LG SMART TV
1
1 CONNECTING TO A WIRED/WIRELESS NETWORK
Wired Network Connection Wireless Network Connection
➊
Wireless network connection: If your model does not have Wi-Fi built-in, you will need an LG wireless
dongle. (Read the Owner's Manual to fi nd out your TV's Wi-Fi capability.)
➋ If you have an operational wall-mounted Internet connector, you can connect it directly to your TV via a
LAN cable, without using a router. (Using DLNA or Media Links will require a wired/wireless router.)
2 CONFIGURING A TV NETWORK (WIRED/WIRELESS CONNECTION)
(For wired connection, follow steps A→E→F.)
AV MODE INPUT
TV/
RAD
ENERGY
LIST
Q.VIEW
FAV
3D
MUTE
MARK
P
P
A
G
E
SAVING
BACK
EXIT
OK
Q.MENU
Home
1 2
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PQRS
8
TUV
0
9
WXYZ
CHAR/NUM
DELETE
3D OPTION
Premium
REC
LIVE TV
INFO
RATIO
AV MODE INPUT
TV/
RAD
ENERGY
LIST
Q.VIEW
FAV
RATIO
MUTE
MARK
P
P
A
G
E
SAVING
BACK
EXIT
OK
Q.MENU
Home
1 2
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PQRS
8
TUV
0
9
WXYZ
CHAR/NUM
DELETE
Premium
GUIDE
REC
LIVE TV
INFO
LZ9600/LW9500/LW7700/LW6500/LW5700 LV5500/LV3700/LV370S
GUIDE
SMART TV
SMART TV
SETUP
NETWORK Network Setting
Press the Home button on the remote con-
trol to select the network type you want.
3 IMPROVING WIRELESS RECEPTION
➊
Change the router’s wireless channel or check that the security option is enabled.
If the security option is disabled, the network can be interrupted by other devices resulting in decreased
speed. (See the router manufacturer’s website to fi nd out how to change the router channel and enable
security settings.)
➋
Check that the wireless signal is not receiving interference. Keep the router and the TV close to each
other.
WallStudy Living room
Reduced
sensitivity
➌
You can increase the network sensitivity further by positioning the wireless dongle closer to the router
using a USB extension cable (sold separately).
4 TROUBLESHOOTING NETWORK PROBLEMS
Follow the instructions below that correlate to your network status.
Check the TV or the router.
Network Status
█ When an X appears between TV and Gateway.
① Check the cable connection between the TV and the wired/wireless router.
② Reset the power for both the TV and the router/cable modem.
③ If you use a fi xed IP address and choose to set the IP address automatically, an X will appear
between TV and Gateway.
④ If you are not using a router, consult your Internet service provider for service.
<Additional points to check when using a wireless connection>
① Check the password for the wireless connection in the router settings window.
② Change the router SSID (network name) or the wireless channel.
Check the router or consult your Internet service provider.
Network Status
█ When an X appears between Gateway and DNS.
① Check the router/cable modem.
- Unplug the router/cable modem, then plug it back in after 5 seconds.
- Press the Reset button on the router/cable modem.
② If you are not using a router, consult your Internet service provider.
Network Status
█ When an X appears between DNS and Internet.
① Unplug the router/cable modem, then plug it back in after 5 seconds.
② Press the Reset button on the router/cable modem.
③ Check that the MAC address of the TV/router is registered with your Internet service provider.
(The MAC address displayed on the right pane of the network status window should be regis-
tered with your Internet service provider.)
④ Check the router manufacturer’s website to make sure your router has the latest fi rmware ver-
sion installed.
LG SMART TV NETWORK (INTERNET CONNECTION)
SETTINGS
TV
Gateway
DNS
Internet
TV
Gateway
DNS
Internet
TV
Gateway
DNS
Internet
P/NO: MBM37745536 (1106-REV00)
(Image shown may differ from your TV.)
A. Select either Wired or
Wireless to set the network
type.
B. When you choose to use a
wireless network, select
Setting from the AP list.
C. Select the wireless router
to connect to.
NETWORK
OK
Move
• Network Setting : Wired
• Network Status : Internet is connected
• Smart TV Setting
• Legal Notice
Exit
• Network Setting : Wired
Network Type
Wired network is recommended
Wired
Wireless
Close
Selecting the wireless network setting type
Select the wireless network setting type.
Setting from the AP list
Simple setting (WPS-button mode)
Setting Ad-hoc network
ꕉ Previous ꕯ Exit
ꔉ Next
Selecting AP
Previous
Exit
Select AP you want to connect.
Page 1/1
Input the new SSID
iptime
ASW
Network1
PIN Connect
Access Point
Search
D. For wireless routers that have
the ꔒ symbol, you need to
enter the security key.
E. IP and DNS addresses are
automatically confi gured
for home users. If you
have not changed any
router settings, just press
the enter button twice.
F. The ꔐ symbols indicate
that the network is connect-
ed properly at each step.
Inserting the security key
◄ ►
OK
Cancel
Exit
ꕉ Previous
Insert 8~63 ASCII characters
Network Setting
IP Mode
IP Auto Setting
● IP Address 0 . 0 . 0 . 0
● Subnet Mask
255 . 255 . 0 . 0
● Gateway 0 . 0 . 0 . 0
DNS Mode
DNS Auto Setting
● DNS Server 0 . 0 . 0 . 0
OK
Exit
ꕉ Previous
◄ ►
◄ ►
Network Status
Auto mode
Wired network is connected.
MAC Address : E8:5B:5B:39:C0:E4
IP Address : 192.168.100.31
Subnet Mask : 255.255.255.0
Gateway : 192.168.100.1
DNS Server : 164.124.101.2
Setting Test Close
TV
Gateway
DNS
Internet
RS-232C IN (CONTROL&SERVICE)
IN 1(ARC) IN 2 IN 3 IN 4
LAN
RGB IN (PC)
OPTICAL DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
ANTENNA/
CABLE IN
AV IN 2
AUDIO / VIDEO
COMPONENT IN 2
AUDIO / Y P
B
P
R
H/P
WIRELESS
CONTROL
AUDIO
VIDEO
L/MONO
R
AV IN 1
COMPONENT
IN 1
AUDIO
RL
Y
P
B
P
R
VIDEO
/DVI /DVI /DVI /DVI
HDD IN
USB IN 1
USB Apps
USB IN 2
INPUT
HOME
P
OK
H
INPUT
HOME
H
OK
P
Internet connection
Wired router
RS-232C IN (CONTROL&SERVICE)
IN 1(ARC) IN 2 IN 3 IN 4
LAN
RGB IN (PC)
OPT ICAL DIGITAL
AUD IO OUT
AUDIO IN
(RGB/DVI)
ANTENNA/
CABLE IN
AV IN 2
AUDIO / VIDEO
COMPONENT IN 2
AUDIO / Y PB PR
H/P
WIRELESS
CONTROL
AUDIO
VIDEO
L/MONO
R
AV IN 1
COMPONENT
IN 1
AUDIO
RL
Y
P
B
P
R
VIDEO
/DVI /DVI /DVI /DVI
HDD IN
USB IN 1
USB Apps
USB IN 2
INPUT
HOME
P
OK
H
INPUT
HOME
H
OK
P
Internet connection
Wired/wireless router
LG wireless
dongle