Biostar PT890 Owner's manual

PT890 775 SE Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide re asonable protec tion against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particular ins talla tion.

The ve ndor makes no representations o r warranties with respec t to the

contents here and specially disclaims any implied warranties of merchantability

o r fi tnes s fo r a ny purpos e . F urt he r t he ve ndo r rese rves t he ri g ht to rev is e t his

publication and to make changes to the contents here without obligation to

notify any party beforehand.

D uplication of this publication, in part or in whole , is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be res ponsible for any mis takes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction .............................................3

1.1 Before You Start................................................................... 3

1.2 Package Checklist................................................................3

1.3 Motherboard Features..........................................................4

1.4 Rear Panel Connectors (for Ver 6.x)....................................... 6

1.5 Rear Panel Connectors (for Ver 5.x).......................................6

1.6 Motherboard Layout (for Ver 6.x).......................................... 7

1.7 Motherboard Layout (for Ver 5.x).......................................... 8

Chapter 2: Hardware Installation..............................9

2.1 Installing Central Processing Unit (CPU)................................9

2.2 FAN Headers.......................................................................11

2.3 Installing System Memory.....................................................12

2.4 Connectors and Slots............................................................13

Chapter 3: Headers & Jumpers Setup .....................15

3.1 How to Setup Jumpers..........................................................15

3.2 Detail Settings.....................................................................15

Chapter 4: RAID Functions.......................................21

4.1 Operation System................................................................21

4.2 Raid Arrays.........................................................................21

4.3 How RAID Works.................................................................21

Chapter 5: Useful Help .............................................23

5.1 Driver Installation Note .......................................................23

5.2 Award BIOS Beep Code........................................................24

5.3 Extra Information................................................................24

5.4 Troubleshooting...................................................................26

Chapter 6: WarpSpeeder™ .......................................27

6.1 Introduction........................................................................27

6.2 System Requirement............................................................27

6.3 Installation.........................................................................28

6.4 WarpSpeeder™....................................................................29

Appendencies: SPEC In Other Language ................36

German................................................................................................36

France..................................................................................................38

Italian..................................................................................................40

Spanish................................................................................................42

Portuguese...........................................................................................44

Polish...................................................................................................46

Russian................................................................................................48

Arabic..................................................................................................50

Japanese..............................................................................................52

PT890 775 SE

3

CHAPTER 1: INTRODUCTION

1.1 BEFORE YOU START

Tha nk you for choosing our pro duct. Be fore you start installing the

mo the rboa rd, plea se make sure you fo llo w the instructions be low:

 Prepare a dry and stable working environment with

s uf ficie nt ligh ting .

 Always disconnect the computer from power outlet

be fo re ope ra tion.

 Befo re you take the mo the rboa rd ou t f rom a n ti-s ta ti c

bag, ground yourself properly by touching any safely

grounde d appliance, o r use grounded wrist strap to

remove the static charge.

 Avo id tou ch ing the compone nts o n m o the rboa rd o r the

rear side of the board unless necessa ry. Hold the board

on the edge , do not try to bend or flex the board.

 Do not leave any unfastened small pa rts inside the

case after installation. Loose parts will cause short

circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source , humid a ir and wate r.

1.2 PACKAGE CHECKLIST

FDD Cable X 1

HDD Cable X 1

Use r’s Manua l X 1

Fully Setup Driver CD X 1

Rear I/O Panel for ATX Case X 1

Se ria l ATA Cab le X 1 (op tiona l)

Se ria l ATA Po we r Switch Cab le X 1 (op tiona l)

USB 2.0 Cable X1 (optional)

S/PDIF Cable X 1 (optional)

Motherboard Manual

4

1.3 MOTHERBOARD FEATURES

Ver 5.x Ver 6.x

CPU

LGA 77 5

Intel Core2Duo/ Pentium 4 / Pentium D /

Celeron D processor up to 3.8 GHz

Supports Hy per -Thre adin g / Exec ute

Disable Bit/ Enhanced Intel S peedStep® /

Intel Extended Memory 64 technology

LGA 77 5

Intel Core2Duo/ Pentium 4 / Pentium D /

Celeron D processor up to 3.8 GHz

Supports Hy per -Thre adin g / Exec ute

Disable Bit/ Enhanced Intel S peedStep® /

Intel Extended Memory 64 technology

FSB 400 / 533 / 8 00 / 10 66 MHz 400 / 533 / 8 00 / 10 66 MHz

Chipset

VIA PT890

VIA VT8237A

VIA PT890

VIA VT8237A

Super I/O

ITE IT 87 12F

Provides the most commonly used legacy

Super I/O functionality.

Low Pin C ount Interf ac e

Environment Control initiatives,

H/W Monitor

Fan Spee d Co ntroller

ITE's "Smart G uardia n" fu nction

ITE IT 87 12F

Provides the most commonly used legacy

Super I/O functionality.

Low Pin C ount Interf ac e

Environment Control initiatives,

H/W Monitor

Fan Spee d Co ntroller

ITE's "Smart G uardia n" fu nction

Main

Memory

DIMM Slots x 2

Supports D DR2 4 00 / 533

Eac h DIMM sup ports 2 56/ 51 2MB/1GB/ 2GB

DDR2

Max Memory Capicity 4GB

Single Channel Mode DDR2 memory

module

Registered DIMM and ECC DIMM is not

supported

DIMM Slots x 2

Supports D DR2 4 00 / 533

Eac h DIMM sup ports 2 56/ 51 2MB/1GB/ 2GB

DDR2

Max Memory Capicity 4GB

Single Channel Mode DDR2 memory

module

Registered DIMM and ECC DIMM is not

supported

IDE

Integrated IDE Controller

Ultra DMA 33~133 Bus Master Mode

supports PIO Mo de 0~4,

Integrated IDE Controller

Ultra DMA 33~133 Bus Master Mode

supports PIO Mo de 0~4,

SATA

Integrated Serial ATA Controller

Data transfer rates up to 1.5 Gb/s.

SATA Version 1.0 specification compliant.

Integrated Serial ATA Controller

Data transfer rates up to 1.5 Gb/s.

SATA Version 1.0 specification compliant.

PT890 775 SE

5

Ver 5.x Ver 6.x

LAN PHY

Realtek RTL 8201CL

10 / 100 Mb/s auto negotiation

Half / Full duplex capability

Realtek RTL 8201CL

10 / 100 Mb/s auto negotiation

Half / Full duplex capability

Sound

Codec

ALC888

7.1 cha nnels a udio o ut

High Defi nition Audio

ALC861VD

5.1 cha nnels a udio o ut

High Defi nition Audio

PCI Express x 16 slot x1 PCI Express x 16 slot x1

PCI Express x 1 slot x1 PCI Express x 1 slot x1 Slots

PCI slot x4 PCI slot x4

Floppy connector x1 Floppy connector x1

IDE Co nnector x2 IDE Co nnector x2

Printer Port C onnector x1 Printer Port C onnector x1

SATA Connector x2 SATA Connector x2

Front Pa nel Co nnec tor x1 Front Pa nel Co nnec tor x1

Front Audi o Co nnector x1 Front Audi o Co nnector x1

CD-in Co nnector x1 CD-in Co nnector x1

S/PDIF out connector x1 S/PDIF out connector x1

CPU Fan hea der x1 CPU Fan hea der x1

System Fan hea der x1 System Fan hea der x1

Clear CMOS header x1 Clear CMOS header x1

USB connector x2 USB connector x2

Power Connector (24pin) x1 Power Connector (24pi n) x1

On Board

Connector

Power Connector (4pin) x1 Power Connector (4pin) x1

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mo use x1

Serial Port x1

LAN port x1

USB Port x4

Audio Jack x6

PS/2 Keyboard x1

PS/2 Mo use x1

Serial Port x1

LAN port x1

USB Port x4

Audio Jack x3

Board Size 190 mm (W) x 29 4 mm (L) 190 mm (W) x 294 mm (L)

Special

Features

RAID 0 / 1 support RAID 0 / 1 support

OS

Support

Windows 2000 / XP / VISTA

Biostar Reserves the ri

g

ht to add or remo ve

support for any OS with or without notice.

Windows 2000 / XP / VISTA

Biostar Reserves the ri

g

ht to add or remove

support for any OS with or without notice.

Motherboard Manual

6

1.4 R

EAR PANEL CONNECTORS (FOR VER 6.X)

PS /2

Mouse

PS /2

Keyboard

USBX2USBX2

LA N

COM1

L ine In/

Su rr oun d

Lin e Ou t

Mic In 1/

Bass/ Center

1.5 REAR PANEL CONNECTORS (FOR VER 5.X)

PS/2

Mou se

PS/ 2

Keyboard

USBX2USBX2

LAN

COM1

Li ne In

Li ne Ou t

Mic In

Center

Rear

Side

PT890 775 SE

7

1.6 MOTHERBOARD LAYOUT (FOR VER 6.X)

JKBMS1

C

O

M

1

J

C

O

M

1

JU SB 1

JUSBLAN1

JAUDIO1

Super

I/O

BIOS

Codec

JCDIN1

J SPD IF_ OUT1

PCI3

PCI4

PCI2

PCI1

PCI-EX1 _1

BAT1

PC I- EX 16

JAUDIOF1

JUSBV1

LA N

JATXP W R2

LGA775

CPU 1

VIA

PT890

DI MM1

DIMM2

JCFAN1

J ATXPW R1

IDE 1

IDE 2

JS ATA1

JSATA2

FDD1

JPANEL 1

JS FAN1

JCMOS1

JPR NT1

VIA

VT8237A

JUSB2

JUS B3

J USBV2

Note: represents the 1■

st

pin.

Motherboard Manual

8

1.7 MOTHERBOARD LAYOUT (FOR VER 5.X)

JKBMS1

C

O

M

1

J

C

O

M

1

JU SB 1

JUSBLAN1

JAUDIO2

Super

I/O

BIOS

Codec

JCDIN1

J SPDIF_ OUT1

PCI3

PCI4

PCI2

PCI1

PCI-EX1 _1

BAT1

PC I- EX 1 6

JAUDIOF1

JUSBV1

LA N

JATXP W R2

LGA775

CPU 1

VIA

PT890

DI MM1

DIMM2

JCFAN1

J ATXPW R1

IDE 1

IDE 2

JS ATA1

JSATA2

FDD1

JPANEL 1

JS FAN1

JCMOS1

JPR NT1

VIA

VT8237A

JUSB2

JUS B3

J USBV2

Note: represents the 1■

st

pin.

PT890 775 SE

9

CHAPTER 2: HARDWARE INSTALLATION

2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)

Special Notice:

Remove Pin Cap before installation, and make good preservation

for future use. When the CPU is removed, cover the Pin Cap on the

empty socket to ensure pin legs won’t be damaged.

Pin Cap

Step 1: Pull the socket locking lever out from the socket and then raise

the lever up to a 90-degree angle.

Motherboard Manual

10

Step 2: Look for the triangular cut edge on socket, and the golden dot on

CPU should point forwards this triangular cut edge. The CPU will

fit only in the correct orientation.

Step 2-1:

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked

position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it

on the retention frame. Connect the CPU FAN power cable into

the JCFAN1. This completes the installation.

PT890 775 SE

11

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

JCFAN1: CPU Fan Header

Assignment

1 Ground

2 +12V

3 FAN RPM rate

sense

14

JCFAN1

4 Smart Fan

Control

JSFAN1: System Fan Header

Assignment

1 Ground

2 +12V

13

JSFAN1

3 FAN RPM rate

sense

Note:

The JCFAN1 a nd JSFAN1 s up port 4-pin and 3-pin h ead co nnec tors. When c on necti ng

with wires ont o c onnect or s, ple ase no te tha t t he r e d wir e is t he positi ve and s houl d b e

conn ecte d t o pi n#2, and th e bl ac k wire is Gr o und a nd s ho uld b e c on nect ed to Gr ound.

Motherboard Manual

12

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DIMM1

DIMM2

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

B. Memory Capacity

DIMM Socket

Location

DDR Module

To tal Memo r y

Size

DIMM1 256MB/512MB/1GB/2GB

DIMM2 256MB/512MB/1GB/2GB

Max is 4GB.

PT890 775 SE

13

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard prov ides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk ty pes. This connector supports the

prov ided f loppy drive ribbon cables.

34

33

1

2

IDE1/IDE2: Hard Disk Connectors

The motherboard has a 32-bit Enhanced PCI IDE Controller that prov ides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 f unctionality. It has two

HDD connectors IDE1 (primary) and IDE2 (secondary).

The IDE connectors can connect a master and a slav e driv e, so you can

connect up to four hard disk drives. The f irst hard drive should always be

connected to IDE1.

IDE2IDE1

21

3940

Motherboard Manual

14

PCI-EX16: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, f or an aggregate of 8GB/s totally.

PCI-EX1_1: PCI-Express x1 slots

- PCI-Express 1.0a compliant.

- Data transf er bandwidth up to 250MB/s per direction; 500MB/s in total.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth ov er the traditional PCI architecture.

PCI-EX16

PCI-EX1_1

PCI1~PCI4: Peripheral Component Interconnect Slots

This motherboard is equipped with 4 standard PCI slots. PCI stands f or

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI3

PCI4

PCI1

PCI2

PT890 775 SE

15

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 HOW TO SET UP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SET T ING S

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep

button and speaker connection. It allows user to connect the PC case’s f ront

panel switch functions.

1

8

16

SLP

PWR_LED

On/Off

RST

HLED

SPK

++

+

9

-

Pin Assignment Function Pin Assignment Function

1 +5V 9 Sleep control

2 N/A 10 Ground

Sleep button

3 N/A 11 N/A N/A

4 Speaker

Speaker

Connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive

LED

14 P ower LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

Motherboard Manual

16

ATX Power Source Connector: JATXPWR1

JATXPWR1 allows user to connect 24-pin power connector on the ATX power

supply.

1

12

13

24

Pin Assignment Pin Assignment

13 +3.3V 1 + 3.3V

14 -12V 2 +3.3V

15 Gr oun d 3 Groun d

16 PS_ON 4 +5V

17 Gr oun d 5 Groun d

18 Gr oun d 6 + 5V

19 Gr oun d 7 Groun d

20 NC 8 PW_OK

21 +5V 9 Stand b y Volt ag e+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Gr oun d 12 +3.3V

JATXPWR2: ATX Power Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

12

34

4 Ground

PT890 775 SE

17

JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC f ront panel,

and also can be connected with internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

1

2

9

10

JUSB2

JUSB3

10 NC

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at JUSBLAN1/JUSB1.

JUSBV2: +5V for USB ports at f ront panel (JUSB2/JUSB3).

Pin 2-3 Close:

JUSBV1: USB ports at JUSBLAN1/JUSB1 are powered by +5V standby

v oltage.

JUSBV2: USB ports at front panel (JUSB2/JUSB3) are powered by +5V

standby v oltage.

31

1

3

Pin 1-2 close

1

3

13

JUSBV1

JUSBV2

3

1

3

Pin 2-3 close

Note:

In ord er to s upport this f unctio n “P ower-On s yst em vi a USB devic e,” “JUSBV1 / JUSB V2”

jumper ca p sh ould be plac ed on Pin 2-3 in di vidu all y.

Motherboard Manual

18

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC f ront

panel. It will disable the output on back panel audio connectors.

Pin Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

10 Jack Sense

1

210

9

JCDIN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source f rom the v ariaty dev ices,

like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.

Assignment

1 Left Channel Input

2 Ground

3 Ground

14

4 Right Channel Input

PT890 775 SE

19

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS saf e setting

and the CMOS data, please carefully f ollow the procedures to avoid damaging

the motherboard.

13

Pin 1-2 Close:

Normal Operation (default).

13

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remov e AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for f ive seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset y our desired password or clear the CMOS data.

JSATA1/JSATA2: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 2 channels SATA interf ace,

it satisfies the SATA 1.0 spec and with transfer rate of 1.5Gb/s.

Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

147

J SATA1

JSATA2

7 Ground

Motherboard Manual

20

JSPDIF_OUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Assignment

1 +5V

2 SPDIF_OUT

13

3 Ground

JPRNT1: Printer Port Connector

This header allows you to connect printer on the PC.

1

2

25

Pin Assignment Pin Assignment

1 -Strobe 14 Groun d

2 -ALF 15 Data 6

3 Data 0 16 Groun d

4 -Error 17 Data 7

5 Data 1 18 Groun d

6 -Init 19 - ACK

7 Data 2 20 Groun d

8 -Scltin 21 Bus y

9 Data 3 22 Groun d

10 Gr oun d 23 PE

11 Data 4 24 Groun d

12 Gr oun d 25 SCLT

13 Data 5 26 Ke y

Page is loading ...

Biostar PT890 Owner's manual

Biostar PT890 Owner's manual

Related papers

Other documents