BEGLEC DSP-6 Owner's manual

WWW.BEGLEC.COM

Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.

Version: 1.1

Operation Manual

Mode d'emploi

Gebruiksaanwijzing

Bedienungsanleitung

Manual de instrucciones

Manual do utilizador

EN

FR

NL

DU

ES

PT

EN - DISPOSAL OF THE DEVICE

Dispose of the unit and used batteries in an environment friendly manner

according to your country regulations.

FR - DÉCLASSER L’APPAREIL

Débarrassez-vous de l’appareil et des piles usagées de manière écologique

Conformément aux dispositions légales de votre pays.

NL - VERWIJDEREN VAN HET APPARAAT

Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke

manier conform de in uw land geldende voorschriften.

DU - ENTSORGUNG DES GERÄTS

Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und

Weise gemäß den Vorschriften Ihres Landes.

ES - DESHACERSE DEL APARATO

Reciclar el aparato y pilas usadas de forma ecologica conforme a las

disposiciones legales de su pais.

PT - COMO DESFAZER-SE DA UNIDADE

Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em

conformidade com as normas vigentes no seu país.

ENGLISH OPERATION MANUAL

JB SYSTEMS® 1/55 DSP6

Thank you for buying this JB Systems product. To take full advantage of all

possibilities, please read these operating instructions very carefully.

FEATURES

This unit is radio-interference suppressed. This product meets the requirements of the

current European and national guidelines. Conformity has been established and the

relevant statements and documents have been deposited by the manufacturer.

• 6 channel Dimmer + Switch pack

• Max load 10A per channel with automatic 10A circuit breakers

• DMX and analog 0/10V inputs

• Block or individual channel addressing (soft patch)

• Overall or individual channel switch/dimmer mode (linear or square curve)

• Overall or individual channel presets 0-100% (no control panel needed)

• Overall or individual channel preheats 0-50%

• DMX-failure: auto DMX-hold, auto analog 0/10V or auto built-in patterns

• Phase Correction for linear dimming curves

• LCD display with channel output indications

• 3-Phase and single phase 230Vac 50~60Hz inputs

• Power failure memory

BEFORE USE

Check the contents:

Check that the carton contains the following items:

• DSP6 dimmer/switch pack

• Operating instructions

Some important instructions:

• Before you start using this unit, please check if there’s no transportation damage.

Should there be any, do not use the device and consult your dealer first.

•

Important:

This device left our factory in perfect condition and well packaged. It is

absolutely necessary for the user to strictly follow the safety instructions and

warnings in this user manual. Any damage caused by mishandling is not subject to

warranty. The dealer will not accept responsibility for any resulting defects or

problems caused by disregarding this user manual.

• Keep this booklet in a safe place for future consultation. If you sell the fixture, be

sure to add this user manual.

• To protect the environment, please try to recycle the packing material as much as

possible.

ENGLISH OPERATION MANUAL

JB SYSTEMS® 2/55 DSP6

CAUTIONS REGARDING HANDLING

CAUTION: To reduce the risk of electric shock,

do not remove the top cover. No user-

serviceable parts inside. Refer servicing to

qualified service personnel only.

The lightning flash with arrowhead symbol within the equilateral triangle is

intended to alert the use or the presence of un-insulated “dangerous voltage”

within the product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the

user to the presence of important operation and maintenance (servicing)

instructions in the literature accompanying this appliance.

• To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

• To avoid condensation to be formed inside, allow the unit to adapt to the surrounding

temperatures when bringing it into a warm room after transport. Condense

sometimes prevents the unit from working at full performance or may even cause

damages.

• This unit is for indoor use only.

• Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction

may result. If a foreign object enters the unit, immediately disconnect the mains

power.

• Don’t cover any ventilation openings as this may result in overheating.

• Prevent use in dusty environments and clean the unit regularly.

• Keep the unit away from children.

• Inexperienced persons should not operate this device.

• Maximum save ambient temperature is 45°C. Don’t use this unit at higher ambient

temperatures.

• Always unplug the unit when it is not used for a longer time or before you start

servicing.

• The electrical installation should be carried out by qualified personal only, according

to the regulations for electrical and mechanical safety in your country.

• Check that the available voltage is not higher than the one stated on the rear panel

of the unit.

• The power cord should always be in perfect condition: switch the unit immediately off

when the power cord is squashed or damaged.

• Never let the power-cord come into contact with other cables!

• This appliance must be earthed to in order comply with safety regulations.

• Don’t connect the unit to any dimmer pack.

• In order to prevent electric shock, do not open the cover. Apart from mains fuse

there are no user serviceable parts inside.

•

Never

repair a fuse or bypass the fuse holder.

Always

replace a damaged fuse with

a fuse of the same type and electrical specifications!

• In the event of serious operating problems, stop using the appliance and contact

your dealer immediately.

• Please use the original packing when the device is to be transported.

• Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

CAUTION

ENGLISH OPERATION MANUAL

JB SYSTEMS® 3/55 DSP6

MAINTENANCE

Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water

inside the unit. Do not use volatile liquids such as benzene or thinner which will

damage the unit.

FRONT PANEL

1. DMX LED: Blinks when a DMX signal is detected.

2. LCD DISPLAY: monitors the current output states of the channels and helps the

user with the setup of the different menus.

In normal working condition the display shows the output states of the channels

(see picture): The screen shows 6 channels. Above each channel there’s a bar

indicating the dimming level of that channel. The first digit shows the name of the

channel that has been last modified. (in the picture the dimming value of channel 6

was the last modified)

3. MENU Button: Used to access the different setup menus. See “Setup menus” for

more information.

4. UP Button: Used to scroll the menus or to increase the values.

5. DOWN Button: Used to scroll the menus or to decrease the values.

6. ESC Button: Used to go one step back in the menu level or to leave the menu

system.

7. CHANNEL BUTTONS: The DSP6 can work without a controller for the input

signals. This is a good option if you just need a certain output level on each

channel over a long time (shops, exhibition booths, pubs etc…) Just press and

hold the channel button of the channel you want to edit. While you keep the

channel button pressed you can use the “up/down” buttons to change the output

level of that channel.

8. CHANNEL INDICATORS: In addition to the LCD display these leds show the

output condition of the channels.

ENGLISH OPERATION MANUAL

JB SYSTEMS® 4/55 DSP6

9. CIRCUIT BREAKERS: In case of a short circuit these circuit breakers switch off to

protect the output stages of the DSP6. After inspection of the installation you can

switch them back on. In normal working condition these circuit breakers are always

switched on.

REAR PANEL

10. DMX INPUT: male XLR-connector used to connect the DSP6 to a DMX controller

or any other DMX unit in the chain.

DMX OUTPUT: female XLR-connector used to connect the DSP6 to the next unit

in the DMX chain.

11. ANALOGUE INPUTS: 8pin DIN connector used for the analogue

0~10Vdc inputs. Refer to the picture on the right for the pinning of

the connector.

Attention: The analogue input only works when the “DMX fail” option is set to

“Analog” and no DMX-signal is connected to the DSP6 (DMX led is off)

12. CHANNEL OUTPUTS: Each of the 6 channels have 2 output

wires. While connecting please pay attention to the “L” and “N” indications on the

back panel.

13. EARTH WIRE CONNECTIONS: Make sure to earth the DSP6 properly!

14. NEUTRAL INPUT WIRES: Neutral input wires. These 3 connectors are linked

together on the inside of the DSP6.

15. PHASE INPUTS: The DSP6 can be connected in single phase or 3phase. Refer to

the next chapter for proper connection.

ENGLISH OPERATION MANUAL

JB SYSTEMS® 5/55 DSP6

CONNECTIONS

This unit may only be installed by qualified personal, following the

rules for electrical installations in your country! After installation

always put the metal covers back in place and make sure to use

proper cable entry glands (see picture) to protect the wires from

unwanted traction and friction.

• SINGLE PHASE INSTALLATION (2 wires “L”+“N”+ earth wire “E”):

• Since you have only 1 phase wire (L) you must make bridges between the

L1/L2/L3 inputs and connect the phase wire to these inputs.

• Connect the neutral (N) to the N-input.

• Connect the loads to the output channels (2 connections, named “L” and “N”) All

connections named “N” are linked inside the DSP6.

• Don’t forget to connect the earth connection properly!

• THREE PHASE INSTALLATION (4wires “L1+L2+L3+N” + earth wire “E”):

• Since you have 3 phase wires you can connect these directly to the corresponding

L1/L2/L3 inputs.

• Connect the neutral (N) to the N-input.

• Connect the loads to the output channels (2 connections, named “L” and “N”) All

connections named “N” are linked inside the DSP6.

• Don’t forget to connect the earth connection properly!

ENGLISH OPERATION MANUAL

JB SYSTEMS® 6/55 DSP6

SETUP MENUS

Please refer to the overview below to fully understand the menu structure of the DSP6:

You can clearly see which buttons to push to select a certain function. In most cases

the DSP6 is in normal working condition (display shows channel output condition).

Push the “menu” button to enter the setup menus. With the “up/down” buttons you can

scroll through the 5 available menus. With the “esc” button you can go one step back

in the menu. After +/-30sec the DSP6 returns automatically to the normal working

mode.

In the next chapter you can read more about each function.

ENGLISH OPERATION MANUAL

JB SYSTEMS® 7/55 DSP6

MENU ITEMS

• DMX FAIL:

The DSP6 works with analog 0/10V or digital DMX-512 input signals. DMX-signals

have priority to the analog inputs. This means that you can only use the analog

inputs when no DMX-signal is detected. When the DMX-signal is not present you

have 3 options:

• Hold:

In case of DMX-fail the DSP6 keeps the last scene on the outputs.

• Press “menu” and “up/down” until the display shows “Dmx fail”.

• Press “menu” again: the display shows one of the 3 options.

• Press “up/down” until the display shows “Hold”

• Press “esc” to store this option and leave the menu.

• Analog:

In case of DMX-fail the DSP6 goes in analog 0/10V mode.

• Press “menu” and “up/down” until the display shows “Dmx fail”.

• Press “menu” again: the display shows one of the 3 options.

• Press “up/down” until the display shows “Analog”

• Press “esc” to store this option and leave the menu.

• Prog 01 … Prog 12:

In case of DMX-fail the DSP6 shows one of the 12 built-in patterns.

• Press “menu” and “up/down” until the display shows “Dmx fail”.

• Press “menu” again: the display shows one of the 3 options.

• Press “up/down” until the display shows the desired program (Prog 01 … 12)

• Press “esc” and “up/down” buttons to select the proper speed.

• Press “esc” to store the selected speed and leave the menu.

• CURVE:

With the DSP6 you can select a different working mode (curve) for each individual

channel. This is a nice feature if you need to switch light effects on/off while at the

same time you have to dim lamps. 3 Curves are available:

• Select a curve for all channels:

• Press “menu” and “up/down” until the display shows “Curve”.

• Press “menu” again: the display shows one of the 2 options.

• Press “up/down” until the display shows “All”

• Press “menu” to select this option.

ENGLISH OPERATION MANUAL

JB SYSTEMS® 8/55 DSP6

• Press “up/down” to select one the 3 curves

• Press “esc” to store the selected curve and leave the menu.

• Select a curve for individual channels:

• Press “menu” and “up/down” until the display shows “Curve”.

• Press “menu” again: the display shows one of the 2 options.

• Press “up/down” until the display shows “Single”

• Press “menu” to select this option: the display shows the channel number on

the first row and the curve on the second row.

• Press “menu” to toggle between both rows.

• Press “up/down” to set the desired curves and channel numbers until all

channels are set.

• Press “esc” to store the selected curves and leave the menu.

• PREHEAT:

On the DSP6 you can set a preheat level up to 50% for all channels in one time or

for each channel separately. While the preheat function keeps the lamp filament at a

certain temperature, the turn on current of the lamp is much lower. This extends the

lamp life considerably in many cases.

• Preheat on all channels:

• Press “menu” and “up/down” until the display shows “Preheat”.

• Press “menu” again: the display shows one of the 2 options.

• Press “up/down” until the display shows “All”

• Press “menu” to select this option.

• Press “up/down” to set the desired overall level.

• Press “esc” to store the selected level and leave the menu.

• Preheat on individual channels:

• Press “menu” and “up/down” until the display shows “Preheat”.

• Press “menu” again: the display shows one of the 2 options.

• Press “up/down” until the display shows “Single”

• Press “menu” to select this option: the display shows the channel number on

the first row and the preheat level on the second row.

• Press “menu” to toggle between both rows.

• Press “up/down” to set the desired preheat levels and channel numbers until all

channels are set.

• Press “esc” to store the selected preheat levels and leave the menu.

• DMX ADDRESSING:

On the DSP6 you can set the DMX start address for the complete unit or for each

channel separately. Due to this “soft patch” option DMX addressing becomes

extremely flexible.

• Setting the start address for the complete unit:

• Press “menu” and “up/down” until the display shows “Dmx addr”

• Press “menu” again: the display shows one of the 2 options.

• Press “up/down” until the display shows “Block”

• Press “menu” to select this option.

• Press “up/down” to set the desired start address for the DSP6.

• Press “esc” to store the selected level and leave the menu.

• Setting the start address for individual channels:

ENGLISH OPERATION MANUAL

JB SYSTEMS® 9/55 DSP6

• Press “menu” and “up/down” until the display shows “Dmx addr”

• Press “menu” again: the display shows one of the 2 options.

• Press “up/down” until the display shows “Single”

• Press “menu” to select this option: the display shows the channel number on

the first row and the DMX address on the second row.

• Press “menu” to toggle between both rows.

• Press “up/down” to set the desired DMX addresses and channel numbers until

all channels are set.

• Press “esc” to store the selected DMX addresses and leave the menu.

• PHASE CORRECTION:

To be able to produce perfectly linear curves the DSP6 has phase correction on

board. Normally this option should always be switched on. However some control

desks have built-in phase correction that can’t be switched off. In these cases the

phase correction of the DSP6 can be switched off.

• Switching phase correction on/off:

• Press “menu” and “up/down” until the display shows “Pha corr”

• Press “menu” again: the display shows one of the 2 options (on/off)

• Press “up/down” until the display shows the desired option.

• Press “esc” to store the selected option and leave the menu.

SPECIFICATIONS

Power Input: Single Phase 230Vac 50~60Hz (2 wires)

Three Phase 230Vac 50~60Hz (4 wires)

Power outputs: Max. 6x 10A (max.10A per channel)

DMX-512 in/out: in: male 3pin XLR ~ out: female 3pin XLR

Analog input: DIN 8pin connector: 0~10Vdc

Size (WxHxD): 483 x 88 x 420mm

Weight: 9kg

Every information is subject to change without prior notice

FRANCAIS MODE D’EMPLOI

JB SYSTEMS® 10/55 DSP6

Nous vous remercions d’avoir acheté ce produit JB Systems. Veuillez lire ce mode

d’emploi très attentivement afin de pouvoir exploiter toutes les possibilités de cet

appareil.

CARACTERISTIQUES

Cet appareil ne produit pas d’interférences radio. Il répond aux exigences nationales

et européennes. La conformité a été établie et les déclarations et documents

correspondants ont été déposés par le fabricant.

• Dimmer + Switch pack à 6 canaux

• Charge maximale de 10A par canal avec disjoncteurs automatiques de 10A

• Entrée DMX et analogique 0/10V

• Fonction switch/dimmer, par canal individuel ou en bloc (courbe linéaire ou carrée)

• Adressage individuel des canaux ou en bloc (soft patch)

• Programmation individuelle des canaux ou de l’unité complète en bloc, de 0-100%

(ne nécessite pas de panneau de contrôle)

• Préchauffe individuel des canaux ou en bloc, de 0-50%

• En cas d’absence de signaux DMX: passage automatique en DMX-hold, en 0/10V

ou au déroulement automatique des programmes internes

• Construction modulaire: très facile à l’entretien!

• Correction de phase pour des courbes de gradation linéaires

• Ecran LCD affichant l’état de sortie de chaque canal

• Entrées monophasés ou triphasés 230Vac 50~60Hz

• Mémoire anti-panne de courant

AVANT L’UTILISATION

Vérifiez le contenu:

Vérifiez si la boite contient les articles suivants :

• DSP6 dimmer/switch pack

• Mode d’emploi

Quelques instructions importantes:

• Avant d’utiliser cet appareil, assurez-vous de l’absence de dommage lié au

transport. En cas d’endommagement, n’utilisez pas l’appareil et contactez le

vendeur.

• Important: Cet appareil a quitté notre usine en parfaite condition et bien emballé. Il

est primordial que l’utilisateur suive les instructions de sécurité et avertissements

inclus dans ce manuel. La garantie ne s’applique pas en cas de dommage lié à une

utilisation incorrecte. Le vendeur ne prend pas la responsabilité des défauts ou de

Page is loading ...

BEGLEC DSP-6 Owner's manual

BEGLEC DSP-6 Owner's manual

in other languages

Related papers

Other documents