Barco RS90001SWW/03 User manual

Page is loading ...

Barco nv

President Kennedypark 35, 8500 Kortrijk, Belgium

Phone: +32 56.23.32.11

Fax: +32 56.26.22.62

Support: www.barco.com/esupport

Visit us at the web: www.barco.com

Printed in China

1. Safety

1. SAFETY

About this chapter

Read this chapter attentively, it contains important information to prevent personal injury while using ClickShare. It also includes

several cautions to prevent damage to the ClickShare product. Ensure that you understand and follow all safety guidelines, safety

instructions a nd warnings in this chapter before using your ClickShare.

Covered ClickShare products

Regional version Contains Accessories included

R9861008xx

1

• R9861008

• 2x R9861006D01

• DC adapter with AC clips type A, C,

G, I

• USB stick with user documentation

• Printed safety manual

• Wall mount bracket

• 2 antennas

Contact your local sales representative for the correct regional variant necessary in your environment.

About this guide

Part n u mb er Description Level

R5900015

Safety G uide

Any person that comes in contact with the

ClickShare product

Always check for the latest version of the manual on www.barco.com/clickshare Click on Visit the ClickShare

product page and go to tab Downloads..

List of available ClickShare documents

The ClickShar e documentation consists of the following manuals:

Guide Article number

User Guide R5900013

Installation Guide R5900014

Safety Guide (this manu al) R5900015

Service Guide R5900016 ( O nly available to C ustomer Service partners)

Button Guide R5900007

Recycling Manual R5900009 (Available upon r equest)

A printed copy of the Safety Guide and Quick Start Guide is included in the ClickShare box at purchase. Please

check o nline for the other do cum ents.

1.1 General safety

Safety warnings

The installation of the device must comply with the guidelines in the C lickShare Installation Guide (R 5900014).

1. xx=EU, CN, NA, WW

R5900015 CLICKSHARE 01/04/2014 1

1. Safety

• Only use the DC power adapter supplied with the ClickShare device.

• To pr event injuries and physical damage, always read this manual and all labels on the system before connecting to the wall

outlet.

• The ClickShare product is intended to be used in ofﬁce an d indoor environments only.

• Only use the power cord supplied with yo ur dev ice. While appearing to be similar, other power cords have n ot be en safety

tested at the factory and may not be us ed to power the device. For a replacement power cord, contact your dealer.

• This product should be operated from an A C power source. P ower input is a uto-ranging from 100 V t o 240 V @ 50 to 60 Hz.

• Do not allow anything t o rest on the power c ord. Do not loc ate this product where persons will walk on the c ord. To disconnect

the cord, pull it out by the plug. Never pull the cord itself.

• If an extension cord is used with this product, make sure that the total of the Ampere ratings on the products plugged into the

extension cord does not exceed the extension cord Ampere ra ting.

• Never spill liquid of any kind on the product. Should any liquid or s olid object fall into the cabinet, unplug the se

t and have it

checked by qualiﬁed service personnel before resuming operations.

• Lightning - For added protection for this p roduct during a lightning storm, or when it is left unattended and unused for long

periods of time, unplug it from the w all outlet. This will prevent damage to the device due to lightning a n d A C power-line s urges.

• Only use attachments/accessories s peciﬁed by the manufacturer.

WARNING: Ensure you understand and follow all safety guidelines, safety instructions, warnings and cau-

tions mentioned in the product documentation.

WARNING: The m ains power plug connected to the wall outlet m ust be easily accessible at all times for all

installation modes.

Environment

Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing s erious damage to it.

1.2 Service

Risk of electric shock

Do not o pen. To reduce the risk o f electric shock, do not rem ove the cov er. No user- serviceable parts inside. Refer all servicing to

qualiﬁed service personnel.

Unplug this product from the wall outlet and refer servicing to qualiﬁed service personnel under the following conditions:

• When the power cor d or plug is dam aged or frayed.

• If liquid has been spilled into the equipment.

• If the product has been exposed to rain or water.

• If the product does not ope rate normally when the operating instructions are followed. Adjust only those controls that a re

covered by the operating instructions s ince improper adjustment of the other controls ma y result in dam age and will often

require ex tensive work by a qualiﬁed technician to restore the product to normal operation.

• If the product has been dropped or the cabinet has been damaged.

• If the product e xhibits a distinct change in performance, indicating a need for service.

• Replacement parts: W hen replacement parts are required, be sure the service technician has used original BARCO replace-

ment parts or authorized replacement parts which hav e the sam e characteristics as the BARCO original part. Unauthorized

substitutions may result in degraded per formance and reliabilit

y, ﬁre, electric shock or other hazards. Unauthorized substitu-

tions may void warranty.

• Safety check: Upo n com pletion of any service or r epairs to this device, as k the service technician to per form safety checks to

determine that the product is in proper operating condition.

1.3 Heat and ﬁre hazard

Heat and Fire Hazard

Warning – risk of ﬁre: do not place ﬂammable or com bustible materials near the device!

Barco products are designed and manufactured to m eet the m ost stringent safety regulations.

This device radiates heat on its external surfaces during normal opera tion, which is both normal and safe. Exposing ﬂammable or

combustible materials into close proximity of this device could re sult in the spontaneous ignition of that m aterial, resulting in a ﬁre.

For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the device where no ﬂammable

2

R5900015 CLICKSHARE 01/04/2014

1. Safety

or combustible materials are present. The exclusion zone must be not less than 40 c m (16”) for all Barco devices. Do not cover the

device with any material while the it is in operation.

Mount the device in a we ll ventilated area away from sources of ignition and out of direct sun light.

In the event of ﬁre, use sand, CO2, or dry powder ﬁre extinguishers; never use water on an electrical ﬁre.

1.4 Environmental Condition Check

Environment condition check

For installations in environments whe re the device is subject to excessive dust, then it is highly advisable and desirable to have this

dust removed prior to it reaching the device clean air supply. Devices or structures to extract or shield exces sive dust well away

from the device are a prerequisite; if this is not a feasible solution then measures to r elocate the device to a clean air environment

should be considered.

It is the client’s responsibility to ensure at all times that the device is protected from the harmful effects of hostile airborne particles

in the environm ent of the dev ice. T he manufacturer reserves the right to refuse repair if a device has b een subject to negligence,

abandon or improper use .

Ambient temperature conditions

Max. ambient temperature : +40°C or 104°F

Min. am bient temperature: 0°C o r 32°F

Storage temp erature: -10°C to +60°C (14°F to 1 40°F)

Humidity Conditions

Storage: 0 to 90% relative humidity, non-condensing

Operation: 0 to 85% relative humidity, n on-conden sing

Environment

Do not install the device in a site near heat sources su ch as radiators or air ducts, or in a place subject to direct sunlight, ex cessive

dust or humidity. Be aware that room heat rises to the c eiling; check that temper ature near the installation site is not excessive.

1.5 Adapter types

Refer to http://www.iec.ch/worldplugs for the type r e ference.

Ty pe A power input AC clip

Image 1-1

Ty pe C power input AC clip

Image 1-2

R5900015 CLICKSHARE 01/04/2014 3

1. Safety

Ty pe G power input AC clip.

Image 1-3

Ty pe I power input AC clip (two pins)

Image 1-4

1.6 Compliance FCC

Federal Communication Commission Interference Statement

You are c autioned that changes or m odiﬁcations not expressly

approved by the part responsible for compliance c ould void the user’s

authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

Rules. The se limits are designed to provide reasonable protection against harmful interference when the equipment is operated in

a comm ercial environment. T his equipment generates, uses, and can radiate radio frequency energy and, if not installed an d used

in accordance with the instruction manual, may cause harmful interference to ra dio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his

own expense.

If this eq uipment does ca use interference with r adio communications se rvices, w hich can be determ ined by turning the equipment

off and on, you are encouraged to try to correct the interference by one or more of the following meas ures:

• Reorient or re locate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit d ifferent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device co mplies with Part 15 of the FCC R ules. Operation is subject to the following two c onditions:

1. this device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may c ause undesired opera tion of the device.

FCC RF Radiation Exposure Statement: T his device is capable of operating in 802.11a mode. For 802.11a dev ices operating in the

frequency range of 5.15 - 5.25 GHz, they are re stricted for indoor operations to reduce any potential harmful interference for M obile

Satellite Services (MSS) in the US . WIFI Access Points that are capable of allowing your device to operate in 802.11a m ode (5 .15

- 5.25 GHz band) are optimized for indoor use only. If y our W IFI network is capab le of operating in this m ode, please restrict your

WIFI use indoors to n ot v iolate federal regulations to protect Mobile Satellite Services.

Base Unit FCC ID: RYK-W UBR 5 07N

Button FC C ID: XF6-RS9110N1103

1.7 International Safety Standards

Standards overview

This equ ipment is built in accordan

ce with the requirements o f the international safety standards IEC60950-1, E N60950-1,

UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment including

electrical bus iness equipment. Thes e s afety standards impose important requirements on the us e of safety critical components,

materials and insulation, in or

der to protect the user or operator against risk of electric shock and energy haz ard and having access

to live parts. Safety standards also impo se limits to the internal and external temperature rises, radiation levels, mechanical stability

4

R5900015 CLICKSHARE 01/04/2014

1. Safety

and strength, enclosure construction and protection against the risk of ﬁre. Simulated s ingle fault condition testing ensures the

safety of the equipment to the user even when the e quipment’s normal operation fails.

1.8 Compliance IC

Canada, Industry Canada (IC) Notices

This device complies w ith Industry Canada licence-exempt RSS standard(s). Operation is subject to th

e following two conditions:

(1) this device m ay not c ause interference, and (2) this device must accept any interference, including interference that ma y cause

undesired operation of the device.

Radio Frequency (RF) Exposure Information

The radiated output power of the Barco Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The

Barco Wireless Device should be used in such a manner such that the po tential for human contact during normal operation is mini-

mized.

Base Unit IC ID: 61 58A-WUB R507N

Button IC ID: 8407A-RS9110N1103

IC Antenna statement

Under Industry Ca nada regulations, this radio transmitter may only ope

rate using an antenna of a t ype and maxim um (or lesser)

gain approved for the transmitter by Industry C anada. To reduce potential radio interference to other users, the antenna type and

its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not m ore than that necessary for successful

communication.

This radio transmitter 6158A-WUBR507N has been approved by Industry Canada to operate with the antenna types listed below

with the maximum permissible gain and required antenna im pedance for each antenna type indicated. Antenna types not included

in this list, having a g ain gre ater than the m aximum gain indicated for that type, are strictly prohibited for us e with this device.

Type: Dipole

Maximum Peak Gain: 2 dBi

Impedance: 5 0 Ohm

1.9 TRA Approval United Arab Emirates

TRA approval

TRA

REGISTERED No:

ER0116289/13

DEALER No:

0015331/08

ButtonBase

TRA

REGISTERED No:

ER0124406/14

DEALER No:

0015331/08

Image 1-5

R5900015 CLICKSHARE 01/04/2014 5

Page is loading ...

ClickShar e

Sicherheitsh andbuch

R5900015DE/01

18/10/2013

Barco nv

President Kennedypark 35, 8500 Kortrijk, Belgium

Fon: +32 56.23.32.11

Fax: +32 56.26.22.62

Support: www.barco.com/esupport

Besuchen Sie uns im Internet:: www.barco.com

Gedruckt in China

Page is loading ...

ClickShar e

Manual de seguridad

R5900015ES/02

22/01/2014

Barco nv

President Kennedypark 35, 8500 Kortrijk, Belgium

Teléfono: +32 56.23.32.11

Fax: +32 56.26.22.62

Soporte: www.barco.com/esupport

Visite nuestra web: www.barco.com

Impreso en China

Page is loading ...

ClickShar e

Manuel de sécurité

R5900015FR/01

18/10/2013

Barco nv

President Kennedypark 35, 8500 Kortrijk, Belgium

Tél.: +32 56.23.32.11

Fax: +32 56.26.22.62

Support: www.barco.com/esupport

Rendez nous visite sur le web: www.barco.com

Imprimé en Chine

Page is loading ...

ClickShar e

Man uale per la sicurezza

R5900015IT/01

18/10/2013

Barco nv

President Kennedypark 35, 8500 Kortrijk, Belgium

Phone: +32 56.23.32.11

Fax: +32 56.26.22.62

Supporto: www.barco.com/esupport

Visitate il web: www.barco.com

Stampato in Cina

Page is loading ...

ClickShar e

Ve ilig heids hand leid ing

R5900015NL/01

18/10/2013

Barco nv

President Kennedypark 35, 8500 Kortrijk, Belgium

Tel.: +32 56.23.32.11

Fax: +32 56.26.22.62

Support: www.barco.com/esupport

Bezoek ons op het web: www.barco.com

Gedrukt in China

Page is loading ...

ClickShar e

Manual de segurança

R5900015PT/02

01/04/2014

Barco nv

President Kennedypark 35, 8500 Kortrijk, Belgium

Telefone: +32 56.23.32.11

Fax: +32 56.26.22.62

Suporte: www.barco.com/esupport

Visite-nos na internet: www.barco.com

Impresso em China

Page is loading ...

ClickShar e

Manual de segurança

R5900015PT-BR/02

18/10/2013

Barco nv

President Kennedypark 35, 8500 Kortrijk, Belgium

Telefone: +32 56.23.32.11

Fax: +32 56.26.22.62

Support: www.barco.com/esupport

Visite-nos na web: www.barco.com

Impresso em China

Page is loading ...

Barco RS90001SWW/03 User manual

This manual is also suitable for

Barco RS90001SWW/03 User manual

in other languages

Related papers

Other documents