SURVIVE-A-STORM XP0D04 Shelters ShelterCube Hovel User manual

Brand
SURVIVE-A-STORM
Model
XP0D04 Shelters ShelterCube Hovel
Type
User manual

SURVIVE-A-STORM XP0D04 Shelters ShelterCube Hovel is a storm and tornado safe shelter that can be installed in a variety of locations, including homes, schools, and businesses. The shelter is made of high-strength steel and is designed to withstand winds of up to 250 mph. It is also waterproof and airtight, making it an ideal place to shelter from storms, tornadoes, and other emergencies.

The ShelterCube Hovel is easy to install and can be assembled by two people in less than an hour. It comes with all of the necessary hardware and instructions. The shelter is also portable, so it can be moved to a new location if needed.

SURVIVE-A-STORM XP0D04 Shelters ShelterCube Hovel is a storm and tornado safe shelter that can be installed in a variety of locations, including homes, schools, and businesses. The shelter is made of high-strength steel and is designed to withstand winds of up to 250 mph. It is also waterproof and airtight, making it an ideal place to shelter from storms, tornadoes, and other emergencies.

The ShelterCube Hovel is easy to install and can be assembled by two people in less than an hour. It comes with all of the necessary hardware and instructions. The shelter is also portable, so it can be moved to a new location if needed.

TwisterPod Installation Instructions
1 - Determine the location to install the shelter. e concrete slab it is to be installed on must be free of major cracks and defects that could
compromise the foundation. It is imperative that the foundation meet the engineered specifications. e concrete used in the foundation must
be a minimum of 2500 psi concrete. is is generally the minimum psi concrete available, and most concrete is 3000 psi plus by code. If there
is doubt about the concrete, consult a local concrete company for testing.
e minimum foundation sizes for the 4’ round TwisterPod model shelter are as follows:
4’’ thick (nominal) 13’-6’’ x 11’-6’’ | 6’’ thick (nominal) 11’-9’’ x 9’-9’’ | 24’’ thick 5’x5’
e minimum distance an anchor bolt can be from the edge of foundation is 4’’.
2 - Unbolt the shelter from the inside to remove it from the skid. en, with a pallet jack, forklift, tractor, etc., place the shelter in it’s desired
location. You will notice a total of 24 holes in the bottom interior and bottom exterior flange of the TwisterPod shelter. You will only need to use
12 of the 24 holes, either all inside, all outside, or alternating between inside and outside. After the shelter is in the desired location, use a
hammerdrill with a ’’ masonry bit to drill through the holes in the shelters bottom flange.
Drill the holes to approximately 3-¼’’ deep into the concrete. (most hammer drills have a depth guide that can be set to a desired depth). Do not
drill too deep. If a vacuum is available use it to remove the debris from the drilling process, if not then just sweep it out of the way before
installing the anchors.
3 - Take the provided anchors, washers, and nuts and place one flat washer
on each anchor and then thread the nut on until it is about flush with the
top of anchor. Put the anchor into each of the 12 holes and tap completely
in with a hammer.
4 - Use a torque wrench and ’’ socket to torque the anchors to 25 lbs/ft.
After torqueing all anchors it is recommended to repeat the torque process
a second time to insure that all anchors are to 25 lbs/ft.
5 - Remove the Lifting eyelet from the roof of the shelter and replace it
with the provided ’’ bolt and washer. is is done to eliminate leaking
if the shelter is placed outside in the elements.
1 ” Bolt x 1
” Washer x 1
” Washer x 12
” Nut x 12
“ Wedge x 12
Hardware Included Tools Needed
Hammer
” Socket & Ratchet
” Masonry Bit
Hammer Drill
We’re always working to make things better for you. If you have feedback about this manual, please tell us at survive-a-storm.com/feedback
  • Page 1 1

SURVIVE-A-STORM XP0D04 Shelters ShelterCube Hovel User manual

Brand
SURVIVE-A-STORM
Model
XP0D04 Shelters ShelterCube Hovel
Type
User manual

SURVIVE-A-STORM XP0D04 Shelters ShelterCube Hovel is a storm and tornado safe shelter that can be installed in a variety of locations, including homes, schools, and businesses. The shelter is made of high-strength steel and is designed to withstand winds of up to 250 mph. It is also waterproof and airtight, making it an ideal place to shelter from storms, tornadoes, and other emergencies.

The ShelterCube Hovel is easy to install and can be assembled by two people in less than an hour. It comes with all of the necessary hardware and instructions. The shelter is also portable, so it can be moved to a new location if needed.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents