SOYO SY-6IZM User manual

Brand: SOYO

Model: SY-6IZM

Category: Motherboards

Type: User manual

This manual is also suitable for

SY-6IZM/3

SY-6IZM/3

Motherboard

***************************************************

Pentium

III, Pentium

II & Celeron

processors supported

82440 ZX AGP/PCI Motherboard

3D Audio & AGP built-in

66 & 100 MHz Front Side Bus supported

Micro-ATX Form Factor

***************************************************

User's Guide

Technical Reference

Table of Contents SY-6IZM/3

iii

Table of Contents

SY-6IZM/3 MOTHERBOARD LAYOUT....................................................1

CHAPTER 1 INTRODUCTION .............................................................2

1-1 KEY FEATURES..............................................................2

1-2 HANDLING THE MOTHERBOARD ..................................5

1-3 ELECTROSTATIC DISCHARGE PRECAUTIONS.............5

CHAPTER 2 HARDWARE SETUP .......................................................6

2-1 PREPARATIONS .............................................................6

2-2 UNPACKING THE MOTHERBOARD................................7

2-3 INSTALLATION GUIDE....................................................8

CHAPTER 3 BIOS SETUP UTILITY...................................................32

3-1 SOYO COMBO SETUP..................................................34

3-2 STANDARD CMOS SETUP............................................39

3-3 BIOS FEATURES SETUP..............................................42

3-4 CHIPSET FEATURES SETUP........................................47

3-5 POWER MANAGEMENT SETUP...................................50

3-6 PNP/PCI CONFIGURATION SETUP..............................54

3-7 LOAD SETUP DEFAULTS..............................................57

3-8 INTEGRATED PERIPHERALS.......................................58

3-9 SUPERVISOR PASSWORD...........................................62

3-10 USER PASSWORD........................................................64

3-11 IDE HDD AUTO DETECTION.........................................65

CHAPTER 4 3D PNP AUDIO ONBOARD...........................................66

4-1 ONBOARD JOYSTICK PORT ........................................66

4-2 ONBOARD AUDIO.........................................................66

CHAPTER 5 DRIVERS INSTALLATION.............................................69

Motherboard Layout SY-6IZM/3

SY-6IZM/3 MOTHERBOARD LAYOUT

Back Panel SY-6IZM/3 Platform

COM 1

VGA

PRT

USB 1

USB 2

PS/2 KB

Connector

PS/2 Mouse

Connector

PCI Slot #1

PCI Slot #2

PCI Slot #3

Intel

82371EB

IR1

CPUFAN

COM2

FDC

ISA Slot #1

ATX

Power

JP1

CHAFAN

Flash BIOS

YMF740-V

YAMAHA

W83977EF

-AW

Winbond

Game Port

LINE-OUT

LINE-IN

MIC JACK

W83781D

8 2 8 A C

Hardware

Monitoring

WOL

Header

JP44

Speaker

Keylock

Power

LED

Reset

PWRBT

Turbo

LED

HDD LED

Winbond

W83782M

JP5

CMOS Clear

Jumper

JP8

JP3

ATI

RAGE Pro

Lithium

Battery

IDE 2

IDE 1

DIMM 1

DIMM 2

DIMM 3

Slot 1

Intel

82443 ZX

AC97

Codec

JP7

JP10

Introduction SY-6IZM/3

Chapter 1

INTRODUCTION

The SY-6IZM/3 AGP/PCI Motherboard is a high-performance Slot 1

processor supported Micro-ATX form-factor system board. SY-

6IZM/3 uses the 82440 ZX Chipset technology and supports Slot 1

processors. This Motherboard is fully compatible with industry

standards and adds many technical enhancements.

1-1 KEY FEATURES

Supports Intel Pentium

III processor (450-550MHz), Pentium

processor (233-450MHz) & Celeron

processor (266-433MHz)

Easy CPU settings in BIOS with the “SOYO COMBO Setup”.

3D YAMAHA YMF740 Audio

ATI Rage Pro Graphics with 8MB Video memory on board

Auto-detect CPU voltage

PC98, APM, ACPI, Ultra DMA/33

Power-on by modem or alarm

Supports Wake-On-LAN (WOL)

Supports Power-On by PS/2 Keyboard

3 x 32-bit bus mastering PCI slots

1 x 16-bit ISA slot

2 x USB ports

1 x IrDA port

Supports multiple-boot function

ATX power connector

Power failure resume

Introduction SY-6IZM/3

SY-6IZM/3 PLATFORM FEATURES

Board Size 4-layer PCB, 24.4x22.0cm (9.6” x 8.7 ”), Micro-ATX

Form Factor

Slot1 Slot 1 for Pentium

III, Pentium

II & Celeron

Processor

Ø Supports the following processors

u 100MHz FSB

Pentium

II 350/400/450 MHz

Pentium

III 450/500/550 MHz

u 66MHz FSB

Pentium

II 233/266/300/333 MHz

Celeron 300A/333/366/400/433 MHz

Celeron 266/300 MHz

Ø Supports both boxed and non-boxed type of CPUs

Ø Includes a CPU mount kit with retention clip

Ø Features Auto-detection of CPU voltage

Chipset 82440 ZX AGP/PCI Set

Audio Onboard YAMAHA YMF740 Onboard

AGP Onboard ATI RAGE PRO

ATX Power 20-pin Male Connector

CPUFAN 3-pin CPU Cooling Fan Connector

Memory DIMM Bank (DIMM1~3)

Ø Three strips of 168-pin Unbuffered SDRAM DIMM

Ø Supports 8/16/32/64/128MB DIMM modules in each

bank

Ø Provides up to 256 MBytes of main memory

BIOS System BIOS built-in, Award BIOS

Ø APM, ACPI and "Plug-and-Play" function

Ø Supports multiple-boot function

Ø Onboard FLASH memory for easy upgrade

Ø Y2K Compliant

Bus Controller Compliant with version 2.1 PCI specifications

PCI Slots 3 x 32-bit Bus Mastering Slots

ISA Slots 1 x 16-bit ISA Slots

Introduction SY-6IZM/3

IDE1, IDE2 2 x 40-pin Bus Mastering E-IDE/ATAPI Ports

Ø IDE1: Primary IDE Device Connector

Ø IDE2: Secondary IDE Device Connector

Ø Supports Ultra DMA/33

COM2 1 x 9-pin RS-232 Serial Connector

FDC 1 Floppy Disk Drive (FDD) Port

(Supports 1.2MB/1.44MB/2.88MB and LS120/3-mode FDD)

IR1 5-pin Serial Infrared Device Header

Keylock 5-pin KeyLock Header

Reset 2-pin Reset Switch Header

Speaker 4-pin PC Speaker Header

TB_LED 2-pin Turbo LED Header

HDD_LED 2-pin IDE Device LED Header

PWRBT ATX Power On/Off Switch 2-pin Header

J4, J5 2 x CD Line-in 4-pin Headers

JP1 Power-On by PS/2 Keyboard Jumper

JP3 AGP operating speed Select Jumper

JP5 CMOS Clear Jumper

JP8 Power Button Enable Jumper

JP10 External Suspend Button Header

JP44 WOL (Wake-On-LAN) 3-pin Header

SY-6IZM/3 BACK-PANEL FEATURES

PRT 1 x Onboard 25-pin Female Parallel Printer Port

COM1 1 x Onboard RS-232 Serial Port

PS/2 KB 1 x Onboard PS/2 Keyboard Connector

PS/2 Mouse 1 x Onboard PS/2 Mouse Connector

USB1, USB2 2 x Onboard USB

(Universal Serial Bus)

Connectors

VGA 1 x Onboard 15-pin VGA Port

JOYSTICK 1 x Onboard 15-pin Joystick Port

LINE-OUT 1 x Onboard Line-out Audio Stereo Jack

LINE-IN 1 x Onboard Line-in Audio Stereo Jack

MIC JACK 1 x Onboard Microphone Stereo Jack

Introduction SY-6IZM/3

1-2 HANDLING THE MOTHERBOARD

To avoid damage to your Motherboard, follow these simple rules

while unpacking:

Ø Before handling the Motherboard, ground yourself by grasping

an unpainted portion of the system's metal chassis.

Ø Remove the Motherboard from its anti-static packaging. Hold

the Motherboard by the edges and avoid touching its

components.

Ø Check the Motherboard for damage. If any chip appears loose,

press carefully to seat it firmly in its socket.

Warning: Do not apply power if the Motherboard appears

damaged. If there is damage to the board, contact your

dealer immediately.

1-3 ELECTROSTATIC DISCHARGE PRECAUTIONS

Make sure to ground yourself before handling the Motherboard or

other system components. Electrostatic discharge can easily

damage the components. Note that you must take special

precautions when handling the Motherboard in dry or air-conditioned

environment.

To protect your equipment from electrostatic discharge, take the

following precautions:

Ø Do not remove the anti-static packaging until you are ready to

install.

Ø Ground yourself before removing any system component from

its protective anti-static packaging. (To ground yourself, grasp

the expansion slot covers or other unpainted portions of the

computer chassis.)

Ø Frequently ground yourself while working or use a grounding

strap.

Ø Handle the Motherboard by its edges and avoid touching its

components.

Hardware Setup SY-6IZM/3

Chapter 2

HARDWARE SETUP

Congratulations on your purchase of SY-6IZM/3 Motherboard. You

are about to install and connect your new Motherboard.

Note: Do not unpack the Motherboard from its protective anti-

static packaging until you have made the following preparations.

2-1 PREPARATIONS

Gather and prepare all the following hardware equipment to

complete the installation successfully:

1. Slot 1 processor with built-in CPU cooling fan (boxed type).

Note: This Motherboard supports non-boxed type CPUs. The

heavier CPU cooling fan requires the installation of a CPU

support stand.

2. DIMM memory module

3. Computer case and chassis with adequate power supply unit

4. Monitor

5. Keyboard

6. Pointing Device (PS/2 mouse)

7. Speaker(s) (optional)

8. Disk Drives: HDD, CD-ROM, Floppy drive…

9. External Peripherals: Printer, Plotter, and Modem (optional)

10. Internal Peripherals: Modem and LAN cards (optional)

Frequently Asked Questions:

l Do I need to install a VGA card?

l Do I also need to install a sound card?

The answer is NO to both questions above, since, for your

convenience, the SY-6IZM/3 Motherboard already features one

built-in VGA port and three built-in audio-stereo ports (Line-out,

Line-in, Microphone).

l What kind of speaker can connect to "Line-out" port?

This Motherboard requires a speaker with built-in amplifier to

generate proper output sound volume.

Hardware Setup SY-6IZM/3

2-2 UNPACKING THE MOTHERBOARD

When unpacking the Motherboard, check for the following items:

Ø The SY-6IZM/3 82440 ZX AGP/PCI Motherboard

Ø The Quick Start Guide *

Ø The Installation CD-ROM *

Ø One IDE Device Flat Cable

Ø One Floppy Disk Drive Flat Cable

Ø Serial port flat cable with a 9-pin connector bracket

* If your board comes with a driver disc and a paper manual, the Quick Start Guide

and the CD-ROM are not included in the package.

Warning: Do not unpack the Motherboard from its anti-

static packaging until you are ready to install it.

Like most electronic equipment, your Motherboard may be damaged

by electrostatic discharge. To avoid permanent damage to

components ground yourself while working by using a grounding

strap. Otherwise, ground yourself frequently by touching the

unpainted portion of the computer chassis to drain the static

charges.

Handle the Motherboard carefully, holding it by the edges.

You are now ready to start the installation.

Hardware Setup SY-6IZM/3

2-3 INSTALLATION GUIDE

We will now begin the installation of the Motherboard. Please follow

the step-by-step procedure designed to lead you to a complete and

correct installation.

Warning: Turn off the power to the Motherboard, system chassis,

and peripheral devices before performing any work on the

Motherboard or system.

BEGIN THE INSTALLATION

Step 1. CPU Installation

Your SY-6IZM/3 Motherboard comes with a CPU retention set kit.

The retention set is used to hold the processor attached to the Slot 1

CPU connector on the Motherboard.

Follow these instructions to install your Slot 1 processor correctly.

Ø Retention Module

Hardware Setup SY-6IZM/3

1. Open the two sides by folding them up.

2. Push the locks on top of the CPU inward.

Hardware Setup SY-6IZM/3

3. Insert the CPU into the retention module. The CPU fits in the

CPU slot in only ONE way, do not try to force it in.

4. After completely inserting the CPU, push the two locks on top

of the CPU outward. Now your CPU is ready for use.

To remove the CPU, press the two notches on top of the CPU

inward. Now press the two slides on the retention module down

and remove the CPU.

Hardware Setup SY-6IZM/3

Note: Installing a heat sink and cooling fan on top of your

CPU is necessary for proper heat dissipation. Failing to

install these items may result in overheating and possible

burn-out of your CPU.

Step 2. CPU Fan Installation

Your Slot 1 processor kit comes with a cooling fan. Mount the fan on

the processor according to the instructions provided by the

manufacturer. The fan is a key component that will ensure system

stability. The fan prevents overheating, therefore prolonging the life

of your CPU.

Note: Remember to connect the fan to the appropriate power

source.

Hardware Setup SY-6IZM/3

Step 3. SDRAM Memory Module Installation

This Motherboard features 3 x DIMM Banks for 168-pin 3.3V

unbuffered DIMM modules.

DIMM 3

DIMM 1

DIMM 2

W83781D

Hardware Setup SY-6IZM/3

This Motherboard features 3 x DIMM for 168-pin 3.3V unbuffered

DIMM modules, providing support for up to 256MB of main memory

using DIMM modules from 8MB to 128MB.

Number of

Memory Modules

DIMM 1 DIMM 2 DIMM 3

Double-sided

/Single-sided

Double-sided

/Single-sided

Double-sided

/Single-sided

Single-sided Single-sided

RAM Type

SDRAM

Memory Module

Size (MB)

8/16/32/64/128 Mbytes

Note: Because DIMM 2 and 3 are shared, double-sided DIMMs can be

used in only one of the DIMMs. With single-sided DIMMs both 2 and 3

can be used.

Step 4. IDE Device Installation (HDD, CD-ROM)

This Motherboard offers two primary and secondary IDE device

connectors (IDE1, IDE2.) It can support up to four high-speed HDD

or CD-ROM.

Connect one side of the 40-pin flat cable to the IDE device (HDD or

CD-ROM) and plug the other end to the primary (IDE1) or secondary

(IDE2) directionally keyed IDE connector on the Motherboard.

This Motherboard can support up to four HDDs.

Hardware Setup SY-6IZM/3

Step 5. Floppy Drive Installation

The system supports 5 possible floppy drive types: 720 KB, 1.2 MB,

1.44 MB, 2.88 MB, and LS-120. In addition, this Motherboard

supports a 3-mode (720KB/1.2MB/1.44MB) floppy commonly used

in Japan.

Connect one side of the 34-pin flat cable to the floppy drive and plug

the other end to the floppy drive connector on the Motherboard.

This Motherboard can support up to 2 floppy drives.

Hardware Setup SY-6IZM/3

Step 6. Front Panel Connections

Plug the computer case's front panel devices to the corresponding

headers on the Motherboard.

1. Power LED & KeyLock

Plug the Power LED cable into the 5-pin Keylock header.

Some systems may feature a KeyLock function with a front panel

switch for enabling or disabling the keyboard. Connect the KeyLock

switch to the 5-pin Keylock header on the Motherboard.

Please install according to the following pin assignment: pin 1,3 are

for Power LED and pin 4,5 are for Keylock.

2. Reset

Plug the Reset push-button cable into the 2-pin Reset header on the

Motherboard. Pushing the Reset button on the front panel will cause

the system to restart the boot-up sequence.

W83781D

Reset

PWRBT

Speaker

Keylock

Power

LED

Turbo

LED

HDD LED

Hardware Setup SY-6IZM/3

3. Speaker

Attach the 4-pin PC speaker cable from the case to the Speaker

header on the Motherboard.

4. Turbo LED

Connecting the 2-pin Turbo LED cable to the corresponding Turbo

LED header will cause the LED to light whenever the system is in

Turbo mode.

The manufacturer has permanently set this Motherboard in Turbo

mode due to most hardware and software compliance to turbo

mode.

5. IDE LED

Attach the 2-pin IDE device LED cable to the corresponding IDE

LED header on the Motherboard. This will cause the LED to lighten

when an IDE (HDD, CD-ROM) device is active.

6. ATX Power On/Off Switch

Attach the 2-pin momentary type switch to the PWRBT header for

turning On or Off your ATX power supply.

Hardware Setup SY-6IZM/3

Step 7. Back Panel Connections

All external devices such as the keyboard, printer, PS/2 mouse,

modem, USB, monitor, joystick and audio devices (speakers/

headphones, microphone and CD/cassette player) can be plugged

directly onto the Motherboard back panel.

Only after you have fixed and locked the Motherboard to the

computer case can you start connecting the external peripheral

devices.

When connecting an external device, use the following figure to

locate and identify which back panel connector to plug the device to.

1. Onboard Serial Port COM1

External peripherals that use serial transmission scheme include:

- serial mouse,

- and modem.

W83781D

COM 1

VGA

PRT

USB 1

USB 2

PS/2 KB

Connector

PS/2 Mouse

Connector

Game Port

LINE-OUT

LINE-IN

MIC JACK

Page is loading ...

SOYO SY-6IZM User manual

Brand: SOYO

Model: SY-6IZM

Category: Motherboards

Type: User manual

This manual is also suitable for

SY-6IZM/3

Download PDF

report

SOYO SY-6IZM User manual

This manual is also suitable for

SOYO SY-6IZM User manual

Related papers

Other documents