logika Smart Translator WL-ZWWWDPW-0101-01 User manual

Brand
logika
Model
Smart Translator WL-ZWWWDPW-0101-01
Type
User manual
© 2019 Logika Limited
Smart Translator
WL-ZWWWDPW-0101-01
Product Manual
Version 1.0
1
Logika Limited
E
-Centre, Massey University, Gate 5, Oaklands Road
Albany, Auckland 0632, New Zealand
www.logika.nz
· support@logika.nz
Introduction
Thank you for choosing Logika. Please take a moment to carefully read through the manual to
ensure safe and proper installation and use.
• Before use, the product must be properly installed as described in this manual by a qualified
technician.
• The product should be used with the supplied accessories.
• Do not disassemble or modify the product.
• Logika is not responsible for any loss due to improper installation or use of this product.
• Please visit our official website at www.logika.nz for more information.
• You can also contact us at the following email address: support@logika.nz.
2
Device Layout
Terminal Blocks
System Indicator
Multi-Function Button
Power DC 12V
Output 1
Output 2
Ground Wire
3
Features
• Communication Mode: IEEE 802.15.4 Zigbee.
• Space saving.
• Easy to use.
• Support time setting and linkage control to other smart devices.
Specifications
Communication Protocol IEEE 802.15.4
Communication Distance 100m
Port Output
Configuration Double-switched relay output signal
Working Temperature -10°C to +55°C
Power 12V DC
Weight 90g
Net Weight 34g
Colour White
4
Installation Steps
Hardware Installation
1) Connect the device to a DC 12v power source, as shown below.
2) Press and hold the terminal block to open the connector and connect the output cable to
the corresponding terminal. Release to lock the cable in place. Note that the output load
capacity is < 20mA.
Ground
DC 12V
Output 2
Output 1
5
Adding the Device to the Smart Home Network
Use the Logika Smart Home app to add the device to the Smart Home system. Please refer to the
Logika Smart Mobile App user guide which will take you through the process of adding smart
devices to the system.
Refer to the information below to locate the device in the Device Add screen. Once selected, the app
will walk you through how to add the device to the system.
Thermostat
2-Way Translator (Output)
6
Device Functions
When the device is first powered on, it will normally automatically attempt to connect to the Zigbee
Smart Home network. The System Indicator light will flash as it’s searching for the network. If it
connects, the light will remain on for 2 seconds and then go out.
If this does not happen, you can manually connect via the mobile app and follow the instructions
below.
Join the Zigbee Network
Press the Multi-Function Button 4 times in quick succession. The System Indicator light will start
flashing, signifying it’s searching for the network.
When it successfully connects, the System Indicator light will stay solid for 2 seconds then go out.
Quit the Zigbee Network
Long press the Multi-Function Button for 10 seconds. The System Indicator light will flash 4 times and
go out. The device has now been successfully removed from the network and been reset to the
factory defaults.
7
Troubleshooting
The device cannot be added to the Zigbee network.
The device may be registered to another network. In rare occasions this can happen if the device
was not removed from the test network at the factory.
Perform the Quit the Zigbee Network procedure mentioned in Device Functions section to clear this
setting. You should now be free to add the device to the local smart network.
The issue you are experiencing is not mentioned here.
Please contact us at support@logika.nz with your issue and we will do our utmost to help!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

logika Smart Translator WL-ZWWWDPW-0101-01 User manual

Brand
logika
Model
Smart Translator WL-ZWWWDPW-0101-01
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents