Ecler CKL SM115 User manual

USER MANUAL

MANUAL DE INSTRUCCIONES

NOTICE D'UTILISATION

BEDIENUNGSANLEITUNG

CKL3000T

CKL5000T

CKL7000T

Page is loading ...

3

INSTRUCTION MANUAL

1. IMPORTANT REMARK 04

1.1. Safety precautions 04

2. INTRODUCTION 04

3. INSTALLATION 06

3.1. Placement and mounting 06

3.2. Rigging CKL110T and CKL SM115 enclosures 07

3.3. Accessories 08

3.4. Connecting the system 08

4. TECHNICAL CHARACTERISTICS 27

5. DIAGRAMS 28

All numbers subject to variation due to production tolerances. ECLER SA reserves the right to make changes or

improvements in manufacturing or design which may affect specifications.

4

1. IMPORTANT REMARK

Congratulations! You are the owner of a carefully designed and manufactured equipment. We

thank you for having purchased our CKL-T processed system.

It is VERY IMPORTANT that you read this manual before connecting the system, in order to

obtain its maximum performance.

We recommend our authorised Technical Services whenever any maintenance task should be

needed so that optimum operation shall be achieved.

1.1. Safety precautions

CKL-T systems are capable to deliver maximum sound pressure levels greater than 143dB SPL

at 1m. This sound pressure levels can cause permanent damage to human hearing. Protect your

ears when working at high power and next to the system.

CKL-T sound systems have been designed to operate exclusively with ECLER amplifiers and

DP300 (CKL7000T) or AMIC card (CKL5000T, CKL3000T) digital processors which not only offer a well-

balanced sound, but also ensuring perfect operating safety. Using other components than the specified

ones, be it from ECLER or from other manufacturers, will both worsen the system performance and

mean a risk of serious damage to your loudspeakers.

2. INTRODUCTION

The CKL-T systems have been specially designed for both fix and mobile applications that call for

excellent performance and sound quality.

Depending on the model, CKL-T system is constituted by de following items:

SYSTEM LOUDSPEAKER CABINETS PROCESSOR POWER AMPLIFIERS

CKL7000T

2 CKL-110T

2 CKL SM-115T

4 DPC118

1 DP300

1 DPA1400

1 DT4800

1 DT6800

SYSTEM LOUDSPEAKER CABINETS PROCESSOR POWER AMPLIFIERS

CKL5000T

2 CKL-110T

4 DPC118

1 AMIC

1 DPA1400

1 DT6800

SYSTEM LOUDSPEAKER CABINETS PROCESSOR POWER AMPLIFIERS

CKL3000T

2 CKL-110T

2 DPC118

1 AMIC

1 DPA1400

1 DT6800

Both ECLER DP300 (CKL7000T system) and AMIC card (CKL5000T and CKL3000T systems)

perform, among other parameters, the equalization of each of the loudspeaker cabinets and accurate

limiting, specially set for protecting each of the systems.

5

STEP BY STEP THROUGH CKL-T SYSTEMS

PLUG AND PLAY COMPACT SYSTEMS

In the last years, the evolution of professional sound systems has been certainly influenced by

two facts: The reduction of acoustic cabinet size and the ever increasing output power of amplifiers.

Systems are now lighter, smaller and more portable, while the sound quality approaches more and more

that of a Hi-Fi system. Electronics is the key of this advances. The components generally called

"processors" are able to push a sound system to its limits. These intelligent electronic systems,

sometimes contained in the amplifier itself, but in most cases mounted into dedicated processor units,

constantly monitor the systems operating conditions. The result is a total reliability as far as the systems

behaviour is concerned, which is the main obsession when installing professional sound systems.

CKL-T systems are based in two or three loudspeaker cabinets (depending on version): each of

them is perfectly tailored to work in its optimum range of frequencies. Hence resulting in a well-balanced

system efficiently capable of reproducing any program, be it vocal or any other music content.

CKL110T LOUDSPEAKER CABINETS (CKL7000T, CKL5000T and CKL3000T systems)

Small-dimensioned trapezoidal acoustic enclosure for mid-high frequency reproduction.

Assembled with 18mm thick birch plywood from Finland covered with a scratch and shock resistant

polyurethane paint finish. Internally reinforced. The mid frequency way employs an enclosed 10’’

speaker with neodymium motor and carbon fibre compound diaphragm attached to a Tractix horn, which

is equipped with a phase corrector. The high frequency way uses a 2’’ compression driver with pure

titanium diaphragm, neodymium motor and a 60º x 40º constant directivity diffusor. The speakers are

protected against shocks, dust and splashes by a metal grille and an acoustically transparent foam.

Incorporates handles for their transport.

The on-axis frequency response within a 3dB margin lies between 170Hz and 19kHz.

The efficiency or sensitivity, which is sound pressure level (SPL) at 1m and 1W power input,

reaches remarkable 112dB. The maximum SPL produced at 1m reaches 141dB SPL.

The system includes a passive LC filter with low tolerance polyester capacitors and large

cross-section wire coils. The high frequency way also features a protection system against Larsen effect

feedback and signal clipping.

The maximum RMS power is 350W RMS at 8, while the program power capacity is 700W at

8.

CKL SM115 LOUDSPEAKER CABINET (Only CKL7000T system)

Low-dimensioned trapezoidal acoustic enclosure for mid-low frequency playback. Bandpass type

acoustical design. Assembled with 18 mm thick birch plywood from Finland covered with a scratch and

shock resistant polyurethane paint finish. Internally reinforced. It employs a high performance 15’’

speaker attached to a horn in order to increase efficiency. The speaker is protected against shocks, dust

and splashes by a metal grille and an acoustically transparent foam. Incorporates handles for their

transport.

The on-axis frequency response within a 3dB margin lies between 70Hz and 280Hz.

6

The efficiency or sensitivity, which is sound pressure level (SPL) at 1m and 1W power input, is

105dB. The maximum SPL produced at 1m reaches 136dB SPL.

The maximum RMS power is 600W RMS at 8, while the program power capacity is 1200W at

8.

DPC118 LOUDSPEAKER CABINET (CKL7000T, CKL5000T and CKL3000T systems)

Low-dimensioned loudspeaker cabinet for low frequency playback. Bandpass type acoustical

design. Assembled with 18 mm thick birch plywood from Finland covered with a scratch and shock

resistant polyurethane paint finish.

It employs a high performance 18’’ speaker attached to a horn in order to increase efficiency. The

speaker is protected against shocks, dust and splashes by a metal grille and an acoustically transparent

foam. Provided with 3 lateral handles.

The efficiency or sensitivity, which is sound pressure level (SPL) at 1m and 1W power input, is

106dB. The maximum SPL produced at 1m reaches 140dB SPL.

The maximum RMS power is 1100W RMS at 8, while the program power capacity is 2200W at 8.

3. INSTALLATION

3.1. Placement and mounting

As a general rule and due to its portable conception, staking

loudspeaker cabinets is the recommended way of setting CKL-T system.

This means mounting CKL100T (i.e., CKL7000T system) on top of CKL

SM115 cabinet and this on top on DPC118 units.

The bass reinforcement cabinets DPC118 should be paired so that

their marks are face to face (see diagram).

Bass enclosures are more efficient when placed directly on the floor

in landscape orientation rather than vertical for a better sound quality.

Additionally, the acoustic conditions of the venue as well as the

audience number, should be taken into account. Following general

guidelines must be considered:

Always place acoustic enclosures on solid and firm ground.

No obstacles should lie between the loudspeaker and the audience. High frequencies, as

opposed to low frequencies, tend to be much more directional and any obstacle in the acoustic wave

path represents attenuation in the frequency response of the system. For large audiences better sound

propagation will be obtained if loudspeaker cabinets are placed in a higher position.

Avoid exposing the system to sun for long periods and to rain.

7

3.2. Rigging CKL110T and CKL SM115 enclosures

Following general guidelines must be considered:

Always fly loudspeaker cabinets from a solid and firm surface.

No obstacles should lie between the loudspeaker and the

audience.

High frequencies, as opposed to low frequencies, tend to be

much more directional and any obstacle in the acoustic wave path

represents attenuation in the frequency response of the system.

CKL110T and CKL SM115 feature an effective rigging system,

the same type as used in air cargo shipments (ISO 7166 standard),

consisting in 6 adjustable cargo rails, which allow flying single speaker

enclosures or complex combinations of several enclosures. Two rails

are placed at each side and two at the rear wall of the cabinet. The

fittings at the side are internally connected with a metal brace. These

side fittings allow flying the enclosure. Finally, the rear rails allow tilting

the enclosure or group of enclosures.

Each position of the aeronautic specified cargo restraint track has a maximum load capacity of

180kg, considering the enclosure is correctly flown, as shown in the diagrams.

The tracking system works in combination with Ecler ADP cargo restraint double stud and ring.

(Adam Hall Ref. 5740)

The total load capacity of the structure is limited by this track and is 180kg per anchor point

(360kg total).

It is very important to keep in mind that these values are only valid if the load is suspended

perpendicularly. Load capacity varies as a function of the angle according to following table:

Always make sure that the anchor points are firmly

attached to the rail and locked.

IMPORTANT

The rear rails have been designed basically for tilting the enclosures. They should not carry any

weight.

ATTENTION

The chains or steel cables used to

suspend the enclosures should

always run parallel to the vertical axis

of the loudspeaker cabinet. They must not

show a wider angle.

Angle

0º 45º 90º

Load capacity

180kg 170kg 160kg

0º

180kg 170kg

45º

160kg

90º

8

3.3. Accessories

Following accessories are available to complement CKL-T

systems:

 ADP: cargo restraint double stud and ring. Allows

CKL110T and CKL SM115 rigging.

 BAGCKLT: CKL110T and CKL SM115 storage and

transportation bag.

 BAGDPC118: DPC118 storage and transportation bag.

 WH200: four-piece castor wheel set, suitable for the QRA

kit.

 QRA: four fittings set. Allow assembly of WH200 castor

wheels on DPC118 unit.

It is also possible to fit all system electronics into a flight

case (ref CKLFL3 for CKL7000T system or CKLFL for CKL5000T

and CKL3000T systems). 10m connection cables are included

apart from the internal wiring and connection panel.

3.4. Connecting the system

Connection to the acoustic cabinet. This connection must be done with, at least, 3mm cable (we

recommend 6mm). The amplifier output and any of the acoustic cabinets input connectors are

SPEAKON, being only used 1+ LIVE and 1- GND pins.

When more than one system is used, no matter which model, STACK outputs available at

connection panel should be employed. STACK outputs of any of the amplifiers of the given system can

be also used for this purpose. Please, in any case use proper quality wiring.

CAUTION:

USE EXTERNAL FILTER OR PROCESSOR

made by ecler s.a. barcelona spain

ACTIVE C ABI NET

STACK OUTPUT

DPC118

LOUDSPEAKER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

Page is loading ...

27

4. TECHNICAL CHARACTERISTICS 4. CARACTERÍSTICAS TÉCNICAS

4. CARACTÉRISTIQUES TECHNIQUES 4. TECHNISCHE DATEN

CKLFL3000 CKLFL5000 CKLFL7000

Power (*) 2710W RMS 4378W RMS 5778W RMS

Maximum SPL @ 1m 141dB 142dB 143dB

Frequency response (-3dB) 50Hz-19kHz 50Hz-19kHz 50Hz-19kHz

Radiation angles (H-V) (Treble) 60ºx40º 60ºx40º 60ºx40º

Power consumption (max) 5370VA 5370VA 8095VA

Overall weight 30kg. 30kg. 42kg.

(without flight-case, cables & loudspeakers)

CKL110T CKL SM115 DPC118

Dimensions (Height x Width x Depth) 550x550x650mm 550x550x650mm 570x750x720mm

Weight 47kg. 37kg. 60kg.

Remaining characteristics: see individual specifications.

DT4-6800: Maximum RMS total output power at 0,3% THD, 1kHz & independent from warm up time.

DPA1400: RMS total output power at 1% THD, 1kHz.

28

5. DIAGRAMS 5. DIAGRAMAS

5. SCHÉMAS 5. DIAGRAMME

TO MIXER

CAUTION:

USE EXTER NAL F ILTER OR PROCESSO R

made by ecler s.a. barcelona spain

ACTIVE CABI NET

STACK OUTPUT

DPC118

LOUDSPEAKER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

STACK OUTPUT

made by ecler s.a. barcelona spain

LOUDSPEA KER

CKL SERIES

CABINET

N.C.2+

N.C.2-

GND

LIVE

1-

1+

INPUT

CAUTION:

USE EXTERN AL FIL TER OR PROCESSOR

made by ecler s.a. barc elona sp ain

ACTIVE CABINET

STACK OUTPUT

DPC118

LOUDSPEA KER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

STACK OUTPUT

made by ecler s.a. barcelona spain

LOUDSPEAK ER

CKL SERIES

CABINET

N.C.2+

N.C.2-

GND

LIVE

1-

1+

INPUT

LEFT

RIGHT

STACK

MAINS AUX

OUTPUT

MAINS

INTPUT

CKL110T

DPC118 DPC118

CKLFL3000

CKL110T

MAINS INPUT MAINS AUX OUTPUT HIGH LOW STACK INPUT

HIGH LOW STACK INPUT

LEFT

RIGHT

PIN 1+ = OUT+ / PIN 1- = OUT- / PIN 2+ = N.C. / PIN 2- = N.C. PIN 1 = GND / PIN 2 = HOT / PIN 3 = COLD

2WPATCH

CAUTION: RISK OF ELEC TRIC SHOCK

29

TO MIXER

CAUTION:

USE EXTE RNAL F ILTER OR PROCESS OR

made by ecler s.a. barcelona spain

ACTIVE CABINET

STACK OUTPUT

DPC118

LOUDSPEAKER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

CAUTION:

USE EXTE RNAL F ILTER OR PROCESS OR

made by ecler s.a. barcelona spain

ACTIVE CABINET

STACK OUTPUT

DPC118

LOUDSPEAKER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

STACK OUTPUT

made by ecl er s. a. barc elona sp ain

LOUDSPEAKER

CKL SERIES

CABINET

N.C.2+

N.C.2-

GND

LIVE

1-

1+

INPUT

CAUTION:

USE EXTERNAL FILTER OR PROCESSOR

made by ecler s.a. barcelona spain

ACTIVE CA BINET

STACK O UTPUT

DPC118

LOUDSPEAKER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

CAUTION:

USE EXTERNAL FILTER OR PROCESSOR

made by ecler s.a. barcelona spain

ACTIVE CA BINET

STACK O UTPUT

DPC118

LOUDSPEAKER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

STACK OUTP UT

made by ecler s.a. barcelona spain

LOUDSPEAKER

CKL SERIES

CABINET

N.C.2+

N.C.2-

GND

LIVE

1-

1+

INPUT

LEFT

RIGHT

STACK

MAINS AUX

OUTPUT

MAINS

INTPUT

CKL110T

DPC118

DPC118 DPC118

DPC118

CKLFL5000

CKL110T

MAINS INPUT MAINS AUX OUTPUT HIGH LOW STACK INPUT

HIGH LOW STACK INPUT

LEFT

RIGHT

PIN 1+ = OUT+ / PIN 1- = OUT- / PIN 2+ = N.C. / PIN 2- = N.C. PIN 1 = GND / PIN 2 = HOT / PIN 3 = COL D

2WPATCH

CAUTION: RISK O F ELECTRIC SHOCK

30

TO MIXER

CAUTION:

USE EXTERNA L FIL TER OR PROC ESSOR

made by ecler s.a. barcelona spain

ACTIVE CABINET

STACK OUTPUT

DPC118

LOUDSPEAKER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

CAUTION:

USE EXTERNA L FIL TER OR PROC ESSOR

made by ecler s.a. barcelona spain

ACTIVE CABINET

STACK OUTPUT

DPC118

LOUDSPEAKER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

STACK OUTPUT

made by ecler s. a. barc elona sp ain

LOUDSPEAKER

CKL SERIES

CABINET

N.C.2+

N.C.2-

GND

LIVE

1-

1+

INPUT

STACK OUTPUT

made by ecler s. a. barc elona sp ain

LOUDSPEAKER

CKL SERIES

CABINET

N.C.2+

N.C.2-

GND

LIVE

1-

1+

INPUT

CAUTION:

USE EXTERNA L FIL TER O R PROC ESSOR

made by ecler s.a. barcelona spain

ACTIVE CABINET

STACK OUTPUT

DPC118

LOUDSP EAKER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

CAUTION:

USE EXTERNA L FIL TER O R PROC ESSOR

made by ecler s.a. barcelona spain

ACTIVE CABINET

STACK OUTPUT

DPC118

LOUDSP EAKER

CABINET

IMPEDANCE: 8

1+ LIVE

1- GND

2+ N.C.

2- N.C.

INPUT

STACK OUTPUT

made by ecler s.a. barcelona spain

LOUDSPEAKER

CKL SERIES

CABINET

N.C.2+

N.C.2-

GND

LIVE

1-

1+

INPUT

STACK OUTPUT

made by ecler s.a. barcelona spain

LOUDSPEAKER

CKL SERIES

CABINET

N.C.2+

N.C.2-

GND

LIVE

1-

1+

INPUT

LEFT

RIGHT

STACK

MAINS AUX

OUTPUT

MAINS

INTPUT

CKL110T

CKL SM115T

DPC118

DPC118 DPC118

DPC118

CKLFL7000

CKL110T

CKL SM115T

MAINS INPUT MAINS AUX OUTPUT HIGH MID LOW STACK INPUT

HIGH MID LOW STACK INPUT

LEFT

RIGHT

PIN 1+ = OUT+ / PIN 1- = OUT- / PIN 2+ = N.C. / PIN 2- = N.C. PIN 1 = GND / PIN 2 = HOT / PIN 3 = COLD

3WPATCH

CAUTION: RISK OF ELECTRIC SHOCK

Page is loading ...

32

ECLER Laboratorio de electro-acústica S.A.

Motors 166-168, 08038 Barcelona, Spain

INTERNET http://www.ecler.com E-mail: [email protected]

50.0132.01.00

Ecler CKL SM115 User manual

This manual is also suitable for

Ecler CKL SM115 User manual

in other languages

Related papers

Other documents