Weatherguard IS 63100 User manual

Brand: Weatherguard

Model: IS 63100

Type: User manual

Weatherguard IS 63100 is a high-quality commercial greenhouse designed to provide a protective environment for your plants. Built with a rigid frame system, it can withstand moderate wind conditions. The polyethylene roof skin and separate door and end panels ensure maximum longevity at an affordable price. The greenhouse includes a heavy-duty base plate system that can be bolted to any style of foundation. It features a front door zipper panel for easy access and a solid back panel for added protection.

COMMERCIAL GREENHOUSE

ITEM# IS 63100 12’ wide x 8’6” high x 20’ long

MATERIALS DESCRIPTON QUANITY

INCLUDED

A Curved Pipe Male/Female 18

B Curved Pipe Male/Male 6

C Long Connector Bolts/Nuts 30

D Horizontal Straight Purlins 25

E Left Hand Corner Base 2

F Right Hand Corner Base 2

G Line/Wall Base 8

H Short Connector Bolts/Nuts 12

I Yellow Safety Connector Caps 42

J Corner Base Ratchets 4

K Front Door Zipper Panel 1

L Black Bungie Balls 62

M Back Solid Panel 1

N Top Cover 1

O Top Cover Lasing Ropes 2

P Diagonal Corner Brace Rods 4

ADDITIONAL MATERIALS (NOT SUPPLIED)

·Foundation Options:

Ground Direct, Pressure-Treated Lumber

or Railroad Ties or Concrete Slab.

Note: Read Steps #1 and #2

to determine your specific needs.

IS 63100 manual

from year 2008

IMPORTANT NOTICE! PLEASE READ THESE INSTRUCTIONS

COMPLETETLY PRIOR TO ASSEMBLING YOUR STORAGE SOULUTIONS™

SHELTER!

·This high-quality Storage Solutions™ Round Top Shelter requires tie downs to serve your needs

effectively.

·A heavy-duty base plate system is supplied; and can be bolted to any style of base system.

·Carefully following Steps #1 and #2 makes the remaining Round Top Shelter assembly easy and safe.

SITE CHOICE AND GROUND PREPARATION

This Storage Solutions™ Round Top Shelter is designed with a rigid frame system, allowing it to

move in moderately windy conditions. Locating your shelter next to a natural or man-made wind

block (e.g., building, fence, trees, hedges, etc.) is beneficial in case of severe wind conditions.

FOUNDATION CHOICES

Your Storage Solutions™ Round Top Shelter includes heavy-duty plates (4 of them corner plates).

Each plate has pre-drilled bolt holes and can be bolted direct to a foundation of your choice.

It is easier to align and square the shelter foundation if you attach base plates

after assembly to a pressure-treated seal plate. The preassemble seal plate can then be anchored to

your concrete foundation, or simply lag bolted to the pressure-treated timber foundation of choice.

If the foundation of choice is a concrete slab or concrete footing, such as a house-style foundation,

pressure treated timber or railroad tie (sold separately) can also be used. However, this type of

foundation must also be permanently anchored to the ground using earth/ground anchors (sold

separately). Call our 1-800 number for questions.

Do not anchor down the second line of plates and purlins until you make sure

the two lines are square. This is easily accomplished using the diagonal measuring process. Diagonal

measurements (from corner to corner) will be the same if squared correctly. SEE DRAWING.

ASSEMBLY OF FRAMEWORK

2 people assisting with framework assembly makes the task easier and safer.

CAUTION! The Storage Solutions™ Round Top Shelter frame design is flexible. Please be aware

that overhead parts and/or pipes can come loose and fall during assembly. DO NOT allow children on

or around the assembly site when erecting your shelter. And ALWAYS pay attention overhead for

safety!

Assembly using 3 curved pipe male/female (A), and 1 curved pipe

male/male (B), along with long connector bolt (C). Do not install nuts

at this time. See photo.

Once all arches are assembled install a 49” long purlin (D) from one arch to the next in the top center

location (please do not over tighten the bolt and deform the tubing), follow the same procedure until

you have 3 complete horizontal tubing at each joint going the length of the

shelter.

Using 1 left base (E) and 1 right base (F) along with 4 line bases (G) create the left and right wall of

the shelter connecting all bases together using 49” straight purlins and long connector bolts (C). Next

install the 4 Diagonal Corner Brace Rods (P) Now set the side wall under each side of the arches and

bolt together using short connector bolts (H). You should now have the complete frame work

assembled. Please at this point you must install the yellow bolt safety connectors (I) and install a

ground anchor system, then you can move onto installing the door

panel (K), end panel (M) and top cover (N).

INSTALLING THE SOLID END PANEL AND DOOR PANEL

After determining which end will be the door and

which will be the solid panel, use the supplied elastic

cords to attach the panels to the end arches.

NOTE: When storing large items (e.g., boats, trucks, tractors, etc.),

removing the door panel will help to avoid possible damage to the door.

INSTALLING THE ROOF SKIN PANEL

The Storage Solutions™ Round Top Shelter includes a polyethylene roof skin and separate door and

panels. This design provides maximum life at a very reasonable price.

NOTE: Please take great care when handling the roof skin to prevent scratching or piercing during

installation. Place a ground tarp under the roof skin during assembly. Do not walk on the material at

any time.

Unfold the roof skin and lay it next to the bottom purlin on one side of your shelter. Center the roof

skin so approximately 6” of material extends beyond both ends of the framework. Using the supplied

lacing rope, lace the bottom edge of the roof skin through the reinforced grommets to the bottom

purlin.

Begin lacing in the middle of the skin.

Once you reach the ends, tie off lacing

on end base plates.

LACING THE GROMMETS TOO TIGHTLY CAN DAMAGE THE COVER.

NOTE: The roof skin features an outside flap sewn along the bottom.

This flap lies on the ground, eliminating gaps between the metal frame

and the ground. Now you are ready to pull the roof skin over the arch

framework. Tie ropes to the skin’s center grommet and 2 end (corner)

grommets. Keeping the roof centered, VERY CAREFULLY pull the

ropes and roof skin over the frame. See Drawing.

One person pulling each rope will keep the skin centered as it is pulled across the frame. If possible,

another person can carefully push up the underside of the roof skin to help the material pass over ridge

purlins. See Drawing.

Use caution to avoid weakening the grommets or tearing them out of the skin. Also take care not to

scratch or tear the roof skin on the framework.

Now that the roof skin is over the frame, lace the bottom grommets to the bottom purlins, starting from

the middle, as on the first side. Again, avoid over tightening lacing.

TIGHTENING THE FOUR RATCHETS ON EACH CORNER BASE PLATE

Using the four ratchets (J) supplied, install one on each corner base plate.

A flat webbing rope extends from all 4 corner of the roof skin. Insert the

webbing into the ratchets and slowly begin tightening each corner,

alternating between the 4 corner and tightening a little at a time.

As you tighten the ratchets, the 6” roof skin flap will fold over the

framework ends, helping to secure your galvanized framework together.

NOTE: The flat webbing is inside the corners of the cover you may need to reach up inside the skin

to find them.

CAUTION!: DO NOT OVERTIGHTEN THE RATCHETS! Tighten only until the skin fold over

the framework by approximately 6”. The roof material is intended to drape over the framework only –

it is not designed to be stretched. Additional ratcheting will only stretch the polyethylene material,

thinning and weakening the roof skin and potentially voiding the warranty.

NOTE: In the spring months condensation will gather inside the shelter. To avoid this from being a

problem, it would be advisable to open the door and allow your shelter to breath.

Congratulations! You now have a completed high-quality Weatherguard™ Commercial

Greenhouse.

ONE LAST HINT! If you ever disassemble your Weatherguard™ Commercial

Greenhouse, clean and dry the skin completely before storing to prevent mildew, which can rot the

polyethylene. Always use caution when disassembling overhead framework!

All of us at Jewett-Cameron thank you for purchasing our products.

For product information, replacement parts and customer service,

Call us toll-free 800-955-2879

E-Mail [email protected]

Ask about other quality Jewett-Cameron products:

Weatherguard™ Deck/Patio Greenhouse

Lucky Dog™ Modular Dog Run

Lucky Dog™ Easy-Ship Boxed Kennel

Weatherguard™ Kennel Cover

PLEASE READ THIS WARRANTY CAREFULLY TO INSURE YOUR RIGHTS

LIMITED EXPRESS WARRANTY

Jewett-Cameron warranties your Storage Solutions™ Include your return address and phone number,

Shelter to be free of defects in material and workmanship and and a copy of the original invoice or further

Further warrants that, in normal use, the Storage Solutions™ proof of the date of purchase, plus a description

Shelter is waterproof, will not tear, and will not be affected by of the claimed defect. ALL IMPLIED

mildew. This warranty is extended to the first retail purchaser of WARRANTIES, INCLUDING BUT NOT

the Shelter for consumer use, and lasts for one (1) year from the LIMITED TO IMPLIED. WARRANTIES OF

date of purchase. Jewett-Cameron will replace any cover that MERCHANTABILITY AND FITNESS FOR

is defective (unless those defects result from abuse or misuse of PARTICULAR PURPOSE, ARE LIMITED IN

the cover, such as puncture or damage caused by excessive wind DURATION TO ONE (1) YEAR FROM THE

or heat). The replacement will be without charge to you, if you DATE OF PURCHASE. Some states do not

notify Jewett-Cameron in writing within the first six (6) months allow limitations on how long an implied

after date of purchase, but before the expiration of this Warranty, warrant lasts, so the above limitations may not

Jewett-Cameron will provide you with a replacement cover for apply to you. This Warranty gives you specific

50% off its then-current retail price. Jewett-Cameron WILL NOT legal right, and you may also have other rights

HAVE OTHER OR GREATER LIABILITY FOR DEFECTS IN which may vary from state to state.

THE COVER, NOR WILL JEWETT-CAMERON HAVE ANY

INCIDENTIAL OR CONSEQUENTIAL DAMAGES. Some

States do not allow the exclusions or limitations of incidental

or consequential damages, so the above limitation or exclusion THIS PRODUCT IS NOT SOLD OR INTENDED

may not apply to you. If you discover a defect in the cover FOR USE AS A FLAME RETARDANT ARTICLE:

during the warranty period, and wish to obtain a replacement, this product can be burned and under some conditions

send notice of your claim to: may continue to burn once ignited. This product meets

the flammability requirements of commercial standards

Jewett-Cameron CS-192-53 (paragraph 4.10) for general purposes vinyl

P.O. Box 1010 plastic film to which the Flammable Fabrics Act, Public

North Plains, OR 97133 law 88 refers. Storage Solutions™ Shelters, unless

Specifically labeled for such use, do not meet the

flammability standards for use as tent material.

Weatherguard IS 63100 User manual

Brand: Weatherguard

Model: IS 63100

Type: User manual

Download PDF

report

Weatherguard IS 63100 User manual

Weatherguard IS 63100 User manual

Related papers

Other documents