RealWear NAVIGATOR 500 User guide

NAVIGATOR 500
Brand
RealWear
Model
NAVIGATOR 500
Type
User guide

RealWear NAVIGATOR 500: Your new wearable computer offers hands-free operation with voice control and head motion, allowing you to work efficiently in challenging environments. The device features a built-in camera for capturing images and videos, and a microphone for clear communication. With its rugged design, long battery life, and expandable memory, the NAVIGATOR 500 is ideal for industrial applications, field service, and remote collaboration.

RealWear NAVIGATOR 500: Your new wearable computer offers hands-free operation with voice control and head motion, allowing you to work efficiently in challenging environments. The device features a built-in camera for capturing images and videos, and a microphone for clear communication. With its rugged design, long battery life, and expandable memory, the NAVIGATOR 500 is ideal for industrial applications, field service, and remote collaboration.

Navigation:
Left/Right
RealWear Navigator 500
Quick Start Guide
3,5mm Audio Jack
USB-C
Display
Window
Rear View
Adjust the
Display so you
can see all 4
corners of the
display and
then lock it into
position using
the locking ring
Adjust camera
position by rotating
up / down for the
best view
Press 2 sec for on,
1 sec for off
Switching on and Adjusting
The Navigator 500 is
controlled simply by
using your voice and
head motion. Speak out
clearly, say what you can
see on the screen. Just
say the the name of the
icon you want to open.
To use the bubbles
with numbers, just say
“select item 1”.
“My Programs”
Voice Input
Exchangeable
battery incl. charge
level indicator
Notch for releasing
the battery
Rechargeable Battery
USB-C charge cable
(included)
Charging the Navigator 500
1. Connect the USB-C charging cable to the USB-C port
located under the rear cover on the same side as the
boom arm.
2. Connect the charging cable to the wall charger and plug
the charger into a wall socket. The power button lights
up ORANGE while charging. The Power button will light
up GREEN, once it reached 90% battery status.
USB-C (under cover)
Regional wall
charger
(included)
Charging the Navigator 500
Workband
Engaging points for
Workband
ATTENTION: Before using the Navigator 500 for the first time, visit
https://www.realwear.at/en/support from another device (phone or computer).
NOTE: Your Navigator 500 is shipped partially charged from the factory. If the
battery level is too low, please see charging instructions below.
Do not extend the display
too far from your eye.
Keep the display as close
to the eye as possible for
the best view.
Adjust the workband so that the HMT-1 rests
horizontally, and the display slightly below the
line of sight
Position the boom arm and elbow joints into a
“Z” shape, below the line of sight, left or right
eye.
Setting up the Display
1
Barcotec Support Kontakt
Mail: support@barcotec.at
Phone: +43 1 786 39 40
Barcotec GmbH, Julius Welser Straße 15
5020 Salzburg
https://www.realwear.at/support
Speaker
Power Button
incl. Fingerprint Sensor
Action
Button
MicroSD Card Slot
(on the inside)
Elbow Joint
Boom-Arm
Mic B1 (B2 on opposite side)
Camera
Display Pod
Mic A1 (A2 on
opposite side)
Front View
Mic B1
(B2 on opposite side)
Battery
Snap-in holder of the
workband
  • Page 1 1

RealWear NAVIGATOR 500 User guide

NAVIGATOR 500
Brand
RealWear
Model
NAVIGATOR 500
Type
User guide

RealWear NAVIGATOR 500: Your new wearable computer offers hands-free operation with voice control and head motion, allowing you to work efficiently in challenging environments. The device features a built-in camera for capturing images and videos, and a microphone for clear communication. With its rugged design, long battery life, and expandable memory, the NAVIGATOR 500 is ideal for industrial applications, field service, and remote collaboration.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents