Matrix G7-S51 Owner's manual

Type
Owner's manual
3
PROPER USAGE
1. Do not exceed weight limits of the exercise device.
2. If applicable, set safety stops to appropriate height.
3. If applicable, adjust seat pads, leg pads, foot pads, range of motion
adjustment, or any other type of adjustment mechanisms to a comfortable
start position. Make certain that the adjusting mechanism is fully
engaged to prevent unintentional movement and to avoid injury.
4. Sit on bench (if applicable) and get into appropriate position for exercise.
5. Exercise using no more weight than you can safely lift and control.
6. In a controlled manner, perform exercise.
7. Return weight to its fully-supported start position.
WARRANTY
For North America, please visit  for warranty
information along with warranty exclusions and limitations.
PRODUCT SPECIFICATIONS
Max User Weight 136 kg / 300 lbs.
Max Training Weight 111.4 kg / 247.5 lbs.
Product Weight 290 kg / 640 lbs.
Overall Dimensions
(L x W x H)*
139 x 121 x 147 cm /
54.6 x 47.5 x 57.9”
* Ensure a minimum clearance width of 0.6 meters (24”) for access to and
passage around MATRIX strength equipment. Please note, 0.91 meters (36”)
is the ADA recommended clearance width for individuals in wheelchairs.
MAINTENANCE CHECKLIST
ACTION FREQUENCY
Clean Upholstery
1
Daily
Inspect Cables
2
Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips
1
As Needed
Lubricate Guide Rods
3
As Needed
1
Upholstery & Grips should be cleaned with a mild soap
and water or a non-ammonia based cleaner.
2
Cables should be inspected for cracks or frays and immediately replaced if present.
If excessive slack exists cable should be tightened without lifting the head plate.
3
Guide rods should be lubricated with Teon based lubricant. Apply the
lubricant to a cotton cloth and then apply up and down the guide rods.
ENGLISH
TORQUE VALUES
M10 Bolt (Nyloc Nut & Flowdrill) 77 Nm / 57 ft -lbs
M8 Bolts 25 Nm / 18 ft-lbs
M8 Plastic 15 Nm / 11 ft-lbs
M6 Bolts 15 Nm / 11 ft-lbs
Pad Bolts 10 Nm / 7 ft-lbs
4
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of MATRIX products to instruct all individuals, whether
they are the end user or supervising personnel on proper usage of the equipment.
It is recommended that all users of MATRIX exercise equipment be informed of the following information prior to its use.
Do not use any equipment in any way other than designed or intended by the manufacturer.
It is imperative that MATRIX equipment be used properly to avoid injury.
INSTALLATION
1. STABLE AND LEVEL SURFACE: MATRIX exercise equipment must be installed on a stable base and properly leveled.
2. 

3. Under no circumstances should you slide equipment across the oor due to risk of tipping. Use proper materials handling
techniques and equipment recommended by OSHA.
All anchor points must be able to withstand 750 lbs. (3.3 kN) pull-out force.
MAINTENANCE
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use
only replacement parts supplied by your country’s local MATRIX dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important
information. If unreadable or missing, contact your MATRIX dealer for a replacement.
3. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well
as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals.
4. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualied to do
so. MATRIX dealers will provide service and maintenance training at our corporate facility upon request.
ADDITIONAL NOTES
This equipment should only be used in supervised areas where access and control is specically
regulated by the owner. It is up to the owner to determine who is allowed access to this training
equipment. The owner should consider a user’s: degree of reliability, age, experience, etc.
This training equipment meets industry standards for stability when used for its intended
purpose in accordance with the instructions provided by the manufacturer.
This equipment is for indoor use only. This training equipment is a Class S product (designed for use in a commercial
environment such as a tness facility). This training equipment is in compliance with EN ISO 20957-1 and EN 957-2.
WARNING
DEATH OR SERIOUS INJURY CAN OCCUR ON THIS
EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID
INJURY!
1. Keep children under the age of 14 away from this
strength training equipment. Teenagers must be
supervised at all times while using this
equipment.
2. This equipment is not intended for use by persons
with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the equipment by a
person responsible for their safety.
3. All warnings and instructions should be read and
proper instruction obtained prior to use. Use this
equipment for its intended purpose ONLY.
4. Inspect the machine before use. DO NOT use
machine if it appears damaged or inoperable.
5. Do not exceed weight capacity of this equipment.
6. Check to see that the selector pin is completely
inserted into the weight stack.
7. NEVER use the machine with the weight stack
pinned in an elevated position.
8. NEVER use dumbbells or other means to
incrementally increase the weight resistance. Only
use the means provided directly from the
manufacturer.
9. Injuries to health may result from incorrect or
excessive training. Cease exercise if you feel faint
or dizzy. Obtain a medical exam before beginning
an exercise program.
10. Keep body, clothing, hair, and fitness accessories
free and clear of all moving parts.
11. Adjustable stops, where provided, must be used
at all times.
12. When adjusting any adjustable mechanism (stop
position, seat position, pad location, range of
motion limiter, pulley carriage, or any other type),
make certain that the adjustable mechanism is fully
engaged prior to use to prevent unintended motion.
13. Manufacturer recommends that this equipment be
secured to the floor to stabilize and eliminate
rocking or tipping over. Use a licensed contractor.
14. If equipment is NOT secured to floor: NEVER allow
resistance straps, ropes or other means to be
attached to this equipment, as this may result in
serious injury. NEVER use this equipment for
support during stretching, as this may result in
serious injury.
15. DO NOT REMOVE THIS LABEL. REPLACE IF
DAMAGED OR ILLEGIBLE.
ENGLISHENGLISH
5
ENGLISH
1
2
Adjust seat height
so upper arms lie
flat on arm pads
ABDOMINAL CRUNCH
ABDOMINAL CRUNCH
6

3MM L-Shaped Allen Wrench 10MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench Phillips Screwdriver
5MM L-Shaped Allen Wrench 8MM Open-End Wrench
6MM L-Shaped Allen Wrench 17MM Open-End Wrench
8MM L-Shaped Allen Wrench Guide Rod Lubrication
If any items are missing please contact your country’s local MATRIX dealer for assistance.
0 mm 10 20 30 40 50 60 70 80 90 100 110 120 130
UNPACKING
Thank you for purchasing a MATRIX Fitness product. It is inspected before it is
packaged. It is shipped in multiple pieces to facilitate the compact packaging of the
machine. Prior to assembly, conrm all the components by matching them with
the exploded diagrams. Carefully unpack the unit from this box and dispose of
the packing materials in accordance with your local laws. Exercise device must be
assembled by a trained assembly team or be pre-assembled prior to delivery.
CAUTION
To avoid injury to yourself and prevent damage to the frame components,
be sure to have proper assistance removing the frame pieces from this box.
Please be sure to install the equipment on a stable base, and properly level the
machine. Ensure a minimum clearance width of 0.6 meters (24”) for access to
and passage around MATRIX strength equipment. Please note, 0.91 meters (36”)
is the ADA recommended clearance width for individuals in wheelchairs.
ENGLISH
G7-S51 TRAINING AREA
1.39 M
(54.6”)
1.21 M
(47.5”)
FREE AREA
0.6 M (2 FT)
WIDE PATH
7
ENGLISH
2
E
D
B
F
G

 
B
D
E
F
G
Washer (Φ10.2)
Spring Washer (Φ10.2)
Hex Head Bolt (M10x25L)
Bolt (M10x20L)
Arc Washer (M10)
4
4
4
2
2
A
D
B
B
Z
1

 
A
B
C
D
Z
Bolt (M10x80L)
Washer (Φ10.2)
Nyloc Nut (M10)
Spring Washer (Φ10.2)
Plug
4
8
4
4
4
1
Pre-installed hardware
2
3
Be sure to remove the insulating sheet
when installing the rep counter.
Do not fully tighten frame connectors until
assembly is complete. Vibra-Tite 135 Red Gel
or equivalent must be used on all fasteners
that are not assembled with Nyloc Nuts.
8
F
J
K
L
M
N
B
C
D
A
C
G
H
I
H
3 4

 
A
B
C
D
G
H
I
Bolt (M10x80L)
Washer (Φ10.2)
Nyloc Nut (M10)
Spring Washer (Φ10.2)
Arc Washer (M10)
Bolt (M10x130L)
Bolt (M10x180L)
2
4
10
2
16
4
4

 
F
J
K
L
M
N
Bolt (M10x20L)
Stopper Plate
Axle
Screw (M6x12L)
Washer (Φ6.4)
Connect Rod
4
4
2
2
2
1
ENGLISH
9
ENGLISH
6

 
S
T
U
V
Bolt (M8x75L)
Washer (Φ8.4)
Sleeve
Nut (M8)
3
6
3
3
5

 
E
O
P
Q
R
Hex Head Bolt (M10x25L)
Bolt (M8x25L)
Cover
Vortex Spring
Axle
4
8
8
2
4
E
O
P
Q
R
S
T
U
V
T
10
ENGLISH
7

 
W Screw (M10x20L) 16
W
W
ASSEMBLY COMPLETE!
 
G7-S13  A9 B10 C13
G7-S23  A10 B11 C14
G7-S71  A8 B9 C13
G7-S72  A7 B11 C15
G7-S70  A10 B11 C14
G7-S33  A6 B7 C12
G7-S42  A5 B9 C12
G7-S34  A7 B8 C13
G7-S40  A12 B13 C15
G7-S74  A8 B9 C11
G7-S75  A6 B7 C11
G7-S22  A8 B9 C14
G7-S51  A10 B11 C13
G7-S52  A7 B8 C13
G7-S78  A9 B12 C15
G7-S55  A11 B12 C15
G7-S21  A8 B9 C15
G7-S73  A10 B11 C15
G7-S77  A9 B11 C15
* A = Top Sensor
B = Middle Sensor
C = Bottom Sensor

=
=
26
NEDERLANDS
7

 
W Schroef (M10X20L) 16
MONTAGE VOLTOOID!
W
W
 
G7-S13  A9 B10 C13
G7-S23  A10 B11 C14
G7-S71  A8 B9 C13
G7-S72  A7 B11 C15
G7-S70  A10 B11 C14
G7-S33  A6 B7 C12
G7-S42  A5 B9 C12
G7-S34  A7 B8 C13
G7-S40  A12 B13 C15
G7-S74  A8 B9 C11
G7-S75  A6 B7 C11
G7-S22  A8 B9 C14
G7-S51  A10 B11 C13
G7-S52  A7 B8 C13
G7-S78  A9 B12 C15
G7-S55  A11 B12 C15
G7-S21  A8 B9 C15
G7-S73  A10 B11 C15
G7-S77  A9 B11 C15
* A = Bovenste sensor
B = Middelste sensor
C = Onderste sensor

=
=
42
FRANÇAIS
7


 
W Vis (M10x20L) 16
LE MONTAGE EST TERMINÉ !
W
W



G7-S13  A9 B10 C13
G7-S23  A10 B11 C14
G7-S71  A8 B9 C13
G7-S72  A7 B11 C15
G7-S70  A10 B11 C14
G7-S33  A6 B7 C12
G7-S42  A5 B9 C12
G7-S34  A7 B8 C13
G7-S40  A12 B13 C15
G7-S74  A8 B9 C11
G7-S75  A6 B7 C11
G7-S22  A8 B9 C14
G7-S51  A10 B11 C13
G7-S52  A7 B8 C13
G7-S78  A9 B12 C15
G7-S55  A11 B12 C15
G7-S21  A8 B9 C15
G7-S73  A10 B11 C15
G7-S77  A9 B11 C15
* A = Capteur supérieur
B = Capteur intermédiaire
C = Capteur inférieur

=
=
61
ΕΛΛΗΝΙΚΑ
1
2
Adjust seat height
so upper arms lie
flat on arm pads
ABDOMINAL CRUNCH
ABDOMINAL CRUNCH
74
POLSKI
7

 
W Śruba (M10x20L) 16

W
W
 
G7-S13  A9 B10 C13
G7-S23  A10 B11 C14
G7-S71  A8 B9 C13
G7-S72  A7 B11 C15
G7-S70  A10 B11 C14
G7-S33  A6 B7 C12
G7-S42  A5 B9 C12
G7-S34  A7 B8 C13
G7-S40  A12 B13 C15
G7-S74  A8 B9 C11
G7-S75  A6 B7 C11
G7-S22  A8 B9 C14
G7-S51  A10 B11 C13
G7-S52  A7 B8 C13
G7-S78  A9 B12 C15
G7-S55  A11 B12 C15
G7-S21  A8 B9 C15
G7-S73  A10 B11 C15
G7-S77  A9 B11 C15
* A = Czujnik górny
B = Czujnik środkowy
C = Czujnik dolny

=
=
82
PORTUGUÊS
7

 
W Parafuso (M10 x 20L) 16
MONTAGEM CONCLUÍDA!
W
W



G7-S13  A9 B10 C13
G7-S23  A10 B11 C14
G7-S71  A8 B9 C13
G7-S72  A7 B11 C15
G7-S70  A10 B11 C14
G7-S33  A6 B7 C12
G7-S42  A5 B9 C12
G7-S34  A7 B8 C13
G7-S40  A12 B13 C15
G7-S74  A8 B9 C11
G7-S75  A6 B7 C11
G7-S22  A8 B9 C14
G7-S51  A10 B11 C13
G7-S52  A7 B8 C13
G7-S78  A9 B12 C15
G7-S55  A11 B12 C15
G7-S21  A8 B9 C15
G7-S73  A10 B11 C15
G7-S77  A9 B11 C15
* A = Sensor superior
B = Sensor central
C = Sensor inferior

=
=
85
РУССКИЙ
1
2
Adjust seat height
so upper arms lie
flat on arm pads
ABDOMINAL CRUNCH
ABDOMINAL CRUNCH
G7-S51-02
© 2018 Johnson Health Tech
Part # 1000415642
Rev 1.2 B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91

Matrix G7-S51 Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI