XDS-2170 Hardware User Manual
1
1. Introduction
This document describes the hardware of the XDS-2170
1.1. Package contents
1.2. Physical view and features
1.3. Installation
In some instances, due to major temperature deviation and change in elevation or environment, the
signboard's glass panel might trap slight moisture and will require at least 2-4 hours for the
condensation to evaporate prior to usage to avoid damaging the product.
Mounting with VESA compatible mounting interface
This smart signboard accepts a MIS-D100(100mm x 100mm) VESA-Compliant mounting interface, the
recommended screw is M4 x 9mm (excl. bracket thickness)
Installing the optional display stand
1 Place the display face down on a still surface, use clean cloth as cushion underneath is suggested
2 Place the stand on the mounting bracket and install the screw
Main Unit
Power Cord
(with select power plug)
2
3 Adjust the stand to switch between portrait/landscape installation
Alternatively, user can rotate the screen to change its orientation follow the instruction as shown below:
1.4. Setting up
Using control buttons
1 To unlock the control button, press and hold up and down buttons for 10 seconds, OSD unlocked notification
will pop up on screen
2 Button function table
Switch input source
1 Press AUTO button to access input source menu as shown below
2 Press AUTO button to switch between D-SUB,HDMI and Digital Signage, then press MENU button to enter the
selected source
3
The OSD menu
1 Press MENU button to access OSD MENU, please check appendix for full menu explanation
Factory reset by OSD
There are 2 methods to perform factory reset, below describes the step to reset by OSD
1 Unlock control button if it is locked
2 Press AUTO button to access input source menu first
3 Press and hold up button for 5 seconds to access reset menu as shown below
4 Press up/down button to change focus to Reset and press MENU button to enter Reset option
5 Press up/down button to change setting as Yes then press MENU button to perform factory reset
Factory reset by long press control button
Alternatively, user can perform factory reset by long press control button
1 Power off device by remove power cord
2 Press and hold up button and then power on by connect power cord to the unit
3 Keep holding up button until power led blinks
4
2. Technical Data
2.1. Specifications
XDS-2170
Display
21.5” IPS LCD panel
250 nits maximum brightness
1920x1080 panel resolution
Viewing angle (H/V): 178/178
Video format support
H.264 (up to 1080p,10Mbps)
VC-1 (up to 1080p,10Mbps)
MPEG-4 ASP (up to 1080p,10Mbps)
MPEG-2 (up to 1080p,10Mbps)
POPAI Screen Media Standards : S6 to S12, E4,E7,E8
Image format support
JPEG,PNG up to 1920x1080
POPAI Screen Media Standards : S1 to S3, E1 to E3
Audio codec support
MP3 up to 320Kbps
POPAI Screen Media Standards : S4, S5
Dynamic content
W3C HTML5 (HTML, CSS, JavaScript)
W3C SMIL 3.0 instructions (sub-set)
Interactivity
GPIO via PIO-101 module (optional)
Physical I/O connectors
Micro SD card slot
Micro USB for ADB(Android Debug Bridge)
3.5mm audio out
USB ports x 2
Ethernet port x 1
3.5mm audio in
VGA in
HDMI in
Power jack
Kensington lock
Embedded wireless antenna
Built-in stereo speaker 2w x 2
Local storage
8GB on-board eMMC with micro SD card expansion slot
Accessories
Power cord
Power requirement
AC 100-240V, 50~60Hz
Power consumption
Approximately 37 watts (average)
Environmental
Operating temperature: 0 – 45° C / 32 – 113° F
Humidity: 10 – 85% @ 45° C / 113° F non-condensing
Dimensions
522.4 x 318.4 x 57.2mm (20.5 x 12.5 x 2.25 inches)
Weight
3.65 Kg
8.05 lbs
Certifications
CE/FCC
Warranty
One-year limited parts & labor
5
3. Appendix
3.1. OSD Menu
Main Menu
Item
1
st
Sub Menu
Item
2
nd
Sub
Menu
Item
Description
Adjust
Range
Reset Value
Luminance
Contrast
N/A
Contrast
0-100
50
Brightness
N/A
Backlight Adjustment
0-100
90
Eco Mode
N/A
Brightness = 90,
Contrast = 50
Adjustable
Standard
Standard
Mode
Brightness = 20,
Contrast = 50
Not Adjustable
Text
Brightness = 40,
Contrast = 50
Not Adjustable
Internet
Brightness = 60,
Contrast = 50
Not Adjustable
Game
Brightness = 80,
Contrast = 50
Not Adjustable
Movie
Brightness = 100,
Contrast = 50
Not Adjustable
Sports
DCR
N/A
Dynamic contrast ratio
On/Off
Off
Image
Setup
Clock
N/A
Adjust picture Clock to reduce Vertical-
Line noise
0-100
Do Auto
Config
Phase
N/A
Adjust Picture Phase to reduce
Horizontal-Line noise
0-100
Do Auto
Config
H. Position
N/A
Adjust the horizontal position of the
picture
0-100
50
V. Position
N/A
Adjust the vertical position of the
picture
0-100
50
Image Ratio
N/A
Not Adjustable
Wide
Default to
panel native
aspect ratio
Color
Temp.
Warm
N/A
Set Color Temperature to Warm
N/A
Normal
N/A
Set Color Temperature to Normal
N/A
Cool
N/A
Set Color Temperature to Cool
N/A
6
User
Red
Red Gain
0-100
The User
R/G/B value
(default is
50) will not
be modified
by Reset
function
Green
Green Gain
0-100
Blue
Blue Gain
0-100
sRGB
N/A
Set Color Temperature to sRGB
N/A
OSD Setup
H. Position
N/A
Adjust the horizontal position of the OSD
0-100
50
V. Position
N/A
Adjust the vertical position of the OSD
0-100
50
Timeout
N/A
Adjust the OSD timeout
5-100
10
Language
N/A
Set OSD display language
English
English
Español
Français
Português
Русский
简体中文
繁體中文
한국어
OSD Lock
N/A
Turn On/Off OSD Lock
On
Extra
Input Select
N/A
Select input source
D-SUB
N/A
HDMI
Digital
Signage
DDC/CI
N/A
Select DDC/CI on or off
On
On
Off
Reset
N/A
Clear each old status of Auto-
configuration and set the color
temperature to Warm
Yes
Yes
Do not execute reset, return to main
menu.
No
Information
N/A
N/A
N/A
Resolution:
(H)x(V)
H. Frequency:
(KHz)
V. Frequency:
(Hz)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
