Contec CPS-HBL-8005F Owner's manual

Brand: Contec

Model: CPS-HBL-8005F

Type: Owner's manual

Contec CPS-HBL-8005F is a compact-sized industrial switching HUB with 5 ports for IEEE802.3u(100BASE-TX) / IEEE802.3(10BASE-T) compliant networks. It supports 2-way power supply, reverse wiring protection, and a wide range of temperatures between -20 and +60°C. Its Auto MDI/MDI-X and auto-negotiation features simplify installation and configuration. Additionally, it can be mounted on a 35mm DIN rail, making it suitable for various industrial environments.

CONPROSYS

5 port 10/100M Unmanaged

Industrial Switching HUB

CPS-HBL-8005F

Hardware Manual

CONTEC CO., LTD.

CPS-HBL-8005F

Check Your Package

Thank you for purchasing the CONTEC product.

The product consists of the items listed below.

Check, with the following list, that your package is complete. If you discover damaged or missing

items, contact your retailer.

Product Configuration List

Name

Pcs.

Unit

Setup Guide

Power Supply Connector

Warranty Certificate

Serial Number Label

*The manual of this product can be downloaded from CONTEC website free of charge

(https://www.contec.com/).

To operate this product, a power supply (12-24VDC

5%) is required separately.

For power supply, see Chapter 3, Nomenclature of Components and Their Settings,

“About Power Supply”.

x 2

XXXXXXXXXXXXX

Serial Number Label

Setup Guide

Warranty Certificate

Warranty

Certificate

Power Supply Connector

Main Unit

CAUTION

CPS-HBL-8005F

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep current the information contained in

this document. The information in this document is subject to change without notice.

All relevant issues have been considered in the preparation of this document. Should you notice an

omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may

appear in this document or for results obtained by the user as a result of using this product.

Trademarks

Other brand and product names are trademarks of their respective holder.

CPS-HBL-8005F

iii

Table of Contents

Check Your Package ............................................................................................................................ i

Copyright ............................................................................................................................................ ii

Trademarks ......................................................................................................................................... ii

Table of Contents ............................................................................................................................... iii

1. Before Using the Product 1

About the Unit .................................................................................................................................... 1

Features ........................................................................................................................................ 1

Customer Support ............................................................................................................................... 2

Web Site ....................................................................................................................................... 2

How to Obtain Service........................................................................................................................ 2

Liability ............................................................................................................................................... 2

Safety Precautions .............................................................................................................................. 3

Safety Information ....................................................................................................................... 3

Handling Precautions ................................................................................................................... 3

Environment ................................................................................................................................. 6

Inspection ..................................................................................................................................... 6

Storage ......................................................................................................................................... 6

Disposal........................................................................................................................................ 6

2. Setup of Hardware 7

Mounting on or removing from DIN rail ........................................................................................... 7

Installation Conditions ...................................................................................................................... 11

Installation orientation ............................................................................................................... 11

Spacing between the system unit and any surrounding objects ................................................ 12

3. Nomenclature of Components and Their Settings 13

Names of Components and Functions .............................................................................................. 13

4. Connecting to a Network 17

Network Cables................................................................................................................................. 17

Connecting a Personal Computer, another HUB unit or bridge....................................................... 17

Connection Restrictions with 100BASE-TX Repeater HUBs .................................................. 18

Connection Restrictions with 10BASE-T Repeater HUBs ....................................................... 18

5. System Reference 19

Specifications .................................................................................................................................... 19

Physical Dimensions ......................................................................................................................... 21

CPS-HBL-8005F

1. Before Using the Product

CPS-HBL-8005F

1. Before Using the Product

This chapter provides information you should know before using the product.

About the Unit

This product is a compact-sized industrial switching HUB [25.2(W) x 94.7(D) x 124.8(H) mm] with

5 ports for IEEE802.3u(100BASE-TX) / IEEE802.3(10BASE-T) compliant.

In addition, the Auto MDI/MDI-X features automatic negotiation.

An ideal product for the place where quietness is required as it contains no fan. Moreover, the product

can operate in the temperature between -20 and + 60°C. There are two supplies of power, and

function that prevents power from connecting in reverse.

Please read this manual carefully so that you can build a system by connecting the Switching Hub Unit

to external devices.

Features

- With its compact size, it corresponds to 100BASE-TX in five all ports.

This product contains five ports for IEEE802.3u (100BASE-TX)/ IEEE802.3 (10BASE-T) in the

compact size (25.2(W) x 94.7(D) x 124.8(H) mm).

- 2-way power connector and reverse wiring protection within

The product supports 2-way power supply. Even when one of the power systems fails during the

operation, the product continues functioning.

Our safety design supports the product to function even when wires are connected in reverse.

- Adaptable to a wide range of temperature between -20 and +60°C

The product is capable of operating in the temperature between -20 and + 60°C. It can be installed

in the various environments.

- For Auto MDI/MDI-X feature, auto-negotiation feature

The Auto MDI/MDI-X feature automatically determines straight or cross cable, avoiding wiring

trouble due to wiring mistake.

Moreover, auto-recognition function of communication rates (10/100Mbps) and communication

methods (half/full duplex) by the auto-negotiation feature.

- Installation on DIN rail is possible.

As the product is mounted on the 35mm DIN rail, removing and replacing are easy as well.

- Compatible with 12 - 24VDC wide range power

It is compatible with 12 - 24VDC wide range power and can be used in various power

environment. In addition, An FG terminal is equipped in the power connector.

Optional product

POA201-10-2 : AC adopter (Input: 90 - 264VAC, Output: 12VDC 1.0A)

1. Before Using the Product

CPS-HBL-8005F

Customer Support

CONTEC provides the following support services for you to use CONTEC products more efficiently

and comfortably.

Web Site

https://www.contec.com/

Latest product information

CONTEC provides up-to-date information on products.

CONTEC also provides product manuals and various technical documents in the PDF.

Free download

You can download updated driver software and differential files as well as sample programs available

in several languages.

Note! For product information

Contact your retailer if you have any technical question about a CONTEC product or need its price,

delivery time, or estimate information.

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please

obtain a Return Merchandise Authorization Number (RMA) from the CONTEC group office where

you purchased before returning any product.

* No product will be accepted by CONTEC group without the RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no event will the

warrantor be liable for any incidental or consequential damages due to such defect or consequences

that arise from inexperienced usage, misuse, or malfunction of this device.

1. Before Using the Product

CPS-HBL-8005F

Safety Precautions

Understand the following definitions and precautions to use the product safely.

Safety Information

This document provides safety information using the following symbols to prevent accidents resulting

in injury or death and the destruction of equipment and resources. Understand the meanings of these

labels to operate the equipment safely.

DANGER indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury or in property damage.

Handling Precautions

- Do not use the product where it is exposed to flammable or corrosive gas. Doing so may result in

an explosion, fire, electric shock, or failure.

- Do not allow this device to come into contact with foreign substances (metal particles, flammable

substances, liquids, etc.) This can cause fire or electrical shock.

- Do not place this device in an unstable location or use incomplete mountings. This may cause the

device to fall.

- Be sure to connect the product to the stipulated power supply voltage. Connecting to a different

voltage might cause a fire or electrical shock.

- This product is not intended for use in aerospace, space, nuclear power, medical equipment, or other

applications that require a very high level of reliability. Do not use the product in such applications.

- If using this product in applications where safety is critical such as in railways, automotive, or

disaster prevention or security systems, please contact your retailer.

- The link speed value (e.g., 100Mbps) of the transmission rate used in the Manual (this document) is

the theoretical maximum value of the wired LAN standard and do not indicate the actual data

transmission speed.

- The frame loss could occur depending on the connection destination or installed environment.

- This product contains precision electronic elements and must not be used in locations subject to

physical shock or strong vibration. Otherwise, the board may malfunction, overheat, or cause a

failure.

DANGER

WARNING

CAUTION

DANGER

CAUTION

1. Before Using the Product

CPS-HBL-8005F

- Avoid transporting this products state to shock or vibration that exceeds range of specification.

- Do not use or store the equipment in a hot or cold place, or in a place that is subject to severe

temperature changes. They may cause the malfunction, heat generation, fault, or damage.

- Do not use or store the equipment in a place subject to direct sunlight or near a heating device,

such as a stove. And do not use or store the product near equipment generating a strong magnetic

field or radio waves. They may cause the malfunction, heat generation, fault, or damage.

- Do not use or store this product in the presence of chemicals.

- Use the product in the specified operating condition (temperature, humidity, vibration and shock)

- Please adjust the air current to prevent the reject heat from the product staying around the product.

- Do not use this product in extremely humid or dusty locations. It is extremely dangerous to use

this product with its interior penetrated by water or any other fluid or conductive dust. If this

product must be used in such an environment, install it on a dust-proof control panel, for example.

- If you notice abnormal odor or overheat, please unplug the power cord immediately.

- When you find faults or abnormalities (bad smell or excessive heat), pull the power cord off, then

contact the shop you bought the product or your retailer.

- When using one power supply input, do not touch the unconnected power supply connector. Doing

so may result in electric shock or failure.

- When placing importance on line-noise resistance, use shielded cables to connect to periphery

devices.

- The product could be very hot in the operation. Please do not touch by hands or body. It may

cause burns.

- To avoid electric shock, please do not touch the system with a wet hand.

- Do not open the unit casing. CONTEC will disclaim any responsibility for equipment whose casing

has been opened.

- Do not modify the unit. CONTEC will bear no responsibility for any problems, etc., resulting from

modifying this unit.

- To clean this product, gently wipe it with a soft cloth soaked with water or a neutral detergent. Do

not use benzene, a thinner, or other volatile solvents as they can cause the coating to discolor or

peel off.

- When connecting cables, first check the shapes of connectors (such as LAN connectors), and then

insert them in the correct orientation. After they are connected, do not put too much load on the

connected part. Doing so may result in poor contact or damage to this product and the connected

part.

- Do not touch metal parts or terminals of the product with your hands in operation. Otherwise, this

product may malfunction, overheat, or cause a failure.

- The specification of this product is subject to change without notice for enhancement and quality

improvement. Even when using this product continuously, be sure to read the manual of

CONTEC’s website and understand the contents.

- If you move or transfer the product, make sure to attach the Setup Guide (this document).

- Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever

(including damages for loss of business profits) arising out of the use or inability to use this

CONTEC product or the information contained herein.

1. Before Using the Product

CPS-HBL-8005F

- To use the product in places affected by overcurrent or overvoltage (lightning surge, etc.), select

appropriate surge protection device (SPD) for all entry paths (power line, LAN, ground, etc.). For

selection/introduction/installation of SPD, please consult a specialist.

- When disposing this product, please comply with the municipal regulations and ordinances.

- Always attach the end cover while power is active.

FCC PART15 Class A Notice

EN55032 Class A Notice

Warning: Operation of this equipment in a residential environment could cause radio interference.

The caution when you register UL for your system with this product

-Use POA201-10-2 of the optional products.

NOTE

FCC

WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

1. Before Using the Product

CPS-HBL-8005F

Environment

Use this product in the following environment. If used in an unauthorized environment, the product

may overheat, malfunction, or cause a failure.

Operating temperature

-20 - 60°C

Operating humidity

10 - 90%RH (No condensation)

Corrosive gases

None

Floating dust particles

Not to be excessive

Inspection

Inspect the product periodically to use it safely.

Neither dust nor alien substance should not be attached to the connector’s opening.

Storage

When storing this product, keep it in its original packing form.

(1) Put the unit in the storage bag.

(2) Wrap it in the packing material, then put it in the box.

(3)

Store the package at room temperature at a place free from direct sunlight, moisture, shock,

vibration, magnetism, and static electricity.

Disposal

When disposing of the product, follow the disposal procedures stipulated under the relevant laws and

municipal ordinances.

2. Setup of Hardware

CPS-HBL-8005F

2. Setup of Hardware

Mounting on or removing from DIN rail

Before installing the product, you need to unlock the fixed hooks of the product.

How to unlock fixed hooks -1

(1)

Stick a slotted screwdriver (the point should be smaller than 4.5mm) into a hole.

(see the figure below)

Figure 2.1. Unlock the fixed hooks-1 < 1 / 2 >

(2) By using the screwdriver as leverage, move it upward in the direction of the arrow to unlock.

Figure 2.1. Unlock the fixed hooks-1 < 2 / 2 >

Protrusion to use as the

screwdriver's fulcrum

Precision slotted

screwdriver

(point: 4.5mm or smaller)

insertion hole

Using this point as the fulcrum,

move the fixed hook by way of

the principle of leverage.

2. Setup of Hardware

CPS-HBL-8005F

How to unlock fixed hooks -2

If your slotted screwdriver is not suitable for the hole.

(1) Place the slotted screwdriver (the point should be smaller than 8mm) as shown in the figure.

Figure 2.2. Unlock the fixed hooks-2 < 1 / 2 >

(2) Rotate the screwdriver 90-degree in either direction.

Figure 2.2. Unlock the fixed hooks-2 < 2 / 2 >

Insert the slotted screwdriver (point: 8mm or smaller)

into the position shown in the figure

(between the casing and the arch of the fixed hook).

Rotate the slotted screwdriver.

2. Setup of Hardware

CPS-HBL-8005F

How to mount the product

(1) Pull down the fixed hook at the bottom to unlock. The top hook should remain locked.

Figure 2.3. Mount the product on the DIN Rail < 1 / 3 >

(2) Hang the product on the upper part of the DIN rail, and press it to the lower side of the DIN rail.

Figure 2.3. Mount the product on the DIN Rail < 2 / 3 >

(3) Push up the hook to lock.

Figure 2.3. Mount the product on the DIN Rail < 3 / 3 >

The product could also be mounted with the top hook unlocked and bottom hook remains locked.

2. Setup of Hardware

CPS-HBL-8005F

Confirm whether the product has been securely mounted onto the DIN rail.

How to remove the product

Take off LAN cables and power cables connected to the product before removing from the DIN

rail.

(1) Pull down the fixed hook at the bottom to unlock.

Figure 2.4. Remove the product from the DIN Rail < 1 / 2 >

(2) Pull the lower part of the product toward you and lift it up to remove.

Figure 2.4. Remove the product from the DIN Rail < 2 / 2 >

The product could also be removed by unlocking the top hook.

CAUTION

2. Setup of Hardware

CPS-HBL-8005F

Installation Conditions

Even within the temperature specification range, make sure the heat in the product can let off

adequately in the case of high temperature environment application.

Installation orientation

Avoid installation on unsuitable installation directions as insufficient heat dissipation may occur.

Suitable

installation

directions

(Top)

(Bottom)

Unsuitable

installation

directions

(Top)

(Bottom)

(Top)

(Bottom)

Figure 2.5. Installation direction

Floor

Ceiling

2. Setup of Hardware

CPS-HBL-8005F

Spacing between the system unit and any surrounding objects

Do not locate the module in a fully enclosed housing.

DIN rail mounted

Secure a distance of at least 50mm between the top/bottom of the main product and any surrounding

objects and also a distance of at least 50mm between each side of the product and any surrounding

objects (5.8mm for the product overview level side).

Figure 2.6. Spacing between the product and surrounding objects when mounting on the DIN

rail

3. Nomenclature of Components and Their Settings

CPS-HBL-8005F

3. Nomenclature of Components and Their

Settings

Names of Components and Functions

Figure 3.1 shows the nomenclature of components.

Figure 3.1. Names of Components

Table 3.1. LED Indicators

Name

Color

Content of Display

POWER LED

Green

ON : Power on

OFF : Power off

SPEED LED

Yellow - green

ON : Indicates linking by 100Mbps

OFF : Indicates linking by 10Mbps or not linked.

LINK/ACT LED

Green

ON : Linking

Flashing : indicates data sending/ receiving with

connected external devises

OFF : No Linking

SPEED LED

LINK/ACT LED

10BASE-T/100BASE-TX port

Power supply connector

POWER LED

3. Nomenclature of Components and Their Settings

CPS-HBL-8005F

Table 3.2. Connectors

Name

Function

Power supply

Connector

Acceptable connector : 15EDGK-3.5-03P-13-1000AH, 15EDGK-3.5-03P-14-1000AH

(DEGSON ELECTRONICS)

The correspondence cable is AWG28-16.

(Cable length should meet the specification of the power supply.)

You can connect cables with screws.

The product can function by one of the power connecters.

Even when one power turns off during the operation, the product keeps functioning.

Power Supply Connector

15EDGRC-THR-3.5-03P

(DEGSON ELECTRONICS)

Pin Number

Signal

Description

Vi+

Power (12-24VDC±5%)*1

Vi-

Power(GND)*1

Frame Ground

*1 The product will function even when Vi+, Vi- are connected in reverse.

Table 3.3. 10BASE-T/100BASE-TX port

Name

Function

10BASE-T/

100BASE-TX

port

Ports 1 - 5

This port is for connecting the PC (LAN adapter)

and other HUB units and bridges.

Auto-negotiation of communication rates (10Mbps/100Mbps), and communication

methods (Half/Full duplex) by Auto MDI/MDI-X function, straight cable and the

cross cable are recognized automatically.

Connector 7588-B344-2300-DT2-B0B ,

7588-B314-2000-DT2-B0B

(POWERWAY ELECTRONICS)

Pin number

Signal

Description

TXP

Transmission(+)

TXN

Transmission (-)

RXP

reception (+)

4 ---

unused

5 ---

unused

RXN

reception (-)

---

unused

---

unused

Vi-

- 24VDC

3. Nomenclature of Components and Their Settings

CPS-HBL-8005F

About of Power Supply

For power supply, use the power supply that rises within an input voltage range of 11.6VDC or higher

within 50msec. The power supply that cannot meet this requirement may cause device failure or

accident.

Figure 3.2. Graph of Rise Time of Power Supply

Time (ms)

Input voltage

()

25.2

11.6

Page is loading ...

Contec CPS-HBL-8005F Owner's manual

Contec CPS-HBL-8005F Owner's manual

Contec CPS-HBL-8005F Owner's manual

Related papers

Other documents