Hitachi LE40H405 User manual
- Category
- Video converters
- Type
- User manual
Owner's Guide
Model LE40H405
40” Class (40.00” Diagonal)
IMPORTANT SAFETY INSTRUCTIONS ....................................................................... 2-6
HOW TO ATTACH / REMOVE THE STAND ..................................................................... 7
FIRST TIME USE
.......................................................................................................
10-13
TV OPERATION ........................................................................................................ 13-18
CONNECTIONS TO OTHER EQUIPMENT .............................................................. 19-21
TROUBLESHOOTING ................................................................................................... 22
SPECIFICATIONS .......................................................................................................... 23
LIMITED WARRANTY ............................................................................................... 24-25
END USER LICENCE AGREEMENT FOR HITACHI DTV SOFTWARE ..................26-27
APPENDIXES................................................................................................................. 28
Thank you for purchasing this Hitachi product. Please read these instructions carefully.
For additional assistance please call 1-888-333-1899(U.S.A. or Puerto Rico), or 01-800-700-4321(Mexico)
or visit our website at www.hitachi.us/tv.
Keep this owner’s guide for future reference.
Record the model number and serial number of your LCD Television for future reference.
This information is located on the back of the television.
MODEL NUMBER SERIAL NUMBER
TABLE OF CONTENTS
条形码定位框（尺寸：35×10.5mm)
定位框不做印刷处理，编码规则咨
询采购资源。
ES-J113307
This product contains lead. Dispose of this product in accordance with applicable environmental laws. For product recycling
and disposal information, contact your local government agency or www.eRecycle.org (in California), the Electronic Industries
Alliance at www.eiae.org (in the US) or the Electronic Product Stewardship Canada at www.epsc.ca (in Canada). For more
information, call 1-888-333-1899.
4 inches
4 inches
The unit emits heat when in operation. Do not place any covers or blankets on the unit, this may cause overheating. Do not block
ventilation holes, or set up near radiators. Do not place in direct sunlight. When placing on a shelf leave 4 inches (10 cm) free space
around the entire unit.
Notes when mounting the LCD TV on a wall
If the unit is to be mounted on the wall, contact the retailer where you purchased the LCD TV for advice, and have the equipment pro-
fessionally installed. Incomplete or improper installation may cause injury to you, and/or damage to the LCD TV.
The screws ISO M6 thread type should be used. The insertion length must be within 12 - 16mm.
If the insertion length is less than 12mm, the weight can not be maintained.
If the insertion length is more than 16mm, a space is created between the Wall Mount Bracket and the Television.
(Insertion Length) = (Screw Length) - (Washers Thickness) - (Mounting Bracket Thickness)
NOTICE FOR TV CABINET
If the unit is to be mounted on a cabinet smaller than the length of the unit, it could result in an unstable location and the unit may tumble
over, making a risk of personal, possibly fatal injury. Also, this would damage the product seriously. Accordingly, Hitachi accepts no
responsibility or liability for any injuries or property damage resulting from the improper installation.
YES !!
NO !!
SAFETY PRECAUTIONS
YES!!
NO!!
4 inches
Securing to a Wall
1. Use metallic wire, clamp and screw (not provided) on the rear of the LCD TV as shown below.
2. Use proper hardware (drywall anchor, masonry screw, etc) to secure other end of wire to wall.
Wire
Wire
ScrewM6×10
Clamp
Insert the bracket to the base,and fix them with 6 screws.
Put the TV set on the level table on which there is a pad cloth or other soft material.
Lay down the TV set and make sure the LCD screen is downward.
Then fix the base to the set with 4 screws.
pedestal
4 screws
4 screws
The figure below is just for reference,please see the real set.
The length of Base Screws must be between 10mm and 12mm,otherwise the TV would be damaged.
WARNING:
When you transport this product, remove the stand and pack flat against the back of the unit in the carton. To remove the stand, perform
above steps in reverse order.
For wall mounting, the base must be removed. To disconnect the base/stand remove the 4 screws from the back.
Type A
Type B
40
End User License Agreement
Limited Warranty
SERVICE
HDMI 3
HDMI 2/DVI
HDMI 4 RGB
RGB/DVI
AUDIO
RGB
VIDEO L R
AV
HDMI 1
AIR/CABLE
L RY
PB PR
COMPONENT
DIGITAL
AUDIO OUT
COAXIAL
INPUTMENU
VOL VOL
CH
CH POWER
Antenna connections
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you
are using a Cable TV service, see Cable TV connections.
Combination VHF/UHF Antenna (Single 75 ohm cable)
Cable TV connections
For basic Cable TV service not requiring a Converter/Descrambler box, connect the
75 ohm Coaxial Cable directly to the Antenna Jack on the back of the TV.
For subscribers to scrambled Cable TV service
If you subscribe to a Cable TV service which requires the use of a Converter/Descrambler box, connect the incoming 75 ohm Coaxial
Cable to the Converter/Descrambler box. Using another 75 ohm Coaxial Cable, connect the output jack of the Converter/Descrambler
box to the Antenna Jack on the TV. Follow the connections shown below. Set the TV to the output channel of the Converter/
Descrambler box (usually channel 3 or 4) and use the Converter/Descrambler box to select channels.
For subscribers to unscrambled Cable TV service with scrambled premium channels
If you subscribe to a Cable TV service in which basic channels are unscrambled and premium channels require the use of a
Converter/Descrambler box, you may wish to use a signal Splitter and an A/B Switch box (available from the Cable TV company
or an electronics supply store). Follow the connections shown below. With the switch in the “B” position, you can directly tune any
nonscrambled channels on your TV. With the switch in the “A” position, tune your TV to the output of the Converter/Descrambler box
(usually channel 3 or 4) and use the Converter/Descrambler box to tune scrambled channels.
This TV has an extended tuning range and can tune most cable channels without using a Cable TV Converter box. Some
cable companies offer “premium pay channels” where the signal is scrambled. Descrambling these signals for normal
viewing requires the use of a descrambler device which is generally provided by the Cable TV company.
For subscribers to basic Cable TV service
Incoming 75 ohm Cable TV Cable
75 ohm Cable to TV
Antenna
Jack
Converter/
Descrambler
Splitter
B
A
Incoming
75 ohm
Cable TV
Cable
A/B Switch
75 ohm Cable to TV
Converter/
Descrambler
Antenna
Jack
75 ohm
Coaxial
Cable
Antenna
Jack
75 ohm
Coaxial Cable
Antenna
Jack
Connect the 75 ohm cable from the combination VHF/UHF antenna to the antenna jack.
ENGLISH
Starting setup
will assist you to specify the Air/Cable setting and program
your channels automatically.
IMPORTANT: Make sure that the antenna or cable TV system
connection is made.
1
To turn on the TV, touch POWER (POWER indicator on the
front of the unit changes blue. It may take approx. 10 seconds
for a picture to appear on screen.). The
Setup Wizard
function
begins.
2
Press ▲ or ▼ to select “Source”, then press or to select
“Cable” or “Air”.
3
Press ▲ or ▼ to select “Scan”, then press or SELECT.
4
•
NOTE
•
TV operation
1
To turn on the TV, press POWER.
(POWER indicator on the front of the unit changes blue.
It may take approx. 10 seconds for a picture to appear on
screen.)
2
Adjust the volume level by pressing VOL or . The
volume level will be indicated on the screen by volume bars.
As the volume level increases, so do the number of bars.
If the volume decreases, the number of volume bars also
decreases.
3
Set the Source option to the appropriate position.
4
Press the Direct Channel Selection (0-9, –) buttons to
select the channel.
(If you press only the channel number, channel selection will
be delayed for a few seconds.)
TO SELECT ANALOG CHANNELS
1-9: Press 1-9 as needed. Example, to select channel
2, press 2, then press SELECT .
10-99: Press the 2 digits in order. Example, to select
channel 12, press 1, 2, then press SELECT.
100-135: Press the 3 digits in order. Example, to select
channel 120, press 1, 2, 0, then press SELECT.
TO SELECT DIGITAL CHANNELS
– button followed by
the remaining number.
Example, to select channel 15-1, press 1, 5, –, 1, then press
SELECT.
• If a channel is selected with only audio content, “Audio
only” will be displayed on the screen.
• If a channel is selected with a weak digital signal, “Weak
Signal or No Audio and Video.” will be displayed on the
screen.
• The same program may be available on either an analog
channel or a digital channel. You may choose to watch
either format.
• If a channel is selected to which you have not subscribed,
“Scrambled ” will be displayed on the screen.
VHF/UHF/CABLE CHANNELS
Air Cable
VHF
2-13
VHF
2-13
UHF
14-69
NOTES
• If a channel with no broadcast is selected, the sound will
automatically be muted.
• It may take a few seconds for a digital channel picture to
appear on screen after being selected.
To select the video input source
To view a signal from another device connected to your LCD TV,
such as a VCR player, press INPUT, then press ▲ or ▼, then
press SELECT.You can select TV, Video, Component, HDMI or
RGB depending on which input jacks you used to connect your
devices.
CH /
Press and release CH / . The channel automatically stops at
the next channel set into memory.
For proper operation, before selecting channels, they should be
set into the memory. Refer to the Channels Menu on page 14.
Input
TV
AV
Component
RGB
HDMI 1
HDMI 2
Tuner
Please select your tuner mode:
Cable
Setup Wizard
Move
SEL Select
Return
SEL Select
Air
MENU Return
Move
If you press EXIT in the process of “Setup Wizard”, the Setup
Wizard stops and changes to the normal screen. When you
make a menu selection, your changes occur
immediately. You
do not have to press EXIT to see your changes.
Depending on the reception condition, it may take up to 25
minutes or more to complete memorizing digital cable
channels. Please allow the process to complete without
interruption.
“Setup Wizard” will begin. After the Setup Wizard is
completed, the TV channel appears on the screen.
CATV
Digital Terrestrial Broadcast(8VSB):2-69
Digital cable(64/256 QAM):1-135
1-125
EXIT
EXIT
EXIT
EXIT
Aspect Ratio
EXIT
EXIT
EXIT
EXIT
RGB
( "PC Standby" being only available in RGB input.)
To connect a HDMI or a DVI device to the unit
The HDMI/DVI input receives digital audio and uncompressed video from a HDMI device or uncompressed digital video from a DVI
device.
When you connect to a DVI device with a HDMI-to-DVI adapter cable, it transfers only video signal. Separate analog audio cables are
required.
HDMI - to - DVI adapter cable
(HDMI type A connector) (not supplied)
Audio cord (not supplied)
HDMI cable (type A connector) (not supplied)
To DVI output
To HDMI out
HDMI device
DVI device
To HDMI/DVI IN
or
Back of the unit
When using a HDMI input from a Set-Top-Box, it is recommended to use a 1080p, 1080i or 720p input signal.
When the HDMI input is a 1080p signal, it is recommended that the length of the cable should be less than 5 meters.
RGB/DVI AUDIO Input
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
Hitachi LE40H405 User manual
- Category
- Video converters
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Hitachi L32C205 User manual
-
-
-
-
-
-
-
-
-