Sonifex Redbox RB-MA1 Mic Preamp Owner's manual

Redbox

User Handbook No3

Mixers & Source Selectors, Microphone

Ampliﬁers, Stereo to Mono Converters,

General Interfaces

RB-SS10 10 way stereo analogue source selector/mixer

RB-DSS10 10 way stereo digital source selector

RB-PMX4 10 input, 4 output analogue preset mixer (1U)

RB-SSML1 Mic/line source selector with compressor/limiter

RB-MA1 Microphone ampliﬁer, single

RB-MA2 Microphone ampliﬁer, dual

RB-DMA2 Dual digital microphone ampliﬁer

RB-ML2 Microphone limiter, 2 channel

RB-SL2 Twin mono, or stereo limiter

RB-SM1 Stereo to mono converter, single

RB-SM2 Stereo to mono converter, dual

RB-LC3 3 way light/power controller

RB-MM1 Mix minus generator

b

Redbox User Handbook No 3

Revision 1.00 October, 2006

©Sonifex Ltd, 2000-6

Sonifex Ltd, 61, Station Road, Irthlingborough,

Northants, NN9 5QE, England.

Tel : +44 (0)1933 650 700

Fax : +44 (0)1933 650 726

Email : [email protected]o.uk or technical.suppor[email protected]o.uk

Web : http://www.sonifex.co.uk

Information in this document is subject to change without notice and does not represent

a commitment on the part of Sonifex Ltd. Sonifex Ltd shall not be liable for any loss or

damage whatsoever arising form the use of information or any error contained in this

manual.

No part of this manual may be reproduced or transmitted in any form or by any means,

electronic or mechanical, including photocopying, recording, or information storage and

retrieval systems, for any purpose other than the purchaser’s personal use, without the

express written permission of Sonifex Ltd.

Unless otherwise noted, all names of companies, products and persons contained herein are

part of a completely ﬁctitious adaptation and are designed solely to document the use of

Sonifex products.

Redbox User Handbook No 3

c

CONTENTS

Warranty i

Warranty and Liability - important the purchaser is advised to read this clause i

Unpacking the Redbox ii

Returning the Warranty Card iii

Safety Information iii

Safety of Mains Operated Equipment iii

Voltage Setting Checks iii

Fuse Rating iii

Power Cable and Connection iv

Ordering the Correct Mains Lead iv

Installation Information iv

Atmosphere iv

Electromagnetic Radiation iv

Fitting Redboxes iv

WEEE & RoHS Directives - Sonifex Statement vi

1 RB-SS10 10 Way Stereo Analogue Source Selector/Mixer 1

Introduction 1

System Block Diagram 2

Front Panel Indicators & Controls 2

Illuminated Push Buttons 2

Front Panel Gain Controls 3

Headphone Output 3

Volume Control 3

Additional Modes 3

Conﬁguring the Additional Modes 3

Rear Panel Connections and Operation 4

Inputs 4

Outputs 4

Altering the Master Output Level 4

RB-SS10 Additional Audio Input Connectors 5

RB-SS10 Remote Start I/O 6

Remote Select/Switch Inputs 7

Status Outputs 8

Technical Speciﬁcations RB-SS10 9

2 RB-DSS10 10 Way Stereo Digital Source Selector 11

Introduction 11

System Block Diagram 12

Front Panel Indicators & Controls 12

Power Indicator 13

Illuminated Push Buttons 13

Headphone Output 13

Volume Control 13

Additional Modes 13

Conﬁguring the Additional Modes 13

Rear Panel Connections and Operation 14

RB-DSS10 Inputs 14

AES/EBU Inputs 14

RB-DSS10 Outputs 14

AES/EBU Outputs 14

Digital Audio Inputs & S/PDIF Output 15

Remote Start I/O 15

Remote Select/Switch Inputs 17

Status Outputs 18

Technical Speciﬁcations RB-DSS10 19

d

Redbox User Handbook No 3

CONTENTS

3 RB-PMX4 10 Input, 4 Output Analogue Preset Mixer 21

Introduction 21

System Block Diagram 22

Rear Panel Connections and Operation 22

Outputs 1-4 23

Front Panel Controls 23

Switch Banks 23

Input Gain Controls 23

Technical Speciﬁcations RB-PMX4 24

4 RB-SSML1 Mic/Line Source Selector with Compressor Limiter 25

Introduction 25

System Block Diagram 26

Rear Panel Connections 26

Stereo Monitor Input 27

Stereo Monitor Pad & Volume Control 27

Mic Input 27

Mic Input Gain 27

Using Phantom Powered Microphones 27

Using the LF Filter 28

Compression Active on Mic Input Only 28

Peak Hold Disabled on LED Meter 28

Stereo Line Input 28

Stereo Input Gain Pad 28

Stereo Line Output 28

Front Panel Controls 28

Mic & Line Volume Controls 28

Mic/Line Select Switch 29

Bypass Button 29

Applying Compression 29

LED Metering 29

Headphone Outputs 29

Technical Speciﬁcations RB-SSML1 30

5 RB-MA1 Single & RB-MA2 Dual Microphone Ampliﬁers 31

Introduction 31

System Block Diagram 31

Rear Panel Connections and Operation 32

Mic Inputs 32

Input Gain 32

Using Phantom Powered Microphones 33

Using the LF Filter 33

Output 33

Technical Speciﬁcations RB-MA1 & RB-MA2 34

6 RB-DMA2 Dual Digital Microphone Ampliﬁer 35

Introduction 35

System Block Diagram 36

Front Panel Indicators & Controls 36

Sync & Power Indicator 37

Input Level Adjustment 37

Disabling the Fine Gain Control Knob 37

Input Level Indicators 37

Rear Panel Connections and Operation 37

RB-DMA2 Inputs 38

Mic Inputs 38

Word Clock Sync Input 38

Redbox User Handbook No 3

e

CONTENTS

S/PDIF Sync Input 38

RB-DMA2 Outputs 38

AES/EBU Output 38

S/PDIF Output 38

Analogue Line Outputs 38

Rear Panel Controls 39

Status Select Switches 39

Output Routing 39

Phantom Power & LF Filter 39

Digital Sync & Output Select Buttons 40

Frequency and Sync Mode Rotary Switch 40

Test/Calibration Mode 41

Technical Speciﬁcations RB-DMA2 42

7 RB-ML2 Stereo Microphone & Line Level Limiter 44

Introduction 44

System Block Diagram 45

Rear Panel Connections and Operation 45

Mic / Line Inputs 46

Mic Input Gain 46

Using Phantom Powered Microphones 46

Using the LF Filter 46

Mic / Line Outputs 46

Mic / Line Output Gain 47

Level Limiting 47

Mode Select Switch 47

Technical Speciﬁcations RB-ML2 48

8 RB-SL2 Twin Mono, or Stereo, Limiter 50

Introduction 50

System Block Diagram 50

Rear Panel Connections and Operation 51

Outputs 51

Inputs 51

Gain Control 51

Mode Switch 51

Technical Speciﬁcations RB-SL2 52

9 RB-SM1 Single & RB-SM2 Dual Stereo To Mono Converter 53

Introduction 53

System Block Diagram 53

Rear Panel Connections and Operation 54

Stereo Inputs 1 (& 2) 55

Mono Output 1 (& 2) 55

Output Gain 55

Technical Speciﬁcations RB-SM1 & RB-SM2 56

10 RB-LC3 3 Way Light/Power Controller 57

Introduction 57

System Block Diagram 58

Rear Panel Connections and Operation 58

Switched Mains Outputs 59

Telephone Connections 59

Remote External Control Inputs 59

Conﬁguration Switches 60

Flash Rate Preset Potentiometer 62

Technical Speciﬁcations RB-LC3 63

f

Redbox User Handbook No 3

CONTENTS

11 RB-MM1 Mix Minus Generator 64

Introduction 64

System Block Diagram 64

Front Panel Indicator 65

Rear Panel Connections and Operation 65

Stereo Inputs From Mixer Main Output 65

Input From Mixer Telephone Fader 65

Output Null Adjustments (LF and Full-Band) 65

Band Pass Filter Switch 66

Output to Telephone Balance Unit (TBU) 66

Output Level Adjustment 66

Operation of the RB-MM1 66

Technical Speciﬁcation RB-MM1 67

Redbox User Handbook No 3

g

FIGURES

Figures

Fig A: Packing List. ii

Fig B: Fuse Rating Table. iii

Fig C: Mains Cable Wire Colours iv

Fig D: Mains Lead Table. iv

Fig E: RB-RK1Small Redbox Front Rack-mount Kit . v

Fig F: RB-RK2 Small Redbox Rear Rack-mount Kit. v

Fig G: RB-RK3 Large Redbox Rear Rack-mount Kit. v

Fig 1-1: RB-SS10 Front Panel. 1

Fig 1-2: RB-SS10 System Block Diagram. 2

Fig 1-3: RB-SS10 Front Panel. 2

Fig 1-4: RB-SS10 Rear Panel. 4

Fig 1-5: Analogue Audio Inputs Pin Connections 5

Fig 1-6: Remote Start Pin Connections. 6

Fig 1-7: Connection Example. 7

Fig 1-8: Remote Select/Switch Input Connections. 7

Fig 1-9: Connection Example. 8

Fig 1-10: Status Output Pin Connections. 8

Fig 1-11: Connection Example. 9

Fig 2-1: RB-DSS10 Front Panel. 11

Fig 2-2: RB-DSS10 System Block Diagram. 12

Fig 2-3: RB-DSS10 Front Panel. 12

Fig 2-4: RB-DSS10 Rear Panel. 14

Fig 2-5: Digital Audio Inputs and S/PDIF Output Pin Connections. 15

Fig 2-6: Remote Start Pin Connections. 16

Fig 2-7: Connection Example. 17

Fig 2-8: Remote Select/Switch Input Connections. 17

Fig 2-9: Connection Example. 17

Fig 2-10: Status Output Pin Connections. 18

Fig 2-11: Connection Example. 18

Fig 3-1: RB-PMX4 Front Panel . 21

Fig 3-2: RB-PMX4 Block Diagram. 22

Fig 3-3: RB-PMX4 Rear Panel. 22

Fig 3-4: RB-PMX4 Front Panel Controls. 23

Fig 4-1: RB-SSML1 Front Panel. 25

Fig 4-2: RB-SSML1 Block Diagram. 26

Fig 4-3: RB-SSML1 Rear Panel. 26

Fig 4-4: DIP Switch to Control Mic & Meter Features. 27

Fig 4-5: RB-SSML1 Front Panel. 28

Fig 5-1: RB-MA1 & RB-MA2 Front Panel. 31

Fig 5-2: RB-MA1 & RB-MA2 Block Diagram Single Channel. 31

Fig 5-3: RB-MA1 Rear Panel. 32

h

Redbox User Handbook No 3

FIGURES

Fig 5-4: RB-MA2 Rear Panel. 32

Fig 5-5: Switch to Control LF Filter and Phantom Power. 33

Fig 6-1: RB-DMA2 Front Panel. 35

Fig 6-2: RB-DMA2 System Block Diagram. 36

Fig 6-3: RB-DMA2 Front Panel. 36

Fig 6-4: Jumpers to Disable Fine Gain Control. 37

Fig 6-5: RB-DMA2 Rear Panel. 37

Fig 6-6: RB-DMA2 Status Select Switches. 39

Fig 6-7: RB-DMA2 Frequency and Sync Rotary Switch Selections. 41

Fig 7-1: RB-ML2 Front Panel. 44

Fig 7-2: RB-ML2 Block Diagram. 45

Fig 7-3: RB-ML2 Rear Panel. 45

Fig 7-4: Switch to Control LF Filter and Phantom Power. 46

Fig 8-1: RB-SL2 Front Panel. 50

Fig 8-2: RB-SL2 Block Diagram. 50

Fig 8-3: RB-SL2 Rear Panel. 51

Fig 9-1: RB-SM1 & RB-SM2 Front Panel. 53

Fig 9-2: RB-SM1 & RB-SM2 Block Diagram Single Channel. 53

Fig 9-3: RB-SM1 Rear Panel.. 54

Fig 9-4: RB-SM2 Rear Panel. 54

Fig 10-1: RB-LC3 Front Panel. 57

Fig 10-2: RB-LC3 Block Diagram. 58

Fig 10-3: RB-LC3 Rear Panel 58

Fig 10-4: Output 1 Conﬁguration Setting. 60

Fig 10-5: Output 2 Conﬁguration Settings. 61

Fig 10-6: Output 3 Conﬁguration Settings. 62

Fig 11-1: RB-MM1 Front Panel. 64

Fig 11-2: RB-MM1 System Block Diagram. 64

Fig 11-3: RB-MM1 Rear Panel. 65

Redbox User Handbook No 3

i

Warranty

Warranty and Liability - important the purchaser is advised to read this clause

(a) The Company agrees to repair or (at its discretion) replace Goods which are found to

be defective (fair wear and tear excepted) and which are returned to the Company

within 12 months of the date of despatch provided that each of the following

are satisﬁed:

(i) Notiﬁcation of any defect is given to the Company immediately upon its

becoming apparent to the Purchaser;

(ii) The Goods have only been operated under normal operating conditions and

have only been subject to normal use (and in particular the Goods must have

been correctly connected and must not have been subject to high voltage or

to ionising radiation and must not have been used contrary to the Company’s

technical recommendations);

(iii) The Goods are returned to the Company’s premises at the Purchaser’s expense;

(iv) Any Goods or parts of Goods replaced shall become the property of the

Company;

(v) No work whatsoever (other than normal and proper maintenance) has been

carried out to the Goods or any part of the Goods without the Company’s prior

written consent;

(vi) The defect has not arisen from a design made, furnished or speciﬁed by the

Purchaser;

(vii) The Goods have been assembled or incorporated into other goods only in

accordance with any instructions issued by the Company;

(viii) The defect has not arisen from a design modiﬁed by the Purchaser;

(ix) The defect has not arisen from an item manufactured by a person other than

the Company. In respect of any item manufactured by a person other than the

Company, the Purchaser shall only be entitled to the beneﬁt of any warranty or

guarantee provided by such manufacturer to the Company.

(b) In respect of computer software supplied by the Company the Company does not

warrant that the use of the software will be uninterrupted or error free.

(c) The Company accepts liability:

(i) For death or personal injury to the extent that it results from the negligence of

the Company, its employees (whilst in the course of their employment) or its

agents (in the course of the agency);

WA R R ANTY

ii

Redbox User Handbook No 3

(ii) For any breach by the Company of any statutory undertaking as to title, quiet

possession and freedom from encumbrance.

(d) Subject to conditions (a) and (c) from the time of despatch of the Goods from the

Company’s premises the Purchaser shall be responsible for any defect in the Goods

or loss, damage, nuisance or interference whatsoever consequential economic or

otherwise or wastage of material resulting from or caused by or to the Goods. In

particular the Company shall not be liable for any loss of proﬁts or other economic

losses. The Company accordingly excludes all liability for the same.

(e) At the request and expense of the Purchaser the Company will test the Goods to

ascertain performance levels and provide a report of the results of that test. The

report will be accurate at the time of the test, to the best of the belief and Knowledge

of the Company, and the Company accepts no liability in respect of its accuracy

beyond that set out in Condition (a).

(f) Subject to Condition (e) no representation, condition, warranty or other term, express

or implied (by statute or otherwise) is given by the Company that the Goods are of

any particular quality or standard or will enable the Purchaser to attain any particular

performance or result, or will be suitable for any particular purpose or use under

speciﬁc conditions or will provide any particular capacity, notwithstanding that the

requirement for such performance, result or capacity or that such particular purpose

or conditions may have been known (or ought to have been known) to the Company,

its employees or agents.

(g) (i) To the extent that the Company is held legally liable to the Purchaser for any

single breach of contract, tort, representation or other act or default, the

Company’s liability for the same shall not exceed the Price of the Goods.

(ii) The restriction of liability in Condition (g)(i) shall not apply to any liability

accepted by the Seller in Condition (c).

(h) Where the Goods are sold under a consumer transaction (as deﬁned by the

Consumer Transactions (Restrictions on Statements) Order 1976) the statutory

rights of the Purchaser are not aﬀected by these Conditions of Sale.

Unpacking the Redbox

The Redbox is shipped with the following equipment. Please check your packaging to

ensure that you have all of the items below. If anything is missing, please contact the

supplier of your equipment immediately.

Item Quantity

Redbox audio interface 1

IEC Mains lead ﬁtted with moulded mains plug 1

Handbook and warranty card 1

Fig A: Packing List.

WA R R ANTY

Redbox User Handbook No 3

iii

Each Redbox is shipped in protective packaging and should be inspected for damage before

use. Where an item is found to have transit damage, notify the carrier immediately with all

the relevant details of the shipment. Packing materials should be kept for inspection and

also for if the product needs to be returned.

Returning the Warranty Card

In order to register the date of purchase so that we can keep you informed of any design

improvements or modiﬁcations, it is important to complete the warranty registration

document that is enclosed and return it to Sonifex Ltd in the UK, or register online at

www.sonifex.co.uk/register

For your own records you should write down the serial number (which can be found on the

rear of the Redbox.

Serial Number ………………………………………

Safety Information

Safety of Mains Operated Equipment

This equipment has been designed to meet the safety regulations currently advised

in the country of purchase and it conforms to the safety regulations speciﬁed by

use of the CE Mark.

Warning : There are no user serviceable parts inside the equipment. If you should ever

need to look inside the unit, always disconnect the mains supply before removing the

equipment covers.

Voltage Setting Checks

Ensure that the machine operating voltage is correct for your mains power supply by

checking the box in which your Redbox was supplied. The voltage is shown on the box label.

The available voltage settings are 115V, or 230V. Please note that all Redboxes are either

switchable between 115V and 230V, or have a universal power supply.

Fuse Rating

The Redboxes are supplied with a single fuse in the live conducting path of the power

infeed at the power supply. For reasons of safety it is important that the correct rating

and type of fuse is used. Incorrectly rated fuses could present a possible ﬁre hazard, under

equipment fault conditions. The fuse ratings for the Redboxes are: -

Voltage Fuse

115 V 200mA, 5 x 20mm SB (except RB-SS10 which is 320 mA)

230 V 100mA, 5 x 20mm SB (except RB-SS10 which is 160 mA)

Fig B: Fuse Rating Table.

The active fuse is ﬁtted on the outside rear panel of the unit.

SAFETY & INSTALL ATION

INFORMATION

SAFETY & INSTALL ATION INFORMATION

iv

Redbox User Handbook No 3

Power Cable and Connection

An IEC power connector is supplied with the Redbox, which has a moulded plug, attached

– this is a legal requirement. If no moulded plug has been supplied with your Redbox, please

contact your supplier, because an IEC connector is always supplied from the Sonifex factory.

If for any reason, you need to use the Redbox with a diﬀerent power cable, you should use

the following wiring guidelines:

Wire Colour Connection

Green, or green and yellow Earth (E)

Blue, or Black Neutral (N)

Brown, or Red Live (L)

Fig C: Mains Cable Wire Colours

Ordering the Correct Mains Lead

When ordering a Redbox from Sonifex, it is helpful if you can specify your required

operating voltage and mains lead. After the product code add:

UK, for 230V, UK 3 pin to IEC lead

EC, for 230V, European Schuko 2 pin to IEC lead

US, for 115V, 3 pin to IEC lead

AU for 230V, Australasian 3 pin to IEC lead

Fig D: Mains Lead Table.

E.g. order RB-MA1 UK for a UK IEC lead to be supplied.

Installation Information

Atmosphere

The units should be installed in an area that is not subject to excessive temperature

variation (<0°C, >50°C), moisture, dust or vibration.

Electromagnetic Radiation

The cover is connected to earth by means of the ﬁxing screws. It is essential to maintain

this earth ground connection to ensure a safe operating environment and provide

electromagnetic shielding.

Fitting Redboxes

Redboxes can be ﬁxed to the underside of a mixing desk, or other surfaces using 4.2mm

holes in the sides and ﬁxed with 2 x M4 screws or 2 x No. 6 countersink wood screws.

SAFETY & INSTALL ATION INFORMATION

SAFETY & INSTALL ATION

INFORMATION

Redbox User Handbook No 3

v

They can also be rack-mounted, with either the front, or rear of the Redbox positioned at the

front of the rack:

Front Mounting Redboxes: For rack mounting smaller (28cm) units the optional RB-RK1

(Red) or RB-RK1B (Black) kit can be used (which include 4 oﬀ M6 panel ﬁxing screws).

Fig E: RB-RK1Small Redbox Front Rack-mount Kit .

Wherever you see this symbol an RB-RK1 front panel rack kit can be used :

Rear Mounting Redboxes: For rear panel mounting you can use either the RB-RK2, or

RB-RK3, depending on the size of your Redbox.

RB-RK2 1U rear panel rack kit for small Redbox range, e.g., RB-BL2

Fig F: RB-RK2 Small Redbox Rear Rack-mount Kit.

e.g. for ﬁtting an RB-BL2:

Wherever you see this symbol an RB-RK2 small Redbox rear panel 19” rack kit can be used :

RB-RK3 1U rear panel rack kit for large Redbox range, e.g., RB-DA6

Fig G: RB-RK3 Large Redbox Rear Rack-mount Kit.

e.g. for ﬁtting an RB-DA6:

Wherever you see this symbol an RB-RK3 large Redbox rear panel 19” rack kit can be used :

Note: When ﬁtting the rear-mounting rack-kits, a notch has been

left on the inside of the right-hand rack-piece for the mains cable to

pass through. Make sure that the mains cable has been put through

the notch before attaching the right hand rack-piece.

SAFETY & INSTALL ATION

INFORMATION

SAFETY & INSTALL ATION INFORMATION

vi

Redbox User Handbook No 3

WEEE & RoHS Directives - Sonifex Statement

The Waste Electrical and Electronic Equipment (WEEE) Directive was agreed on

13 February 2003, along with the related Directive 2002/95/EC on Restrictions

of the use of certain Hazardous Substances in electrical and electronic

equipment (RoHS).

The Waste Electrical and Electronic Equipment Directive (WEEE) aims to minimise the

impacts of electrical and electronic equipment on the environment during their life times

and when they become waste. It applies to a huge spectrum of products. It encourages

and sets criteria for the collection, treatment, recycling and recovery of waste electrical and

electronic equipment. All products manufactured by Sonifex Ltd have the WEEE directive

label placed on the case. It gives a contact for individuals who are unsure about the correct

procedure when the product has reached its “end of use”.

Sonifex Ltd will be happy to give you information about local organisations that can

reprocess the products, or alternatively all products that have reached “end of use” can be

returned to Sonifex and will be reprocessed correctly free of charge.

Sonifex Ltd has phased out the use of certain hazardous substances identiﬁed in the

European Union’s Restriction of Hazardous Substances (RoHS) directive. The RoHS directive

limits the use of certain hazardous substances currently used in EEE manufacture, including

lead, mercury, cadmium, hexavalent chromium, and halide-containing compounds PBB

(polybrominated biphenyl) and PBDE (polybrominated diphenyl ether). Elimination of these

substances will result in more environmentally friendly recycling of electronic equipment.

For the products which Sonifex manufacture, the main area where products were aﬀected

was in the use of lead for manufacturing and assembling electronics circuit boards.

Sonifex Ltd practices lead-free (LF) manufacturing processes. LF solder is used on the

surface-mount PCB manufacturing processes and for hand soldering. The printed circuit

boards (PCBs) used are either gold plated, or immersion tin plated, both of which use no

lead. Historically the PCBs were hot air solder levelled (HASL) PCBs which used tin/lead

based solder.

The manufacturing processes include the assembly of purchased components from various

sources. Product is oﬀered as RoHS compliant, or LF, only after suﬃcient evidence is received

from the component manufacturers that their components are RoHS compliant. Sonifex

Ltd relies solely on the distributor, or manufacturer, of the components for identiﬁcation of

RoHS compliance. Thus whilst every eﬀort is made to ensure compliance, Sonifex Ltd makes

no warranty, or certiﬁcation, or declaration of compliance concerning said components.

Sonifex Ltd deﬁnes “Lead Free” as pertaining to any product, which has been manufactured

by Sonifex Ltd using components which have been declared by the manufacturers as

“Lead Free”. All statements by Sonifex Ltd of RoHS compliance are based on component

manufacturer documentation.

SAFETY & INSTALL ATION INFORMATION

SAFETY & INSTALL ATION

INFORMATION

Redbox User Handbook No 3

1

MIXER & SOURCE SELECTORS - RB -SS10

MIXER & SOURCE SELECTORS

1

1 RB-SS10 10 Way Stereo Analogue Source Selector/Mixer

Introduction

Fig 1-1: RB-SS10 Front Panel.

The RB-SS10 10 Way Stereo Analogue Source Selector/Mixer is a 1U rack-mount unit that

produces a stereo analogue audio output from 10 selectable stereo analogue sources. There

are 10 illuminated front panel push buttons, which select and indicate the current channel

selection. The selection and indication is also available through a remote connector on the

rear panel. To stop accidental front panel selection there is a remote input to inhibit the

front panel buttons.

As well as being able to act as a source select module, the RB-SS10 can act as a mixer, by

enabling the mix mode (using the remote input).

The gain for left and right inputs can be individually adjusted by using the preset

potentiometers on the front panel.

As well as routing the selected audio signal, the unit will also route a remote signal input

through the remote connector to the selected input source, for starting external audio

equipment such as a CD player.

The front panel headphone output has its own volume control, which is independent of

the level adjustment for the main outputs, and has a maximum output level of +12dBu. The

volume control can be made to also alter the output level of the main XLR outputs by using

a switch on the rear panel to enable/disable this feature.

There is a designation strip on the front panel, useful for giving the buttons a meaningful

description. The strip covers the input gain controls so that once conﬁgured, they can’t

easily be altered – ideal for installation work.

The LED on the front panel is used to indicate that power is present on the unit.

2

Redbox User Handbook No 3

MIXER & SOURCE SELECTORS

MIXER & SOURCE SELECTORS - RB -SS10

1

System Block Diagram

Fig 1-2: RB-SS10 System Block Diagram.

Front Panel Indicators & Controls

Fig 1-3: RB-SS10 Front Panel.

Illuminated Push Buttons

The front panel contains 10 illuminated push buttons, used for selecting an analogue

source. The push button illuminates when the input is selected. The status of pin 12 on the

remote connector determines whether the unit is in the selector mode, or the mix mode.

When pin 12 is connected to 0V, mix mode is enabled.

In selector mode, one push of a button will select the desired analogue stereo source and

pushing the button again will turn it oﬀ.

Inputs

Remote

Start I/O

Remote

Start In

Front Panel

Inhibit

Mix Mode

Input Gain

Stage

Analogue

Switches

MCU

Status

Outputs

Headphone

Outputs

Vo

lume

Remote Select/

Switch Inputs

Push Button

Switches

Audio

Inputs

1

L

R

L

R

L

x10

R

L

R

2

Audio

Inputs

3-6

Audio

Inputs

7-10

Power LED

Indication

Headphone

Output

Volume

Control

Illuminated

Push Buttons

Front Panel

Gain Controls

Underneath

Designation Strip

Redbox User Handbook No 3

3

MIXER & SOURCE SELECTORS - RB -SS10

MIXER & SOURCE SELECTORS

1

In mix mode, each button you press will select that source allowing multiple sources to be

mixed to a single output. Pressing the button again will switch oﬀ a source.

There is also a remote input to inhibit the front panel switches. When the front panel inhibit

is active, pressing the front panel switches has no eﬀect on the current channel selection.

Front Panel Gain Controls

The input gain can be individually adjusted for left and right channels through pre-set

potentiometers which are accessible through the front panel. The gain range of the input is

-8dBu to +20dBu.

Headphone Output

The front panel headphone output is a ¼” stereo jack socket and is designed to drive

150mW into 32Ω - 600Ω professional headphones.

Volume Control

The volume control is used to alter the headphone output. It can also be used to alter the

main XLR output levels by using a rear panel switch to enable/disable the control.

Additional Modes

An option to set the unit in diﬀerent modes of operation is available and can be conﬁgured

at anytime while the unit is powered.

There are currently three modes of operation: Alternate mode, Latched mode and Protected

Alternate mode: -

Alternate Mode

In this mode the channels are selected and deselected by a press of the button, as described

previously.

Latched Mode

In this mode the selected channel is active only while the button is pressed. As soon as

button is released the channel becomes inactive.

Protected Alternate Mode

Operates in a similar manner to the Alternate mode, but a channel cannot be turned oﬀ

unless switching to another input or while operating in mix-mode and there is more than

one channel active. In other words, there will always be a channel routed to the output.

NOTE: after setting this mode there will be no channel selected.

Conﬁguring the Additional Modes

While the unit is powered, hold down the input 10 button and press the input 5 button

ﬁve times. Once completed, the input 10 button will start to ﬂash and the ﬁrst 3 input

buttons will display the current operating mode (as shown below). To change the mode,

simply press the input 10 and the buttons will indicate the newly selected mode. Once the

required operating mode has been set the unit will restart within ﬁve seconds from the last

button press.

4

Redbox User Handbook No 3

MIXER & SOURCE SELECTORS

MIXER & SOURCE SELECTORS - RB -SS10

1

INPUT 1 button on = Alternate mode

INPUT 2 button on = Latched mode

INPUT 3 button on = Protected Alternate mode

Rear Panel Connections and Operation

Fig 1-4: RB-SS10 Rear Panel.

Inputs

Two of the stereo analogue audio inputs are on XLR-3 pin sockets (female) so that they can

be used for equipment which you may want to plug/unplug on a regular basis and isn’t

pre-wired, e.g. portable recorders.

The four XLR-3 inputs can take balanced professional levels, or unbalanced by using the

front panel gain controls, and by connecting the non-phase to the signal ground. They have

the following connections:

Pin 1: Screen

Pin 2: Phase

Pin 3: Non-phase

Outputs

The two XLR 3 pin outputs are electronically balanced, and can be wired unbalanced. Each

output is individually buﬀered so that a short circuit on one output will not aﬀect the others.

They have the following connections:

Pin 1: Screen

Pin 2: Phase

Pin 3: Non-phase

Altering the Master Output Level

When the Output Level Control push-switch is Enabled (pushed in) on the rear panel, it

changes the functionality of the front panel volume control to also alter the level of the

master output, as well as the headphone volume.

Outputs

Input 1 Status

Outputs

Remote

Start I/O

Master

Output

Control

Additional

Audio Input

Connects

Remote Select/

Switch Inputs

Input 2

Redbox User Handbook No 3

5

MIXER & SOURCE SELECTORS - RB -SS10

MIXER & SOURCE SELECTORS

1

RB-SS10 Additional Audio Input Connectors

There are 2 oﬀ 25 way D-type sockets (female) used for the remaining audio inputs.

The INPUTS 3 - 6 (upper) connector contains analogue inputs 3-6, and the INPUTS 7 – 10

(lower) connector contains analogue inputs 7-10.

Pin No. I/O INPUTS 3 - 6 connector INPUTS 7 – 10 connector

Pin 1 I Audio input 3 left phase Audio input 7 left phase

Pin 2 - Chassis ground Chassis ground

Pin 3 I Audio input 3 right non-phase Audio input 7 right non-phase

Pin 4 I Audio input 4 left phase Audio input 8 left phase

Pin 5 - Chassis ground Chassis ground

Pin 6 I Audio input 4 right non-phase Audio input 8 right non-phase

Pin 7 I Audio input 5 left phase Audio input 9 left phase

Pin 8 - Chassis ground Chassis ground

Pin 9 I Audio input 5 right non-phase Audio input 9 right non-phase

Pin 10 I Audio input 6 left phase Audio input 10 left phase

Pin 11 - Chassis ground Chassis ground

Pin 12 I Audio input 6 right non-phase Audio input 10 right non-phase

Pin 13 - No internal connection No internal connection

Pin 14 I Audio input 3 left non-phase Audio input 7 left non-phase

Pin 15 I Audio input 3 right phase Audio input 7 right phase

Pin 16 - Chassis ground Chassis ground

Pin 17 I Audio input 4 left non-phase Audio input 8 left non-phase

Pin 18 I Audio input 4 right phase Audio input 8 right phase

Pin 19 - Chassis ground Chassis ground

Pin 20 I Audio input 5 left non-phase Audio input 9 left non-phase

Pin 21 I Audio input 5 right phase Audio input 9 right phase

Pin 22 - Chassis ground Chassis ground

Pin 23 I Audio input 6 left non-phase Audio input 10 left non-phase

Pin 24 I Audio input 6 right phase Audio input 10 right phase

Pin 25 - Chassis ground Chassis ground

Fig 1-5: Analogue Audio Inputs Pin Connections

6

Redbox User Handbook No 3

MIXER & SOURCE SELECTORS

MIXER & SOURCE SELECTORS - RB -SS10

1

RB-SS10 Remote Start I/O

This 25 way D-type plug (male) connector contains the remote start input connection and

the corresponding 10 opto-isolated remote start outputs. This is intended to be used as

a method for re-directing a remote start command using a single switch or mixer fader

start output, to selected equipment, i.e. CD player, or MD player, etc. This operates in both

selector mode and mix mode enabling a single switch to remotely control whichever source

is selected or mixed.

Pin No. I/O Description

Pin 1 O Start output 1 collector

Pin 2 O Start output 2 collector

Pin 3 O Start output 3 collector

Pin 4 O Start output 4 collector

Pin 5 O Start output 5 collector

Pin 6 O Start output 6 collector

Pin 7 O Start output 7 collector

Pin 8 O Start output 8 collector

Pin 9 O Start output 9 collector

Pin 10 O Start output 10 collector

Pin 11 - No internal connection

Pin 12 - No internal connection

Pin 13 I Remote start input signal

Pin 14 O Start output 1 emitter

Pin 15 O Start output 2 emitter

Pin 16 O Start output 3 emitter

Pin 17 O Start output 4 emitter

Pin 18 O Start output 5 emitter

Pin 19 O Start output 6 emitter

Pin 20 O Start output 7 emitter

Pin 21 O Start output 8 emitter

Pin 22 O Start output 9 emitter

Pin 23 O Start output 10 emitter

Pin 24 - No internal connection

Pin 25 - Signal ground

Fig 1-6: Remote Start Pin Connections.

Page is loading ...

Sonifex Redbox RB-MA1 Mic Preamp Owner's manual

Sonifex Redbox RB-MA1 Mic Preamp Owner's manual

Related papers

Other documents