Cisco UCS-CPU-E52403B= Datasheet

Brand: Cisco

Model: UCS-CPU-E52403B=

Category: Processors

Type: Datasheet

CISCO SYSTEMS PUBLICATION HISTORY

170 W

EST TASMAN DR.

AN JOSE, CA, 95134 REV B.6 MARCH 2, 2015

WWW.CISCO.COM

Spec Sheet

Cisco UCS B22 M3

Blade Server

Cisco UCS B22 M3 Blade Server

OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

DETAILED VIEWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Blade Server Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

BASE SERVER STANDARD CAPABILITIES and FEATURES . . . . . . . . . . . . . . . . . 5

CONFIGURING the SERVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

STEP 1 VERIFY SERVER SKU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

STEP 2 CHOOSE CPU(S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

STEP 3 CHOOSE MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

STEP 4 CHOOSE HARD DISK DRIVES or SOLID STATE DRIVES (OPTIONAL) . . . . . . . . . . . . . . 14

STEP 5 CHOOSE ADAPTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

STEP 6 ORDER A TRUSTED PLATFORM MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

STEP 7 ORDER CISCO FLEXIBLE FLASH SECURE DIGITAL CARDS . . . . . . . . . . . . . . . . . . . . 21

STEP 8 ORDER OPTIONAL INTERNAL USB 2.0 DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

STEP 9 CHOOSE OPERATING SYSTEM AND VALUE-ADDED SOFTWARE . . . . . . . . . . . . . . . . 24

STEP 10 CHOOSE OPERATING SYSTEM MEDIA KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

STEP 11 CHOOSE SERVICE and SUPPORT LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

ORDER OPTIONAL KVM LOCAL I/O CABLE* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

SUPPLEMENTAL MATERIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

DIMM and CPU Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

DIMM Population . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Recommended DIMM Populations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Upgrade and Servicing-Related Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Drive and Blade Server Blanking Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Adding an Additional CPU (with CPU heat sink) . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Motherboard Lithium Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

CPU Removal and Installation (“pick n place”) Tool Set . . . . . . . . . . . . . . . . . . . . . 40

Thermal Grease (with syringe applicator) for CPU to Heatsink Seal . . . . . . . . . . . . . . 40

Air Baffle Replacement Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

CPU Heat Sink Cleaning Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Network Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

VIC 1240 Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Mezzanine Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

B22 M3 Configured with 1 CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Connectivity using the Cisco UCS 2208XP Fabric Extender . . . . . . . . . . . . . . . . 45

Connectivity using the Cisco UCS 2204XP Fabric Extender . . . . . . . . . . . . . . . . 45

Connectivity using the Cisco UCS 2104XP Fabric Extender . . . . . . . . . . . . . . . . 46

B22 M3 Configured with 2 CPUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Connectivity using the Cisco UCS 2208XP Fabric Extender . . . . . . . . . . . . . . . . 47

Connectivity using the Cisco UCS 2204XP Fabric Extender . . . . . . . . . . . . . . . . 50

Connectivity using the Cisco UCS 2104XP Fabric Extender . . . . . . . . . . . . . . . . 53

TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Cisco UCS B22 M3 Blade Server

OVERVIEW

The Cisco® UCS B22 M3 Blade Server delivers a balanced price/performance feature set to address quick

deployment of scalable IT infrastructure and Web 2.0 applications. The Cisco UCS B22 M3 harnesses the

power of the latest latest Intel® Xeon® E5-2400 v2 and E5-2400 series processor family CPUs with

expandability to 384 GB of RAM (using 32 GB DIMMs), 2 hot-plug drives, and 2 PCIe mezzanine adapter slots

for up to 80 Gbps throughput.

Figure 1 Cisco UCS B22 M3 Blade Server

Cisco UCS B22 M3 Blade Server

DETAILED VIEWS

Blade Server Front View

Figure 2 is a detailed front view of the Cisco UCS B22 M3 Blade Server.

Figure 2 Blade Server Front View

1 Asset pull handle

(a blank asset tag is provided on which

you can add your own label or sticker or

you can use a marker to write your asset

information on the tag)

7 Network link status LED

2 Blade ejector handle 8 Blade health LED

3 Ejector captive screw 9

Console connector

Notes

1. For information about the KVM local I/O cable that plugs into the console connector (a cable is included with

every Cisco UCS 5100 Series blade server chassis accessory kit), see ORDER OPTIONAL KVM LOCAL I/O CABLE*

on page 32.

4 Drive bay 1 10 Reset button access

5 Drive bay 2 11 Beaconing LED and button

6 Power button and LED — —

UCS B22 M3

1 2 3

4 5

332661

Cisco UCS B22 M3 Blade Server

BASE SERVER STANDARD CAPABILITIES and FEATURES

Table 1 lists the capabilities and features of the base server. Details about how to configure the server for

a particular feature or capability (for example, number of processors, disk drives, or amount of memory)

are provided in

CONFIGURING the SERVER on page 7.

Table 1 Capabilities and Features

Capability/Feature Description

Chassis The UCS B22 M3 Blade Server mounts in a Cisco UCS 5100 series blade server

chassis

CPU One or two Intel® E5-2400 v2 or E5-2400 series processor family CPUs

Chipset Intel® C600 series chipset

Memory 12 total slots for registered ECC DIMMs for up to 384 GB total memory

capacity (using 32 GB DIMMs)

I/O Mezzanine adapters:

■ Adapter slot 1 for Cisco’s VIC 1240 adapter, which provides Ethernet and

Fibre Channel over Ethernet (FCoE)

■ Adapter slot 2 for various types of Cisco, Emulex, or QLogic network I/O

adapters or Cisco UCS Storage Accelerator adapters

Storage controller LSI Logic SAS 2002 integrated controller

■ 6 Gbs SAS/SATA support

■ RAID 0 and 1

Internal storage devices Up to two optional, front-accessible, hot-swappable 2.5-inch small form

factor (SFF) SAS or SATA solid-state disks (SSDs) or hard disk drives (HDDs).

An internal USB 2.0 port is also supported. A 4 GB USB 2.0 device is available

from Cisco.

NOTE: Adapter slot 2 is supported only for 2-CPU system

configurations.

NOTE: The integrated RAID controller does not implement a write

cache. However, servers that implement two HDDs and RAID

controllers with cache lack the ability to match the performance

of RAID’ed SSDs without cache, as implemented in this server.

Cisco UCS B22 M3 Blade Server

BASE SERVER STANDARD CAPABILITIES and FEATURES

Video The Emulex Pilot 3 Integrated Baseboard Management Controller provides

video:

■ Matrox G200e video controller

■ Integrated 2D graphics core with hardware acceleration

■ Supports all display resolutions up to 1920 x 1200 x 16 bpp resolution at

60 Hz

■ 24-bit color depth for all resolutions less than 1600x1200

■ 8 MB video memory

Interfaces ■ Front panel

• One console connector (see ORDER OPTIONAL KVM LOCAL I/O

CABLE* on page 32)

Power subsystem Integrated in the Cisco UCS 5100 series blade server chassis

Fans Integrated in the Cisco UCS 5100 series blade server chassis

Integrated management

processor

The built-in Cisco Integrated Management Controller (CIMC) GUI or CLI

interface enables you to monitor the server inventory, health, and system

event logs.

Cisco UCS Diagnostics

for Cisco UCS B-Series

Blade Servers

The Cisco UCS Blade Server Diagnostics tool for Cisco UCS Blade Servers

enables you to verify the health of the hardware components on your

servers. The diagnostics tool provides a variety of tests to exercise and

stress the various hardware subsystems on the Cisco UCS Blade Servers, such

as memory and CPU. You can use the tool to run a sanity check on the state

of your Cisco UCS Blade Servers after you fix or replace a hardware

component. You can also use this tool to run comprehensive burn-in tests

before you deploy a new Cisco UCS Blade Server in your production

environment.

See the following links for more information:

User Guide:

http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/ucs_di

agnostics/b_UCS_Blade_Server_Diagnostics_User_Guide.html

ISO Download:

http://www.cisco.com/cisco/software/navigator.html

Table 1 Capabilities and Features (continued)

Capability/Feature Description

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

Follow these steps to configure the Cisco UCS B22 M3 Blade Server:

■ STEP 1 VERIFY SERVER SKU, page 8

■ STEP 2 CHOOSE CPU(S), page 9

■ STEP 3 CHOOSE MEMORY, page 11

■ STEP 4 CHOOSE HARD DISK DRIVES or SOLID STATE DRIVES (OPTIONAL), page 14

■ STEP 5 CHOOSE ADAPTERS, page 16

■ STEP 6 ORDER A TRUSTED PLATFORM MODULE, page 20

■ STEP 7 ORDER CISCO FLEXIBLE FLASH SECURE DIGITAL CARDS, page 21

■ STEP 8 ORDER OPTIONAL INTERNAL USB 2.0 DRIVE, page 22

■ STEP 9 CHOOSE OPERATING SYSTEM AND VALUE-ADDED SOFTWARE, page 23

■ STEP 10 CHOOSE OPERATING SYSTEM MEDIA KIT, page 26

■ STEP 11 CHOOSE SERVICE and SUPPORT LEVEL, page 27

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

STEP 1 VERIFY SERVER SKU

Verify the product ID (PID) of the server as shown in Table 2.

The base Cisco UCS B22 M3 blade server does not include the following components. They are to

be selected during product ordering:

■ CPU(s)

■ Memory

■ Disk drives

■ VIC 1240 adapter

■ Emulex or QLogic I/O adapters

■ Cisco UCS Storage Accelerators

Table 2 PID of the Base UCS B22 M3 Blade Server

Product ID (PID) Description

UCSB-B22-M3 UCS B22 M3 Blade Server without CPU, memory, HDD, VIC 1240 adapter, or

mezzanine adapters

NOTE: Use the steps on the following pages to order the UCS B22 M3

server with the configurable components that you want configured.

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

STEP 2 CHOOSE CPU(S)

The standard CPU features are:

■ Intel Xeon processor E5-2400 v2 or E5-2400 series processor family CPUs

■ Intel C600 series chipset

■ Cache sizes of up to 25 MB

Select CPUs

The supported Intel Xeon E5-2400 v2 and E5-2400 series family CPUs on the UCS B22 M3 are

listed in

Table 3.

Table 3 Supported Intel CPUs: E5-2400 v2 and E5-2400 Series Processor Family CPUs

Product ID (PID)

Intel

Number

Clock

Freq

(GHz)

Power

(W)

Cache

Size (MB)

Cores QPI

Highest DDR3 DIMM

Clock Support (MHz)

Notes

1. If higher or lower speed DIMMs are selected than what is shown in the table for a given CPU, the DIMMs will be

clocked at the lowest common denominator of CPU clock and DIMM clock. For example:

Selecting lower-speed DIMMs

: If you use an E4-2470 CPU (which can support up to 1600-MHz DIMMs) with 1333-MHz

DIMMs, the DIMMs will be clocked at the lower speed of 1333 MHz.

Selecting higher-speed DIMMs:

If you use 1600-MHz DIMMs with an E5-2420 CPU (which can support up to 1333-MHz

DIMMs), the DIMMS will be clocked at the lower speed of 1333 MHz.

Intel Xeon E5-2400 v2

UCS-CPU-E52470B E5-2407 v2 2.4 95 25 10 6.4 GT/s 1600

UCS-CPU-E52450B E5-2450 v2 2.5 95 20 8 7.2 GT/s 1600

UCS-CPU-E52440B E5-2440 v2 1.90 95 20 8 7.2 GT/s 1600

UCS-CPU-E52430LB E5-2430L v2 2.40 60 15 6 7.2 GT/s 1600

UCS-CPU-E52420B E5-2420 v2 2.20 80 15 6 7.2 GT/s 1600

UCS-CPU-E52407B E5-2407 v2 2.40 80 10 4 6.4 GT/s 1333

UCS-CPU-E52403B E5-2403 v2 1.80 80 10 4 6.4 GT/s 1333

Intel Xeon E5-2400

UCS-CPU-E5-2470 E5-2470 2.30 95 20 8 8 GT/s 1600

UCS-CPU-E5-2450 E5-2450 2.10 95 20 8 8 GT/s 1600

UCS-CPU-E5-2440 E5-2440 2.40 95 15 6 7.2 GT/s 1333

UCS-CPU-E5-2430L E5-2430L 2.00 60 15 6 6.4 GT/s 1333

UCS-CPU-E5-2420 E5-2420 1.90 95 15 6 7.2 GT/s 1333

UCS-CPU-E5-2403 E5-2403 1.80 80 10 4 6.4 GT/s 1066

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

Supported Configurations

(1) 1-CPU Configuration

■ Choose one CPU from any one of the rows of Table 3 on page 9.

(2) Two-CPU Configuration

■ Choose two identical CPUs from any one of the rows of Table 3 on page 9.

Caveats

■ For optimal performance, select DIMMs with the highest clock speed for a given processor.

■ The B22 M3 configured with 1 CPU provides limited network connectivity options. The

following restrictions apply:

— A virtual interface card (VIC), the VIC 1240, must always be installed in the VIC 1240

connector.

— The connectivity options are:

• VIC 1240 installed in VIC 1240 slot (adapter 1 slot) and no adapter installed in the

mezzanine slot (adapter 2 slot)

■ See Network Connectivity on page 41 for complete information on network connectivity

support for a B22 M3 configured with 1 CPU or 2 CPUs.

■ The VIC 1240 adapter is supported for 1- or 2-CPU configurations.

■ Cisco, Emulex, or QLogic I/O adapters or Cisco UCS Storage Accelerators are supported only

for 2-CPU configurations.

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

STEP 3 CHOOSE MEMORY

The standard memory features are:

■ DIMMs

— Clock speed: 1600 MHz

— Ranks per DIMM: 1 or 2

— Operational voltage: dual (1.5 or 1.35 V)

—Registered

■ DDR3 ECC registered DIMMs (RDIMMs)

■ Memory is organized with three memory channels per CPU, with up to two DIMMs per

channel (DPC), as shown in

Figure 3. Maximum memory capacity is 384 GB (with 32 GB

DIMMs).

Figure 3 UCS B22 M3 Memory Organization

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

Choose DIMMs and Memory Mirroring

Select the memory configuration and whether or not you want the memory mirroring option.

The supported memory DIMMs and the mirroring option are listed in

Table 4.

The supported memory DIMMs in the UCS B22 M3 are listed in Table 4.

NOTE: When memory mirroring is enabled, the memory subsystem simultaneously

writes identical data to two adjacent channels. If a memory read from one of the

channels returns incorrect data due to an uncorrectable memory error, the system

automatically retrieves the data from the other channel. A transient or soft error in

one channel does not affect the mirrored data, and operation continues unless there

is a simultaneous error in exactly the same location on a DIMM and its mirrored

DIMM. Memory mirroring reduces the amount of memory available to the operating

system by 50% because only one of the two populated channels provides data.

Table 4 Supported DDR3 DIMMs and Memory Mirroring Option

Product ID (PID) PID Description Voltage

Ranks

/DIMM

DIMM Options

UCS-ML-1X324RY-A 32GB DDR3-1600-MHz LRDIMM/PC3-12800/4R/x4/1.35v/35nm 1.35 4

UCS-MR-1X162RY-A 16GB DDR3-1600-MHz RDIMM/PC3-12800/2R/x4/1.35v/35nm 1.35/1.5 V 2

UCS-MR-1X082RY-A 8GB DDR3-1600-MHz RDIMM/PC3-12800/2R/x4/1.35v/35nm 1.35/1.5 V 2

UCS-MR-1X041RY-A 4GB DDR3-1600-MHz RDIMM/PC3-12800/1R/x4/1.35v/35nm 1.35/1.5 V 1

Memory Mirroring Option

N01-MMIRROR Memory mirroring option

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

Supported Configurations

(1) Without memory mirroring:

■ Select from 1 to 6 DIMMs per CPU (note that there are 6 DIMM slots per CPU)

(2) With memory mirroring:

■ Select 2 or 4 DIMMs per CPU. The DIMMs must be identical across channels for the same

banks.The DIMMs will be placed by the factory as shown in

Table 5:

■ Select the memory mirroring option (N01-MMIRROR) as shown in Table 4 on page 12.

Caveats

■ For 2-CPU configurations, DIMMs must be even across the server (2, 4, 6 up to 12). For

example, you can select four 8 GB DIMMs and six 16 GB DIMMs.

■ Memory mirroring reduces the amount of available memory by 50% (quantity of DIMMs must

be even for mirroring).

■ By default, all DIMMs run at 1.35 V, which yields 1333-MHz memory speeds. To run the

memory DIMMS at 1600 MHz, you need to go into the BIOS or set the policy with UCSM

(service profile) to run in Performance Mode. This forces the DIMMs to operate at 1.5 V and

yields 1600-MHz speeds provided:

— The DIMMs are 1600-MHz devices

— The CPUs chosen support 1600-MHz operation

For more information regarding memory, see DIMM and CPU Layout on page 34 and

DIMM Population on page 36.

Table 5 DIMM Placement With Memory Mirroring

Number of

DIMMs per

CPU

DIMM Placement in Channels (with memory mirroring implemented).

Note that Channels B and F are not used for memory mirroring

CPU 1 CPU 2

2 1 DIMM in Channel C (C0),

1 DIMM in Channel D (D0)

1 DIMM in Channel G (G0),

1 DIMM in Channel H (H0)

4 2 DIMMs in Channel C (C0, C1),

2 DIMMs in Channel D (D0, D1)

2 DIMMs in Channel G (G0, G1),

2 DIMMs in Channel H (H0. H1)

NOTE: System performance is optimized when the DIMM type and quantity are equal

for both CPUs, and when all channels are filled equally across the CPUs in the server.

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

STEP 4 CHOOSE HARD DISK DRIVES or SOLID STATE DRIVES (OPTIONAL)

The UCS B22 M3 can be ordered with or without drives. The standard disk drive features are:

■ 2.5-inch small form factor

■ Hot-pluggable sled mounted

Choose Drives

The supported drives in the UCS B22 M3 are listed in Table 6.

NOTE: The UCS B22 M3 blade server meets the external storage target and switch

certifications as described in the following link:

http://www.cisco.com/en/US/docs/switches/datacenter/mds9000/interoperabilit

y/matrix/Matrix8.html#wp323852

Table 6 Supported Hot-Pluggable Sled-Mounted HDDs and SSDs

Product ID (PID) PID Description

Drive

Type

Capacity

HDDs

A03-D1TBSATA 1 TB 6 Gb SATA 7.2K RPM SFF HDD SATA 1 TB

UCS-HDD900GI2F106 900 GB 6Gb SAS 10K RPM SFF HDD SAS 900 GB

A03-D600GA2 600 GB 6 Gb SAS 10K RPM SFF HDD SAS 600 GB

A03-D500GC3 500 GB 6 Gb SATA 7.2K RPM SFF HDD SATA 500 GB

UCS-HDD300GI2F105 300 GB 6 Gb SAS 15K RPM SFF HDD SAS 300 GB

A03-D300GA2 300 GB 6 Gb SAS 10K RPM SFF HDD SAS 300 GB

SSDs

UCS-SD400G0KA2-G 400GB SATA 2.5" Enterprise Value SSD SATA 400 GB

UCS-SD120GOKS2-EV 120 GB SATA 2.5 inch Enterprise Value 6G SSD SATA 120 GB

UCS-SD100G0KA2-G 100GB SATA 2.5" Enterprise Value SSD SATA 100 GB

NOTE: The integrated LSI 2002 MegaRAID controller supports hard disk drives (HDDs)

or solid state drives (SSDs). Write cache is not implemented. SSDs are recommended

for applications requiring high-speed local storage, which is an order of magnitude

faster than HDDs.

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

Supported Configurations

(1) 1-Drive System

■ Select one of the drives listed in Table 6.

(1) 2-Drive System

■ Select two identical drives from Table 6. There is no support for mixing of drive types or

capacities.

Caveats

■ If you select two drives, they must be identical in type and capacity.

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

STEP 5 CHOOSE ADAPTERS

The adapter offerings are:

■ Cisco Adapters: Virtual Interface Cards (VICs)

Cisco developed Virtual Interface Cards (VICs) to provide flexibility to create multiple NIC and

HBA devices. The VICs also support adapter Fabric Extender and Virtual Machine Fabric Extender

technologies.

■ Converged Network Adapters (CNAs)

Emulex and QLogic Converged Network Adapters (CNAs) consolidate Ethernet and Storage (FC)

traffic on the Unified Fabric by supporting FCoE.

■ Cisco UCS Storage Accelerators

These Storage Accelerator adapters are designed specifically for the Cisco UCS B-series M3

blades servers and integrate seamlessly to allow improvement in performance and relief of I/O

bottlenecks.

NOTE: There are two slots on the server. Adapter slot 2 accommodates Em ulex or

QLogic I/O adapters or Cisco UCS Storage Accelerators, and adapter slot 1 is a

dedicated slot for the VIC 1240 adapter only.

Table 7 shows which adapters plug into

each of the two slots. Only the VIC 1240 adapter plugs into the VIC 1240 adapter 1

slot. All other adapters plug into the adapter 2 slot.

NOTE: You must have a B22 M3 configured with 2 CPUs to support adapters that plug

into the adapter 2 connector. The VIC 1240 adapter is supported on both 1- and

2-CPU configured systems.

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

Choose a Mezzanine Adapter

The supported mezzanine adapters in the UCS B22 M3 are listed in Table 7.

“Adapter 1” and “Adapter 2” refer to the UCS Manager (UCSM) naming convention for the

adapter slots (this document uses the UCSM naming convention). In the server BIOS and on the

motherboard, the corresponding slots are labeled as “mLOM” and “Mezz 1,” respectively. See

Table 8.

Table 7 Supported Mezzanine Adapters

Product ID (PID) PID Description Connector

Virtual Interface Cards (VICs)

UCSB-MLOM-40G-01 Cisco UCS VIC 1240 modular LOM for M3 blade servers. Plugs into

adapter slot 1 only. It is the only adapter that can be plugged into

the adapter 1 connector.

Adapter 1

UCS-VIC-M82-8P Cisco UCS VIC 1280 dual 40 Gb capable Virtual Interface Card Adapter 2

Converged Network Adapters (CNAs)

UCSB-MEZ-QLG-03 Cisco UCS CNA M73KR-Q QLogic Adapter Adapter 2

UCSB-MEZ-ELX-03 Cisco UCS CNA M73KR-E Emulex Adapter Adapter 2

Cisco UCS Storage Accelerators

Notes

1. Do not mix Fusion io storage accelerator families. That is, do not mix “MP” or “MS” (ioMemory3) with “M”

(ioDrive2) family cards.

UCSB-F-FIO-1600MS UCS 1600 GB Fusion ioMemory3 SX Scale line for B-Series Adapter 2

UCSB-F-FIO-1300MP UCS 1300 GB Fusion ioMemory3 PX Performance line for B-Series Adapter 2

UCSB-F-FIO-785M Cisco UCS 785 GB MLC Fusion ioDrive2 Adapter 2

UCSB-F-FIO-365M Cisco UCS 365 GB MLC Fusion-io ioDrive2 Adapter 2

UCSB-F-LSI-400S LSI 400 GB SLC WarpDrive Adapter 2

Table 8 Adapter Slot Naming

Server BIOS and Motherboard Slot Naming UCSM Slot Naming

mLOM (VIC 1240 only) Adapter 1

Mezz1 Adapter 2

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

Supported Configurations

(1) B22 M3 Configured with 1 CPU

For a B22 M3 configured with 1 CPU, the supported configurations are listed in Table 9. Choose

one configuration.

(2) B22 M3 Configured with 2 CPUs

For a B22 M3 configured with 2 CPUs, the supported configurations are listed in Table 10.

Choose one configuration.

Table 9 Supported Adapter

Combinations Options (1-CPU Configuration)

Notes

1. In the server BIOS and on the motherboard, “Adapter 1” and “Adapter 2” are labeled as “mLOM” and “Mezz 1,”

respectively

Fabric

Extender

Compatibility

Adapter Slot 1 Adapter Slot 2 Ports Reference

2208XP (PIDs UCS-IOM-2208XP, UCS-IOM2208-16FET)

2208XP VIC 1240 None 4 x 10 Gb Figure 11 on page 44

2204XP (PIDs UCS-IOM-2204XP, UCS-IOM2204-8FET)

2204XP VIC 1240 None 2 x 10 Gb Figure 12 on page 45

2104XP (PID N20-I6584)

2104XP VIC 1240 None 2 x 10 Gb Figure 13 on page 45

Table 10 Supported Adapter

Combinations Options (2-CPU Configuration)

Fabric

Extender

Compatibility

Adapter Slot 1 Adapter Slot 2 Ports Reference

2208XP (PIDs UCS-IOM-2208XP, UCS-IOM2208-16FET)

2208XP None

Emulex or QLogic I/O adapter

2 x 10 Gb Figure 14 on page 46

2208XP VIC 1240 None 4 x 10 Gb Figure 15 on page 47

2208XP VIC 1240 Cisco UCS Storage Accelerator 4 x 10 Gb Figure 16 on page 47

2208XP VIC 1240

Emulex or QLogic I/O adapter

6 x 10 Gb Figure 17 on page 48

2208XP VIC 1240 VIC 1280 8 x 10 Gb Figure 18 on page 48

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

Also see Network Connectivity on page 41 for more information.

To help ensure that your operating system is compatible with the adapters you have selected,

please check the Hardware Compatibility List at this URL:

http://www.cisco.com/en/US/products/ps10477/prod_technical_reference_list.html

Caveats

■ If a VIC 1240 adapter is not installed (2-CPU configuration only), you must choose a Cisco,

Emulex, or QLogic I/O adapter to be installed in adapter 2 slot (see also

Network

Connectivity on page 41)

■ The mezzanine adapters are not supported for 1-CPU configurations. You must have two

CPUs installed before you can install and use mezzanine adapters.

■ The 1-CPU server configuration must always have a VIC 1240 installed in the adapter 1 slot.

2204XP (PIDs UCS-IOM-2204XP, UCS-IOM2204-8FET)

2204XP None

Emulex or QLogic I/O adapter

2 x 10 Gb Figure 19 on page 49

2204XP VIC 1240 None 2 x 10 Gb Figure 20 on page 50

2204 XP VIC 1240 Cisco UCS Storage Accelerator 2 x 10 Gb Figure 21 on page 50

2204XP VIC 1240

Emulex or QLogic I/O adapter

4 x 10 Gb Figure 22 on page 51

2204XP VIC 1240

VIC 1280

4 x 10 Gb Figure 23 on page 51

2104XP (PID N20-I6584)

2104XP VIC 1240 None 2 x 10 Gb Figure 24 on page 52

2104XP VIC 1240 Cisco UCS Storage Accelerator 2 x 10 Gb Figure 25 on page 52

Notes

1. In the server BIOS and on the motherboard, “Adapter 1” and “Adapter 2” are labeled as “mLOM” and “Mezz 1,”

respectively

2. Specifically, the UCSB-MEZ-QLG-03 (QLogic) or UCSB-MEZ-ELX-03 (Emulex) adapter

Table 10 Supported Adapter

Combinations Options (2-CPU Configuration) (continued)

Fabric

Extender

Compatibility

Adapter Slot 1 Adapter Slot 2 Ports Reference

Cisco UCS B22 M3 Blade Server

CONFIGURING the SERVER

STEP 6 ORDER A TRUSTED PLATFORM MODULE

Trusted Platform Module (TPM) is a computer chip (microcontroller) that can securely store

artifacts used to authenticate the platform (server). These artifacts can include passwords,

certificates, or encryption keys. A TPM can also be used to store platform measurements that

help ensure that the platform remains trustworthy. Authentication (ensuring that the platform

can prove that it is what it claims to be) and attestation (a process helping to prove that a

platform is trustworthy and has not been breached) are necessary steps to ensure safer

computing in all environments.

The TPM ordering information is listed in Table 11.

Table 11 Trusted Platform Module

Product ID (PID) PID Description

UCSX-TPM1-001 Truste d P latfo r m M o dul e f o r U CS

NOTE: The module used in this server conforms to TPM v1.2/1.3, as defined by the

Trusted Computing Group (TCG). It is also SPI-based.

Page is loading ...

Cisco UCS-CPU-E52403B= Datasheet

Brand: Cisco

Model: UCS-CPU-E52403B=

Category: Processors

Type: Datasheet

Download PDF

report

Cisco UCS-CPU-E52403B= Datasheet

Cisco UCS-CPU-E52403B= Datasheet

Related papers

Other documents