Ohlins POF3A00 Mounting Instruction
- Category
- Car kits
- Type
- Mounting Instruction
This manual is also suitable for
Mounting Instructions
Öhlins suspension kit POF 3A00, 3A0, 4A00, 4A0
for Porsche 996 GT3R-RS rear strut
© Öhlins Racing AB. All rights reserved. Any reprinting or unauthorized use without the
written permission of Öhlins Racing AB is prohibited. Printed in Sweden.
Öhlins heavy duty suspension type 46HRC
Your new Öhlins suspension features a hose connected
reservoir. The suspension has the following adjusters:
Compression damping:
Adjustments are made with the knob on the hose con-
nected reservoir.
Rebound damping adjustments:
Adjuster is at the bottom of the strut: Use a 3 mm allen
key.
Spring pre-load:
Adjustments are made with adjustment rings on the strut
casing. Use the c-spanners
When delivered the Öhlins suspension is dialled to rec-
ommended settings for the specific brand and make of
the vehicle.
NOTE!
If you have turned the adjuster without counting the
number of clicks you must go back to the recommended
settings. Close the adjuster and count the clicks when
turning it counter-clockwise.
CAUTION!
Using too much force when closing the adjusters will
destroy important sealing surfaces.
NOTE!
US only: POF 3A01 and POF 4A01 are delivered with-
out spring.
Compression
damping adjuster
Spring
pre-load
adjuster
Rebound damping
adjuster
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00. Fax +46 8 590 025 80
www.ohlins.com
POF 3A00, 3A01, 4A00, 4A01, Issued 05 05 18
Setting up your car:
Set ride height, camber angles and toe in.
Spring preload:
Distance between cylinder
head and spring lock nut: 69 mm in
basic setting.
Compression clicks: 8
(from closed position)
usable range approx. 0-25 clicks
Rebound clicks: 26
(from closed position)
usable range approx. 5-35 clicks
For adjustment and maintenance instructions,
see Owners manual.
8
Fit the shock absorber to the car. First fit the up-
per mounting, then the lower mounting bolt and
tighten them. For tightening torque see the car´s
owners manual. Check that the hose banjo is
pointing backwards.
9
Fit the reservoir bracket to the fender. Use the
sheet metal screws provided.
10
Position the reservoir in the bracket and tighten
the camp. Do not overtighten.
11
Reassemble the anti roll bar.
CAUTION!
The hose must not be restricted and should run
in soft turns.
NOTE!
Make sure that all bolts are tightened to the correct
torque and that nothing fouls or restricts movement
of the suspension when it is being fully compressed
or extended.
12
Continue your work accordning to Owners
manual, section adjustments.
9
Before installation
Öhlins Racing AB can not be held responsible
for any damage whatsoever to suspension
components or vehicle, or injury to persons, if
the instructions for fitting and maintenance are
not followed exactly.
Similarly, the warranty will become null and void
if the instructions are not adhered to.
WARNING!
1. Installing suspension components, that is
not approved by the vehicle manufacturer,
may affect the stability of your vehicle. Öhlins
Racing AB cannot be held responsible for
any personal injury or damage whatsoever
that may occur after fitting the suspension
components. Contact an Öhlins dealer or
other qualified person for advice.
2. Please study and make certain that you
fully understand all the mounting instructions
and the owners manuals before handling this
suspension components kit. If you have any
questions regarding proper installation
procedures, contact an Öhlins dealer or other
qualified person.
3. The vehicle service manual must be
referred to when installing the Öhlins
suspension components
Safety signals
Important information concerning safety is
distinguished in this manual by the
following notations:
The Safety alert symbol means:
Caution! Your safety is involved.
WARNING!
Failure to follow warning instructions
could result in severe or fatal injury
to anyone working with, inspecting or
using the suspension, or to bystanders.
CAUTION!
Caution indicates that special
precautions must be taken to avoid
damage to the suspension.
NOTE!
This indicates information that is of
importance with regard to procedures.
Öhlins products are subject to continual improve-
ment and development. Consequently, although
these instructions include the most up-to-date
information available at the time of printing, there
may be minor differences between your
suspension and this manual. Please consult your
Öhlins dealer if you have any questions with
regard to the contents of the manual.
NOTE!
During storage and transportation, especially
at high ambient temperature, the oil and
grease used for assembling may run out
inside the packing and damage the expanded
polystyrene packing material. This is not
unusual and is in no way detrimental to the
suspension components.
Kit contents
Before installing the suspension components,
please check the contents of the kit, listed on
the front page of this instruction. If anything is
missing, contact your Öhlins dealer.
Description Part No. Pcs.
Shock absorber left rear POF 3A00 1
Shock absorber right rear POF 3A01 1
Shock absorber left rear POF 4A00 1
Shock absorber right rear POF 4A01 1
Reservoir bracket assembly 2
Sheet metal screws 05389-01 4
Spacer 05688-01 2
C-spanner 00710-02 2
Sticker 00192-01 4
Sticker 00197-02 4
Owners manual 1
69 mm
5
6
WARNING!
1. It´s advisable to have an Öhlins dealer or other
qualified person to fit your shock absorber.
2. Instructions in the vehicle service manual are
to be followed when changing the shock ab-
sorber.
3. When working on a lifted vehicle it must be
securely supported to prevent it from falling.
Mounting instructions
1
Lift the car so the rear wheels are clear of the
ground. Make sure it´s steadily fixed so it will not
fall down.
2
Loosen the anti roll bar from the original shock
absorbers.
3
Remove the standard shock absorbers. First
loosen the lower mounting bolt and then the up-
per mount (three nuts). Remove the upper mount
and the sway bar bracket from the shock ab-
sorbers. See the car´s work shop manual.
NOTE!
Check the position of the anti roll bar bracket, so
it can be fitted to the Öhlins shock absorber in
the same way.
4
Check the marking on the Öhlins rear shock ab-
sorber to locate left or right rear.
5
Remove the top nut, the spacers, washer and
springs from the Öhlins strut. Remove the adjust-
ment ring and the two lock nuts. Fit the anti roll
bar bracket to the shock absorber by treading it
on and fix it in position with a lock nut.
CAUTION!
Make sure that the suspension can move through
its entire stroke without causing binds in the anti
roll bar attachments.
6
Reassemble the shock absorber. The distance
between the cylinder head and the spring lock
nuts should be 69 mm.
7
Fit the original upper mounting/bearing to the
Öhlin shock absorber. The original spacer on the
lower side of the mount should be used together
with the supplied spacers on the upper side of
the mount. See fig. below how to apply the
spacers. Tightening torque 65 Nm
Original
upper
mount
Original
anti roll
bar bracket
7
-
1
-
2
Ohlins POF3A00 Mounting Instruction
- Category
- Car kits
- Type
- Mounting Instruction
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ohlins MIS8A00 Mounting Instruction
-
-
-
-
-
-
-
-
-