Drive Flex 'N Go Cane Tip Owner's manual

Type
Owner's manual

This manual is also suitable for

1. Remove the Flex N Go tip and
allen key from the blister package
(Figure 1).
2. Remove the black rubber plug
from the bottom of the tip (Figure 2).
3. Slide the Flex N Go tip into the
bottom of the cane.
Note: The existing cane tip must be
removed first (Figure 3).
4. Tighten the screw by turning the
allen key clockwise until tight.
DO NOT over tighten (Figure 4).
5. Replace the plastic plug into the
bottom of the tip (Figure 5).
Assembly Instructions
1.Remove the flexy foot & T allen key
f
rom packaging blister (Figure 1).
4
5
3
2
6
1
2.Take out the plastic plug (Figure 2).
3
.Put the flexy foot into the cane tube
(Figure 3).
4.Tig
hten the screw using T allen key
t
o torque force 60 kgf.cm (Figure 4).
6
. Complete cane assembly with the
flexy foot(Figure 6).
5
. Attach the plug on the flexy foot,
m
ake sure it won't fall off (Figure 5).
Figure 1
Assembly Instructions
1.Remove the flexy foot & T allen key
f
rom packaging blister (Figure 1).
4
5
3
2
6
1
2.Take out the plastic plug (Figure 2).
3
.Put the flexy foot into the cane tube
(Figure 3).
4.Tig
hten the screw using T allen key
t
o torque force 60 kgf.cm (Figure 4).
6
. Complete cane assembly with the
flexy foot(Figure 6).
5
. Attach the plug on the flexy foot,
m
ake sure it won't fall off (Figure 5).
Figure 2
Assembly Instructions
1.Remove the flexy foot & T allen key
f
rom packaging blister (Figure 1).
4
5
3
2
6
1
2.Take out the plastic plug (Figure 2).
3
.Put the flexy foot into the cane tube
(Figure 3).
4.Tig
hten the screw using T allen key
t
o torque force 60 kgf.cm (Figure 4).
6
. Complete cane assembly with the
flexy foot(Figure 6).
5
. Attach the plug on the flexy foot,
m
ake sure it won't fall off (Figure 5).
Figure 3
Assembly Instructions
1.Remove the flexy foot & T allen key
f
rom packaging blister (Figure 1).
4
5
3
2
6
1
2.Take out the plastic plug (Figure 2).
3
.Put the flexy foot into the cane tube
(Figure 3).
4.Tig
hten the screw using T allen key
t
o torque force 60 kgf.cm (Figure 4).
6
. Complete cane assembly with the
flexy foot(Figure 6).
5
. Attach the plug on the flexy foot,
m
ake sure it won't fall off (Figure 5).
Figure 4
Assembly Instructions
1.Remove the flexy foot & T allen key
f
rom packaging blister (Figure 1).
4
5
3
2
6
1
2.Take out the plastic plug (Figure 2).
3
.Put the flexy foot into the cane tube
(Figure 3).
4.Tig
hten the screw using T allen key
t
o torque force 60 kgf.cm (Figure 4).
6
. Complete cane assembly with the
flexy foot(Figure 6).
5
. Attach the plug on the flexy foot,
m
ake sure it won't fall off (Figure 5).
Figure 5
INSTALLATION
INSTRUCTIONS
1. Retire la punta de Flex N Go y llave
allen del blister (Figura 1).
2. Retire el tapón de goma negro de
la parte inferior de la punta
(Figura 2).
3. Deslice la punta Flex N Go en la
parte inferior de la caña. Nota: La
punta de la caña existente debe
retirarse primero (Figura 3).
4. Apriete el tornillo girando en
sentido horario allen hasta que
quede apretado.
NO apriete demasiado (Figura 4).
5. Reemplace el tapón de plástico en
la parte inferior de la punta
(Figura 5).
INSTRUCCIONES DE
INSTALACIÓN
1. Retirez la pointe Flex N Go et
une clé Allen de l’emballage blister
(Figure 1).
2. Retirer le bouchon de caoutchouc
noir à partir du bas de la pointe
(Figure 2).
3. Faites glisser la pointe Flex N Go
dans le fond de la canne.
Remarque: La pointe de canne
existant doit être retiré en premier
(figure 3).
4. Serrez la vis en tournant la clé dans
le sens horaire jusqu’à ce que allen
serré. NE PAS trop serrer (figure 4).
5. Remettre le bouchon en plastique
dans le bas de la pointe (Figure 5).
INSTRUCTIONS
D’INSTALLATION
  • Page 1 1

Drive Flex 'N Go Cane Tip Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI