9 9
User Maintenance Instructions
This appliance requires little maintenance. It contains no user serviceable parts. Do not try to repair it yourself.
Contact a qualied appliance repair technician if the product requires servicing.
Care & Cleaning Instructions
CAUTION: Never immerse the motor base, plug or cord in water or any other liquid.
1. Always unplug the Rocket Extract Pro Plus Blender before cleaning.
2. Whenever possible, rinse attachments and accessories immediately after processing for both sanitary
reasons and to make cleanup easier.
3. Always handle blades using the blade collar.
CAUTION: Use extreme care when handling blades. Do not touch the blades with your ngers. The blades
are very sharp and can cause injury if touched.
IMPORTANT! All blade attachments: blending blade or chopping blade blade include a seal ring that
creates an airtight seal during processing. Always check to be sure the ring is present
and properly tted into the collar before use.
4. For quick clean-ups, ll the blender jar or any tumbler 1/4 full with clean, warm water. Following the steps
outlined in the Operating Instructions, process on LOW for 5 seconds. Rinse and dry thoroughly.
5. If necessary, soak blades in soapy water for 10 to 15 minutes. Use any small nylon bristle brush to remove
processed food from the blade and the blade area.
6. Wash all lids and tumbler rings in warm soapy water. Rinse and dry thoroughly.
CAUTION: Never use rough scouring pads or abrasive cleansers on any plastic or metal parts as the
surface may be damaged.
7. All attachments and accessories, except for the motor base, are top-rack only dishwasher safe.
8. The motor base may be wiped with a damp cloth or sponge. Dry thoroughly.
WARNING: DO NOT IMMERSE THE MOTOR BASE IN WATER.
Storing Instructions
1. Unplug and clean blender.
2. Store in original box or in a clean, dry place.
3. Never store the Rocket Extract Pro Plus Blender immediately after use or while it is plugged in.
4. Never wrap cord tightly around the appliance. Never place any stress on cord, especially where the cord
enters the motor base, as this could cause the cord to fray and break.
Troubleshooting
Problem Cause Solution
When a PRE-PROGRAMMED/
SPEED button is pressed,
all lights on the control panel
begin to ash. Rocket Extract
Pro Plus Blender will not
operate.
Blender jar or tumbler is
not correctly assembled
onto the motor base.
• Press the ON/OFF button to reset. Reposition blender jar or
tumbler. Align 3 locking tabs on the blade collar with 3 slots
on the motor base. Press down rmly on the blender jar lid or
tumbler and turn clockwise until the tabs lock into position.
• Press any PRE-PROGRAMMED/SPEED button to
resume operation.
The blender motor rotates very
slowly.
Blender jar or tumbler is
overloaded.
• Remove some food from the tumbler or the blender jar and
continue blending.
• Add liquid to the blender jar or tumbler and continue blending.
Ingredients are not mixing
together well.
Heavier ingredients have
fallen to the bottom.
• If necessary, remove blender jar or tumbler and shake
ingredients to re-distribute. Continue blending.
• If the puree is still not blended smoothly, it may be necessary
to add liquid to the blender jar or tumbler and continue blending.
The Rocket Extract Pro Plus
Blender has stopped operating.
All control panel lights are
ashing.
• A hard or brous
ingredient, such as a chunk
of carrot or celery can
get stuck in the blade and
prevent it from turning.
• The motor is overheated.
• Remove the blade attachment and remove any debris,
if necessary. Stir food and replace blade.
• Allow the Rocket Extract Pro Plus Blender to rest for at least
3 minutes. Then replace blender jar or tumbler and continue
blending.
SO-311573_14285 BELLA REPP Blender IM R1.indd 9 2014-05-14 12:42 PM