Barco ClickShare CSM-1 User manual

Page is loading ...

Barco nv

Noordlaan 5, B-8520 Kuurne

Phone: +32 56.36.82.11

Fax: +32 56.36.883.86

Support: www.barco.com/esupport

Visit us at the web: www.barco.com

Printed in China

1. Safety

1. SAFETY

About this chapter

Read this chapter attentively, it contains important information to pr event pe rsonal injury while using ClickShare. It also includes

several cautions to prevent dam age to the ClickShare product. Ensure that you understand and follow all safety guidelines, safety

instructions and warnings in this chapter b efore us ing you r C lickShare.

Covered ClickShare products

Regional version Contains Accessories included

R9861017xx

1

• R9861017

• 2x R9861006D01

• DC ada pter with AC clips type A, C ,

G, I

• USB stick with user doc umen tation

• Printed safety manual

• Wa ll mount br acket

• 2 antennas

Contact your local sales representative for the correct regional variant necessary in your environment.

About this guide

Part n um ber Description Level

R5900019

Safety Guide

Any person that comes in contact with the

ClickShare product

Always check for the latest version of the manual on www.barco .com/clicks har e Click on Visit the ClickShare

product page and go to tab Downloads..

List of available ClickShare documents

The ClickShare documentation consists of the following m anuals:

Guide Article number

User Guide R5900013

Installation Guide R5900014

Safety Guide (this manual) R5900019

Service Guide R5900016 ( Only available to Customer Service partners)

Button Guide R5900007

Recycling Manual R5900009 (Available upon request)

A printed copy o f the Safety Gu ide is included in the ClickShare box at purchase. P lease check online for the

other doc umen ts .

1.1 Gen eral safety

Safety warnings

The installation of the device must comply with the guidelines in the ClickShare Installation G uide (R5900014).

1. xx=EU, CN, NA, WW

R5900019 CLICKSHARE 16/02/2015 1

1. Safety

• Only use the DC power adapter supplied with the ClickShare device.

• To prevent injuries and physical damage, always read this m anual and all labels on the system before c onnecting to the wall

outlet.

• The ClickShare produc t is intended to be used in ofﬁce and indoor environments only.

• Only use the power cord supplied with your device. W hile appearing to be s imilar, other power cords have not be en safety

tested at the factory and may not be used to powe r the device. For a replacement power cord, contact your dealer.

• This product should be operated from an A C power source. P ower input is auto-ranging from 100 V to 240 V @ 50 to 60 Hz.

• Do not allow anything to rest on the power cord. D o not loc ate this product where persons will walk on the c ord. To disconnect

the cord, pull it out by the plug. Never pull the cord itself.

• If an extension c ord is used with this p roduct, make sure that the total of the Ampere ratings on the products plugged into the

extension cord does not exceed the extension cord A mpere ra ting.

• Never spill liquid of any kind on the product. Should any liquid or s olid object fall into the cabinet, unplug the se

t and have it

checked by qualiﬁed service personnel before resuming op erations.

• Lightning - F or added protection for this product during a lightning storm, or when it is left unattended and unused for long

periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.

• Only use attachments/accessories speciﬁed by the manufacturer.

• ClickShare model R9861008 is ESD (Electro-Static Discharge) sensitive. In case of an ESD discharge, the unit may reboot

after which it shall return to a state ready to be used by the end user.

WARNING: Ensure you understand and follow all safety guidelines, safety instructions, warnings and cau-

tions mentioned in the product documentation.

WARNING: The m ains power plug connected to the wall outlet must be easily accessible at all times for all

installation modes.

Environment

Do not place this equipment on an unstable cart, stand, or table. The pr oduct may fall, causing serious dam age to it.

1.2 Service

Risk of electric shock

Do not o pen. To reduce the r isk of electric sh ock, do not remove the cover. No user- serviceable parts inside. Refer all servicing to

qualiﬁed service personnel.

Unplug this product from the wall outlet and refer s ervicing to qualiﬁed service pers onnel under the following conditions:

• When the power cord or plug is dam aged or frayed.

• If liquid has been spilled into the equipment.

• If the product has been exposed to rain or water.

• If the product does n ot ope rate normally when the operating instructions are followed. Adjust only those c ontrols that are

covered by the operating instructions since improper adjus tment of the other controls may res ult in damage and will often

require ex tensive work by a qualiﬁed technician to restore the p roduct to normal operation.

• If the product has been dropped or the cabinet has been damaged.

• If the product exhibits a distinct change in performance, indicating a need for service.

• Replacement parts: W hen replacement parts are required, be sure the service technician has used original B ARCO replace-

ment parts or authorized replacement parts which have the same characteristics as the BARCO original part. Unauthorized

substitutions may r esult in degraded performance and reliability, ﬁre, elec tric shock or other hazards. Unauthorized substitu-

tions m ay void warranty.

• Safety check: Upo n completion of any s ervice or r epairs to this device, ask the s ervice technician to perform safety check s to

determine that the product is in proper operating condition.

1.3 Heat and ﬁre hazard

Heat and Fire Hazard

Warning – risk of ﬁre: do not place ﬂamma ble or com bustible materials near the device!

Barco products are des igned and manufactured to meet the m ost stringent safety regulations.

2

R5900019 CLICKSHARE 16/02/2015

1. Safety

This device radiates heat on its external surfaces during normal operation, which is both normal and safe. Exposing ﬂamma ble or

combustible m aterials into close proximity of this device could result in the spontaneous ignition of that m aterial, resulting in a ﬁre.

For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the device where no ﬂamm able

or combustible materials are present. The ex clusion zone m ust be not less than 40 cm (16”) for all Barco devices. Do not cover the

device w ith any m aterial while the it is in operation.

Mount the device in a w ell ventilated area away f rom sources of ignition a nd out of direct sun light.

In the event of ﬁre, use sand, CO2, or dry powder ﬁre extinguishers; never use water on an electrical ﬁre.

1.4 Environmental Condition Check

Environment c ondition check

For installations in environments whe re the device is subject to excessive dust, then it is highly advisable and desirable to have this

dust removed prior to it reaching the device clean air supply. Dev ices or structures to extract or shield excessive dust well away

from the dev ice are a prerequisite; if this is not a feasible solution then measures to r elocate the device to a clean air environment

should be considered.

It is the client’s responsibility to ensure at a ll times that the device is protected from the harmful effects of hostile airborne particles

in the environment of the device. The manufacturer reserves the right to refuse repair if a device has been subject to negligence,

abandon or improper use.

Ambient temperature conditions

Max. ambient temperature : +40°C or 104°F

Min. am bient temperature: 0°C or 32°F

Storage temperature: -10°C to +60°C (14°F to 140°F)

Humidity Conditions

Storage: 0 to 90% relative humidity, non-condensing

Operation: 0 to 85% relative humidity, non-condensing

Environment

The ClickShare product is intended to be used in ofﬁce and indoor environments only.

Do not install the device in a site near hea t sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive

dust or hum idity. Be aware that room heat rises to the

ceiling; check that temperature near the installation site is not excessive.

1.5 Adapter types

Refer to http://www.iec.ch/worldplugs for the ty pe reference.

Power input AC clip

Image 1-1

Type A

Image 1-2

Type C

Image 1-3

Type G

Image 1- 4

Type I

R5900019 CLICKSHARE 16/02/2015 3

1. Safety

1.6 Compliance FCC

Federal Communication Commission Interference Statement

You are cautioned that c hanges or m odiﬁc ations not expressly approved by the part responsible for compliance could void the user’s

authority to operate the equipment.

This equipment has been tested and found to com ply w ith the limits for a Class A digital device, pursua nt to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the e quipment is operated in

a comm ercial environm ent. This equipment generates, uses, and can radiate radio frequenc y energy and, if not installed and us ed

in accordance w ith the instruction m anual, may cause harmful interference to radio comm unications. Operation of this equipment

in a residential area is likely to cause harmful interference in w hich case the user w ill be required to cor rect the interference at his

own expense.

If this eq uipment does ca use interference with radio communications services, w hich can be determined by turning the equipment

off and on, you are encouraged to try to correct the interference by one or more of the following meas ures:

• Reorient or re locate th e receiving antenna.

• Increase the separation between the equipment and receiver.

• Connec t the equipment into an outlet on a circuit different from that to which the receiver is con

nected.

• Consult the dealer or an experienced radio/TV technician for help.

This dev ice complies with Part 15 of the FCC R ules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may c ause undesired opera tion of the device.

FCC RF Radiation Exposure Statement: This device is c apable of operating in 802.11a mode. For 802.11a devices oper ating in t he

frequency range of 5.15 - 5.25 GHz , they are restricted for indoor operations to reduce any potential harmful interference for Mobile

Satellite Services (MSS ) in the US. WIFI Access P oints that are capable of allowing your device to operate in 8 02.11a mode (5 .15

- 5.25 GHz band) are optimized for indoor use only. If your W IFI network is capab le of operating in this m ode, pleas e res trict your

WIFI use indoors to n ot violate federal regulations to protect Mobile Satellite Services.

Base U nit FCC ID: 2AAED-R9861017

Button FCC ID: XF6-RS9110N1103

1.7 EN55022-CISPR22 Class A ITE (Informatio n Technology Equipment)

Statement

Class A ITE is a category of all other ITE whic h satisﬁes the class A ITE limits but not the class B ITE limits. Suc h equipment s hould

not be res tricted in its sale but the following warning shall be included in the instructions for use:

Warning : This is a class A pr oduct. In a dom estic e nvironment this product may cause r adio interference in w hich case the user

may be required to take adequate measures.

1.8 International Safety Standards

Standards overview

This equ ipment is built in accordance with the requirements o f the international safety standards IEC60950 -1, E N60950-1,

UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment including

electrical bus iness equipment. These safety standards impose im portant requirements on the use of safety critical components,

materials and ins ulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access

to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mec hanical stability

and strength, e nclosure cons truction an d protection against the risk of ﬁre. Simulated single fault condition testing ensures the

safety of the equipm ent to the user even w he n the e quipment’s norm al operation fails.

1.9 Compliance IC

Canada, Industry Canada (IC) Notices

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device m ust ac cept any interference, inc luding interference that may cause

undesired ope ration of the dev ice.

4

R5900019 CLICKSHARE 16/02/2015

1. Safety

Radio Frequency (RF) Exposure Information

The radiated output power of the Barco Wireless Device is below the Industry Canada (IC) radio f requency exposu re limits. The

Barco Wireless Device should be used in such a manner such that the po tential for huma n contact during normal operation is mini-

mized.

Base Unit IC ID: 9393B-R9861017

Button IC ID: 8407A-RS9110N1103

IC Antenna statement

Under Industry Ca nada r egulations, this radio transmitter may only operate using a n antenna of a type and maximum (or lesser)

gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and

its gain should be so chosen that the equiva lent isotropically radiated power (e.i.r.p.) is not m ore than that necessary for successful

communication.

This radio transmitter 9393B-R9861017 has been a pproved by Industry Canada to operate with the antenna types listed below with

the maximum permissible gain and req uired antenna impedance for each antenna type indicated. Antenna types not included in this

list, having a gain greater than the max imum gain indica ted for that type, are strictly prohibited for use with this device.

Type: Dipole

Maximum Peak G ain: 2 dB i

Impedance: 5 0 Ohm

1.10 TRA Approval United Arab Emirates

TRA approval

TRA

REGISTERED No:

ER0116289/13

DEALER No:

0015331/08

ButtonBase

TRA

REGISTERED No:

ER37284/15

DEALER No:

0015331/08

Image 1-5

1.11 CE Certiﬁcation

CE Certiﬁcate

R9861017EU is ﬁt for use in all European Union countries, Norway and Switzerland.

Image 1-6

The CE certiﬁcate can be found on the following page.

R5900019 CLICKSHARE 16/02/2015

5

1. Safety

Image 1-7

6 R5900019 CLICKSHARE 16/02/2015

Page is loading ...

1. Sicherheit

Abbildung 1-6

6 R5900019DE CLICKSHARE 10/12/2014

Page is loading ...

1. Sécurité

Image 1-6

6 R5900019FR CLICKSHARE 10/12/2014

Page is loading ...

1. Sicurezza

Immagine 1-6

6 R5900019IT CLICKSHARE 10/12/2014

Page is loading ...

1. Veiligheid

Beeld 1-6

6 R5900019NL CLICKSHARE 10/12/2014

Page is loading ...

1. Segurança

Imagem 1-6

6 R5900019PT CLICKSHARE 10/12/2014

Page is loading ...

Barco ClickShare CSM-1 User manual

Barco ClickShare CSM-1 User manual

in other languages

Related papers

Other documents