CAB EOS1/EOS4 User manual

Category
Label printers
Type
User manual

This manual is also suitable for

Made in Germany
Dispenser Module
Operator's Manual
EOS4 P
2 2Operator's Manual
Edition: 03/2016 - Part No. 9009544
Copyright
This documentation as well as translation hereof are property of cab Produkttechnik
GmbH & Co. KG.
The replication, conversion, duplication or divulgement of the whole manual or parts
of it for other intentions than its original intended purpose demand the previous
written authorization by cab.
Editor
Regarding questions or comments please contact cab Produkttechnik GmbH & Co.
KG.
Topicality
Due to the constant further development of our products discrepancies between
documentation and product can occur.
Please check www.cab.de for the latest update.
Terms and conditions
Deliveries and performances are effected under the General conditions of sale of
cab.
Germany
cab Produkttechnik
GmbH & Co KG
Postfach 1904
D-76007 Karlsruhe
Wilhelm-Schickard-Str. 14
D-76131 Karlsruhe
Telefon +49 721 6626-0
Telefax +49 721 6626-249
www.cab.de
France
cab technologies s.a.r.l.
F-67350 Niedermodern
Téléphone +33 388 722 501
www.cab.de/fr
USA
cab Technology Inc.
Tyngsboro MA, 01879
Phone +1 978 649 0293
www.cab.de/us
South Africa
cab Technology (Pty.) Ltd.
2125 Randburg
Phone +27 11-886-3580
www.cab.de/za
Asia
cab Technology Co., Ltd.
Junghe, Taipei, Taiwan
Phone +886 2 8227 3966
www.cab.de/tw
China
cab (Shanghai)Trading Co., Ltd.
Phone +86 21 6236-3161
www.cab.de/cn
Representatives in other countries on request
3Table of Contents
1 Introduction .................................................................................... 4
1.1 Instructions ......................................................................................4
1.2 Intended Use ...................................................................................4
1.3 Safety Instructions ...........................................................................5
1.4 Environment .....................................................................................5
1.5 Technical Data .................................................................................6
1.6 Placement ........................................................................................ 6
2 Mounting .........................................................................................7
3 Media Loading ................................................................................8
4 Operation ........................................................................................ 9
4.1 Synchronizing the Paper Feed ........................................................9
4.2 Operation in Peel-off Mode ............................................................10
5 Maintenance ................................................................................. 11
6 Licences .......................................................................................12
6.1 Reference to the EU Declaration of Conformity .............................12
6.2 FCC ...............................................................................................12
4 41 Introduction
1.1 Instructions
Important information and instructions in this documentation are designated
as follows:
!
Attention!
Draws attention to possible dangers, material damage or loss of
quality.
i
Notice!
Gives you tips. They make a working sequence easier or draw
attention to important working processes.
Environment!
Gives you tips on protecting the environment.
Handling instruction
Reference to section, position, illustration number or document.
Option (accessories, peripheral equipment, special ttings).
Time
Information in the display.
1.2 Intended Use
The device is intended exclusively as an option for the EOS4 printers for
dispensing suitable materials that have been approved by the manufac-
turer. Any other use or use going beyond this shall be regarded as
improper use. The manufacturer/supplier shall not be liable for damage
resulting from unauthorized use; the user shall bear the risk alone.
Usage for the intended purpose also includes complying with the operating
manual, including the manufacturer‘s maintenance recommendations and
specications.
The device is manufactured in accordance with the current technological
status and the recognized safety rules. However, danger to the life and
limb of the user or third parties and/or damage to the device and other
tangible assets can arise during use.
The device may only be used for its intended purpose and if it is in perfect
working order, and it must be used with regard to safety and dangers as
stated in the operating manual.
i
Notice!
All documentations can also currently be found in the Internet.
51 Introduction
1.3 Safety Instructions
Disconnect the printer from the electrical outlet before mounting or
removing the dispenser module.
The dispenser module may only be operated when it is mounted on the
printer.
Work going beyond this may only be performed by trained personnel or
service technicians.
Unauthorized interference with electronic modules or their software can
cause malfunctions. Other unauthorized work on or modications to the
device can also endanger operational safety.
Always have service work done in a qualied workshop, where the
personnel have the technical knowledge and tools required to do the
necessary work.
Warning stickers must not be removed, as then you and other people
cannot be aware of dangers and may be injured.
!
Attention!
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
1.4 Environment
Obsolete devices contain valuable recyclable materials that should be sent
for recycling.
Send to suitable collection points, separately from residual waste.
The modular construction of the dispenser module enables it to be easily
disassembled into its component parts.
Send the parts for recycling.
Take the electronic circuit boards to public waste disposal centers or to
the distributor.
6 61 Introduction
1.5 Technical Data
for printer type EOS4
Liner width up to 120 mm
Label width single-lane 10 - 116
multi-lane 5 - 116
Label height 20 - 200
Power supply peripheral connector of the printer
!
Attention!
Limitations may apply to small labels, thin materials or strong
adhesives.
Critical materials or applications must be tested and approved.
1.6 Placement
1
2
i
Notice!
Place the printer in such a way that the dispenser module (1)
does not protrude the desktop (2) even with dispenser module
folded down.
7
!
Attention!
Disconnect the printer from the electrical outlet before
mounting or removing the dispenser module.
Mounting the peel-off plate
1
2
3
1. Fold down the cover with the tear-off plate (3).
2. Press the bars (1) out of the holders (2) an remove the cover.
8765
3. Insert the lug (6) of the peel-off plate (5) into the slot (7) of the printers
baseplate.
4. Press the peel-off plate against the printer and x it with screw (8).
2 Mounting
8 8
Mounting the Dispenser module
22 1 13
1. Press the bars (1) of the dispensing unit into the holders (2).
2. Fold up the dispensing unit and tighten the thumbscrews (3).
3 Media Loading
1
3
3
4
2
1. Load ribbon and media as described in printers manual.
Use the tear-off mode information for loading media.
2. Loosen the thumbscrews (3) and fold down the dispenser module.
3. Remove the labels from the protruding liner (4).
4. Guide the liner (4) immediately below the drawing roller (2) trough the
dispenser module.
5. Hold tight the liner (4), fold up the dispenser module and tighten the
thumbscrews (3).
2 Mounting
94 Operation
!
Attention!
Risk of media jam !
Ensure that the liner (2) can run off without hindrance.
4.1 Synchronizing the Paper Feed
After the label stock has been inserted, for peel-off mode a synchronization
of the paper feed is required. That way the rst label, which is detected by the
label sensor, will be transported to the print position and all labels in front (1)
will be fed out of the printer.
Press to start the synchronization.
Remove the blank labels (1) peeled-off during the synchronization.
i
Notice!
Synchronization is not necessary if the printhead was not opened
between different print jobs, even if the printer was switched off.
10 104 Operation
4.2 Operation in Peel-off Mode
1
3
4
1
2
4.2.1 Standard Operation
Under Setup -
>
Print param. -
>
Print on demand select the setting
Off. ( Conguration manual).
Active the peel-off mode in the software. With direct programming it is
controlled with the "P command" ( Programming manual).
Send a print job.
The rst label (3) will be printed, fed into the peel-off position and removed
from the liner (4) excepting the last ca 2 mm.
Remove the label. The removal will be registered by two see-through
sensors (1). If both sensors are free, the next label will be printed.
!
Attention!
When operating multi-lane media remove at last the labels which
are detected by the sensors (1).
4.2.2 Print on Demand
Under Setup -
>
Print param. -
>
Print on demand select the setting
On. ( Conguration manual).
Active the peel-off mode in the software. With direct programming it is
controlled with the "P command" ( Programming manual).
Send a print job.
The rst label (3) will be printed, fed into the peel-off position and removed
from the liner (4) excepting the last ca 2 mm.
Remove the label.
Select to start the next label.
11
Cleaning the Drawing Roller
Accumulations of dirt on the drawing roller may impair the peel-off quality.
!
Attention!
Damage of the drawing roller.
Do not use sharp objects (knives, screwdrivers, etc.) to clean
the drawing roller.
1
3
3
4
2
1. Loosen the thumbscrews (3) and fold down the dispenser module.
2. Remove the liner (4) from the dispenser module.
3. Remove deposits from the drawing roller (2) with roller cleaner.
4. Re-insert the liner (4), hold it tight, fold up the dispenser module and
tighten the thumbscrews (3).
5 Maintenance
12 126 Licences
6.1 Reference to the EU Declaration of Conformity
The Dispense Modules comply with the relevant fundamental regulations of
the EU Rules for Safety and Health:
Directive 2014/30/EU relating to electromagnetic compatibility
Directive 2011/65/EU on the restriction of the use of certain hazardous
substances in electrical and electronic equipment
EU Declaration of Conformity
https://www.cab.de/media/pushle.cfm?le=2723
6.2 FCC
NOTE : This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. The equipment generates, uses, and can radiate radio
frequency and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user may be required to correct
the interference at his own expense.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

CAB EOS1/EOS4 User manual

Category
Label printers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI