Bradley Terreon Quadra-Fount Washfountain MF2944/TT Installation Instructions Manual

Brand: Bradley

Model: Terreon Quadra-Fount Washfountain MF2944/TT

Category: Sanitary ware

Type: Installation Instructions Manual

This manual is also suitable for

Terreon Tri-Fount MF2933/IR

Bradley Multi-Fount™ Series

MF2944/TT

Terreon

Quadra-Fount

Washfountain with Touch

Time® Control

(Standard* & Juvenile Height)

*Standard Height is ADA Compliant

Installation

Instructions

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . . . . .2

Washfountain Components List . . . . . . . . . . . . . . . .3

Installation Instructions . . . . . . . . . . . . . . . . . . .4-10

Cleaning and Maintenance . . . . . . . . . . . . . . . .11-12

Solenoid Valve Troubleshooting . . . . . . . . . . .13-14

Thermostatic Mixing Valve Troubleshooting . .15-16

215-1539 Rev. A; EN 03-063

Page 1 of 16 12-18-2003

P.O. Box 309, Menomonee Falls, WI 53052-0309

TEL. 1-800-BRADLEY FAX 262-251-5817

http://www.bradleycorp.com

IMPORTANT

Read through this installation manual to

ensure proper installation.

Make sure that water supply is completely

off before installation is begun.

When drilling into tile, masonry, or other

hard materials to install wall and floor

anchors, be sure to wear safety goggles to

prevent eye injuries.

Wall anchors used must have a minimum

pull-out rating of 1,000 lbs.

The Quadra-Fount® requires a water

flowing pressure of at least 20 psi, but no

greater than 80 psi.

File these instructions with the owner or

maintenance department.

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

MF2944/TT Installation Instructions

Bradley Corporation • 215-1539 Rev. A; EN 03-063

2 12-18-2003

Pre-Installation Information

Terreon

material

The Quadra-Fount® features Terreon

, a durable solid surface material used on the bowl and

pedestal. Terreon

resists stains, burns and impact, and is repairable with everyday cleaners or fine-

grit abrasives.

Touch Time and solenoid valve

Each Touch Time pushbutton activates a flow of water. Each nozzle is controlled by a separate

solenoid valve, allowing each user to activate a flow of tempered water from one spray nozzle with a

pushbutton for 15 seconds. Each valve uses less than half the maximum amount of hot water allowed

by the ANSI/ASHRAE/IES 90A-1980 Standard.

Solenoid valve: An electronically controlled solenoid valve serves as the metering mechanism. Few

moving parts provide reliable metering performance and the solenoid is unaffected by chemicals and

minerals often present in municipal water supplies.

Barrier-free and ADA compliant

The Terreon® Quadra-Fount® with Touch Time is designed to comply with all ADA guidelines on

reaches, clearances and operation when mounted at standard height dimensions by the installer (see

page 4 of this instruction manual for rough-in and mounting dimensions).

Terreon® Quadra-Fount® Washfountain Warranty Information

Bradley Corporation warrants to commercial and institutional purchasers only each unit free from

defects in material and workmanship under normal use and service upon the following terms and

conditions.

1. This warranty is limited to replacing or repairing, at our option, transportation charges prepaid

by the purchaser, any Bradley unit or part thereof which our inspection shall show to have

been defective within the limitations of this warranty.

2. The period during which Terreon

Quadra-Fount® components are warranted is as follows:

• Terreon

side panels, bowl, and top cover warranted for 5 years.

• All other Quadra-Fount® components warranted for 1 year.

3. This warranty does not cover installation or any other labor charges and does not apply to any

units which have been damaged by accident, abuse, improper installation or improper

maintenance.

4. The replacement or repair of defective units as stated in this warranty shall constitute the sole

remedy of the purchaser and the sole liability of Bradley Corporation under this warranty.

Bradley Corporation shall not otherwise be liable under any indirect damages caused by

defects in the repair or replacement thereof.

5. This warranty extends only to commercial and institutional purchaser and does not extend to

any others, including consumer customers of commercial institutional purchasers.

6. This warranty is in lieu of all other warranties, expressed or implied, including any implied

warranty of merchants ability or fitness for a particular purpose or otherwise.

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

Installation Instructions MF2944/TT

Bradley Corporation • 215-1539 Rev. A; EN 03-063

12-18-2003

Solenoid Assembly with

Two Mounting Screws

TEMPERED LINE

S45-2081 (OPTIONAL)

Stop/Check

Hose

VALVE PREPACK S45-2082

Stop/Check

Hose

Parts Included with the Quadra-Fount®

Separate all parts from packaging materials and ensure you have all the parts required for assembly.

If any parts are missing, do not attempt to assemble the Quadra-Fount® until you obtain all parts.

Supplies required:

• (6) 3/8" diameter bolts with washers and (6) wall anchors appropriate for your installation

• (2) 3/8" diameter bolts with washers and (2) floor anchors appropriate for your installation

• 1/2" NPT Hot and cold water supply lines

• Drain trap and waste connection

• Pipe sealant and plumber’s putty

• 110 VAC power source for 110/24 VAC plug-in transformer supplied

• OPTIONAL: Bradley recommends installing an electrical cut-off switch to the unit. This

feature prevents accidental water delivery during regular maintenance and service.

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

MF2944/TT Installation Instructions

Bradley Corporation • 215-1539 Rev. A; EN 03-063

4 12-18-2003

Installation Instructions

Step 1: Install the 24 VAC transformer

CAUTION: The Quadra-Fount® must be connected with a 24 VAC Class II plug-in

transformer. Connection with 110 VAC will result in damage to the

electronics and could result in personal injury.

IMPORTANT: Consult local electrical codes for the mounting location of the 110/24

VAC Class II plug-in transformer.

IMPORTANT: Compliance and conformity to local codes and ordinances is the

responsibility of the installer.

Step 2: Rough-in piping and install wall anchors

NOTE: See Figure 1 for piping rough-in dimensions and wall anchor locations.

IMPORTANT: Make sure that the water is completely shut off before beginning

installation.

1. Rough-in hot and cold supply lines through the wall or floor.

2. Rough-in a drain waste connection through the wall or floor.

IMPORTANT: Wall anchors need to withstand 1000 lb. pull force.

(178)

5-1/8" *

(130)

(51)

11"

(279)

11"

(279)

17-1/2" *

(445)

24" *

(610)

21-3/4"

(552)

28" *

(711)

7-1/2"

(191)

(178)

(203)

110V GFI ELECTRICAL

OUTLET RECOMMENDED

LOCATION (REFER TO LOCAL

CODES BEFORE ROUGH-IN)

FINISHED FLOOR

1-1/2" NPT WASTE CONNECTION

THROUGH FLOOR - 3" FROM WALL

1/2 NPT SUPPLIES - 5" FROM WALL

STUB OUT MIN. 1-1/2"

FROM FLOOR

1/2 NPT SUPPLIES

STUB OUT MIN. 1-1/2"

FROM WALL

1-1/2 NPT WASTE CONNECTION

FOR USE WITH 1-1/2" TUBULAR P-TRA

STUB OUT MIN. 1-1/2"

(2) APPROPRIATE ANCHORS

AND 3/8" BOLTS (SUPPLIED

BY INSTALLER TO MOUNT

BOWL TO WALL

Figure 1

* Subtract 4" from this dimension for juvenile height model.

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

Installation Instructions MF2944/TT

Bradley Corporation • 215-1539 Rev. A; EN 03-063

12-18-2003

Installation Instructions continued . . .

Step 3: Assemble pedestal

NOTE: Washers are not utilized on back of mounting panel. Refer to Figure 2 when assembling

pedestal.

1. Fasten the mounting panel to the pedestal with four pan head 1/4"- 20 x 1/2" screws supplied.

2. Install the upper bracket to the pedestal panels with two pan head 1/4"- 20 x 1/2" screws and

5/16" I.D washers supplied.

3. Install the lower bracket to the pedestal panels with two pan head 1/4"- 20 x 1/2" screws and

5/16" I.D. washers supplied.

Figure 2

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

MF2944/TT Installation Instructions

Bradley Corporation • 215-1539 Rev. A; EN 03-063

6 12-18-2003

Installation Instructions continued . . .

Step 4: Install pedestal

NOTE: Refer to Figure 3 when installing pedestal.

1. Measure and mark the centerline of the washfountain on the wall and floor.

NOTE: Before mounting the pedestal to the floor, make sure the floor is level. If it is not level, be

prepared to install shims when positioning the pedestal in step 2.

WARNING: Do not attempt to install the pedestal by yourself. To prevent serious

injury, install the pedestal with the assistance of another person and

always use appropriate lifting procedures.

2. With someone to assist you, move the pedestal assembly to the wall using appropriate lifting

procedures and align the locating notches on the mounting panel with the centerline marked on

the wall. If the floor is not level, install shims under the left and/or right pedestal.

NOTE: Remove molding strips or tiles which could prevent mounting unit flush to the wall.

3. Drill holes in the wall through the four 1/2" diameter holes in the mounting panel and install four

anchors (supplied by installer) for 3/8" diameter bolts.

4. Secure the pedestal assembly to the wall anchors using four 3/8" diameter bolts and washers

(supplied by installer).

5. Drill holes in the floor through the two 1/2" diameter holes in the lower bracket and install two

anchors (supplied by installer) for 3/8" diameter bolts.

6. After floor anchors are installed, secure the pedestal assembly to the floor anchors using two 3/8"

diameter bolts and washers (supplied by installer).

Figure 3

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

Installation Instructions MF2944/TT

Bradley Corporation • 215-1539 Rev. A; EN 03-063

12-18-2003

Installation Instructions continued . . .

Step 5: Install solenoid assembly

1. Connect the 1/2" NPT female end of the stop/check valves to the rough-ins.

2. Connect the supply hoses to the stop/check valves.

3. Inside the pedestal, install the two 1/4-20 x 1/2" screws (supplied with solenoid assembly) in the

mounting holes on the side of the left pedestal panel. DO NOT thread the screw completely

into the panel, but allow 5/16" of the screw to be exposed (see Figure 4)

4. Mount the valve bracket to the left side of the pedestal as shown.

IMPORTANT: The hose attached to the hot water inlet of the Navigator® TMV

valve (marked with “H”) must be connected to the hot water rough-in.

5. Connect the supply hoses to the Navigator® TMV valve.

6. FOR OPTIONAL SINGLE TEMPERED SUPPLY: Attach the stop/check/valve to the 1/2" tempered

supply line. Connect the stop/check/valve to the solenoid valve with the flexible supply hose.

NOTE: The thermostatic mixing valve requires at least 115° F water from the hot water side for

proper operation. As with all lavatories, there will be a delay in obtaining warm water. If the hot

water is too far away from the washfountain, a circulating pump may be required.

Braided Hose

Cold Supply Inlet

Hot Supply

Inlet

Stop/Check Valve

Navigator® TMV

Solenoid Valve Assembly

1/4-20 x 1/2" Screws

Figure 4

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

MF2944/TT Installation Instructions

Bradley Corporation • 215-1539 Rev. A; EN 03-063

8 12-18-2003

Installation Instructions continued . . .

Step 6: Assemble and install bowl

WARNING: Do not attempt to install the bowl by yourself. To prevent serious injury,

install the bowl with the assistance of another person and always use

appropriate lifting procedures.

1. Install two 3/8" wall anchors (supplied by installer) which will be used to mount the bowl to the

wall. (See Figure1 on page 4).

2. Carefully remove the sprayhead cover (see Figure 9 on page 10)

3. With the help of an an assistant, carefully lift the bowl on the pedestal frame using appropriate

lifting procedures. Ensure bowl remains 3 - 4 inches from the wall.

WARNING: Do not leave the bowl on the pedestal unsupported, as it may fall and

cause personal injury or damage to property.

4. Install the 2 wall anchor brackets to the back of the bowl using the 3/8-16 x 2" hex head bolts,

13/32" I.D. plain washers, anchor plates, lockwashers and hex nuts provided as shown in Figure 5.

5. Uncoil the Touch Time switch leads and plastic tubing from the rear of the backsplash.

6. Slide the bowl back to the wall and secure the bowl’s wall brackets to the wall anchors with two

3/8" diameter bolts and washers (supplied by installer)

7. Fasten the bowl to the upper bracket on the pedestal assembly with two pan head

1/4"- 20 x 1/2" screws and washers supplied.

8. Install the drain spud in the bowl using plumber’s putty (see Figure 6).

NOTE: Discard rubber gasket included with drain spud. It cannot be used in this application.

9. From beneath bowl, thread the locknut with the spud washer onto the drain spud and tighten the

locknut against the bowl.

10. Install strainer in the bowl drain using the two #10-24 x 1/2" oval Phillips head screws supplied.

11. Connect the drain trap (supplied by installer) to the drain spud and drain line.

Figure 5

Figure 6

Spud

Washer

#10-24 x 1/2"

Screw for

Strainer

Drain

Spud

Dome

Strainer

Discard this

washer; it is not

used on

washfountains.

Washfountain

Bowl

Spud

Locknut

Drain Assembly

Back View of Washfountain Bowl

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

Installation Instructions MF2944/TT

Bradley Corporation • 215-1539 Rev. A; EN 03-063

12-18-2003

Installation Instructions continued . . .

Step 7: Electrical and supply connections

WARNING: The Touch Time control must be connected with a 24 VAC Class II

transformer. Connections to 110 VAC can cause personal injury and

will result in damage to the electronics.

CAUTION: Connection of leads other than shown may cause permanent damage

to the sensor.

IMPORTANT: Compliance and conformity to local codes and ordinance is the

responsibility of the installer.

1. Connect the wires per the wiring diagram shown below.

2. Insert four different colored sprayhead supply tubes into four solenoid tube connectors, as shown

in Figure 7, by loosening tube connector cap and firmly pushing tubing into tube connector until

the tubes are fully seated, then re-tighten connector cap.

Supply Inlet

Navigator® Mixing

Valve

Solenoid

Assembly

Transformer

S83-134

Green Supply Tube

(From Sprayhead)

Red Supply Tube

(From Sprayhead)

Black Supply Tube

(From Sprayhead)

Yellow Supply Tube

(From Sprayhead)

Left

Button

Compression

Nut

Compression

Nuts

Brown Wires

Black Wires

Green Wires

Gray Wires

Left

Center

Button

Right

Center

Button

Right

Button

Gray

Green

Black

Brown

Figure 7

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

MF2944/TT Installation Instructions

Bradley Corporation • 215-1539 Rev. A; EN 03-063

10 12-18-2003

Installation Instructions continued . . .

IMPORTANT: Verify that power to your Quadra-Fount® is 24 VAC!

Step 8: Check Operation

1. Check to make sure both stop/check valves are open (see Figure 4 on page 7).

2. Turn on the main water supply to the Quadra-

Fount® and check for leaking.

3. Turn on the electrical power and depress each

Touch Time pushbutton until air is purged from

the lines.

NOTE: The Navigator® TMV valve is NOT factory

preset. Upon installation, the temperature of this

valve must be checked and adjusted to ensure

delivery of a safe water temperature. Water in

excess of 110°F (43°C) may cause scalding.

4. Check the temperature when approximately 1.0

GPM water flow is reached and adjust if

necessary (the range of the valve is 95°F–115°F

(35°C–43°C). To adjust the temperature, follow

the procedure below:

• Loosen temperature locking nut with wrench.

• Using a blade screwdriver, turn the adjustment

stem counterclockwise to increase the

temperature or clockwise to decrease the

temperature (Figure 8).

• Once desired temperature is reached, tighten nut

to prevent temperature change.

Step 9: Install Top Cover

1. Carefully place the top cover with threaded rods

on top of washfountain sprayhead (see Figure 9).

2. Inside the pedestal assembly of the washfountain

(use front access), slide the anchor plate onto the

threaded rods and secure anchor plate against

bowl using the wing nuts provided.

3. To install front panel, slip holes in bottom of

front pedestal panel over the two pins on the

lower bracket (see Figure 10)

4. Secure panel to upper bracket with attached

screw.

Figure 10

Figure 9

TEMPERATURE

ADJUSTMENT

STEM

TEMPERATURE

LOCKING

NUT

Figure 8

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

Installation Instructions MF2944/TT

Bradley Corporation • 215-1539 Rev. A; EN 03-063

12-18-2003

Cleaning and Maintenance Instructions for Terreon®

Material Description: Terreon

is a NAHB Certified densified solid surface material composed of polyester

resin and is resistant to chemicals, stains, burns and impact. Surface damage can be easily repaired with

everyday cleansers or fine grit abrasives.

Routine Cleaning: Clean daily or as often as conditions require using a standard commercial or household

cleaner such as Formula 409

or Windex

Stubborn Stains: Remove tough stains with Ajax

, Comet

, or Soft-Scrub

and a green Scotch-Brite

pad or

lightly sand in a circular motion with 240 grit wet/dry sandpaper. The finish can be renewed with a maroon

Scotch-Brite pad.

Special Situations for Material

Scratches: Remove scratches with a green Scotch-Brite

pad. The finish can then be renewed with a maroon

Scotch-Brite

pad.

Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse

the unit thoroughly after cleaning.

Restoring the surface: Use Hope's

Solid Surface cleaner and polish to refresh and protect the Terreon

Solid Surface material.Bradley recommends additional care and maintenance for the darker colored Terreon,

for complete instructions on this additional maintenance see Bradley document #1505.

IMPORTANT: DO NOT USE STRONG ACID OR ALKALINE CHEMICALS AND

CLEANSERS TO CLEAN TERREON. IF THESE CHEMICALS COME IN

CONTACT WITH THE TERREON SURFACE, WIPE THEM OFF

IMMEDIATELY AND RINSE WITH SOAPY WATER.

AVOID CONTACT WITH HARSH CHEMICALS SUCH AS PAINT REMOVER,

BLEACH, ACETONE, ETC. AVOID CONTACT WITH HOT PANS AND

OBJECTS.

Repair Kits: Terreon

repair kits are available. Contact your Bradley representative or distributor for part

numbers and pricing.

NOTE: Repair kits are made to order and have a shelf life of 30 days.

Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an

endorsement, or does the omission of any brand name cleaner imply it’s inadequacy. Many products named are

regional in distribution, and can be found in local supermarkets, department and hardware stores, or through

your cleaning service. It is emphasized that all products should be used in strict accordance with package

instructions.

NOTE: When cleaning units equipped with infrared (electronic eye) activation, it is helpful to turn off

the power to the unit or cover the windows to prevent accidental activation. After the window is

covered, the water will run for approximately 30 seconds and then shut off.

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

MF2944/TT Installation Instructions

Bradley Corporation • 215-1539 Rev. A; EN 03-063

12 12-18-2003

Cleaning and Maintenance Instructions for Stainless Steel

Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive.

Proper care, particularly under corrosive conditions, is essential. Always start with the simplest solution and

work your way toward the more complicated.

Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or

ammonia. Apply the cleaning solution per the manufactures instructions and always use a soft cloth or

sponge to avoid damaging the finish.

Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball

stainless steel cleaner or a soft abrasive. Always follow the manufactures instructions and apply in the same

direction as the polish lines.

IMPORTANT: NEVER USE ORDINARY STEEL WOOL OR STEEL BRUSHES ON

STAINLESS STEEL. ALWAYS USE STAINLESS STEEL WOOL OR

STAINLESS STEEL BRUSHES.

Special Situations for Material

Finger Prints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and

polish in accordance with the manufactures instructions. Many of these products leave a protective coating

the helps prevent future smears and fingerprints.

Grease and Oil : To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in

accordance to the manufactures instructions and in the direction of the polish lines.

Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents),

thiocyanates (pesticides, photography chemicals, and some foods), and iodides on stainless steel equipment,

especially if acid conditions exist.

IMPORTANT: DO NOT PERMIT SALTY SOLUTIONS TO EVAPORATE AND DRY ON

STAINLESS STEEL.

The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the

actual source of the rust in some iron or steel particles which may be touching, but not actually a part of the

stainless steel structure.

NOTE: Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear. The use of

these cleaners should be avoided.

Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an

endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named

are regional in distribution, and can be found in local supermarkets, department and hardware stores, or

through your cleaning service. It is emphasized that all products should be used in strict accordance with

package instructions.

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

Installation Instructions MF2944/TT

Bradley Corporation • 215-1539 Rev. A; EN 03-063

12-18-2003

Solenoid Valve Troubleshooting

CAUTION: Turn off water supplies to unit before troubleshooting.

Problem: An individual operating station fails to shut off and drips.

Cause: There is debris trapped between the diaphragm and the valve seat.

Solution: Remove debris between diaphragm and the valve seat.

1. Remove the three #8 Phillips-head screws that hold the solenoid valve assembly together. Be

careful not to lose the armature or spring (see Figure 11 on page 14).

2. Remove the diaphragm. Remove any particles that have been trapped between the diaphragm

and the valve seat. Rinse off the diaphragm and inspect for damage. Make sure the center orifice

and both small side orifices are open.

3. Reassemble in reverse order, being careful not to overtighten the Phillips-head screws or you

may crack the plastic valve body. Tighten until the armature plate makes contact with the plastic

body.

4. Reconnect the wiring per diagram on page 9.

Problem: An individual operating station fails to turn on.

Cause: A failed coil for the valve or loose electrical connection to the terminal.

Solution: Test the station to determine cause.

1. Disconnect the wires from the coil of an adjacent valve. Disconnect the wires from the problem

valve and reconnect to the adjacent valve.

2. Turn on electrical and water supplies to the unit. Depress the Touch Time pushbutton of the

problem station, the adjacent station should turn on.

If the adjacent station turns on and cycles normally, replace the coil on the problem valve.

If the adjacent valve fails to turn on, inspect the wires from the sensor cable and do the following:

• make sure there are no breaks and that the fully insulated disconnect terminals are firmly

crimped in place;

• turn off the electrical and water supplies;

• reconnect to the adjacent valve and turn on the water supplies to the unit;

• depress the Touch Time pushbutton. If the station still fails to turn on, replace the sensor.

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

MF2944/TT Installation Instructions

Bradley Corporation • 215-1539 Rev. A; EN 03-063

14 12-18-2003

Solenoid Valve S07-068 (closed body) and S07-068A (thru body)

DESCRIPTIONQTY. PART NO.REF.

1 1 118-307 VALVE BODY, 1/4" CLOSED

2 1 269-983 DIAPHRAGM

3 1 269-577 ARMATURE

4 1 269-578 SPRING

5 1 269-1729 ARMATURE HOUSING

6 1 269-1730 CLAMP, ARMATURE HOUSING

7 1 269-579 COIL, SOLENOID VALVE

8 3 160-447 SCREW, #8 X 5/8

9 1 125-001CS O-RING, #2-013

10 1 125-160 FLOW RESTRICTOR, .5 GPM

1 1 118-307A VALVE BODY, 1/4" THRU

Figure 11

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

Installation Instructions MF2944/TT

Bradley Corporation • 215-1539 Rev. A; EN 03-063

12-18-2003

Thermostatic Mixing Valve Troubleshooting

NOTE: Before attempting to troubleshoot the valve or disassemble the components, check for the

following conditions:

• If stop/check valves are used, make sure that they are fully open.

• Make sure that the hot and cold inlet pipes are connected properly, and that there are no cross-

connections or leaking stop/check valves.

• Check the hot water heater output to make sure that it is at least 20° F above the set

temperature.

Be sure to close the appropriate shut-off valves prior to disassembly of the valve and reopen the

valves after inspection and repair is complete.

Problem: Limited water flow

Cause: Dirt and debris have built up in the valve or strainer.

1. Remove and clean strainer. If strainer needs to be replaced, order Bradley part no. 173-028.

2. Check the piston for smooth movement.

To check the valve's piston for free and smooth movement, follow the procedures outlined below:

1. Remove the valve's cap and thermostat (see Figure 12 on Page 16).

2. Push down on the piston with your finger (the piston should move freely). If the movement is

not as it should be, the piston needs to be cleaned. Follow the method outlined below for

cleaning the piston and valve body:

• Remove the thermostat.

• Lift the piston out with a needle-nose pliers and remove the spring.

• Any cleaner suitable for brass and stainless steel may be used (if cleaning with suitable cleaner

is not sufficient to remove debris, a 400-grit sandpaper may be used to polish and hone the

piston and valve body).

• Snap spring into piston (will detent) and reassemble into the valve body. Retest the piston.

3. If, after a thorough cleaning, the piston does not move freely, the piston must be replaced.

Contact your Bradley representative and ask for Repair Kit (part number S65-259).

Problem: External leaks in the system

Cause: O-rings have been damaged.

Solution: Replace O-rings where necessary. For replacement of the O-rings, contact your

Bradley representative and ask for Repair Kit (part number S65-259).

Problem: Improper water temperature or temperature fluctuation

Cause: Thermostat is slowly failing or not working at all.

Solution: Check the thermostat for proper operation.

1. At room temperature (80° F or less) remove cap and thermostat.

2. Place thermostat into container with 115° F water. The pushrod should pop out of the

thermostat approximately 1/10".

3. If thermostat pushrod does not pop out, the thermostat must be replaced. Contact your Bradley

representative and ask for Repair Kit (part number S65-259).

Cause: Valve temperature is not properly set.

Solution: Adjust the temperature. Using a blade screwdriver, turn the adjustment stem

counterclockwise to increase the temperature or clockwise to decrease the temperature.

Terreon® Quadra-Fount® Washfountain with Touch Time® Control

MF2944/TT Installation Instructions

Bradley Corporation • 215-1539 Rev. A; EN 03-063

16 12-18-2003

Strainer

Valve Body

Spring

Thermostat

Piston

Stem

O-Ring

2 1 Spring

3 1 Piston

4 1 Thermostat

6 1 O-Ring

7 1 O-Ring

Item Qty Description

173-028 Strainer

Repair Kit S65-259

Cap

Nut 3/8-24 Hex Jam

Figure 12

Navigator

Thermostatic Mixing Valve (S01-520)

Bradley Terreon Quadra-Fount Washfountain MF2944/TT Installation Instructions Manual

Brand: Bradley

Model: Terreon Quadra-Fount Washfountain MF2944/TT

Category: Sanitary ware

Type: Installation Instructions Manual

This manual is also suitable for

Terreon Tri-Fount MF2933/IR

Download PDF

report

Bradley Terreon Quadra-Fount Washfountain MF2944/TT Installation Instructions Manual

This manual is also suitable for

Bradley Terreon Quadra-Fount Washfountain MF2944/TT Installation Instructions Manual

Related papers

Other documents