Haima 7 User manual

Content

Power supply system .......................................... T-1

Precautions to fuse use ....................................... T-1

Removal/installation of main fuse ...................... T-1

Removal/installation indoor fuse box................. T-1

Removal/installation of ignition switch ............. T-1

Check of ignition switch .................................... T-1

Removal/installation of key-in reminder switch T-2

Check of key-in reminder switch ....................... T-2

Removal/installation of cigar-lighter .................. T-2

Essentials to removal of socket .......................... T-3

Essentials to removal of ring .............................. T-3

Check of cigar-lighter ......................................... T-3

Lighting and signal system ................................. T-4

Headlamp ........................................................... T-4

Removal/installation of headlamp ...................... T-4

Light regulation of headlamp ............................. T-4

Removal/installation of headlamp bulb .............. T-4

Removal/installation of front fog lamps ............. T-5

Removal/installation of front fog lamp bulb ...... T-5

Removal/installation of rear combined lamps .... T-5

Removal/installation of rear combined lamp bulbT-6

Removal/installation of high-positioned brake light

............................................................................ T-6

Removal/installation of license plate lamp ........ T-6

Removal/installation of license plate lamp bulb T-7

Removal/installation of reading light ................. T-7

Removal/installation of reading light bulb ......... T-7

Removal/installation of indoor light and bulb .... T-8

Removal/installation of trunk lamp and bulb ..... T-8

Removal/installation of the lighting bulb of ignition

switch ................................................................. T-8

Removal/installation of dome lamp bulb ........... T-9

Wiper and washer ............................................... T-8

Removal/installation of windshield wiper motorT-8

Disassembly/assembly of windshield wiper motor

............................................................................ T-8

Check of windshield wiper motor ...................... T-8

Removal/installation of windshield wiper arm and

wiper blade ......................................................... T-9

Essentials to installation of windshield wiper armT-9

Removal/installation of the fluid reservoir of washer

............................................................................ T-9

Removal/installation of windshield washer motorT-9

Check of windshield washer motor .................. T-10

Removal of windshield washer nozzle ............. T-10

Installation of windshield washer nozzle ......... T-10

Adjustment of windshield washer nozzle ......... T-10

Cleaning of windshield washer nozzle ............. T-11

Removal/installation of windshield washer hoseT-11

Removal/installation of rear wiper motor ........ T-11

Check of rear wiper motor ............................... T-11

Removal/installation of rear wiper arm and blade

.......................................................................... T-12

Installation instructions of rear wiper arm ....... T-12

Adjustment of rear wiper arm and blade .......... T-12

Removal/installation of rear washer nozzle ..... T-12

Adjustment of rear washer nozzle .................... T-13

Removal/installation of rear washer hose ........ T-13

Removal/installation of combination instrument ....

.......................................................................... T-13

Essentials to removal of combination instrument ...

.......................................................................... T-13

Disassembly/assembly of combination instrument .

.......................................................................... T-13

Check of combination instrument .................... T-14

Speedometer ..................................................... T-14

Use of input/output inspection mode ............... T-14

Use of speed detector ....................................... T-14

Tachometer ....................................................... T-14

Use of input/output inspection mode ............... T-14

Use of static speed tester .................................. T-14

Fuel gauge ........................................................ T-14

Water temperature gauge .................................. T-15

Repair of combination instrument .................... T-15

Check of fuel gauge sensor .............................. T-15

Removal of water temperature sensor unit ....... T-16

Installation of water temperature sensor .......... T-16

Check of water temperature sensor .................. T-16

Check of oil pressure switch ............................ T-17

Content

Removal/installation of horn ............................ T-17

Tweeter ............................................................. T-17

Low-tone horn .................................................. T-18

Removal/installation horn relay ....................... T-18

Check of horn relay .......................................... T-18

Input/output inspection mode of combination

instrument ......................................................... T-18

Operation procedure ......................................... T-18

Disassembly and assembly of audio assembly . T-38

Removal/installation of 4D loudspeaker .......... T-39

Check of 4D loudspeaker ................................. T-39

Removal/installation of antenna ....................... T-39

Removal/installation of the signal line of front

antenna ............................................................. T-39

Check of the signal line of front antenna ......... T-40

Removal/installation of signal line of rear antenna .

.......................................................................... T-40

Check of rear antenna signal line ..................... T-41

Safety airbag system......................................... T-42

Electrical schematic of safety airbag ................ T-42

Parts relevant to the safety airbag..................... T-43

Fault check of safety airbag ............................. T-43

Fault judgement of safety airbag ...................... T-43

Faults table of safety airbag system ................. T-44

Maintenance procedure of safety airbag .......... T-44

Vehicle disposal procedure of airbag effect...... T-48

Disassembly/assembly of each part of safety airbag

.......................................................................... T-49

Removal/installation of safety airbag module at the

driver side ......................................................... T-49

Disassembly/assembly of clock spring............. T-49

Essentials to installation of clock spring .......... T-50

Adjustment of clock spring .............................. T-50

Removal/installation of the safety airbag module at

the occupant side .............................................. T-50

Disassembly/assembly of safety airbag computer

(ECU) ............................................................... T-51

Warning for maintenance ................................. T-51

Repair of harness .............................................. T-51

Check of safety airbag module ......................... T-52

Operation of safety airbag module ................... T-52

Operation of lateral safety airbag module ........ T-52

Operation of components ................................. T-53

Repeated use of components ............................ T-53

Removal/installation of pretensioning safety belt ...

.......................................................................... T-53

Release procedures of safety airbag module and

pretensioning safety belt .................................. T-53

Driver-sided safety airbag module ................... T-54

Occupant-sided safety airbag module .............. T-54

Pretensioning safety belt .................................. T-55

Release procedure outside vehicle ................... T-55

Driver-sided safety airbag module ................... T-55

Occupant-sided safety airbag module .............. T-57

Pretensioning safety belt .................................. T-58

Released safety airbag module and pretensioning

safety belt ......................................................... T-59

Check of special release tool ............................ T-59

Checking procedure ......................................... T-59

RKE (Remote Control System) ........................ T-61

Removal/installation of remote controller ........ T-61

Reversing radar system .................................... T-61

Removal/installation of reversing radar host.... T-61

Removal/installation of reversing radar sensor T-62

Anti-theft system .............................................. T-63

Removal/installation of anti-theft host controller ...

.......................................................................... T-63

Check of anti-theft host controller ................... T-63

List of terminal voltage (only for reference) .... T-63

Removal/installation of anti-theft coil.............. T-63

Check of anti-theft coil..................................... T-64

Switch and relay ............................................... T-65

Removal/installation of combination switch .... T-65

Disassembly/assembly of combination switch . T-65

Removal/installation of auto lamp switch ........ T-65

Check of auto lamp switch ............................... T-65

Removal/installation of middle switch ............. T-66

Maintenance of middle switch ......................... T-66

Removal/installation of front/rear fog lamp switch

.......................................................................... T-66

Check of front/rear fog lamp switch ................ T-67

Content

Removal and installation of rheostat ................ T-67

Check of rheostat.............................................. T-67

Installation/removal of level adjustment switch

(optional) .......................................................... T-68

Check of level adjustment switch ..................... T-68

Installation/removal of folding switch of rear-view

mirrors (optional) ............................................. T-68

Check of folding switch of rear-view mirrors .. T-69

Removal/installation of power window switch T-69

Removal/maintenance of main power window

switch ............................................................... T-69

Check of main power window switch .............. T-69

Installation/removal of auxiliary power window ....

.......................................................................... T-70

Installation/removal of front door switch ......... T-70

Test of door switch ........................................... T-70

Removal/installation of flasher unit ................. T-71

Test of flasher unit ............................................ T-71

Removal/installation of headlamp relay ........... T-71

Check of headlamp relay .................................. T-72

Removal/installation of front fog lamp relay ... T-72

Check of front fog lamps relay ......................... T-72

Removal/installation of rear fog lamp relay ..... T-72

Check of rear fog lamp relay ............................ T-73

Part of alarm system ......................................... T-73

Removal/installation of horn ............................ T-73

Removal/installation of horn relay ................... T-73

Check of horn relay .......................................... T-74

Disassembly and assembly of clock spring ...... T-74

Essentials to installation of clock spring .......... T-74

Adjustment of clock spring .............................. T-74

Power supply system

T-1

Power supply system

Precautions to fuse use

After the burn-out reason identified and

troubleshooting performed, replace the

burn-out fuse by a specified type of fuse.

Failure to troubleshooting prior to

replacement may make the fuse be blown

again.

Removal/installation of main fuse

1. Remove the negative cable of battery;

2. Remove the cap of main fuse box;

3. Remove as per the order as specified in the

table.

4. The installation procedure is in reverse order

with that of the removal.

1 Nut

2 Main fuse

Removal/installation indoor fuse box

1. Remove the negative cable of battery;

2. Remove the left front interior trim at the driver

side;

3. Remove as per the order indicated in the Table.

4. The installation procedure is in reverse order

with that of the removal.

1 Nut

2 Snap

3 Harness connector

Removal/installation of ignition switch

1. Remove the negative cable of battery;

2. Remove the steering column cover;

3. Remove as per the order indicated in the Table.

4. The installation procedure is in reverse order

with that of the removal.

1 Connector

2 Screw

3 Ignition switch

Check of ignition switch

1. Remove the negative cable of battery;

2. Remove steering column cover;

3. Disconnect the connector of ignition switch;

4. Check, with an ohmmeter, the continuity

between the terminals of ignition switch. If it

fails to meet the technique requirements,

replace the ignition switch.

Continuity

Power supply system

T-2

Removal/installation of key-in reminder

switch

1. Remove the negative cable of battery;

2. Remove the steering column cover;

3. Remove the connector of key-in reminder

switch;

4. Remove the key-in reminder switch.

5. The installation procedure is in reverse order

with that of the removal.

Check of key-in reminder switch

1. Remove the negative cable of battery;

2. Remove the steering column cover.

3. Remove the connector of key-in reminder

switch;

4. Check, with an ohmmeter, the continuity

between the terminals of key-in reminder

switch. If it is non-conforming to the technique

requirements, replace key-in reminder switch.

Removal/installation of cigar-lighter

1. Remove the negative cable of battery;

2. Open the ashtray cover;

3. Remove as per the order indicated in the Table;

4. The installation procedure is in reverse order

with that of the removal.

1 Cigar-lighter plug

2 Socket

3 Anchoring disc of cigar-lighter

4 Plug (harness end)

Connection terminal

Position of ignition

switch

Element side connector (viewed

from the terminal side)

Key-in reminder switch

Steering column lock

Terminal

Continuity

Key position

Inserted key

Non-inserted key

Element side connector (viewed from

the terminal side)

Start

Lock

ACC

On

Lighting system

T-3

Essentials to removal of socket

1. Pass through the socket hole with a flathead

screwdriver wrapped with tape, hold the flange

of ring and turn the socket at the meantime.

2. Push forward the socket;

3. Turn clockwise the socket up to the position as

shown in Fig. and pull it out.

Essentials to removal of ring

1. Press the barb and pull forward the ring.

Check of cigar-lighter

1. Turn the ignition switch to the position of ACC

accessory.

2. Confirm that the cigar-lighter bound out within

10-20s after inserted into the socket. If the

cigar-lighter improperly operates, replace the

plug of cigar-lighter and socket.

Cigar

-

lighter

fixing disc

Ring

Socket

Flange

Section view

Cigar

-

lighter

fixing disc

Hole

Barb

Power supply system

T-4

Lighting and signal system

Headlamp

Removal/installation of headlamp

1. Remove the negative cable of battery;

2. Remove the front bumper;

3. Remove the fixing snaps 1, 2, 3 and 4 and

bolts.

4. Take out the fixture on a suitable place, and

then withdraw manually the plugs 6, 7 and 8

5. The installation procedure is in reverse order

with that of the removal (Note that the

installation procedure is in order of 1, 2, 3 and

4).

6. Adjust the focusing of headlamp (See the

Focusing of Headlamp)

1

Bolt HQ9GG60-0616B

(tightening torque: 7.2～12N·m)

2

3

4

5 Headlamp

6 Headlamp plug

Note: In removing the headlamp, note to first pry up

the clamp on the screw no.2 and avoid breaking up

the clamp while removing it.

Light regulation of headlamp

1. Adjust the tire pressure up to the specified

value.

2. Park a no load vehicle on a level road;

3. Have a person sit down on the driver seat;

4. Park the vehicle perpendicular to the wall;

5. Set the headlamp at 3 m {10 ft} away from the

wall;

6. When adjusting a headlamp, remove the

connector of the other one.

7. Start the engine to charge the battery.

8. As shown in Fig., turn the screw to adjust the

headlamp.

Removal/installation of headlamp bulb

Attention: When used, the halogen bulb will

produce large amount of heat. If the lamp surface is

too dirty, the heat will continue to accumulate and

result in shortening the service life of lamp. Hold

the metal flange instead of glass when replacing the

lamp.

Removal/installation of high/low beam bulbs:

1. Remove the negative cable of battery;

2. Turn on the rear waterproof cover of high or

low-beam, remove the connectors of low-beam

and high-beam; Detach the bulb hold-down

spring and take out the bulb (See Fig. below)

3. The installation procedure is in reverse order

with that of the removal.

Removal and installation of front turn signal lamp

and front position lamp bulbs:

1. Remove the negative cable of battery;

2. Rotate counterclockwise the lamp holder and

take out the bulb.

3. The installation procedure is in reverse order

with that of the removal.

Up/down

adjustment

R/L

adjustment

Lighting system

T-5

1 Turn signal lamp bulb12V 21W(PY21W)

2 High-beam bulb 12V 55W(H7)

3 Waterproof cover

4 Waterproof cover

5 Low-beam bulb 12V 55W(H7)

6 Position lamp bulb 12V 5W(W5W)

Removal/installation of front fog lamps

1. Remove the negative cable of battery;

2. Remove front bumper;

3. Pull out the harness connector;

4. Loosen three fastening screws.

5. Take out the front fog lamps;

6. Install as per the order in reverse with that of

removal.

1

Self-tapping screw HQ9CF60-0516B

(3.9～5.9 N·m)

2

3

4 Front fog lamps

Removal/installation of front fog lamp

bulb

1. Remove front fog lamps;

2. Rotate counterclockwise the bulb holder;

3. Take out the bulb (bulb integrated with the

bulb holder);

4. The installation procedure is in reverse order

with that of the removal.

1 Front fog lamp bulb12V 35W(H8)

2 Front fog lamp

Removal/installation of rear combined

lamps

1. Disconnect battery negative cable;

2. Remove the trunk trim panel;

3. Pull out the plug at the end of taillight harness

4. Loosen two nuts (No.3 and 5 as shown in Fig).

Pull out the taillight along the axis X

5. Pull out the sealing plug on the fixtures harness.

Take out the fixtures.

6. The installation procedure is in reverse order

with that of removal.

1 Rear combined lamps

2 Plastic snap

3

Nut HQ99940-0503 (4.5～7.0 N·m)

4 Location pin sheath

5

nutHQ99940-0503 (4.5～7.0 N·m)

Power supply system

T-6

Attention: When removing the taillight, after

unscrewed the nuts 3 and 5, a certain tension is

required when the taillight is pulled out along the

axis X because there is the location pin sheath No.4,

which is used for fixing the location pin of taillight

Removal/installation of rear combined

lamp bulb

1. Remove rear combined lamps;

2. Unscrew counterclockwise with hand and pull

out the bulb holder of rear combined lamps;

3. Take out the bulb and replace it;

4. Install in the reverse order.

1

Turning lamp bulb12V21W(PY21W)

2

Turning lamp holder

3

Rear fog lamp/backup lamp bulb 12V16W

(W16W)

4

Rear fog lamp/backup lamp holder

5

Rear combined lamps

Note: the brake light and position light are LED

structured. When this part is damaged, it is

necessary to replace the whole rear combined lamps

at a designated maintenance point.

Removal/installation of high-positioned

brake light

1. Remove the negative cable of battery and then

the hole plug;

2. With hand or other tools, take out the fixture

while pressing down the support clamp of high

mounted brake light through bodywork hole.

3. Disconnect the connector; take out the fixture

and replace it.

4 Install in the reverse order.

1 High-positioned brake light

2 Hole cover

3 Hole cover

4 Hole cover

Note: the light source of the high-positioned brake

light is LED. Replace the whole lamp if the source

is damaged.

Removal/installation of license plate lamp

1. Disconnect the negative of power supply;

2. Remove the back door trim panel and then the

cover of license plate lamp.

3. Press out the snap of license plate lamp, with a

straight screwdriver, through the open-hole of

back door inner panel and push out the license

plate lamp;

3. Take out the license plate lamp (two lamps are

identical and in the same direction);

4. Pull out the connector at the harness end;

5. The installation is in reverse order, push

Snap

clipping

Lighting system

T-7

directly, by hand the lamp toward the mounting

hole instead of using a screwdriver.

1 Back door

2 License plate lamp cover

3 License plate lamp

4 License plate lamp

Removal/installation of license plate lamp

bulb

1. Rotate counterclockwise with hand the lamp

holder to the opening position and take it out;

2. Pull out the bulb and replace it;

3. Install in the reverse order.

1 License plate lamp cover

2 Bulb 2V5W (W5W)

3 Bulb holder

Removal/installation of reading light

1. Remove the negative cable of battery;

2. Open the flip of glasses case.

3. Take out two screws with a cross screwdriver.

4. Take out the indoor light from the ceiling;

5. Disconnect connector.

6. The installation procedure is in reverse order

with that of the removal.

1

Self-tapping screw HQ99865-0520B

(torque: not more than 5.9 N·m)

2

3 Reading light holder

4 Glasses case flip

Removal/installation of reading light bulb

1. Remove reading light;

2. Pry with a straight screwdriver the lens of

reading light;

3. Take out the bulb and replace;

4. Install in the reverse order. Install the lens by

holding it pressed and clamped.

1 Lens (R)

2 Lens (L)

Compress the

snap

along the arrow

direction and push

outward

Power supply system

T-8

3 Bulb 12V5W (W5W)

4 Bulb 12V5W (W5W)

5 Reading light holder

Note: The installation structure of reading light on

the ceiling and the replacement of bulb may refer to

the above procedure for maintenance.

Removal/installation of indoor light and

bulb

1. Remove the negative cable of battery;

2. Take out the lens.

3. Take out two screws by use of a cross

screwdriver;

4. Take out the indoor light from the holder;

5. Disconnect connector;

6. The installation procedure is in reverse order

with that of the removal.

Note: When replacing the bulb, just remove the lens

to take out the bulb and replace it.

1 Lens

2 Bulb

3

Bulb 2V 5W (W5W)

4

5

Self-tapping screw HQ99865-0516

(Installation torque: not more than 5.9)

6

Removal/installation of trunk lamp and

bulb

1. Remove the negative cable of battery;

2. Press down one end of the snap with a small

screwdriver through the small hole, so as to

enable the snap come off the ceiling and

obliquely take out the fixture;

3. Disconnect connector;

4. When installing, fit first, the left end of fixture

into the roof and then the right end

Note: The bulb can be removed after the lamp taken

out.

1 Bulb

2 Reading light

Removal/installation of the lighting bulb of

ignition switch

1. Disconnect battery negative cable;

2. Remove the steering column cover;

3. Take out the ignition switch lighting lamp

bulb.

4. The installation procedure is in reverse order

with that of the removal

Snap

Ignition switch

lighting bulb

Lighting system

T-9

Removal/installation of dome lamp bulb

1. Remove the negative cable of battery.

2. Remove the door trim panel.

3. Rotate counterclockwise the bulb holder to the

clamping position and loosen it out.

4. Take out bulb.

5. The installation procedure is in reverse order

with that of removal.

1 Lamp holder at the harness end

2 Bulb

3 Inner trim panel of door

Wiper and washer

T-8

Wiper and washer

Removal/installation of windshield wiper

motor

1. Disconnect battery negative cable;

2. Remove the wiper arm and wiper blade (See

the Removal/Installation of Windshield Wiper

Arm and Wiper Blade).

3. Remove the front wall grille (See the

Removal/Installation of Front Wall Grille);

4. Remove as per the order indicated in the Table;

5. The installation procedure is in reverse order

with that of removal;

6. Adjust the wiper arm and wiper blade (See

Adjustment of Windshield Wiper Arm and

Wiper Blade).

1 Harness connector

2 Bolt

3 Wiper motor

Disassembly/assembly of windshield wiper

motor

1. Disassemble as per the order indicated in the

Table.

2. The assembly procedure is in reverse order of

that of disassembly.

1 Nut

2 Bolt

3 Windshield wiper linkage

Check of windshield wiper motor

1. Disconnect the connector of windshield wiper

motor;

2. Connect the positive voltage of battery with the

terminal D or F and check the operation of

windshield wiper motor as indicated in the

following table.

Terminal Work condition

F High speed

D Low speed

3. When the wiper is operating, remove the

positive connector of battery from the motor

terminal E;

4. Assure the continuous operation of wiper when

it is in the Stop position.

5. Short-circuit the motor terminal E and C and

connect the positive voltage of battery with the

motor terminal E;

6. Confirm that the wiper is operating at low

speed and stops at the Stop position. Replace

the motor of windshield wiper when it is

non-conforming to the technique requirements.

Joint of part (viewed from the

connection terminal side)

Auto-Off Switch

Wiper and washer

T-9

Removal/installation of windshield wiper

arm and wiper blade

1. Remove as per the order indicated in the Table;

2. The installation procedure is in reverse order

with that of removal;

3. Adjust the windshield wiper arm and wiper

blade; (See the Adjustment of Windshield

Wiper Arm and Wiper Blade)

1 Cover

2 Nut

3 Windshield wiper arm

4 Windshield wiper blade

Essentials to installation of windshield

wiper arm

Prior to installing the windshield wiper arm and

clean, with a brush the coupling shaft of windshield

wiper arm;

Adjustment of windshield wiper arm and

wiper blade

1. Start up the motor of windshield wiper and

make the wiper stop at the initial position;

2. Adjust the windshield wiper arm as per the

method shown in the following Fig.

Removal/installation of the fluid reservoir

of washer

1. Disconnect battery negative cable;

2. Partly lift up the right fender;

3. Remove as per the order indicated in the Table;

4. The installation procedure is in reverse order

with that of the removal.

1 Snap

2 Harness connector

3 Front end of washer tube

4 Bolts (2 pcs)

Removal/installation of windshield washer

motor

1. Disconnect battery negative cable;

2. Partly lift up the right fender;

3. Remove washer fluid reservoir.

4. Remove as per the order indicated in the Table;

5. The installation procedure is in reverse order

with that of the removal;

Windshield wiper

coupling shaft

Mark

Wiper and washer

T-10

1

Windshield washer motor (2 pcs)

2

Gasket

Check of windshield washer motor

1. Disconnect battery negative cable;

2. Remove washer fluid reservoir;

3. Connect the positive voltage of battery with the

motor terminal B and the terminal A with the

grounding;

4. Verify the operation condition of windshield

washer motor. Replace the windshield washer

motor if it doesn’t work.

Removal of windshield washer nozzle

1. Remove the acoustic baffle of engine bonnet;

2. Remove the windshield washer hose from the

windshield washer nozzle;

3. Remove the windshield wiper nozzle under the

engine bonnet with a 10mm socket wrench.

Installation of windshield washer nozzle

1. Connect the windshield washer hose with the

windshield washer nozzle;

2. Press down the windshield washer nozzle into

the mounting hole;

3. Adjust the nozzle of windshield washer;

4. Install the acoustic baffle of engine bonnet.

Adjustment of windshield washer nozzle

Insert an needle or similar tool into the nozzle of

windshield washer and adjust the direction of nozzle

as per the method shown in the following Fig.

Side joint of part (viewed from

the connection terminal side)

Windshield wiper nozzle

Deep socket

wrench

Wiper and washer

T-11

Cleaning of windshield washer nozzle

Insert an needle or similar tool into the nozzle of

washer and clean it by pulling forward/backward.

Remove the hose from the nozzle if the nozzle still

plugged after the cleaning. Assure there is sufficient

cleaning fluid and then turn on the washer switch to

wash the interior of hose.

Removal/installation of windshield washer

hose

1. Remove engine bonnet acoustic baffle;

2. Partly lift up the right fender;

3. Remove as per the order indicated in the Table;

4. The installation procedure is in reverse order

with that of removal.

1 Snap

2 Connecting pipe

3 Windshield washer hose

Removal/installation of rear wiper motor

1. Disconnect battery negative cable;

2. Remove rear wiper arm and blade (See the

Removal and Installation of Rear Wiper Arm

and Blade)

3. Remove the inner trim panel of back door (See

the Removal of Inner Trim Panel of Back

Door)

4. Remove in the order as shown in Fig.

5. Install in reverse order with that of removal.

6. Adjust rear wiper arm and blade. (See

Adjustment of rear wiper arm and blade)

1 Outer sleeve

2 Connector

3 Bolt

4 Rear wiper motor assembly

Check of rear wiper motor

1. Disconnect battery negative cable;

2. Remove the inner trim panel of back door;

3. Remove the connector of rear wiper motor;

4. The connector B of rear wiper motor is in

connection with the positive of battery and A

with body metal part for the purpose of

grounding;

5. Be sure that the rear wiper motor is properly

operating;

6 Release the grounding wire of A when

operating on the rear wiper motor.

7. Confirm that the rear wiper parked on the Stop

position. If not, replace the rear wiper motor.

Washer nozzle

Wiper and washer

T-12

Removal/installation of rear wiper arm

and blade

1. Remove in the order as shown in Fig.;

2. Install in reverse order with that of removal;

3. Adjust the rear wiper arm and blade (See the

Adjustment of Rear Wiper Arm and Blade)

1 Guard of rear wiper arm

2 Nut

3 Rear wiper arm

Rear wiper blade

Installation instructions of rear wiper arm

1. Prior to the installation, clean with the wire

brush the arm coupling shaft of rear wiper.

Adjustment of rear wiper arm and blade

1. Enable the rear wiper to operate so as to make

the wiper to stop at the Stop position.

2. Align the wiper arm with the mark.

Removal/installation of rear washer nozzle

1. Disconnect battery negative cable;

2. Remove the washer pipe plug;

3. Remove the connecting hose on the rear

washer nozzle;

4. Press the lock latch on the rear washer;

5. Detach the rear washer nozzle;

6. Install in reverse order with that of removal.

7. Adjust the direction of rear washer nozzle (See

the Adjustment of Rear Wiper Arm and Blade)

Connector at element side

(viewed from the terminal side

Auto

-

Off

Switch

Mark

Wiper and washer

T-13

Adjustment of rear washer nozzle

Insert a needle or similar tool into the spray orifice

on the rear washer nozzle and adjust the direction of

spray orifice.

Removal/installation of rear washer hose

1. Disconnect battery negative cable;

2. Remove necessary trim panel above the right

side wall;

3. Remove the washer hose from the clamp;

4. Partly lift up the right fender and remove the

hose from the clamp;

5. Remove the hose from the washer tank;

6. Install in reverse order with that of removal.

Lock latch

Snap

Washer hose

Washer tank

Page is loading ...

Haima 7 User manual

Haima 7 User manual

Related papers

Other documents