4. Secure the included pan head screws into the anchors and tighten until the screw

head is 1/10” (2.54mm) away from the surface of spacers.

WALL

Supplied Screw

The incline side of the Wall Spacer

must be facing the soundbar.

The wide side must be located

at the bottom.

Distance between the wall spacer

and the screw 1/10’’ (2.54mm)

Supplied Wall Spacer

supplied Plastic Inserts

Supplied Wall Spacer

supplied Screws

supplied Plastic Inserts

supplied Screws

(616mm)

24.25

(616mm)

24.25

NOTE: Install the included wall spacers if you are using the Optical Input, or using

RCA plugs that interfere when mounting the soundbar to the wall.

Attach the Wall Spacers removing the screw from the wall that was installed above in

Step #3 (Mounting the JSBW-210 on a wooden wall section). Place the screw through

the hole in the spacer and reattach to the wall as shown below. The screw head

should be left sticking out beyond the spacer by about 1/10” (2.54mm).

5. Place the sound bar onto the mounting screw heads. Make sure the sound bar is

attached firmly to the wall.

LOCATION OF CONTROLS

MAIN UNIT

Front View

Back View

Right Hand Side View

1. MODE INDICATOR LED

NSOR

TORS (L/R RCA JACKS)

TANDBY

2. REMOTE INFRARED SE

3. OPTICAL INPUT JACK

AUX 2 INPUT

CONNEC

DC IN JACK

6. POWER ON/S ; MODE BUTTON

CTOR

EMOTE CONTROL

7. VOLUME + BUTTON

AUX 1 INPUT CONNE

9. VOLUME - BUTTON

1. POWER ON/STANDBY BUTTON

2. AUX 1 INPUT SELECTOR BUTTON

3. BLUETOOTH MODE /PAIR BUTTON

/VOICE)

KIP FORWARD  BUTTON

LECTOR BUTTON

/PAUSE

4. SOUND MODE BUTTONS (MUSIC/MOVIE

5. TREBLE +/- BUTTONS

6. SKIP BACKWARD ; S

7. AUX 2 INPUT SELECTOR BUTTON

8. MUTE BUTTON

9. OPTICAL INPUT SE

10. VOLUME UP (+) / DOWN (–) BUTT

ONS

11. BASS +/- BUTTON

12. BLUETOOTH PLAY BUTTON

OPTICAL

AUX 2

MUTE

/PAIR

AUX 1

GETTING STARTED

CONNECTING THE JSBW-210 EVICES

your television or

TO EXTERNAL AUDIO D

You can connect the JSBW-210 audio input to the audio output of

DVD Player. Please see figure below.

OTE:

sure that the power is turned off when connecting or disconnecting the other

ded AC adaptor with 18V

1. Make

devices. Make sure that the other devices are connected to the correct terminals.

2. This unit is not magnetically shielded and may cause color distortion on the screen

of some TVs or video monitors. To avoid this, you may need to move the unit further

away from the TV or monitor if unnatural color shifts or image distortion occurs.

ONNECTING THE AC POWERC

This unit operates using the inclu

1.3A (center-positive

) output, and is compatible with standard 120V~ 60Hz AC household power

the the DC Plug of the AC Adaptor into the DC IN jack on the back of the unit. 1. Insert

Plug the AC Adaptor into a standard 120V~ 60Hz AC wall outlet.

2. Tap the Power /Standby button on remote control or press and hold the

/MODE on main unit to turn on the unit. Mode LED Indicator changes color from

red to relative mode.

3. Tap the Power /Standby button on remote control or press and hold the

/MODE button on the main unit to turn the unit into standby mode after you finish

listening.

REMOTE CONTROL BATTERY INSTALLATION

y (included). To activate

hen the operation of the remote control becomes intermittent or

battery.

The remote control operates on one CR2025 batter

the remote control, remove the insulation tab inserted in the battery

compartment. To remove the tab, pull it in the direction of the arrow in the

illustration as

shown.

unsatisfactory, replace the original battery with a new 3-volt lithium

Replacing the battery in the remote control:

1.) Press in on the side of the battery holder and pull the holder out of the remote.

2.) Removed the exhausted battery and then install 1 new “CR2025” lithium

battery according to the polarity diagram on the battery compartment.

3.) Insert the battery holder into the remote control and make sure it locks into place.

NOTE: Only use a well-known brand of battery to ensure the longest life and best

performance.

Battery Precautions

 Replacement of batteries must be done by an adult.

 The supply terminals are not to be short-circuited.

 Non-rechargeable batteries are not to be recharged.

 Exhausted batteries are to be removed.

 Only batteries of the equivalent type are to be used.

 Batteries are to be inserted with the correct polarity.

 Dispose of batteries properly. Do not dispose of batteries in fire. The batteries

may explode or leak.

WARNING

DO NOT INGEST BATTERY, CHEMICAL BURN

HAZARD

The remote control supplied with this product contains a coin/button cell

battery. If the coin/button cell battery is swallowed, it can cause severe

internal burns in just 2 hours and can lead to death.

Keep new and used batteries away from children. If the battery

compartment does not close s

ecurely, stop using the product and keep it

away from children.

If you think batteries might have been swallowed or placed inside any part

of the body, seek immediate medical attention.

E10

BLUETOOTH OPERATION

PAIRING (LINKING) A BLUETOOTH ENABLED CELL PHONE OR OTHER

BLUETOOTH ENABLED DEVICE to the JSBW-210

1. With the power on, tap the Bluetooth button on remote control or tap the

/MODE button on main unit repeatedly to select Bluetooth mode. The Mode

Indicator LED turns blue and will be flashing. The JSBW-210 is now ready to pair

(link) with your Bluetooth device.

2. Turn on the Bluetooth feature of your cell phone and enable the search or scan

feature to find the JSBW-210.

3. Select "JSBW-210" from the device list when it appears on your device screen. If

required, enter the pass code “0000” to pair (link) the JSBW-210 with your cell

phone.

4. After successfully pairing (linking) your cell phone with the JSBW-210, the Mode

Indicator LED stops flashing and remains lit blue. You can now play music from

your cell phone or Bluetooth device wirelessly to the JSBW-210.

Note: If you want to connect the JSBW-210 to another cell phone after pairing

successfully, then you need to turn off the Bluetooth on the paired cell phone

first if it

is in range before going through the above steps. Otherwise, the

JSBW-210 will automatically reconnect to the previously linked cell phone or

device.

5. Press the VOLUME +/- button to adjust the desired volume level.

NOTE: The Red LED will light and flash to acknowledge the VOLUME+/-,

TREBLE+/- or BASS +/- button is pressed. When the setting reaches its

maximum or minimum level, the red LED will not light for indication.

6. To turn off the JSBW-210 Bluetooth, tap the /STANDBY button on remote

control or press and hold the /MODE button on main unit to turn the unit to

standby mode. Mode Indicator LED turns red. Don’t forget to also turn off the

Bluetooth feature on your cell phone or Bluetooth device.

Notes:

1.) Refer to manual of your cell phone or other Bluetooth enabled device for

Bluetooth operation, since it may vary from model to model.

2.) If your Bluetooth enabled device does not support A2DP, it will not play the music

through the speaker, even after it's paired (linked).

3.) If you are pairing (linking) your computer

to the JSBW-210 using Bluetooth, you

may need to set the JSBW-210 as your computer’s default sound device.

E11

CONTROLLING THE MUSIC PLAYBACK ON YOUR BLUETOOTH DEVICE USING

THE REMOTE CONTROL

1. Tap the /STANDBY button on remote control or press and hold the /MODE on

main unit to turn on the unit.

2. Turn on Bluetooth of your cell phone or device which was previously paired with the

JSBW-210, tap the Bluetooth button on remote control or tap /MODE button

on main unit repeatedly to select the Bluetooth mode, the Mode Indicator LED turns

blue and begins flashing.

3. After the Bluetooth device is paired with the JSBW-210, wait for around 5 seconds

and then press the PLAY/PAUSE button on remote control to start music

playback from your cell phone or Bluetooth device.

4. Press the PLAY/PAUSE button to pause or resume playback.

5. Press the VOLUME+/- button to adjust your desired volume level

6. If necessary, press the MUSIC, MOVIE or VOICE button on remote control to select

different sound effects or press the TREBLE or BASS +/- buttons on t

he remote

control to adjust the separate treble and bass levels.

7. Press the  or  button on the remote to select the desire music track.

8. Tap the /STANDBY button on remote control or press and hold the /MODE

button on main unit to turn off the unit after listening.

Re-linking to a cell phone or Bluetooth device

If your cell phone or Bluetooth device is already paired with the JSBW-210, but became

unlinked at some point, even with both Bluetooth devices turned on. You can re-link

them by:

1. Press and hold the

/PAIR button to re-link your cell phone. The Mode Indicator

LED will turn blue and flash while linking.

2. Select the JSBW-210 from the devices list on your cell phone for linking. The Mode

Indicator LED stops flashing and remains lit blue if the JSBW-210 and your cell

phone have been re-linked successfully.

3. You can also re-link the JSBW-210 by using Bluetooth operation of your cell phone.

Please refer to operation manual of your cell phone for more information.

PRESET SOUND ENHANCEMENTS (REMOTE CONTROL ONLY)

The JSBW-210 features 3 different sound enhancements to customize your listening

experience. You can select the desired effect by pressing the MUSIC, MOVIE or

VOICE button on remote control, red LED will flash once to confirm. The red LED will

not flash if the unit already in relative sound enhancement mode.

In addition, you can adjust treble and bass effects by using the TREBLE & BASS +/-

buttons.

NOTES FOR SOUND MODE BUTTONS:

1.) Press

Buttons.

the MUSIC button first in order to use the separate TREBLE & BASS +/-

E12

2.) When in MOVIE or VOICE sound mode, pressing the MUSIC button will reset the

BASS and TREBLE settings back to center (Normal) positions.

MUTE (Remote Control Only)

- Press the MUTE button on remote control to mute the sound output from speaker

temporarily, the red LED will light and flash.

- Press the button again to resume to normal speaker playback.

LISTENING TO AUDIO FROM A TV/DVD PLAYER/VCR OR DVR

You can connect the JSBW-210 to other external audio devices using the AUX 2 RCA

Input connectors located on the back of the unit.

1. Connect the external TV/DVD/VCR/DVR to AUX 2 RCA Input connectors on the

back of the unit (RCA connection cable included). Make sure the color coded plugs

are attached to the corresponding color coded connectors on the device.

2. Press the POWER button to turn the unit on.

3. Select external audio input by pressing the AUX 2 button on the remote control or tap

the /MODE button on the main unit repeatedly to select AUX IN 2 mode, Mode

Indicator LED turns White.

4. The volume level can now be controlled through the main unit. Operate all other

functions on the external device as usual.

DIGITAL OPTICAL INPUT

NOTE: Digital Optical Cable is not included.

1. Ensure that the connections to the JSBW-210 are securely attached to the TV or

other audio device via Optical or Coaxial cables (not included).

2. Turn on the JSBW-210, press the OPTICAL Input button on remote control or

repeatedly tap the /MODE BUTTON on the main unit to select the OPTICAL

Input mode. LED indicator turns to Orange.

3. Operate your connected audio device directly for playback features.

4. Press the VOLUME +/- BUTTON on remote control or main unit to adjust the audio

level.

NOTE: If no sound is heard from the JSBW-210, make sure the audio (digital output)

setting of your source player (e.g. TV, DVD player, game player) is set to PCM.

AUXILIARY INPUT

This unit provides an auxiliary audio signal input jack for connecting external audio

devices like MP3 players, CD players and listen to them through the speakers of this

unit.

E13

1. Use an audio cable (included) with one 3.5 mm stereo plug on each end of the

cable.

2. Plug one end into the AUX 1 Input jack on the right hand side (top panel) of main unit

and the other end of the cable into the Line-out Jack or Headphone Jack of your

external audio device.

3. Turn on the external audio device and the main unit.

4. To select auxiliary audio input, press the AUX 1 Input button on remote control or tap

/MODE button on main unit repeatedly to select AUX IN 1 mode, Mode Indicator

LED turns Green.

5. The volume level can now be controlled through the main unit. Operate all other

functions on the auxiliary device as usual.

NOTE:

 If you connect this unit to the Line-Out Jack of your external device then you only

need to adjust the volume control of this unit. If you connected the Headphone Jack

of your external device then you may need to adjust both the volume control of your

external device and the volume control of this unit to find the most desirable volume

setting.

 Press the POWER button to turning off the unit when you finish listening. Don't

forget to switch off the power of your external device as well.

CARE AND MAINTENANCE

1. Do not subject the unit to excessive force, shock, dust or extreme temperature.

2. Do not tamper the internal components of the unit.

3. Clean your unit with a dry cloth. Solvent or detergent should never be used.

4. Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.

5. Keep your unit away from heating appliances and sources of electrical noise such as

fluorescent lamps or motors.

CLEANING THE UNIT

 To prevent fire or shock hazard, disconnect your unit from the AC power source

when cleaning.

 The finish on the unit may be cleaned with a dust cloth and cared for as other

furniture, Use caution when cleaning and wiping the plastic parts.

 If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any wax

or polish sprays on the cabinet.

 If the front panel becomes dirty or smudged with fingerprints it may be cleaned with

a soft cloth slightly dampened with a mild soap and water solution. Never use

abrasive cloths or polishes, as these will damage the finish of your unit.

CAUTION: Never allow any water or other liquids to get inside the unit while cleaning.

E14

TROUBLESHOOTING GUIDE

Should you experience difficulties in the use of this player please refer to the following chart or

call 1-800-777-5331 for Product Service and Support.

Symptom Possible Problem Solution

The unit is disconnected from

the AC outlet.

Reconnect to the AC outlet.

The unit does not

respond (no power)

The AC outlet has not power. Try the unit on another outlet.

Unit is ON but there

is low or no volume

The volume control has been

turned all the way down.

Turn the Volume control to a higher

output.

Bluetooth speaker is not linked

with the cell phone

Go through “Bluetooth Operations”

process to link the speakers.

No Sound

Speaker placement out of

range

Relocate the speaker within

Bluetooth operating range

Volume level is set too high. Decrease the volume.

If the external device original sound

source is of poor quality, distortion

and noise are easily noticed with

high-power speakers. Try a different

audio source such as a music CD .

Sound is distorted

Sound source is distorted.

If you are using an external sound

source like older generation of iPod,

try reducing the output volume on

the device itself. Also try turning

bass boost OFF or change the EQ

setting.

Unit gets warm after

extended play at

high volume

This is normal.

Turn the unit off for a period of time

or lower volume.

SPECIFICATION

Power requirement:

Main Unit AC-DC Adaptor DC 18V, 1.3 A

Remote Control

1 X DC 3V CR2025 lithium Battery

At Spectra, environmental and social responsibility is a

core value of our business. We are dedicated to

continuous implementation of responsible initiatives with

an aim to conserve and maintain the environment

through responsible recycling.

Please visit us at http://www.spectraintl.com/green.htm

for more information on

Spectra’s green initiatives or to find a recycler in your area.

E15

E16

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth

SIG, Inc. and any use of such marks by Spectra Merchandising Intl, Inc. is under

license. Other trademarks and trade names are those of their respective owners.

90 DAY LIMITED WARRANTY AND SERVICE

VALID IN THE U.S.A. ONLY

SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from defective

materials or factory workmanship for a period of 90 days from the date of original customer purchase and

provided the product is utilized within the U.S.A. This warranty is not assignable or transferable. Our

obligation under this warranty is the repair or replacement of the defective unit or any part thereof, except

batteries, when it is returned to the SPECTRA Service Department, accompanied by proof of the date of

original consumer purchase, such as a duplicate copy of a sales receipt.

You must pay all shipping charges required to ship the product to SPECTRA for warranty service. If the

product is repaired or replaced under warranty, the

return charges will be at SPECTRA’s expense. There

are no other express warranties other than those stated herein.

This warranty is valid only in accordance with the conditions set forth below:

1. The warranty applies to the SPECTRA product only while:

a. It remains in the possession of the original purchaser and proof of purchase is demonstrated.

b. It has not been subjected to accident, misuse, abuse, improper service, usage outside the

descriptions and warnings covered within the user manual or non-SPECTRA approved

modifications.

c. Claims are made within the warranty period.

2. This warranty does not cover damage or equipment failure caused by electrical wiring not in

compliance with electrical codes

or SPECTRA user manual specifications, or failure to provide

reasonable care and necessary maintenance as outlined in the user manual.

3. Warranty of all SPECTRA products applies to residential use only and is void when products are used

in a nonresidential environment or installed outside the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to

state. TO OBTAIN SERVICE please remove all batteries (if any) and pack the unit carefully and send it

freight prepaid to SPECTRA at the address shown below. IF THE UNIT IS RETURNED WITHIN THE

WARRANTY PERIOD shown above, please include a proof of purchase (dated cash register receipt) so

that we may establish your eligibility

for warranty service and repair of the unit without cost. Also include

a note with a description explaining how the unit is defective. A customer service representative may

need to contact you regarding the status of your repair, so please include your name, address, phone

number and email address to expedite the process.

IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $45.00 to cover the

cost of repair, handling and return postage. All out of warranty returns must be sent prepaid.

It is recommended that you contact SPECTRA first at 1-800-777-5331 or by email at

[email protected]

for updated information on the unit requiring service. In some cases the

model you have may be discontinued, and SPECTRA reserves the right to offer alternative options for

repair or replacement.

SPECTRA MERCHANDISING INTERNATIONAL, INC.

4230 North Normandy Avenue,

Chicago, IL 60634, USA.

1-800-777-5331

To register your product, visit the link on the website below to enter your information.

http://www.spectraintl.com/wform.htm

0316 Printed in China

PUEDE COLOCARSE EN LA PARED 2.0 BLUETOOTH

SOUND BAR

Model: JSBW-210

Manual del Propietario

POR FAVOR LEA CUIDADOSAMENTE ESTE MANUAL DEL USUARIO EN SU TOTALIDAD, ANTES

DE OPERAR ESTA UNIDAD Y GUÁRDELO PARA REFERENCIA POSTERIOR.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Esta unidad ha sido diseñada y fabricada para proteger su seguridad personal cuando

se utiliza según las instrucciones. Sin embargo, si se usa de forma inadecuada se

corre el riesgo de recibir una descarga eléctrica o de causar incendio. Por favor, lea

todas las instrucciones de seguridad y funcionamiento de la unidad antes de instalarla

y usarla, y manténgalas a mano para referencia posterior. Preste atención a todas

las advertencias en estas instrucciones y en la unidad.

1. Lea las instrucciones - Todas las instrucciones de seguridad y funcionamiento

deben leerse antes de utilizar el aparato.

2. Conserve estas instrucciones - Las instrucciones de seguridad y funcionamiento

deben guardarse para futuras consultas.

3. Preste atención a todas las advertencias - Todas las advertencias en el aparato y

en las instrucciones de operación deben ser atendidas.

4. Siga todas las instrucciones - Todas las instrucciones de operación y uso deben

ser seguidas.

5. No utilice este aparato cerca del agua - El aparato no debe utilizarse cerca del

agua; por

ejemplo, cerca

de una bañera, lavabo, fregadero de cocina, lavadero,

en un sótano húmedo o cerca de una piscina.

6. Limpie sólo con un paño seco - El aparato sólo debe limpiarse según lo

recomendado por el fabricante.

7. No bloquee las aberturas de ventilación. Instale de acuerdo con las instrucciones

del fabricante. El aparato debe situarse de modo que su ubicación o posición no

interfiera con una ventilación adecuada. Por ejemplo, el aparato no debe situarse

en una cama, sofá, alfombra o superficie similar que pueda bloquear las aberturas

de ventilación; o colocado en una instalación integrada, como una estantería o

armario que pueda impedir el flujo de aire a través de las aberturas de ventilación.

8. No lo instale cerca de fuentes de calor, como radiadores, calentadores, estufas u

otros aparatos (incluyendo amplificadores) que produzcan calor.

9. Adaptador de CA se utiliza como dispositivo de desconexión y debe permanecer

fácilmente accesible durante el uso. Para desconectar el aparato completamente

de la red, el adaptador de CA debe desconectarse forma la

toma de corriente por

completo.

10. Use sólo adaptadores / accesorios especificados por el fabricante.

11. Use sólo con un carro, base, trípode, soporte o mesa especificados

por el fabricante, o vendidos con el aparato. Cuando se utiliza un

carro, tenga cuidado al mover la combinación de carro / aparato para

evitar daños por vuelco.

12. Desenchufe el aparato durante las tormentas eléctricas o cuando no lo utilice

durante largos períodos de tiempo.

13. Consulte siempre al personal de servicio cualificado. Se requiere servicio cuando

el aparato ha sido dañado de alguna manera, como cuando el cable de

alimentación o el enchufe están dañados, se ha derramado líquido o han caído

objetos dentro del aparato, el aparato ha sido expuesto a la lluvia o humedad, si

no funciona con normalidad , o se ha caído.

14. Este aparato no debe ser expuesto a goteos o salpicaduras de agua y que ningún

objeto lleno de líquido como jarrones se colocará sobre el aparato.

15. Fuentes de alimentación - El aparato debe conectarse a una fuente de energía

únicamente del tipo descrito en

las instrucciones de operación o como indicado en

el aparato. No sobrecargue la toma de pared.

16. La batería no debe exponerse a calor excesivo como el del sol, fuego o similares

17. Existe peligro de explosión si la batería se sustituye de forma incorrecta.

Reemplace sólo con el mismo tipo o equivalente.

18. No intente desmontar, abierta o reparar este producto usted mismo. Si se produce

un fallo, consulte a su técnico de servicio cualificado local o ponerse en contacto

con el distribuidor a través del número de teléfono en la parte posterior de este

manual de instrucciones.

19. La señal de precaución y la placa de identificación se encuentra en la parte inferior

del producto

NOTAS IMPORTANTES

Evite instalar la unidad en los lugares descritos a continuación:

Lugares expuestos a la luz solar directa o cerca de aparatos que irradien calor,

tales como calentadores eléctricos.

Lugares expuestos a vibraciones constantes.

Polvoriento, húmedo o lugares húmedos.

Las fuentes de ruido eléctrico, como lámparas fluorescentes o motores.

En caso de mal funcionamiento debido a descargas electrostáticas, el aparato tiene

que ser reajustada por desconectarlo de

la red eléctrica, espere por lo menos

durante 60 segundos antes de volver a conectar el cable de alimentación de

corriente alterna.

COMUNICACIONES (FCC POR SUS SIGLAS EN INGLÉS)

Este dispositivo se conforma con la parte 15 de las reglas de la FCC. La operación

está conforme a las dos condiciones siguientes:

(1) este dispositivo puede no causar interferencia dañosa, y

(2) este dispositivo debe aceptar cualquier interferencia recibida, incluyendo

interferencia que pueda causar la operación indeseada.

NOTA : Este equipo ha sido probado y se ha determinado que satisface los límites para

un dispositivo digital clase B, de acuerdo a lo que dispone la Parte 15 de los

Reglamentos de la FCC, Estos limites tienen el propósito de proporcionar una

protección razonable contra interferencia dañina en una instalación residencial. Este

equipo genera, usa y puede emitir energía de radiofrecuencia, y su no se instala y se

usa de acuerdo con estas instrucciones, puede causar interferencia dañina a las

radiocomunicaciones. Sin embargo, no hay ninguna garantía de que no vaya a ocurrir

interferencia en ninguna instalación determinada. Si este equipo causa interferencia no

deseada contra la recepción de r

adio o televisión, lo cual se puede determinar

encendiendo y apagando el aparato, se exhorta al usuario a tratar de corregir el

problema de la interferencia tomando una o mas de las siguientes medidas:

- Reoriente o reubique la antena de recepción

- Aumente la distancia de separación entre el equipo y el receptor

- Conecte el equipo a un receptáculo en un circuito distinto al que usa el receptor.

- Consulte al concesionario o a un radiotécnico experimentado para que le ayuden.

ADVERTENCIA

Los cambios o modificaciones a esta unidad que no estén expresamente aprobados

por la parte responsable de la conformidad podrían anular la autoridad del usuario para

operar el equipo.

¡PROTEJA SUS MUEBLES!!

Este sistema está equipado con soportes de goma anti deslizante para prevenir que el

equipo se mueva mientras usted opera los controles. Éstos soportes están realizados

en un material de goma no deslizante especialmente formulado para evitar dejar

Page is loading ...

Jensen JSBW-210 User manual

Brand: Jensen

Model: JSBW-210

Category: Bluetooth music receivers

Type: User manual

Download PDF

report

in other languages

español: Jensen JSBW-210 Manual de usuario

Jensen JSBW-210 User manual

Jensen JSBW-210 User manual

in other languages

Related papers

Other documents