Sunjoy 110102032 User manual

Brand: Sunjoy

Model: 110102032

Type: User manual

This manual is also suitable for

110102036

ASSEMBLY INSTRUCTIONS

D-GZ845PCO-H (Black Top) / D-GZ845PCO-H1 (Faux Copper Top)

Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start

to finish. The final product will be a quality piece that will go together smoothly and give years

of enjoyment. All you will need is a screwdriver, a hammer and

two

ladders (not included)

whose height is no less than 2.5m.

Note: THIS UNIT IS HEAVY!

Do NOT assemble this item alone for safety. Six people are necessary.

Item Identification: For ease of identification, all parts are labeled to correspond to the Step

number in which the part is used.

Parts List

Part# Qty. Name Picture Part# Qty. Name Picture

A1 8 Gutter

B1 8

Corner

connector

C1 8

Large top roof

bar

D1 1

Roof

connection

H1 1 Center hook

I1 8 Top roof bar

J1 1 Top connector

B2 8 Roof panel

C2 8

Top roof

covering

D2 1 Top roof

F2 8

Large roof panel

G2 8

Large roof

panel 2

H2 16 Baffle 1

A2 16 Baffle 2

I2 8

Upper covering

for large roof

A3 4 Post 1

B3 4 Post 2

C3-1 2 Side panel 1

C3-2 2 Side panel 2

D3 8 Baffle

E3 2 Planter box

F3 4

Side panel of

planter box

G3 2 Slate table top

H3 2 Plate

I3 4 Top bracket

T1 8

Short netting

bar

T2 8 Long netting bar

S1 16

Left

connector

S2 16 Right connector

SETP 1

（X16）AA

M6X35mm

TBZ01406035HQ

（X130）BB

M6 加大垫片

TBZ10806HQ

（X58）CC

M6X15mm

TBZ00306015HQ

（X24）II

M6X15mm

TBZ01406015HQ

（X32）DD

M6X55mm

TBZ00306055HQ

（X32）EE

TBZ20106HQ

（X2）W1

M6 Wrench

Hardware Pack for STEP 1

Qty. Part # Name Picture

16 a M6*35 Bolt

152 b M6” Flat washer

64 g M6*20 Bolt

40 i M6*15 Bolt

16 d M6*55 Bolt

16 h M6*55 Bolt

16 e M6 Nut

2 w1 M6 Wrench

16 j Ф8*260 Stake

16 o

Ф10*70 Expansion

bolt

Fig.1: Attach Gutter (A1) to Post A3 & B3 with Bolt (g) and Washer (b).

Fig.2: Attach Side panel C3-1(C3-2) to Post A3 & B3 with Bolt (h) and Washer (b). (Make sure the side with hole

is outside)

Fig.3: Two person set up the assembled post and another person raises Gutter (A1), the fourth person

attaches (A1) to the assembled post with Bolt (g & a) and Flat washer (b). Assemble all gutters and tighten.

Fig.4: Use Stake (j) to fasten the post to the ground if it is soft surface.

Fig.5: Use Expansion bolt (o) to fasten the post to the ground if it is hard surface.

Hardware Pack for STEP 2

Qty. Part # Name Picture

152 b M6 Flat washer

16 f M6*45 Bolt

56 c M6*15 Bolt

64 i M6*15 Bolt

8 h M6*55 Bolt

8 e M6 Nut

1 m M10 Wrench

1 k M10 Nut

1 l M10 Flat washer

Fig.6: Attach Corner connector (B1) to Gutter (A1) with Bolt (i) and Washer (b).

Fig.7: Attach Baffle (D3) to Gutter (A1) with Bolt (g) and Washer (b).

Fig.8-1: Attach Corner connector (B1) to Large top roof bar (C1) with Bolt (d), Flat washer (b) and Nut (e).

Fig.8-2: Attach Large top roof bar (C1) to Roof connection (D1) with Bolt (i) and Flat washer (b).

Fig.9-1: Attach Center hook (H1) to Top connector (J1).

Fig.9-2: Attach Top roof bar (I1) to Top connector (J1) with Bolt (h), flat Washer (b) and Nut (e).

Fig.10: Attach Top roof bar (I1) to Roof connection (D1) with Bolt (c), flat Washer (b).

Fig.11: Attach Roof panel (B2) to Top roof bar (I1) with Bolt (c) and Flat washer (b).

Fig 12: Attach Top roof covering (C2) to Top roof bar (I1) with Bolt (f) and Flat washer (b).

Fig 13: Attach Top roof (D2) to Top connector (J1) with Nut (k) and Flat washer (l).

Fig.15-1: Insert Upper covering for large roof (I2) into the hole of Top roof bar (I1).

Fig.15-2: Attach Upper covering for large roof (I2) to Baffle 2 (A2) with Bolt (c) and Flat washer (b).

Fig.14-1: Attach Baffle 1 (H2) to Large roof panel 1(F2) with Bolt (i) and Flat washer (b). Back surface is labeled UP.

Fig.14-2: Slide Large roof panel 2 (G2) under Large roof panel 1 (F2).

Fig.14.3: Attach Baffle 2 (A2) to Large roof panel 2 (G2) with Bolt (i) and Flat washer (b).

Fig.14.4: Attach Large roof panel 2 (G2) to the corner of Gutter (A1) with Bolt (c) and Flat washer (b).

Hardware Pack for STEP 3

Qty. Part # Name Picture

44 b M6 Flat washer

20 i M6*15 Bolt

24 n M6*25 Bolt

Fig.16-1: Attach Side panel (F3) to Planter box (E3) with Bolt (n) and Flat washer (b).

Fig.16-2: Hang the assembled planter box on the Side panel 2 (C3-2).

Fig.17-1: Attach Top bracket (I3) to Side panel 1 (C3-1) with Bolt (i) and Flat washer (b); attach Slate table top

(G3) to Top bracket (I3) at the same time.

Fig.17-2: Attach Plate (H3) to Slate table top (G3) and Side panel 1 (C3-1) with Bolt (i) and Flat washer (b).

Fig.18-1: Insert Short netting bar (T1) and Long netting bar (T2) into Connector (S1/S2).

Spare Parts

Qty. Part # Name Picture

2 a M6*35 Bolt

8 b M6 Flat washer

4 c M6*15 Bolt

2 d M6*55 Bolt

2 e M6 Nut

2 f M6*45 Bolt

2 g M6*20 Bolt

2 h M6*55 Bolt

2 i M6*15 Bolt

1 k M10 Nut

1 l M10 Flat washer

2 n M6*25 Bolt

Fig.18-2: Attach Connector（S1/S2）to Baffle (D3).

1. Keep all children and pets away from assembly area. Children and pets should be

supervised when they are in the area of gazebo construction.

IMPORTANT:

2. The area for assembly should not be less than 6 feet from any obstruction such as fence,

garage, house, overhanging branches, laundry line or electrical wires.

3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe

assembly.

4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.

5. When assembling and using this product, basic safety precautions should always be

followed to reduce the risk of personal injury and damage to equipment. Please read all

instructions before assembly and use.

6. For outdoor use only. Install on level ground. Stakes are provided to secure the gazebo in

grass ground. If you wish to secure the gazebo to a wood deck or concrete surface, you will

need to purchase fasteners appropriate for these surfaces. These are readily available at your

local hardware store or home center.

7. Check all bolts for tightness before and during usage.

8. Please check your state and local regulations prior to purchasing. Some jurisdictions may

require permits for, or otherwise regulate, installation and use.

9. While this gazebo is manufactured to withstand gale force winds utilizing only the supplied

ground stakes, in areas subject to frequent severe weather, securing the gazebo to a deck,

concrete patio or footings should be considered.

10. Your gazebo has been engineered to accommodate winter snow loads incurred in most

areas. Removal of accumulated snow on the gazebo roof with a roof rake is recommended.

In areas that are regularly subject to blizzard conditions however, removal of the roof panel is

suggested. The assembled roof structure can simply be left intact until warmer conditions

return.

Limited Warranty:

This limited warranty is extended to the original purchaser and applies to defects in materials

and workmanship of your item provided the item is maintained with care and used only for

personal, residential purposes.

The item is warranted to be free from defects in material or workmanship for a period of one (1)

year. We don't reimburse for transportation or delivery costs, or compensate the individual or

any outside party for assembling or disassembling the product.

Exclusions:

Items used for commercial, contract, or other non-residential purposes, or items damaged due

to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or

rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for

warranty claims. Warranty is to the original purchaser and is non-transferable. Any

replacement of warranted items will be in the original style and color, or a similar style and

color if the original is unavailable or has been discontinued. As some states do not allow

exclusions or limitations on an implied warranty, the above exclusions and limitations may not

apply. This warranty gives you specific rights, and you may also have other rights, which vary

from state to state.

Maintenance:

Our iron/steel components for garden accessories and patio items are coated with rust

inhibiting paint that protects it from rusting.

However, due to the nature of iron, surface

oxidation (rusting) will occur once these protective coatings are scratched.

This is a natural

process and is not a defect! To minimize this condition, we recommend care when assembling

& handling the product to prevent scratching the paint. Should any scratching or damage occur,

we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily

removed with a very light application of common cooking oil. If surface oxidation (rusting)

occurs and if no measure is taken to prevent this, the oxidation may start dripping on to deck or

patio and cause damaging stains, which may be difficult to remove. This can be prevented if

measure is taken to keep the product from oxidizing.

Important: Please do not return this product to the store. For technical assistance on

assembly or replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am

EST to 8:00 pm PST or fax the replacement part form which is in the box to 1-740-283-3549 or

Email customer.care@sunjoygroup.com for assistance.

Made in China

GAZEBO NETTING AND CURTAIN ASSEMBLY INSTRUCTIONS

Netting / Curatin is available separately

Fig.19-2: Pull out Short netting

bar (T1) and Long netting bar

(T2) from Connector (S1/S2).

Fig.20: Hang the five rings of curtain into

Short netting bar (T1) from right side,

then insert Short netting bar (T1) into Right

connector (S2).

Fig.19-1: Raise Connector

(S2/S1) and take them down.

Fig.21: Hang the other rings

of curtain into adjacent Short

netting bar (T1) from left side,

insert Short netting bar (T1)

into Left connector (S1).

ig.22: Attach assembled

Connector (S2/S1) to two sides

of Baffle (D3) respectively.

Fig.23: Hang the five rings of Mosquito

netting into Long netting bar (T2) from

right side, then insert Long netting bar

(T2) into Right connector (S2).

Fig.24: Hang the other rings of

Mosquito netting into adjacent

Long netting bar (T2) from left

side, insert Long netting bar (T2)

into Left connector (S1).

Fig.25

: Attach assembled

Connector (S2/S1) to two sides

of Baffle (D3) respectively.

Sunjoy 110102032 User manual

Brand: Sunjoy

Model: 110102032

Type: User manual

This manual is also suitable for

110102036

Download PDF

report

Sunjoy 110102032 User manual

This manual is also suitable for

Sunjoy 110102032 User manual

Related papers

Other documents