Page is loading ...
Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
20 08001 0049
Hall Tree Stand
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Dowel
26 pcs. (+1 extra)
M3x16
Flat Head Screw (short)
8 pcs. (+1 extra)
Cam Lock Screw
48 pcs. (+1 extra)
Cam Lock
48 pcs. (+6 extra)
Hook
4 pcs.
D.
Back Panel
2 pcs.
T.
Upright
1 pc.
S.
Back Panel
2 pcs.
O.
Divider
1 pc.
I.
Plinth
2 pcs.
A.
Seat
1 pc.
C.
Side Panel
1 pc.
E.
Back Panel
1 pc.
F.
Base
1 pc.
G.
Middle Panel
1 pc.
B.
Side Panel
1 pc.
H.
Plinth
2 pcs.
M.
Back Rail
1 pc.
N.
Back Rail
1 pc.
J.
Door
2 pcs.
R.
Side Panel
1 pc.
K.
Shelf
1 pc.
Q.
Side Panel
1 pc.
L.
Front Rail
1 pc.
P.
Top
1 pc.
U.
Back Panel
1 pc.
M3.5x64
Wood Screw
12 pcs. (+1 extra)
M3.5x38
Flat Head Screw (long)
12 pcs. (+1 extra)
M3x20
Flat Head Screw
16 pcs. (+1 extra)
Plastic Clip
16 pcs. (+1 extra)
Hinge
4 pcs.
M3.5x14
Wood Screw for Hinge
24 pcs. (+1 extra)
Cover
14 pcs. (+1 extra)
Assembly Instructions 2/9
Figure 1
Cam Lock Screw
STEP 1
Place Seat (A), Side Panels (B), (C), (Q), (R), Base (F), Plinths (H),
Shelf (K), Front Rail (L) and Back Rails (M), (N).
on a soft cloth.
Insert Cam Lock Screws into pre-drilled
holes in Seat (A), Side Panels (B), (C),
(Q), (R), Base (F), Plinths (H),
Shelf (K), Front Rail (L) and
Back Rails (M), (N),
then tighten.
(See Figure 1)
STEP 2
Attach Back Panels (D) to Side Panels (B) and (C)
with Cam Locks. (See Figure 2)
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Figure 2
Cam Lock
B
C
D
D
C
B
K
M
N
Q
R
A
L
H
H
F
Assembly Instructions 3/9
STEP 3
Place Seat (A) upside down on a soft cloth.
Insert Dowels into pre-drilled holes
in Seat (A).
Attach Side Panels (B), (C) and
Back Panels (D) to Seat (A) with
Cam Locks.
Slide Back Panel (E) into position.
Figure 3
STEP 4
Insert Dowels into
pre-drilled holes in unit.
Attach Middle Panel (G)
to unit with Cam Locks.
Attach Base (F) to unit with
Dowels, Flat Head Screws (long)
and Cam Locks. (See Figure 3)
Cam Lock
Dowel
Cam Lock
Dowel
Flat Head Screw (long)
G
F
A
E
D
D
C
B
Assembly Instructions 4/9
STEP 5
Assemble Plinths (H) and (I) with Cam Locks.
Cam Lock
I
I
H
H
STEP 6
Insert Dowels into pre-drilled holes in unit.
Attach plinth unit to unit with Wood Screws.
Wood Screw
Dowel
Assembly Instructions 5/9
Figure 6 Figure 7
UP
Front
Back
Down
Figure 8
Left
Right
STEP 8
If needed, adjust doors up or down by removing the front Wood Screws for Hinge and
loosening slightly the back Wood Screws for Hinge from side panel, adjusting doors up or down
and reinstalling screws. (See Figure 6)
If needed, adjust doors left to right. (See Figure 7)
If needed, adjust doors front to back. (See Figure 8)
STEP 7
Turn unit over to its upright position.
Attach Hinges to Doors (J) with Wood Screws for Hinge
into pre-drilled holes, then tighten. (See Figure 4)
Attach Doors (J) to unit with Wood Screws for Hinge into pre-drilled holes,
then tighten. (See Figure 5)
Insert Cam Lock Screws into pre-drilled holes in unit, then tighten.
Figure 4
Figure 5
Cam Lock Screw
Hinge
Wood Screw for Hinge
J
J
Assembly Instructions 6/9
STEP 10
Insert Dowels into pre-drilled holes in Shelf (K).
Attach Front Rail (L) and Back Rail (M) to Shelf (K) with Cam Locks.
Cover Cam Locks with Covers. (See Figure 10)
Figure 10
M
Cam Lock
Dowel
Cover
K
L
Figure 9
STEP 9
Attach Hooks to Back Rail (M) with Flat Head Screws (short).
(See Figure 9)
Flat Head Screw (short)
Hook
M
Assembly Instructions 7/9
STEP 12
Slide Back Panel (S) into position.
Attach Upright (T) to unit with Cam Locks.
Cam Lock
Cover
Dowel
Dowel
Cam Lock
Cover
STEP 11
Insert Dowel into pre-drilled hole in Side Panel (Q).
Attach unit to Side Panel (Q) with Cam Locks.
Cover Cam Locks with Covers.
Cam Lock
STEP 13
Insert Dowel into
pre-drilled hole in unit.
Slide Back Panel (S) into position.
Attach Back Rail (N) and Side Panel (R)
to unit with Cam Locks.
Cover Cam Locks with Covers.
Q
R
T
S
S
N
Assembly Instructions 8/9
Cover
Flat Head Screw (long)
Dowel
Flat Head Screw
Plastic Clip
Cam Lock
STEP 14
Turn unit to its upright position.
Slide Back Panel (U) into position.
Insert Dowels into pre-drilled holes in unit.
Attach Divider (O) and Top (P) to unit
with Flat Head Screws (long).
Cover Flat Head Screws (long) with Covers.
STEP 15
Attach unit from Step 14 to
unit from Step 7 with Cam Locks.
Level unit by adjusting the adjustable
levelers on bottom of unit. (See Figure 11)
Note: Unit must be level to proceed.
Attach Plastic Clips to unit with
Flat Head Screws. (See Figure 12)
Note: Unit must be level before attaching Plastic Clips.
Figure 11 Figure 12
P
U
O
Drill 3/8” hole in wall
Top of unit
Assembly Instructions 9/9
Hardware List
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x38
Wall Screw
1 pc. (+1 extra)
M3x16
Wood Screw
1 pc. (+1 extra)
STEP 16
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 13)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Bracket
on wall
Anchor in wall
3/8” wall hole
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Figure 13
Wood Screw
Wall Screw
Pre-drilled hole
at top of unit
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
/
