Pairing TomTom Remote LINK
1
Pairing TomTom Remote LINK
You need to pair your TomTom Remote LINK with a TomTom LINK 300/310
before you first use the device. This is required because the Remote LINK
transmits your input to the LINK 300/310 without saving the information.
There are two ways to pair your Remote LINK with the LINK 300/310 which are
described in this document. TomTom WORK certified sales partners can also
use the activation tool, visit www.tomtomwork.com/activationtool
Important: A Remote LINK can only be paired with one LINK 300/310. If your
Remote LINK or the LINK 300/310 has already been paired with another
device, both devices need to be reset before pairing with a new device.
Instructions on how to reset both devices are described in this document.
Pairing Remote LINK to LINK 300/310
You can pair the Remote LINK with a LINK 300/310 by only using the two
devices.
1. Make sure the LINK 300/310 is properly installed in the vehicle.
2. Switch on the ignition.
3. Make sure there are no other vehicles installed with a LINK 300/310 located
within a distance of 30 metres.
4. Press any button on your Remote LINK to switch it on.
If the LEDs on all three buttons are flashing, then the device is not paired
and you need to continue with the next step. Otherwise reset your Remote
LINK.
5. Press any two buttons at the same time until you hear a sound.
Remote LINK starts searching for your LINK 300/310 and the blue
Connection LED begins to flash rapidly. Searching may take about one
minute before a connection is established.
Note: To check if a connection has been established press any key.
2
If a connection is established, the blue Connection LED will be on. If you do
not use your Remote LINK for 15 seconds, the device will switch off.
If no connection is established, the yellow LEDs on all three buttons will flash
and after one minute, the Remote LINK will switch off.
To establish a connection, repeat steps 1 to 4.
3
Assigning a Bluetooth address via TomTom WEBFLEET
You can assign a Bluetooth address for the connection between a Remote
LINK and a LINK 300/310 using TomTom WEBFLEET. This ensures a unique
identification for every connection, helping to avoid pairing errors.
Requirement: You need access to TomTom WEBFLEET.
1. In TomTom WEBFLEET select the corresponding vehicle under "Vehicles"
and click "Configure" in the details panel on the right.
2. Select the "Accessory" tab.
3. Enter the Bluetooth address of the Remote LINK, in the field for Bluetooth
address.
4. Switch on the Remote LINK by pressing any key.
The yellow LEDs on all three buttons should begin to flash. If not, the
Remote LINK needs to be reset. For instructions on resetting the device,
read ’Resetting TomTom Remote LINK’.
5. Switch on the ignition.
The devices start to pair and the blue LED begins to flash. Pairing may take
up to one minute.
Note: To check if a connection is established, press any key.
If a connection is established, the blue Connection LED will be on. If you do
not use your Remote LINK for 15 seconds, the device will switch off.
4
If a connection is not established, the yellow LEDs on all three buttons will
flash and after one minute, the Remote LINK will switch off.
To establish a connection, repeat steps 1 to 5.
5
Resetting TomTom Remote LINK
If your Remote LINK is paired with a device but not working properly, or if your
Remote LINK is paired with the wrong device, you can reset the device to the
default factory settings.
1. Press any button on your Remote LINK to switch it on.
2. Press any two buttons at the same time until you hear a sound.
Your Remote LINK switches off.
Note: To check if the reset was successful, press any key on your Remote LINK
to switch it on.
If the yellow LEDs on all three buttons are flashing, then the reset was
successful.
If the blue Connection LED is on, then the reset was not successful.
To reset your Remote LINK, repeat steps 1 to 2.
Resetting TomTom LINK 300/310
If you want to pair your LINK 300/310 to a different Remote LINK, you need to
reset the LINK 300/310. To reset the LINK 300/310, delete the Bluetooth
address for the Remote LINK for the corresponding vehicle in the
configuration dialogue in TomTom WEBFLEET and click "Save changes".
-
1
-
2
-
3
-
4
-
5
TomTom LINK 310 User manual
- Category
- Bluetooth music receivers
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
TomTom PRO 4KI00 User manual
-
-
-
-
TomTom Pro 5150 Truck LIVE User manual
-
-
-
-
-
