Sunjoy 110102032 User manual

Type
User manual

This manual is also suitable for

1
ASSEMBLY INSTRUCTIONS
D-GZ845PCO-H (Black Top) / D-GZ845PCO-H1 (Faux Copper Top)
Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start
to finish. The final product will be a quality piece that will go together smoothly and give years
of enjoyment. All you will need is a screwdriver, a hammer and
two
ladders (not included)
whose height is no less than 2.5m.
Note: THIS UNIT IS HEAVY!
Do NOT assemble this item alone for safety. Six people are necessary.
Item Identification: For ease of identification, all parts are labeled to correspond to the Step
number in which the part is used.
2
Parts List
Part# Qty. Name Picture Part# Qty. Name Picture
A1 8 Gutter
B1 8
Corner
connector
C1 8
Large top roof
bar
D1 1
Roof
connection
H1 1 Center hook
I1 8 Top roof bar
J1 1 Top connector
B2 8 Roof panel
C2 8
Top roof
covering
D2 1 Top roof
F2 8
Large roof panel
1
G2 8
Large roof
panel 2
H2 16 Baffle 1
A2 16 Baffle 2
I2 8
Upper covering
for large roof
A3 4 Post 1
B3 4 Post 2
C3-1 2 Side panel 1
C3-2 2 Side panel 2
D3 8 Baffle
E3 2 Planter box
F3 4
Side panel of
planter box
G3 2 Slate table top
H3 2 Plate
I3 4 Top bracket
T1 8
Short netting
bar
T2 8 Long netting bar
S1 16
Left
connector
S2 16 Right connector
3
SETP 1
X16AA
M6X35mm
TBZ01406035HQ
X130BB
M6 加大垫片
TBZ10806HQ
X58CC
M6X15mm
TBZ00306015HQ
X24II
M6X15mm
TBZ01406015HQ
X32DD
M6X55mm
TBZ00306055HQ
X32EE
M6
TBZ20106HQ
X2W1
M6 Wrench
Hardware Pack for STEP 1
Qty. Part # Name Picture
16 a M6*35 Bolt
152 b M6Flat washer
64 g M6*20 Bolt
40 i M6*15 Bolt
16 d M6*55 Bolt
16 h M6*55 Bolt
16 e M6 Nut
2 w1 M6 Wrench
16 j Ф8*260 Stake
16 o
Ф10*70 Expansion
bolt
4
Fig.1: Attach Gutter (A1) to Post A3 & B3 with Bolt (g) and Washer (b).
Fig.2: Attach Side panel C3-1(C3-2) to Post A3 & B3 with Bolt (h) and Washer (b). (Make sure the side with hole
is outside)
Fig.3: Two person set up the assembled post and another person raises Gutter (A1), the fourth person
attaches (A1) to the assembled post with Bolt (g & a) and Flat washer (b). Assemble all gutters and tighten.
Fig.4: Use Stake (j) to fasten the post to the ground if it is soft surface.
Fig.5: Use Expansion bolt (o) to fasten the post to the ground if it is hard surface.
5
Hardware Pack for STEP 2
Qty. Part # Name Picture
152 b M6 Flat washer
16 f M6*45 Bolt
56 c M6*15 Bolt
64 i M6*15 Bolt
8 h M6*55 Bolt
8 e M6 Nut
1 m M10 Wrench
1 k M10 Nut
1 l M10 Flat washer
Fig.6: Attach Corner connector (B1) to Gutter (A1) with Bolt (i) and Washer (b).
Fig.7: Attach Baffle (D3) to Gutter (A1) with Bolt (g) and Washer (b).
Fig.8-1: Attach Corner connector (B1) to Large top roof bar (C1) with Bolt (d), Flat washer (b) and Nut (e).
Fig.8-2: Attach Large top roof bar (C1) to Roof connection (D1) with Bolt (i) and Flat washer (b).
6
Fig.9-1: Attach Center hook (H1) to Top connector (J1).
Fig.9-2: Attach Top roof bar (I1) to Top connector (J1) with Bolt (h), flat Washer (b) and Nut (e).
Fig.10: Attach Top roof bar (I1) to Roof connection (D1) with Bolt (c), flat Washer (b).
Fig.11: Attach Roof panel (B2) to Top roof bar (I1) with Bolt (c) and Flat washer (b).
Fig 12: Attach Top roof covering (C2) to Top roof bar (I1) with Bolt (f) and Flat washer (b).
Fig 13: Attach Top roof (D2) to Top connector (J1) with Nut (k) and Flat washer (l).
7
Fig.15-1: Insert Upper covering for large roof (I2) into the hole of Top roof bar (I1).
Fig.15-2: Attach Upper covering for large roof (I2) to Baffle 2 (A2) with Bolt (c) and Flat washer (b).
Fig.14-1: Attach Baffle 1 (H2) to Large roof panel 1(F2) with Bolt (i) and Flat washer (b). Back surface is labeled UP.
Fig.14-2: Slide Large roof panel 2 (G2) under Large roof panel 1 (F2).
Fig.14.3: Attach Baffle 2 (A2) to Large roof panel 2 (G2) with Bolt (i) and Flat washer (b).
Fig.14.4: Attach Large roof panel 2 (G2) to the corner of Gutter (A1) with Bolt (c) and Flat washer (b).
8
Hardware Pack for STEP 3
Qty. Part # Name Picture
44 b M6 Flat washer
20 i M6*15 Bolt
24 n M6*25 Bolt
Fig.16-1: Attach Side panel (F3) to Planter box (E3) with Bolt (n) and Flat washer (b).
Fig.16-2: Hang the assembled planter box on the Side panel 2 (C3-2).
9
Fig.17-1: Attach Top bracket (I3) to Side panel 1 (C3-1) with Bolt (i) and Flat washer (b); attach Slate table top
(G3) to Top bracket (I3) at the same time.
Fig.17-2: Attach Plate (H3) to Slate table top (G3) and Side panel 1 (C3-1) with Bolt (i) and Flat washer (b).
Fig.18-1: Insert Short netting bar (T1) and Long netting bar (T2) into Connector (S1/S2).
Spare Parts
Qty. Part # Name Picture
2 a M6*35 Bolt
8 b M6 Flat washer
4 c M6*15 Bolt
2 d M6*55 Bolt
2 e M6 Nut
2 f M6*45 Bolt
2 g M6*20 Bolt
2 h M6*55 Bolt
2 i M6*15 Bolt
1 k M10 Nut
1 l M10 Flat washer
2 n M6*25 Bolt
Fig.18-2: Attach ConnectorS1/S2to Baffle (D3).
10
1. Keep all children and pets away from assembly area. Children and pets should be
supervised when they are in the area of gazebo construction.
IMPORTANT:
2. The area for assembly should not be less than 6 feet from any obstruction such as fence,
garage, house, overhanging branches, laundry line or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe
assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use.
6. For outdoor use only. Install on level ground. Stakes are provided to secure the gazebo in
grass ground. If you wish to secure the gazebo to a wood deck or concrete surface, you will
need to purchase fasteners appropriate for these surfaces. These are readily available at your
local hardware store or home center.
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions may
require permits for, or otherwise regulate, installation and use.
9. While this gazebo is manufactured to withstand gale force winds utilizing only the supplied
ground stakes, in areas subject to frequent severe weather, securing the gazebo to a deck,
concrete patio or footings should be considered.
10. Your gazebo has been engineered to accommodate winter snow loads incurred in most
areas. Removal of accumulated snow on the gazebo roof with a roof rake is recommended.
In areas that are regularly subject to blizzard conditions however, removal of the roof panel is
suggested. The assembled roof structure can simply be left intact until warmer conditions
return.
Limited Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials
and workmanship of your item provided the item is maintained with care and used only for
personal, residential purposes.
The item is warranted to be free from defects in material or workmanship for a period of one (1)
year. We don't reimburse for transportation or delivery costs, or compensate the individual or
any outside party for assembling or disassembling the product.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due
to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or
rusting of hardware is not covered. Proof of purchase (dated register receipt) is required for
warranty claims. Warranty is to the original purchaser and is non-transferable. Any
replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow
exclusions or limitations on an implied warranty, the above exclusions and limitations may not
apply. This warranty gives you specific rights, and you may also have other rights, which vary
from state to state.
11
Maintenance:
Our iron/steel components for garden accessories and patio items are coated with rust
inhibiting paint that protects it from rusting.
However, due to the nature of iron, surface
oxidation (rusting) will occur once these protective coatings are scratched.
This is a natural
process and is not a defect! To minimize this condition, we recommend care when assembling
& handling the product to prevent scratching the paint. Should any scratching or damage occur,
we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily
removed with a very light application of common cooking oil. If surface oxidation (rusting)
occurs and if no measure is taken to prevent this, the oxidation may start dripping on to deck or
patio and cause damaging stains, which may be difficult to remove. This can be prevented if
measure is taken to keep the product from oxidizing.
Important: Please do not return this product to the store. For technical assistance on
assembly or replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00 am
EST to 8:00 pm PST or fax the replacement part form which is in the box to 1-740-283-3549 or
Email customer.care@sunjoygroup.com for assistance.
Made in China
12
GAZEBO NETTING AND CURTAIN ASSEMBLY INSTRUCTIONS
Netting / Curatin is available separately
13
Fig.19-2: Pull out Short netting
bar (T1) and Long netting bar
(T2) from Connector (S1/S2).
Fig.20: Hang the five rings of curtain into
Short netting bar (T1) from right side,
then insert Short netting bar (T1) into Right
connector (S2).
Fig.19-1: Raise Connector
(S2/S1) and take them down.
Fig.21: Hang the other rings
of curtain into adjacent Short
netting bar (T1) from left side,
insert Short netting bar (T1)
into Left connector (S1).
F
ig.22: Attach assembled
Connector (S2/S1) to two sides
of Baffle (D3) respectively.
Fig.23: Hang the five rings of Mosquito
netting into Long netting bar (T2) from
right side, then insert Long netting bar
(T2) into Right connector (S2).
Fig.24: Hang the other rings of
Mosquito netting into adjacent
Long netting bar (T2) from left
side, insert Long netting bar (T2)
into Left connector (S1).
Fig.25
: Attach assembled
Connector (S2/S1) to two sides
of Baffle (D3) respectively.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Sunjoy 110102032 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI