SOYO SY-7IZB User manual

SY-7IZB

Motherboard

****************************************************

Socket 370 for Intel Celeron

TM

Processor

Intel 440 ZX AGP/PCI Motherboard

66 &100MHz Front Side Bus supported

Baby AT Form Factor

****************************************************

User's Guide

&

Technical Reference

SOYO™ SY-7IZB

ii

About This Guide

This User's Guide is for assisting system manufacturers and end users in setting up

and installing the Motherboard. Information in this guide has been carefully checked

for reliability; however, no guarantee is given as to the correctness of the contents.

The information in this document is subject to change without notice.

Copyright Notice

by Soyo Computer Inc. You may not reproduce, transmit, transcribe, store in a

retrieval system, or translate into any language, in any form or by any means,

electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of

this publication without express written permission of Soyo Computer Inc.

Trademarks

Soyo is a registered trademark of Soyo Computer Inc. All trademarks are the property

of their owners.

Disclaimer

Soyo Computer Inc. makes no representations or warranties regarding the contents

of this manual. We reserve the right to revise the manual or make changes in the

specifications of the product described within it at any time without notice and without

obligation to notify any person of such revision or change. The information contained

in this manual is provided for general use by our customers. Our customers should be

aware that the personal computer field is the subject of many patents. Our customers

should ensure that their use of our products does not infringe upon any patents. It is

the policy of Soyo Computer Inc. to respect the valid patent rights of third parties and

not to infringe upon or assist others to infringe upon such rights.

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to restrictions set forth in

subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause

at 252.277-7013.

Product Rights

Products mentioned in this manual are mentioned for identification purpose only.

Product names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies.

If you need any further information, please come to our home page on the Internet.

The address is "http://www.soyo.com.tw".

Edition: February 1999

Version 1.0

7IZB SERIAL

FC

C

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

POST CONSUMER

RECYCLED PAPER

100%

Table of Contents SY-7IZB

iii

Table of Contents

SY-7IZB MOTHERBOARD LAYOUT.............................................1

CHAPTER 1 INTRODUCTION .....................................................2

1-1 KEY FEATURES......................................................2

1-2 HANDLING THE MOTHERBOARD..........................5

1-3 ELECTROSTATIC DISCHARGE PRECAUTIONS....5

CHAPTER 2 HARDWARE SETUP...............................................6

2-1 PREPARATIONS .....................................................6

2-2 UNPACKING THE MOTHERBOARD .......................7

2-3 INSTALLATION GUIDE............................................8

CHAPTER 3 BIOS SETUP UTILITY...........................................27

3-1 SOYO COMBO SETUP .........................................29

3-2 STANDARD CMOS SETUP ...................................34

3-3 BIOS FEATURES SETUP......................................37

3-4 CHIPSET FEATURES SETUP...............................41

3-5 POWER MANAGEMENT SETUP...........................44

3-6 PNP/PCI CONFIGURATION SETUP......................48

3-7 LOAD SETUP DEFAULTS .....................................51

3-8 INTEGRATED PERIPHERALS...............................52

3-9 SUPERVISOR PASSWORD ..................................56

3-10 USER PASSWORD ...............................................58

3-11 IDE HDD AUTO DETECTION................................59

CHAPTER 4 DRIVERS INSTALLATION......................................60

Motherboard Features SY-7IZB

1

SY-7IZB MOTHERBOARD LAYOUT

SY-7IZB Platform

Flash BIOS

IR1

5

1

AGP Slot

PRT 1

KB

Connector

PS/2 Mouse

Connector

ATX Power

AT Power

1

COM 2

1

FDC

1

IDE 1

1

IDE 2

1

3V

Lithium

Battery

COM 1

1

Intel

82440ZX

JP44

1

3

Winbond

83977

CHAFAN

PCI Slot #2

PCI Slot #1

PCI Slot #3

PCI Slot #4

2

1

10

USB1

*

Socket 370

2

DIMM 2

DIMM 1

DIMM 3

2

Speaker

Keylock

Power

LED

_

_ _

+

RST

PWR

ACPI

LED

HDD

LED

Intel

371EB

ISA Slot #1

1

3

JP10

CPU FAN

1

JP5

1

3

(PC-PCI)

SB-LINK

TM

Winbond

W83782M

Hardware

Monitoring

1

3

JP9

Introduction SY-7IZB

2

Chapter 1

INTRODUCTION

The SY-7IZB AGP/PCI Motherboard is a high-performance

Celeron

®

processor supported ATX form-factor system board. SY-

7IZB uses the 440 ZX Chipset technology and supports Socket 370

Celeron

TM

class processors. This Motherboard is fully compatible

with industry standards and adds many technical enhancements.

1-1 KEY FEATURES

Ø Supports Intel Socket 370 Celeron

TM

processor (300A~500

MHz)

Ø Auto-detect CPU voltage

Ø PC98, ACPI, Ultra DMA/33

Ø SOYO COMBO Setup

Ø Supports system memory up to 256 MBytes

Ø Power-on by modem or alarm

Ø Supports power-on/off by keyboard

Ø Supports onboard hardware monitoring

and includes Hardware Doctor™ utility

Ø Supports Creative SB-LINK™ (PC-PCI) for PCI audio

Ø 1 x 32-bit AGP slot

Ø 4 x 32-bit bus mastering PCI slots

Ø 1 x 16-bit ISA slot

Ø 2 x USB ports onboard

Ø 1 x IrDA port

Ø Supports multiple-boot function

Ø AT & ATX power connectors

Introduction SY-7IZB

3

SY-7IZB PLATFORM FEATURES

Board Size 4-layer PCB, 21.5 x 22cm(”8.5x8.7”),

Baby-AT Form Factor

Socket 370 66/100MHz FSB

Ø Celeron Processor

300A/333/366/400/433/466/500

Ø Built-in full speed 128KB L2 cache.

Ø Features Auto-detection of CPU voltage

Chipset 440 ZX AGP Set

ATX Power 20-pin Male Connector

AT Power 12-pin Male connector

CPUFAN 3-pin CPU Cooling Fan Connector

CHAFAN 3-pin Case Cooling Fan Connector

Memory DIMM Bank (DIMM1~3)

Ø Three strips of 168-pin Unbuffered SDRAM DIMM

Ø Supports 8/16/32/64/128MB DIMM modules in each

bank

Ø Supports up to 256 MBytes of main memory

BIOS System BIOS built-in, Award BIOS

Ø APM, ACPI and "Plug-and-Play" function

Ø Supports multiple-boot function

Ø Onboard FLASH memory for easy upgrade

Ø Y2000 Compliant

Bus Controller Compliant with PCI specifications version 2.1

PCI Slots 4 x 32-bit Bus Mastering Slots

AGP Slot 1 x 32-bit AGP Slot

ISA Slots 1 x 16-bit ISA Slots

IDE1, IDE2 2 x 40-pin Bus Mastering E-IDE/ATAPI Ports

Ø IDE1: Primary IDE Device Connector

Ø IDE2: Secondary IDE Device Connector

Ø Supports Ultra DMA/33

FDC 1 Floppy Disk Drive (FDD) Port

(Supports 1.2MB/1.44MB/2.88MB and LS120/3-mode FDD)

IR1 5-pin Serial Infrared Device Header

Keylock 5-pin KeyLock Header

Introduction SY-7IZB

4

Reset 2-pin Reset Switch Header

Speaker 4-pin PC Speaker Header

TB_LED 2-pin ACPI LED Header

HDD_LED 2-pin IDE Device LED Header

PWRBT ATX Power On/Off Switch 2-pin Header

JP5 CMOS Clear Jumper

JP9 AGP operating speed Select Jumper

JP10 Power-On by Keyboard Jumper

JP44 WOL (Wake-On-LAN) 3-pin Header

PRT 25-pin Female external Parallel connector

Ø ECP/EPP/SPP multi-mode parallel printer port

COM1, COM2 10-pin Serial Ports

Ø Feature 2 x high-speed UARTs (with 16550 FIFO)

AT Keyboard 5-pin female AT Keyboard connector

PS/2 Mouse 6-pin male PS/2 mouse connector

USB1,USB2 Dual-row 10-pin header

*These processors are not available yet for testing.

Introduction SY-7IZB

5

HANDLING THE MOTHERBOARD

To avoid damage to your Motherboard, follow these simple rules

while unpacking:

Ø Before handling the Motherboard, ground yourself by grasping

an unpainted portion of the system's metal chassis.

Ø Remove the Motherboard from its anti-static packaging. Hold

the Motherboard by the edges and avoid touching its

components.

Ø Check the Motherboard for damage. If any chip appears loose,

press carefully to seat it firmly in its socket.

Warning: Do not apply power if the Motherboard appears

damaged. If there is damage to the board, contact your

dealer immediately.

1-2 ELECTROSTATIC DISCHARGE PRECAUTIONS

Make sure to ground yourself before handling the Motherboard or

other system components. Electrostatic discharge can easily

damage the components. Note that you must take special

precautions when handling the Motherboard in dry or air-conditioned

environment.

To protect your equipment from electrostatic discharge, take the

following precautions:

Ø Do not remove the anti-static packaging until you are ready to

install.

Ø Ground yourself before removing any system component from its

protective anti-static packaging. (To ground yourself, grasp the

expansion slot covers or other unpainted portions of the computer

chassis.)

Ø Frequently ground yourself while working or use a grounding strap.

Ø Handle the Motherboard by its edges and avoid touching its

components.

Hardware Setup SY-7IZB

6

Chapter 2

HARDWARE SETUP

Congratulations on your purchase of SY-7IZB Motherboard. You are

about to install and connect your new Motherboard.

Note: Do not unpack the Motherboard from its protective

anti-static packaging until you have made the following

preparations.

2-1 PREPARATIONS

Gather and prepare all the following hardware equipment to

complete the installation successfully:

1. Celeron

TM

processor with built-in CPU cooling fan (boxed

type).

Note: This Motherboard supports non-boxed type CPUs. The

heavier CPU cooling fan requires the installation of a CPU

support stand included in this Motherboard package.

2. DIMM memory module

3. Computer case and chassis with adequate power supply unit

4. Monitor

5. Keyboard

6. Pointing Device (Serial or PS/2 mouse)

7. Speaker(s) (optional)

8. Disk Drives: HDD, CD-ROM, Floppy drive…

9. External Peripherals: Printer, Plotter, and Modem (optional)

10. Internal Peripherals: Modem and LAN cards (optional)

Hardware Setup SY-7IZB

7

2-2 UNPACKING THE MOTHERBOARD

When unpacking the Motherboard, check for the following items:

Ø The SY-7IZB 440 ZX AGP/PCI Motherboard

Ø This Quick Start Guide *

Ø The Installation CD-ROM *

Ø One IDE Device Flat Cable

Ø One Floppy Disk Drive Flat Cable

Ø One bracket with one 9-pin serial connector, attached with 9-

pin falt cable, and one 6-pin PS/2 mouse connector, attached

with 6-pin cable.

Ø One bracket with one 25-pin connector parallel connector

attached with 25-pin flat cable and one 9-pin serial connector

attached with 9-pin flat cable.

* If your board comes with a driver disc and a paper manual, the Quick Start Guide

and the CD-ROM are not included in the package.

Warning: Do not unpack the Motherboard from its anti-

static packaging until you are ready to install it.

Like most electronic equipment, your Motherboard may be damaged

by electrostatic discharge. To avoid permanent damage to

components ground yourself while working by using a grounding

strap. Otherwise, ground yourself frequently by touching the

unpainted portion of the computer chassis to drain the static

charges.

Handle the Motherboard carefully, holding it by the edges.

You are now ready to start the installation.

Hardware Setup SY-7IZB

8

2-3 INSTALLATION GUIDE

We will now begin the installation of the Motherboard. Please follow

the step-by-step procedure designed to lead you to a complete and

correct installation.

Warning: Turn off the power to the Motherboard, system

chassis, and peripheral devices before performing any

work on the Motherboard or system.

Step 1. CPU Installation

Follow these instructions to install your Celeron

TM

class processor

correctly.

Locate the CPU socket labeled Socket 370 on your Motherboard

and note the distinctive pinhole arrangement.

Note the corresponding pinhole arrangement on the processor.

Socket 370

Blunt Edge Blunt Edge

CPU

Hardware Setup SY-7IZB

9

Follow these steps to install the CPU in the Socket 370:

1. Lift the socket handle up to a vertical position.

2. Align the blunt edge of the CPU with the matching pinhole

distinctive edge on the socket.

3. Seat the processor in the socket completely and without forcing.

4. Then close the socket handle to secure the CPU in place.

Step 2. CPU Fan Installation

Your Celeron

TM

processor kit comes with a cooling fan. Mount the

fan on the processor according to the instructions provided by the

manufacturer. The fan is a key component that will ensure system

stability. The fan prevents overheating, therefore prolonging the life

of your CPU.

Note: Remember to connect the fan to the appropriate power

source.

1 2

3 4

S

o

c

k

e

t

3

7

0

S

o

c

k

e

t

3

7

0

S

o

c

k

e

t

3

7

0

S

o

c

k

e

t

3

7

0

Hardware Setup SY-7IZB

10

Step 3. SDRAM Memory Module Installation

This Motherboard features 3 x DIMM for 168-pin 3.3V unbuffered

DIMM modules, providing support for up to 256MB of main memory

using DIMM modules from 8MB to 128MB.

Number of

Memory Modules

DIMM 1 DIMM 2 DIMM 3

1

Double-sided

/Single-sided

Double-sided

2

Double-sided

/Single-sided

Double-sided

3

Double-sided

/Single-sided

Single-sided Single-sided

RAM Type

SDRAM

Memory Module

Size (MB)

8/16/32/64/128 Mbytes

Note: Because DIMM 2 and 3 are shared, double-sided DIMMs can be used in

only one of the DIMMs. With single-sided DIMMs both 2 and 3 can be used.

*

2

DIMM1

DIMM3

DIMM2

Hardware Setup SY-7IZB

11

Step 4. IDE Device Installation (HDD, CD-ROM)

This Motherboard offers two primary and secondary IDE device

connectors (IDE1, IDE2). It can support up to four high-speed HDD

or CD-ROM.

Connect one side of the 40-pin flat cable to the IDE device (HDD or

CD-ROM) and plug the other end to the primary (IDE1) or secondary

(IDE2) directionally keyed IDE connector on the Motherboard.

This Motherboard can support up to four HDDs.

Step 5. Floppy Drive Installation

The system supports 5 possible floppy drive types: 720 KB, 1.2 MB,

1.44 MB, 2.88 MB, and LS-120. In addition, this Motherboard

supports a 3-mode (720KB/1.25MB/1.44MB) floppy commonly used

in Japan.

Connect one side of the 34-pin flat cable to the floppy drive and plug

the other end to the floppy drive connector on the Motherboard.

This Motherboard can support up to 2 floppy drives.

Hardware Setup SY-7IZB

12

Step 6. Front Panel Connections

Plug the computer case's front panel devices to the corresponding

headers on the Motherboard.

1. Power LED & KeyLock

Plug the Power LED cable into the 5-pin Keylock header.

Some systems may feature a KeyLock function with a front panel

switch for enabling or disabling the keyboard. Connect the KeyLock

switch to the 5-pin Keylock header on the Motherboard.

Please install according to the following pin assignment: pin 1,3 are

for Power LED and pin 4,5 are for Keylock.

*

2

Speaker

Keylock

Power

LED

_

_ _

+

RST

PWR

ACPI

LED

HDDLED

Hardware Setup SY-7IZB

13

2. Reset

Plug the Reset push-button cable into the 2-pin Reset header on the

Motherboard. Pushing the Reset button on the front panel will cause

the system to restart the boot-up sequence.

3. Speaker

Attach the 4-pin PC speaker cable from the case to the Speaker

header on the Motherboard.

4. ACPI LED

Connecting the 2-pin ACPI LED cable to the corresponding ACPI

LED header will cause the LED to light whenever the system is in

ACPI mode.

The manufacturer has permanently set this Motherboard in ACPI

mode due to most hardware and software compliance to ACPI

mode.

5. IDE LED

Attach the 2-pin IDE device LED cable to the corresponding IDE

LED header on the Motherboard. This will cause the LED to lighten

when an IDE (HDD, CD-ROM) device is active.

6. ATX Power On/Off Switch

Attach the 2-pin momentary type switch to the PWRBT header for

turning On or Off your ATX power supply.

Hardware Setup SY-7IZB

14

Step 7. External Peripherals Connections

External devices such as the keyboard, printer, PS/2 mouse,

modem, USB can be connected to the Motherboard. Normally, you

can not plug your devices directly onto the Motherboard, except for

the keyboard that plugs directly into the back panel KB connector.

For other parallel (PRT1) and serial devices (COM1, COM2), first

install the external connectors that come with your Motherboard on

the computer case, then plug the other end of the flat cable to their

respective connectors.

Only after you have fixed and locked the Motherboard and external

connectors to the computer case can you start connecting the

external peripheral devices.

When connecting an external device, use the following figure to

locate and identify which back panel connector to plug the device or

flat cable to.

*

2

PRT 1

KB

Connector

PS/2 Mouse

Connector

1

COM 2

1

COM 1

1

2

1

10

USB1

Hardware Setup SY-7IZB

15

1. Serial Ports COM1/COM2

External Devices that use the COM ports include serial mice and

modems. The COM port connectors are located on 2 separate

brackets panels, as shown on the figure below. Please plug their

respective 10 pin flat cable connectors into the COM1 and COM 2

serial port connectors on the Motherboard.

The bracket panels should be fixed to one of the slots at the back of

the computer case using a screw, after having finished this you can

plug any serial device into the back panel connectors.

1

10

2

USB1

PS/2 Mouse

Connector

PRT 1

1

COM 1

COM 2

1

KB

Connector

9-pin male external

serial connector (2x)

9-pin serial

flat cables (2x)

Hardware Setup SY-7IZB

16

Parallel Port PRT1

This parallel port is used to connect the printer or other parallel

devices.

Your Motherboard comes with one 25-pin female external parallel

connector with 25-pin flat cable.

Plug the 25-pin end of the flat cable into the PRT1 parallel connector

on the Motherboard, as shown in the figure below, then fix the

bracket to one of the slots at the back of the computer case using a

screw. After having finished this you can plug any parallel device

into the back panel connectors.

AT Keyboard

Plug the keyboard jack directly into the 5-pin female AT keyboard

connector located at the rear panel of the Motherboard.

AT Keyboard

Connector

1

10

2

USB1

PS/2 Mouse

Connector

PRT 1

1

COM 1

COM 2

1

KB

Connector

25-pin female external

parallel connector

25-pin parallel

flat cable

Hardware Setup SY-7IZB

17

PS/2 Mouse

Attach the mouse cable to the 6-pin male PS/2 mouse connector on

the Motherboard to enable PS/2 mouse function.

Universal Serial Bus (USB)

This Motherboard provides a dual-row 10-pin header (one pin is

empty) to support two USB ports for your additional devices. Attach

the USB cable (Optional) to this header as shown in the diagram

below. The USB cable has two USB ports mounted on a bracket.

1

10

2

USB1

PS/2 Mouse

Connector

PRT 1

1

COM 1

COM 2

1

KB

Connector

1

10

2

USB1

PS/2 Mouse

Connector

PRT 1

1

COM 1

COM 2

1

KB

Connector

1

Page is loading ...

SOYO SY-7IZB User manual

SOYO SY-7IZB User manual

Related papers

Other documents